EN
Universal Remote Control logo
Official user manual

Universal Remote Control MX-900

44 pages·1.9 MB·Universal Remote·PDF·ENDEFRITNLJA
Universal Remote Control MX-900
Table of Contents 34 sections Cover · Copyright Notice · Hyperlinked Table of Contents · The MX-950 “Core Engine” · … ShowHide
Page 1 of the Universal Remote Control MX-900 user manual — Programming Manual for the MX-950, MX-900 and TX-1000
Page 1 · click to enlarge
Page 1

Programming Manual for the MX-950, MX-900 and TX-1000

Unleashing the MX-950 Core Engine

Universal Remote Control MX-900 — Programming Manual for the MX-950, MX-900 and TX-1000 diagram (page 1)
Fig. 1 · Programming Manual for the MX-950, MX-900 and TX-100…

Universal Remote Control BY ®

™

Page 2 of the Universal Remote Control MX-900 user manual — Copyright Notice
Page 2 · click to enlarge
Page 2

Programming Manual for the MX-950, MX-900 and TX-1000 © 2006 Universal Remote Control, Inc.

The information in this manual is copyright protected. No part of this manual may be copied, reproduced or dis- tributed in any form without prior written consent from Universal Remote Control, Inc. unless you are an AUTHORIZED seller by prior written consent from Universal Remote Control, Inc. UNAUTHORIZED sellers dis- tributing this manual via EMAIL or the INTERNET are LIABLE for copyright violation!

UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORI- AL ERRORS/OMISSIONS MADE IN THIS MANUAL.

The information in this manual may be subject to change without prior notice.

Complete Control is a registered trademark of Universal Remote Control, Inc. Entertainment Made Simple is a trademark of Universal Remote Control, Inc. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.

500 Mamaroneck Avenue Harrison, NY 10528 Phone: (914) 835-4484

Fax(914) 835-4532

www.universalremote.com

Page 3 of the Universal Remote Control MX-900 user manual — Hyperlinked Table of Contents
Page 3 · click to enlarge
Page 3
Universal Remote Control MX-900 — Hyperlinked Table of Contents diagram (page 3)
Fig. 2 · Hyperlinked Table of Contents

THE MX-950 “CORE ENGINE” 1

WHAT’S COMMON? SPEED!!! 1

A. New File, Existing File on PC or in Remote 4

CREATING, NAMING AND ARRANGING DEVICES 5

Setting the Backlight Color of Each Device (MX-950 and TX-1000 Only) 6

Applying a “Set” of IR Commands to each Device 8

FINDING DISCRETE COMMANDS FOR RELIABLE MACROS 11

Use the IR Database Navigator to Find Discrete Commands 11

Use the Universal Browser to find Discrete IR Commands 13

TEST ALL COMMANDS AND RELABEL FOR EASY OPERATION 15

Using the LCD Button Editor to Relabel and Re-arrange Buttons 15

Using Page View to Relabel and Re-arrange Buttons 17

Page 4 of the Universal Remote Control MX-900 user manual — Hyperlinked Table of Contents
Page 4 · click to enlarge
Page 4
Universal Remote Control MX-900 — Hyperlinked Table of Contents diagram (page 4)
Fig. 3 · Hyperlinked Table of Contents

Finding Workarounds When There Are NO Discrete Codes 24

USING SOUNDS (MX-950 ONLY) 34

USING THE IMAGE GALLERY (MX-950 ONLY) 34

Adding RF Base Stations, Conguring ID#’s and Front Blasters 37

ENABLE OR DISABLE STANDALONE EDITING 38

Page 5 of the Universal Remote Control MX-900 user manual — 1 The MX-950 “Core Engine”
Page 5 · click to enlarge
Page 5

1 The MX-950 “Core Engine”

The MX-950 “Core Engine”

Universal Remote Control MX-900 — 1 The MX-950 “Core Engine” diagram (page 5)
Fig. 4 · 1 The MX-950 “Core Engine”

New Programming Features: All three applications, MX-950, MX-900 and TX-1000 share all the convenience and speed of MX-3000 Editor combined with the simple, straightforward interface of the MX-850. You’ll find that many things that were diffi- cult or impossible to do with MX-850 are now very easy to do with the MX-950 Core Engine:

Drag and Drop single IR Commands without creating a new device Multiple page jumps during macros for easy programming of Status Messages Better Text display. TX-1000 allows six characters per label, MX-900 allows seven and MX-950 allows up to eleven! Nesting - All three remotes enable you to modularzie your code with one macro “nested” as a single step inside another macro. No need for Shortcuts - If you need a ROUTED command from one device on another device, record a macro of a single step. This will respond exactly the way the original button does, including repeating while the button is held, but is routed via the original commands routing. All three remotes can now be programmed with a Navigate - Page jump, which allows you to pro- gram buttons with a BACK button that takes them back to the last device they were on.

Key Differences:

Only MX-950 and TX-1000 can change the color of the backlighting per device. MX-900 has blue backlighting only. Only MX-950 can change the TEXT label of a button during a macro. Only MX-950 can use GRAPHICS on the LCD screen. Only MX-950 can use SOUNDS in macros. Only MX-950 can use VARIABLES in macros.

What’s Common? SPEED!!! · ™

Page 6 of the Universal Remote Control MX-900 user manual — The TX-1000 Editor Window
Page 6 · click to enlarge
Page 6
Universal Remote Control MX-900 — The TX-1000 Editor Window diagram (page 6)
Fig. 5 · The TX-1000 Editor Window
Page 7 of the Universal Remote Control MX-900 user manual — F
Page 7 · click to enlarge
Page 7

3 MX-950 Editor Window

The MX-950 Editor Window

Universal Remote Control MX-900 — 3 MX-950 Editor Window diagram (page 7)
Fig. 6 · 3 MX-950 Editor Window

A

D

Edit Buttons

Simulate View

Window

Macro Window

B

Tree View

F

A

Menus and Shortcut buttons for common tasks. The Program Menu activates each task in the correct order.

B

Tree View of your configuration. Double clicking on any page enables you to quickly display that page on the simulator view. Right clicking on a device or page activates a context menu. The Simulate View is used to navigate and to select a button to program, edit or record a macro.

D

Edit and Label Buttons window is used to control a buttons graphics, text and activation.

The Macro window is used to view and edit macros.

F

The information bar displays whether your keyboard is cap locked or num locked.

The important thing to remember as you program is that most Windows conventions hold true in all URC Editors. Explore the program menus. Hover your mouse over most of the buttons and controls and a balloon will appear with a hint as to purpose. Navigate around the program window and explore a little before you begin programming.

Introducing MX-950 Editor · ™

Page 8 of the Universal Remote Control MX-900 user manual — 4 Type in Section Title
Page 8 · click to enlarge
Page 8

4 Type in Section Title

A. New File, Existing File on PC or in Remote

NEW - Starting from scratch on a new job, go to the File Menu, choose New from the File Menu and pick either the default file or a blank file. The default template is pre-programmed with IR commands and is useful for quick testing, but everything will have to be reprogrammed for your system. A blank file is completely empty. It is really personal preference which way you start.

OPEN - Open a configuration that you have worked on before and saved onto the PC hard drive.

UPLOAD - Get a file from a client’s remote control that another installer created. Now, you can save the file on your laptop, make any edits or changes as the client requests or the jobsite requires.

B. Use SAVE AS

The templates files are simply configuration files that have been preprogrammed for you. They will keep any changes you make. Utilize Save As to make a new file with a new file name. All configuration files are saved with the file extension .mxa.

Use the customer’s name and a rev # (i.e. SmithTheaterRev1.mxa)

C. Use the Program Menu

The Program Menu is your lifeline to a fast, easy programming experience. Follow the steps in the order shown in the Menu for best results. Typically, you will download to the remote control several times throughout this process and test what you have done so far. You’ll need to download after finishing all pro- gramming. For macro playback to work, you need to have downloaded. These downloads are not listed in the steps here in the Program Menu and are not automatically done for you.

Universal Remote Control MX-900 — 4 Type in Section Title diagram (page 8)
Fig. 7 · 4 Type in Section Title

It is important that you do all of the tasks for each step before moving on to the next step. Keep this manual handy so that you can verify that you have com- pleted all of your tasks.

D. Save and Reuse Customer Files

Archive and save your customer files. Programming systems with similar components gets even faster when you don’t have to redo your work over and over. You have your own ideas about what buttons should be labeled and how they should be arranged. You’ll save all of your work and reuse it on the next job with simi- lar components and devices.

E. Download to both Remote Controls

Test the file before training your client.

Universal Remote Control MX-900 — 4 Type in Section Title diagram (page 8)
Fig. 8 · 4 Type in Section Title

Programming Overview · Programming Overview

Page 9 of the Universal Remote Control MX-900 user manual — 5 Type in Section Title
Page 9 · click to enlarge
Page 9

Creating, Naming and Arranging Devices

5 Type in Section Title

Creating, Naming and Arranging Devices

A device is the basic grouping of a set of hard buttons and up to 255 soft button pages. You will need one device group for each remote control that the MX-950 is replacing. You can have a maximum of 255 devices in your configuration. When you create devices in the Create and Name Devices window, every device is automatically linked with a jump-link to the device via either the WATCH or the LISTEN menu. If you create devices manually you have to create a jump link from either the WATCH or the LISTEN menu button to each device manually.

Open the Create and Name Devices Window

You can open the Create and Name Devices window by clicking on the first item of the Program Menu or by clicking on the Toolbar icon as shown here:

Universal Remote Control MX-900 — 5 Type in Section Title diagram (page 9)
Fig. 9 · 5 Type in Section Title
Universal Remote Control MX-900 — 5 Type in Section Title diagram (page 9)
Fig. 10 · 5 Type in Section Title

1 After the Create and Name devices window appears, select the WATCH or the LISTEN menu from the Device list box:

Universal Remote Control MX-900 — 5 Type in Section Title diagram (page 9)
Fig. 11 · 5 Type in Section Title

2 MX-950 Only: Select the button position you’d like to create a new device name in by clicking on it. Now, decide if you need a double column or a single column label. A single column label can have up to 5 characters, a double column label up to 11 characters. When you combine a button, IR command or Macro programming will be duplicated automatically on both the left and the right button.

Combine both left and right buttons into one double column button.

Universal Remote Control MX-900 — 5 Type in Section Title diagram (page 9)
Fig. 12 · 5 Type in Section Title

Separate a double column button into two separate buttons.

3 Now, select the LISTEN menu from the Device List box and create all the devices for listening.

Universal Remote Control MX-900 — 5 Type in Section Title diagram (page 9)
Fig. 13 · 5 Type in Section Title

Creating Devices · ™

Page 10 of the Universal Remote Control MX-900 user manual — Setting the Backlight Color ...
Page 10 · click to enlarge
Page 10
Universal Remote Control MX-900 — Setting the Backlight Color ... diagram (page 10)
Fig. 14 · Setting the Backlight Color ...

3 You must hit the SAVE button to create all the new devices.

4 Tree View reveals the new devices you’ve created and the simulator shows the new WATCH page, with all the new device buttons displayed.

5 Select SAVE from the File menu or click on the SAVE icon on the toolbar.

Setting the Backlight Color of Each Device (MX-950 and TX-1000 Only)

1 Right click on any device in Tree View (including the WATCH or the LISTEN device). Select Backlight Color from the context menu that appears.

Page 11 of the Universal Remote Control MX-900 user manual — Setting the Backlight Color ...
Page 11 · click to enlarge
Page 11
Universal Remote Control MX-900 — Setting the Backlight Color ... diagram (page 11)
Fig. 15 · Setting the Backlight Color ...

2 Uncheck the Use Default Color checkbox, by clicking on it.

3 Adjust the sliders to the new color setting, then click on OK to save your changes.

4 The new color now shows on the simulator.

Page 12 of the Universal Remote Control MX-900 user manual — Using the IR Database
Page 12 · click to enlarge
Page 12
Universal Remote Control MX-900 — Using the IR Database diagram (page 12)
Fig. 16 · Using the IR Database

Applying a “Set” of IR Commands to each Device

1 Open the Database Window - Select IR Database from the Program Menu or the Toolbar.

2 Device - In the first list box, MX-950 Editor lists the names of the devices you’ve created and named in your configuration. Select the device you would like to program from the list box.

2 IR Data From - Select the type or category of component (i.e. TV, VCR or DVD player) via the “IR Data From” listbox.

3 Brand - Select the company that made the component (i.e. B & K, Sony, Krell) by clicking on the correct brand name in the scrollable Brand window.

Page 13 of the Universal Remote Control MX-900 user manual — 9 Using the IR Database
Page 13 · click to enlarge
Page 13

9 Using the IR Database

4 Model - Select the exact model number from the scrollable Model window.

Universal Remote Control MX-900 — 9 Using the IR Database diagram (page 13)
Fig. 17 · 9 Using the IR Database

If the MODEL number isn’t there, DON’T test the other model numbers! Instead... Scroll to the bottom of the list of model numbers for your brand. There you will find a number of “Inclusive” Code Sets. These code sets are always labeled BRAND1, BRAND2 (i.e.. Motorola1, Motorola2). Each will operate many different model numbers. Generally speaking, if your component is a recent model, test the higher numbered Inclusive code sets first. Here’s what the inclusive code sets look like:

Universal Remote Control MX-900 — 9 Using the IR Database diagram (page 13)
Fig. 18 · 9 Using the IR Database

5 Test the Code Set

A. Verify the MX-950 is charged and connect it to the PC via the USB port. B. Point the connected MX-950 so that it is in range and within line of sight of the component.\ C. Power On the component. D. Select the model number or the Inclusive Code set in the model window. E. Click on the Test button as shown above. The only code you can test is the Power command. F. If the component DOESN’T power off, try the next Inclusive code set.

6 Once the component powers off, click on the Save button.

™

Page 14 of the Universal Remote Control MX-900 user manual — 10 Using the IR Database
Page 14 · click to enlarge
Page 14

10 Using the IR Database

7 After you click on the SAVE button, the LCD Button Editor appears, revealing the pages and codes that will be created. Re-arrange the codes by clicking and dragging any label to any blank position. In this screen shot, you can see that the Live TV DVR command is being dragged to an empty posi- tion on page one. This empty position was created by dragging some less important commands to page three.

Universal Remote Control MX-900 — 10 Using the IR Database diagram (page 14)
Fig. 19 · 10 Using the IR Database

8 Once you have placed the most important commands on page 1, and the less used commands on the other pages, click on the APPLY button.

9 Continue with the rest of the devices you need by clicking on the NEXT DEVICE button and repeat- ing steps two through eight.

Universal Remote Control MX-900 — 10 Using the IR Database diagram (page 14)
Fig. 20 · 10 Using the IR Database

10 When you have finished all of your devices, click on the CLOSE button.

Universal Remote Control MX-900 — 10 Using the IR Database diagram (page 14)
Fig. 21 · 10 Using the IR Database
Page 15 of the Universal Remote Control MX-900 user manual — 11 Finding Discrete Commands for Reliable Macros
Page 15 · click to enlarge
Page 15

11 Finding Discrete Commands for Reliable Macros

Finding Discrete Commands for Reliable Macros

Discrete Commands versus Toggle Commands When a remote control’s only button to turn on and off a TV set is labeled Power, it is usually a “toggle” com- mand. Test it by pressing the button twice. If the power button turns on the TV, then turns it off, it is a toggle command. You cannot predict whether the component will power on or not. That is a big problem when you are programming macros! Basically, your client will feel that the macro only works half the time, and will probably blame you for the problem.

Discrete means that the function of the command is “separate and distinct” from any other function. On a remote control with “discrete” power commands, there are two power buttons. One that only turns the com- ponent on, and another that only turns the component off.

The most commonly sought “discrete” commands are for power on, power off and for TV and Surround Sound Receiver INPUT selection. These discrete commands will make your macros work every time for your cus- tomer.

“Secret” Discrete Codes exist for some components. Why are they secret? Because the manufacturer wants the remote control that accompanies the component to have the simplest appearance (fewest buttons). Since toggles reduce the number of buttons, they make the remote control appear easier to operate. Many manufacturers understand the needs of custom installers and build their components to also respond to dis- crete codes. They distribute the discrete codes via service remotes, etc. For the first time, those codes are col- lected and integrated into our database.

Not all components respond to the discrete codes in the Database. A component has to be BUILT to respond to discrete codes. The fact that other models from the same manufacturer do respond to discrete codes is the reason the codes are added to a code set. However, some models will not respond, because the manu- facturer did not build it to respond through budgetary considerations, time constraints or a simple oversight.

Use the IR Database Navigator to Find Discrete Commands

1 Open the IR Database Navigator by clicking on the CUSTOM button in the IR Database window, or by clicking on IR Database Navigator in the TOOLS menu.

Universal Remote Control MX-900 — 11 Finding Discrete Commands for Reliable Macros diagram (page 15)
Fig. 22 · 11 Finding Discrete Commands for Reliable Macros
Universal Remote Control MX-900 — 11 Finding Discrete Commands for Reliable Macros diagram (page 15)
Fig. 23 · 11 Finding Discrete Commands for Reliable Macros

™

Page 16 of the Universal Remote Control MX-900 user manual — Use the IR Database Navigato...
Page 16 · click to enlarge
Page 16
Universal Remote Control MX-900 — Use the IR Database Navigato... diagram (page 16)
Fig. 24 · Use the IR Database Navigato...

2 Select the IR DATA FROM (category of component), then the BRAND, then the MODEL. If you do not see the model number, utilize the INCLUSIVE CODE SETS (i.e BRAND1, BRAND2, etc). Once you see a command that has a promising sounding name, click on it so that it is highlighted (select- ed), then click on the TEST button. You can test any IR command in the list.

3 When you find a command that you want, simply click and drag it to the button on the simulator.

Page 17 of the Universal Remote Control MX-900 user manual — 13 Finding Discrete Commands for Reliable Macros
Page 17 · click to enlarge
Page 17

13 Finding Discrete Commands for Reliable Macros

4 After you’ve dragged it to its new position, the new label and a pre-programmed code flag (the red dot) is placed on the button.

Universal Remote Control MX-900 — 13 Finding Discrete Commands for Reliable Macros diagram (page 17)
Fig. 25 · 13 Finding Discrete Commands for Reliable Macros

Many projectors require a two or three second burst to power on or off. You can program this to occur without the customer having to press and hold the button for several seconds by utilizing the repeat window in IR Database Navigator. Simply experiment with different numbers of repeats and test the command until it works as you want it to. There is no predictable relationship between the number of repeats and seconds from one brand to another, so start experimenting with 10 repeats and time the burst. Once you’ve pro- grammed a button with this extended IR command, you can use it in a macro. The timed burst will occur as a single macro step.

Universal Remote Control MX-900 — 13 Finding Discrete Commands for Reliable Macros diagram (page 17)
Fig. 26 · 13 Finding Discrete Commands for Reliable Macros

Use the Universal Browser to find Discrete IR Commands

Using the Universal Browser Window you can import LEARNED IR codes from a .ccf file, an .mxf file or an .rcc file. You cannot import any kind of Database codes, only LEARNED codes.

On the internet, you can find many unusual discrete codes by browsing the files section of a website popular with other custom installers:

www.remotecentral.com You can often find discrete codes by posting at one of many other sites popular with custom installers by post- ing on an online bulletin board. If any other custom installer knows of a solution he/she will email a file to you. Whether your download a file or if you are emailed a file from another installer, the Universal Browser enables you to import learned codes into your MX-950 configuration.

After you’ve saved the file to your PC, you use the Universal Browser as follows:

1 Open the Universal Browser by clicking on the Universal Browser in the TOOLS menu or by clicking on the shortcut button on the toolbar.

Universal Remote Control MX-900 — 13 Finding Discrete Commands for Reliable Macros diagram (page 17)
Fig. 27 · 13 Finding Discrete Commands for Reliable Macros

2 Click on the File icon to navigate to the folder that contains the file you’d like to get codes from.

Universal Remote Control MX-900 — 13 Finding Discrete Commands for Reliable Macros diagram (page 17)
Fig. 28 · 13 Finding Discrete Commands for Reliable Macros

™

Page 18 of the Universal Remote Control MX-900 user manual — Use the Universal Browser to...
Page 18 · click to enlarge
Page 18
Universal Remote Control MX-900 — Use the Universal Browser to... diagram (page 18)
Fig. 29 · Use the Universal Browser to...

3 Use Tree View to Navigate to the Panel containing LEARNED IR codes you want. Click on the panel name in Tree View to make the panel appear in Panel View.

4 Click on a button in Panel View and the Action List view will reveal whether it has Learned Data or not. Only buttons with Learned Data can be transferred.

5 Click and drag the button to the MX-950 simulator.

6 After you’ve dragged the button, the blue indicating a Learned IR command is displayed on the button.

Universal Remote Control MX-900 — Use the Universal Browser to... diagram (page 18)
Fig. 30 · Use the Universal Browser to...
Page 19 of the Universal Remote Control MX-900 user manual — 15 Test All Commands and Relabel for Easy Operation
Page 19 · click to enlarge
Page 19

15 Test All Commands and Relabel for Easy Operation

Test All Commands and Relabel for Easy Operation

Before programming any further, you should rigorously test all of the codes you have programmed using the IR Database and label the buttons with names that the customer will find easy to under- stand. The best approach is to download, test all the commands, and as you test, use MX-950 Editor to modify labels, and hide or delete unnecessary commands.

MX-950 Editor enables you to use two methods to relabel and re-arrange commands and labels. Use the LCD Button Editor method if you are most comfortable with MX-850 Editor. Use the Page View method if you are most comfortable with MX-3000 Editor. Both have their advantages as you will see in the descriptions below.

Using the LCD Button Editor to Relabel and Re-arrange Buttons

Begin testing the codes you downloaded to the MX-950. Make sure that you test all buttons (hard buttons and the LCD buttons on each page of every device). Don’t try to learn new commands yet, wait until you can do all of them at once systematically. First you must delete commands that don’t work and change the labeling so that your client instantly understands why you’ve made the button available to them. Good practice is to simply delete commands that the client will never use, or to arrange them on the last pages of a device. Certainly, your most important goal is to place the most useful commands on the first page of a device, so that the client has everything they need without pressing a PAGE button.

1 From the Program Menu, select Edit Buttons.

Universal Remote Control MX-900 — 15 Test All Commands and Relabel for Easy Operation diagram (page 19)
Fig. 31 · 15 Test All Commands and Relabel for Easy Operation

2 From the Device list box, select the first device you’d like to test and edit.

Universal Remote Control MX-900 — 15 Test All Commands and Relabel for Easy Operation diagram (page 19)
Fig. 32 · 15 Test All Commands and Relabel for Easy Operation

™

Page 20 of the Universal Remote Control MX-900 user manual — 16 Test All Commands and Relabel for Easy Operation
Page 20 · click to enlarge
Page 20

16 Test All Commands and Relabel for Easy Operation

Universal Remote Control MX-900 — 16 Test All Commands and Relabel for Easy Operation diagram (page 20)
Fig. 33 · 16 Test All Commands and Relabel for Easy Operation

3 Now drag any unimportant commands from the first page to the last page of the device.

4 Take a look at all the other pages, drag any buttons you consider important to the first page.

5 MX-950 Only: Select a button you’d like to convert to Single Column and click on the Single Column button at the top of the window.

Page 21 of the Universal Remote Control MX-900 user manual — 17 Test All Commands and Relabel for Easy Operation
Page 21 · click to enlarge
Page 21

17 Test All Commands and Relabel for Easy Operation

6 Select a button to relabel with a new easier to understand name and type it in.

Universal Remote Control MX-900 — 17 Test All Commands and Relabel for Easy Operation diagram (page 21)
Fig. 34 · 17 Test All Commands and Relabel for Easy Operation

7 Repeat Steps 2-6 and continue to test all commands for all of your devices by selecting a new device from the Device list box, then editing as needed. If you are missing a command and need to learn it, delete any buttons that you don’t need and relabel to prepare for learning.

SAVE exits the Edit and Label Buttons window, so you would have to reopen it if you haven’t finished editing all your devices.

Hiding Pages in LCD Button Editor

A hidden page is accessible during programming so you can teach commands to buttons on hidden pages and use them in macros. The interesting thing about hidden pages is that the end user cannot manually access the page using the PAGE button. You HIDE pages using the HIDE checkbox which appears at the bottom of each page in LCD Button Editor. Unlike MX-850 Editor, you can hide any page without hiding any other.

Using Page View to Relabel and Re-arrange Buttons

Begin testing the codes you downloaded to the MX-950. Make sure that you test all buttons (hard buttons and the LCD buttons on each page of every device). Don’t try to learn new commands yet, wait until you can do all of them at once systematically. First you must delete com- mands that don’t work and change the labeling so that your client instantly understands why you’ve made the button available to them. Good practice is to simply delete commands that the client will never use, or to arrange them on the last pages of a device. Certainly, your most important goal is to place the most useful commands on the first page of a device, so that the client has everything they need without pressing a PAGE button.

1 From the View Menu, select Page View Mode.

™

Page 22 of the Universal Remote Control MX-900 user manual — 18 Test All Commands and Relabel for Easy Operation
Page 22 · click to enlarge
Page 22

18 Test All Commands and Relabel for Easy Operation

2 In Tree View, expand the device you would like to EDIT. In Tree View Double Click on each page of the device to display them. You can have as many pages open as you like.

Universal Remote Control MX-900 — 18 Test All Commands and Relabel for Easy Operation diagram (page 22)
Fig. 35 · 18 Test All Commands and Relabel for Easy Operation

3 After you’ve opened all the pages you want to edit, go to the Window Menu and select “Tile”, “Cascade” or if you’d like to clean things up, “Close All”. Tile is usually the best option when lots of Pages are displayed.

4 Now drag any unimportant commands from the first page to the last page of the device.

Universal Remote Control MX-900 — 18 Test All Commands and Relabel for Easy Operation diagram (page 22)
Fig. 36 · 18 Test All Commands and Relabel for Easy Operation

4 Take a look at all the other pages, drag any buttons you consider important to the first page.

Universal Remote Control MX-900 — 18 Test All Commands and Relabel for Easy Operation diagram (page 22)
Fig. 37 · 18 Test All Commands and Relabel for Easy Operation

5 Select a button you’d like to convert to Single Column and click on the Single Column button at the top of the Button Name window.

Universal Remote Control MX-900 — 18 Test All Commands and Relabel for Easy Operation diagram (page 22)
Fig. 38 · 18 Test All Commands and Relabel for Easy Operation
Page 23 of the Universal Remote Control MX-900 user manual — 19 Test All Commands and Relabel for Easy Operation
Page 23 · click to enlarge
Page 23

19 Test All Commands and Relabel for Easy Operation

6 Select a button to relabel with a new easier to understand name and type it in.

Universal Remote Control MX-900 — 19 Test All Commands and Relabel for Easy Operation diagram (page 23)
Fig. 39 · 19 Test All Commands and Relabel for Easy Operation

7 Repeat Steps 2-6 and continue to test all commands for all of your devices by double clicking in Tree View, then editing the pages as needed. If you are missing a command and need to learn it, delete any buttons that you don’t need and relabel to prepare for learning.

Hiding Pages in Page View

A hidden page is accessible during programming so you can teach commands to buttons on hidden pages and use them in macros. The interesting thing about hidden pages is that the end user cannot manually access the page using the PAGE button. You HIDE pages by right clicking on a device in Tree View, then selecting Hide from the context menu that appears.

After you’ve hidden a page, the page is greyed out in Tree View.

Universal Remote Control MX-900 — 19 Test All Commands and Relabel for Easy Operation diagram (page 23)
Fig. 40 · 19 Test All Commands and Relabel for Easy Operation

Page 1 is Not Hidden

Page 2 is Hidden

Page 3 is about to be changed to Hidden via the right click con- text menu.

™

Page 24 of the Universal Remote Control MX-900 user manual — OR
Page 24 · click to enlarge
Page 24

20 Type in Section Title

Learning should be a last resort for professional installers. We make every effort to provide you with any codes you need via our database. If they are not, please make a note to email us at the first chance with the learned file you created, the type of device it is and the Brand and Model Number. If it is not a current model component, we would still like to add it to the database, but please note in your email the approximate age of the component. Please address your emails to:

IRDatabase@universalremote.com

When you have difficulty successfully teaching codes to the MX-950, always try these tips in the order below:

1. Fresh Batteries in the Original Remote Control - Weak batteries will cause MX-950 Editor to fail to correctly learn. Note that EVEN if the original remote still operates the component, the batteries can be too weak to produce a strong enough carrier for any learning remote control to detect!!!! When a code fails, replace the batteries FIRST!
2. Tap instead of Pressing and Holding - With buttons that the client will only tap when using, this may produce better results. Normally, you should press and hold.

OR

2. The “Flutter” Technique - If you are having problems with a Code that has to be sustained (like volume up or down), sometimes fluttering the button on the original remote at least seven times while you are learning will successfully teach the code.
3. Vary the Distance between the Remote and the Learning Sensor - We recommend that you start with a distance of half an inch between them. If no other technique works, try varying the distance by doubling it each attempt. Keep trying until you are at least 5 feet away.
4. Try Standalone Learning, see page 23.
5. Call our technical support department at 1-800-901-0800 to see if they have a cross reference for the brand and model you are using. If there isn’t a cross reference, they will ask you to ship the remote to our engineers so the codes can be added to the database.

Learning IR Codes One at a Time

When all you need is a code or two, this is the method to use. If you need to teach an entire set of codes from a remote control, skip to the Batch Learning section on page xx.

1 Connect the MX-950 to your PC and verify that the ActiveSync icon in the lower right hand corner of your PC screen is green.

Universal Remote Control MX-900 — OR diagram (page 24)
Fig. 41

Learning · Learning

Page 25 of the Universal Remote Control MX-900 user manual — 21 Type in Section Title
Page 25 · click to enlarge
Page 25

21 Type in Section Title

2 Select the button that you want to teach to by single clicking it on the simulator.

Universal Remote Control MX-900 — 21 Type in Section Title diagram (page 25)
Fig. 42 · 21 Type in Section Title

3 Click on the LEARN Tab or choose Learn from the Program. There will be a pause, while the PC communicates with the MX-950, then the info window will display “Ready”.

The Learn Button re-activates the Learning process when it auto- matically times out or if you want to re-learn a command. The Learning Information window prompts you when the system is Ready to learn a new command and when a learned com- mand is Good, or if it Fails.

Universal Remote Control MX-900 — 21 Type in Section Title diagram (page 25)
Fig. 43 · 21 Type in Section Title

The Learn Tab reveals the toolbar for Learning.

4 Press and hold the corresponding button on the original remote control while pointing it at the top of the MX-950 (head to head) with the remotes approximately a half inch to an inch apart. When the code is successfully learned, the window will say GOOD, confirming that the code learned “correct- ly.” Actually, the GOOD means that the code might be good You need to test it. Select the code in the Current Learned IR List, then click on the test button while pointing the MX-950 at the device.

Universal Remote Control MX-900 — 21 Type in Section Title diagram (page 25)
Fig. 44 · 21 Type in Section Title

If there is any interference or IR saturation, your tests will fail, not because of learning issues but because of RF setup issues. Don’t waste time, test your codes now, test RF setup later.

Learning · ™

Page 26 of the Universal Remote Control MX-900 user manual — 22 Learning
Page 26 · click to enlarge
Page 26

22 Learning

5 If the code doesn’t operate the component you can try the DoubleTap learning method. This is par- ticularly useful for components using the Philips RC5 ‘togglebit” protocol. Many high end audio companies use these codes. Just click on the 2 Time Learn radio button and you will be prompted to learn every code twice.

Universal Remote Control MX-900 — 22 Learning diagram (page 26)
Fig. 45 · 22 Learning

6 Click on SAVE - You must click on SAVE to save the LEARNED command. The blue “L” learned flag appears on the button you taught the command to.

Universal Remote Control MX-900 — 22 Learning diagram (page 26)
Fig. 46 · 22 Learning

Learning a Batch of Buttons Quickly

Using this method, MX-950 software will automatically save and select the next button, saving lots of time when you are learning an entire remote control. Key to your success are two tips:

Once you’ve prepared, batch learning goes very quickly:

1 Select the STARTING Button - Select the button that is the top left of the buttons you want to teach to. When MX-950 Editor automatically saves and selects the next button it moves left to right, unless it is learning a group of buttons with similar functions. When you are batch learning the Volume Group, MX-950 Editor first learns Volume Up, then Volume Down, then Mute, then advances to the next group.

2 Select both the LEARN and the CONTINUE button - The combination activates the batch learning capability of MXEditor. It is normal for MX-950 Editor to time out after learning the LCD page, and again after learning the hard buttons. The CONTINUE button remains selected, but you must restart the batch learning by selecting a new starting button on another LCD page or device, then selecting LEARN again.

Universal Remote Control MX-900 — 22 Learning diagram (page 26)
Fig. 47 · 22 Learning
Page 27 of the Universal Remote Control MX-900 user manual — Standalone Learning
Page 27 · click to enlarge
Page 27

3 Watch the LEARNING Window - When the info window says READY, press and hold the button on the original remote control. When it says GOOD, release the button. If it says FAIL, reteach the same command. When you see that a new button has been selected and the LEARNING window says READY, then teach the new command from the original remote control.

4 Remember to save your work, go to the File menu and select SAVE.

With some PC’s, the interconnection between the Operating System (Windows) the USB interface, the remote and the software can create learning problems with any code. If you have tried all of the tips listed on Page 20, it is worth trying Standalone Learning.

1 From the Communications Menu, select Remote Control Setup. You may have disabled the Standalone Editing feature. Make sure that the Disable checkbox is UNCHECKED.

Universal Remote Control MX-900 — Standalone Learning diagram (page 27)
Fig. 48 · Standalone Learning

Select Remote Control Setup from the Communications Menu.

Universal Remote Control MX-900 — Standalone Learning diagram (page 27)
Fig. 49 · Standalone Learning

Make sure the Disable checkbox is UNCHECKED (as shown).

Then, click on OK to close the window.

2 Download to the remote control. Now all your buttons are correctly labeled.

3 Disconnect the remote from the USB cable.

4 Press and hold both the LISTEN button and the ENTER button for five seconds. The EDIT menu will appear.

5 Select the LEARN button from the EDIT menu on the MX-950.

6 Choose between an LCD button on either the LISTEN or the WATCH pages (DEVICE BTN) or a nor- mal LCD or hard button within one of your devices (BUTTON). The top of the page now displays LEARN.

7 Navigate to the button you want to teach and select it. The top of the page now changes to READY. Teach the command you want, observing the top of the page. If it says FAIL, reteach it. If it says GOOD, then LEARN, select the next button you want and teach to it. When you are finished, simply press WATCH or LISTEN several times until the MX-950 is back in normal operating mode.

8 Now, upload to the PC and save the file.

Learning · Standalone Learning · ™

Page 28 of the Universal Remote Control MX-900 user manual — Macro Programming
Page 28 · click to enlarge
Page 28

Bullet Proof Macros or Point N Pray?

Professional Installations Require “Bullet-Proof” macros (all discrete codes or workarounds, no toggle commands). A Point and Pray macro is created when you place a toggle command in the macro (like a TV Power command). The use of Point & Pray macros that only work if the customer follows strict rules will create service calls and a lot of bad will (for example, you force the customer to verify that the system is completely off before using the TURN ON macro). When you cannot find discrete power commands, create an extra device called “POWER” or “SYSTEMPOWER” and give your client one place to find all the power commands. Instruct them to power on their system manually from this easy, convenient page, then return to WATCH or LISTEN to use the automated input switching Macros for the ACTIVITIES like Watching CABLE, Watching a DVD movie etc. - For systems with lots of tog- gle Power codes, create a “Power” HELP list.

Universal Remote Control MX-900 — Macro Programming diagram (page 28)
Fig. 50 · Macro Programming

In this example, the program- mer has created a device called SYSTEMPOWER. The client has one convenient page to power up their system manually.

Each button is labeled for the power command the program- mer has placed via the IR Database Navigator.

This is much better technique than programming a Point N Pray Macro that will result in much customer frustration.

Finding Workarounds When There Are NO Discrete Codes

By creatively experimenting you may find that you can workaround the lack of discrete codes. This takes time and there is no guarantee that you will find a workaround for any given component. Here are some common examples:

DVD and VCR Power Workaround Most DVD players will turn on when off when they receive a Play command. Thus you can workaround like this:

DVD ON = 1) Play DVD OFF = 1) Play 2) DVD Stop 2) A delay of 2 to 4 seconds 3) DVD Power (toggle command)

TV scrolling “INPUT” Workarounds Many televisions respond to a channel up or a channel number command by changing to the Antenna input regardless of what input was last selected. This creates an “anchor” action that puts the television in a known input. Thus you can create a workaround as follows:

EXAMPLE - CH Up takes TV to the ANT A input (and the TV has 5 inputs -Ant A, Ant B, EXT1, EXT2 and EXT3)

Macro Programming · Macro Programming

Page 29 of the Universal Remote Control MX-900 user manual — Using the Macro Window
Page 29 · click to enlarge
Page 29

TV to EXT3 = 1) Ch Up (takes TV to ANT A regardless of what input was last selected)

2. Input (takes TV to next input - ANT B) 3) Input (takes TV to next input - EXT 1) 4) Input (takes TV to next input - EXT 2) 5) Input (takes TV to desired input - EXT 3)

Using the Macro Window

The Macro Window controls macro recording as follows:

Record- This is the fastest way to record a macro. Select a button, click on Record, then use TREE View to navigat to the device and page of a button you want. When you click on the button, it is added to the macro as a macro step.

Save - Click to stop Macro Recording and save your work.

Delay - Click to open the delay win- dow. Any step can be a delay between .1 and 30 seconds. Longer delays can be created by using more than one delay.

Jump - As the last step in a Macro, you can specify a jump to any page of any device. You can program another jump in the macro to display a page with a status feedback message or image.

Test Macro - Play back your macro by following these steps:

Universal Remote Control MX-900 — Using the Macro Window diagram (page 29)
Fig. 51 · Using the Macro Window
1. Select the first step in the macro.
2. Connect to an MX-950

Delete - First select the step you want to delete, then click on this button (or the Delete key on the keyboard.

3. Click on the TEST button.

Import a Macro - First select the the button without a macro, then click on this button, then click on the button that has the macro you want imported.

Draggable Macro Steps - In this window, you can view all of your macro steps. You can click and drag any step to any position, changing the order of the macro.

IR Data - Click on this to open IR Database Navigator, then drag a code from the Navigator to a macro step.

Normal, Press and Hold and MX- 950 ONLY -Variable List Box - A “Normal” macro has one sequence of steps that will always playback when the button is pressed.

MX-950 Only - SET VARIABLE Opens the Set Variable window, which enables you to pick an already-created variable and set it to 0, 1 or to simply Invert its sta- tus.

Universal Remote Control MX-900 — Using the Macro Window diagram (page 29)
Fig. 52 · Using the Macro Window

A “Press and Hold” macro has two sequences, one sequence is played when the button is pressed normally. The other sequence is played when the button is pressed and held for longer than the spec- ified time.

MX-950 Only - Text - Any step can make the button label change. If you want the label to stay changed, insert a delay after the text step to keep the text on for enough time for your client to read it.

MX-950 Only - Sound - Any step can have a sound WAV file programmed by dragging a sound from the sound gallery to the macro. However, to program a second sound file in the same macro (so that there is a beep at the beginning and a “tada” at the end of a macro), you must program a delay in between the two sounds as long as the first sound or longer.

A “Variable” macro has two sequences. One sequenc e is played back when the selected variable=0, the other when the variable=1.

Macro Programming · ™

Page 30 of the Universal Remote Control MX-900 user manual — Example: Power On Macro
Page 30 · click to enlarge
Page 30

Programming a System Power On Macro

Set up your laptop and the connected remote within operational range of the home theater system while programming a macro. Macros that the client will use to turn the system on require extensive testing of delays and you can expect to do a lot of experimenting while programming.

In this example, the WATCH device’s ON button is programmed to turn on the system, configure all the Inputs and Modes for the client’s favorite activity, watching HDTV Cable TV.

1 In Tree View, navigate to the WATCH device. On the simulator, select the On button.

2 Verify that the Type list box at the bottom of the Macro Window has the default NORMAL selected.

Universal Remote Control MX-900 — Example: Power On Macro diagram (page 30)
Fig. 53 · Example: Power On Macro

3 Click on the RECORD icon or select Macro from the Program Menu.

Universal Remote Control MX-900 — Example: Power On Macro diagram (page 30)
Fig. 54 · Example: Power On Macro

4 In Tree View, expand all the pages of the devices you are going to power on. Navigate to the first device you’d like to turn on. Since the Plasma TV in the example system takes several seconds to warm up, it is the first device we’ll turn on. With single clicks on the pages inside the Plasma TV device we find the P-On command on Page 3.

5 On the simulator, click on the button with the device’s Power On command.

Universal Remote Control MX-900 — Example: Power On Macro diagram (page 30)
Fig. 55 · Example: Power On Macro

The new step appears in the Macro spread sheet:

Macro Programming

Page 31 of the Universal Remote Control MX-900 user manual — 27 Macro Programming
Page 31 · click to enlarge
Page 31

27 Macro Programming

6 Program steps to power on the other components in the system. In this example, the cable box is powered on all the time, since it is a DVR, so the only other component to power on is the surround sound receiver.

Universal Remote Control MX-900 — 27 Macro Programming diagram (page 31)
Fig. 56 · 27 Macro Programming

7 Program steps to select the correct TV and Receiver input for the client’s favorite activity. In this example the client’s favored activity is watching Cable TV. The cable box is connected to the TV input of the Surround Sound receiver and the component output of the cable box is directly con- nected to the Plasma TV’s Video 5 input.

Universal Remote Control MX-900 — 27 Macro Programming diagram (page 31)
Fig. 57 · 27 Macro Programming

8 Program a jump to the Device and Page they use for their favorite activity. Click on the JUMP icon.

Universal Remote Control MX-900 — 27 Macro Programming diagram (page 31)
Fig. 58 · 27 Macro Programming

9 Select the correct device and page from the Jump window. The jump appears in the Macro window in the column under Jump.

Universal Remote Control MX-900 — 27 Macro Programming diagram (page 31)
Fig. 59 · 27 Macro Programming

10 Now, test if delays are necessary in your macro. First, turn the TV and the Receiver to the wrong input, then turn off everything in the theater. Point the connected MX-950 at the system. Select the

first step in the list by clicking on it. Now, click on the TEST button. Observe the television and the receiver. Did they both switch to the correct input?

In the example system, the TV requires four seconds of warmup before the Input will correctly change. The surround sound receiver requires two seconds, so we program a four second delay after the TV and the Receiver power on.

™

Page 32 of the Universal Remote Control MX-900 user manual — 28 Macro Programming
Page 32 · click to enlarge
Page 32

28 Macro Programming

11 Select the Delay icon , then when the delay window opens, click on the preset amount of delay or enter any time between .1 second and 30 seconds in the “Customize” window.

Universal Remote Control MX-900 — 28 Macro Programming diagram (page 32)
Fig. 60 · 28 Macro Programming

12 The new step appears in the list. Now, drag the delay step to the correct location.

Universal Remote Control MX-900 — 28 Macro Programming diagram (page 32)
Fig. 61 · 28 Macro Programming

Each IR command lasts approximately 1/3 of a second, so if you have 3 commands, one second has elapsed.

13 Again, turn the TV and the Receiver to the wrong input, then turn off everything in the theater. Point the connected MX-950 at the system. Select the first step in the list by clicking on it. Now, click on the TEST button. Observe the television and the receiver. Did they both switch to the correct input? Continue to revise the macro with delays or changes until the macro ALWAYS correctly turns every- thing on and switches the surround sound receiver and television to the correct input. When the macro is perfect, click on the SAVE in the Macro Window.

Universal Remote Control MX-900 — 28 Macro Programming diagram (page 32)
Fig. 62 · 28 Macro Programming

14 Remember to save your work, click on SAVE in the File Menu.

Page 33 of the Universal Remote Control MX-900 user manual — 29 Type in Section Title
Page 33 · click to enlarge
Page 33

29 Type in Section Title

Programming a Power Off Macro

A Power Off macro is much simpler than a Power On macro, since there are rarely any delays to test, etc. Usually, to give the client some feedback that the macro is working, the TV is turned off first.

Universal Remote Control MX-900 — 29 Type in Section Title diagram (page 33)
Fig. 63 · 29 Type in Section Title

When you are forced to “workaround” a DVD player or VCR without a discrete off command, you will make the macro more reliable if you place the time consuming anchor (the play command) at the beginning of the macro. Make sure that you turn the DVD player off before testing this kind of workaround. You are testing the worst case, you know that a toggle type power command will turn the DVD player off, you are concerned about an event that might happen. The DVD player is already off, but the client presses the MAIN Power Off to turn everything else OFF. If you only programmed a toggle Power command, everything else would turn off, but the DVD player would turn on. This “workaround” ensures that the DVD player turns off.

Finally, so that this macro will work correctly when you set up Punch Through, program a jump to the WATCH pages. Thus if the user presses OFF after watching a DVD movie, the MX-950 will jump to the WATCH device, perfect for picking up the remote tomorrow night!

Copying or Importing Macros for Activity Macros

You can often speed programming by instantly inserting all of the steps of a previously programmed macro as the starting point of a new macro. The inserted steps are completely editable, without changing the original macro.

1 Do not start recording at the new location. Simply select the button where you would like the macro

inserted. Then click on the IMPORT button.

Universal Remote Control MX-900 — 29 Type in Section Title diagram (page 33)
Fig. 64 · 29 Type in Section Title

2 Navigate to the device and page where the original macro is programmed. Click on the button that contains the macro. All of the steps are copied/cloned into the new button location.

4 Edit as needed and click on SAVE.

You can first select the button with a Macro, select Copy from the Edit Menu, then select the button without a macro and select Paste from the Edit Menu. The keyboard shortcuts for Copy are Control|C, for Paste Control|V.

Macro Programming · ™

Page 34 of the Universal Remote Control MX-900 user manual — 30 Type in Section Title
Page 34 · click to enlarge
Page 34

30 Type in Section Title

Push and Hold Macros

By selecting this option, you now have the ability for one button to issue two different macros. One macro is issued if the button is pressed briefly, another completely different macro is issued if the button is pressed and held. Here is a way to use Push and Hold macros that we think you might find useful for power user clients.

Power users constantly switch devices and make adjustments to different components so waiting for the Activity macros to finish reconfiguring their system can be frustrating to them. By programming each of their activity macros to only issue when they press and hold the button for two seconds, you can program each but- ton to simply Jump to the device when they tap the button.

Here’s:

1 Select the button you’d like to program with two different macros.

2 Select Press-Hold Mode from the Type list box at the bottom of the Macro Window. Then, set the TIME in the Options window to 2 seconds. This ensures that the client will have to Press and Hold the button two seconds to issue the Macro.

Universal Remote Control MX-900 — 30 Type in Section Title diagram (page 34)
Fig. 65 · 30 Type in Section Title

3 Click on the Tab at the bottom of the Macro Window labeled BEFORE, then program a jump to the device only.

Universal Remote Control MX-900 — 30 Type in Section Title diagram (page 34)
Fig. 66 · 30 Type in Section Title

When the client presses the button for less than 2 seconds, only the jump occurs.

Universal Remote Control MX-900 — 30 Type in Section Title diagram (page 34)
Fig. 67 · 30 Type in Section Title

Macro Programming

Page 35 of the Universal Remote Control MX-900 user manual — 31 Macro Programming
Page 35 · click to enlarge
Page 35

31 Macro Programming

4 Click on the Tab at the bottom of the Macro Window labeled AFTER, and program the full macro (in the example shown; everything this system needs to Watch a DVD).

Universal Remote Control MX-900 — 31 Macro Programming diagram (page 35)
Fig. 68 · 31 Macro Programming

Program the simple jump to occur after a press and hold, while the Activity macros occur with a normal tap.

Variable Macros (MX-950 Only)

This is another method for one button to issue two different macros. One macro is issued when the button is pressed and a particular variable is “0”, another completely different macro is issued if the button is pressed and the same variable is now equals “1”.

Variables allow you to track when a particular button has been pressed. Then when another button is pressed, you can do something different based on the previous button press.

Clever use of variables can enable you to add all kinds of elegant improvements to operation. Here’s an exam- ple of variables, used in this case to remove the delays in the activity macros on the Watch page once the pro- jector is on.

1 The macro to turn on the system and watch Cable TV is very long in this example system. The pro- jector requires 25 seconds to warm up before the inputs can be changed.

Universal Remote Control MX-900 — 31 Macro Programming diagram (page 35)
Fig. 69 · 31 Macro Programming

™

Page 36 of the Universal Remote Control MX-900 user manual — 32 Macro Programming
Page 36 · click to enlarge
Page 36

32 Macro Programming

2 In the Type list box at the bottom of the Macro Window, select Variable as the type.

Universal Remote Control MX-900 — 32 Macro Programming diagram (page 36)
Fig. 70 · 32 Macro Programming

3 In the Variable list box that now appears, select New Variable.

Universal Remote Control MX-900 — 32 Macro Programming diagram (page 36)
Fig. 71 · 32 Macro Programming

4 In the New Variable window that opens, type in a descriptive name, then click on OK.

Universal Remote Control MX-900 — 32 Macro Programming diagram (page 36)
Fig. 72 · 32 Macro Programming

5 Verify that the new variable name appears in the Variable window as the selection.

Universal Remote Control MX-900 — 32 Macro Programming diagram (page 36)
Fig. 73 · 32 Macro Programming

6 Now your macro window displays two different tabs. One is the macro that will be sent when the projectorpower variable = 0, the other when the projector power variable = 1. Program the macro in Variable=0 with the Power On commands and the delay, while the macro in Variable=1 does not.

ProjectorPower Variable = 0 ProjectorPower Variable = 1

Universal Remote Control MX-900 — 32 Macro Programming diagram (page 36)
Fig. 74 · 32 Macro Programming
Universal Remote Control MX-900 — 32 Macro Programming diagram (page 36)
Fig. 75 · 32 Macro Programming
Page 37 of the Universal Remote Control MX-900 user manual — 33 Macro Programming
Page 37 · click to enlarge
Page 37

33 Macro Programming

Now, you must program all macros that the client might use to turn on the system with a variable change that changes the variable ProjectorPower to “1”. Thus no matter what button you use to turn on the system, the MX-950 will know the true status of the projector is on. Likewise all macros that turn the system off must change the variable ProjectorPower to “0”.

7 In all macros that power on the projector, repeat steps 1-7, then add a new step to all the macros. Click on the Set Variable button on the macro toolbar.

Universal Remote Control MX-900 — 33 Macro Programming diagram (page 37)
Fig. 76 · 33 Macro Programming

8 The Set Variable window opens. Select the ProjectorPower variable and set it to a state of 1 (indicat- ing that the projector is now powered on). Afterwards, the new step appears in the macro list.

Universal Remote Control MX-900 — 33 Macro Programming diagram (page 37)
Fig. 77 · 33 Macro Programming

9 In all macros that power OFF the projector add a new step to the macros. Click on the Set Variable button and set the Projector Power variable to equal “0” after the projector is off.

Universal Remote Control MX-900 — 33 Macro Programming diagram (page 37)
Fig. 78 · 33 Macro Programming

™

Page 38 of the Universal Remote Control MX-900 user manual — Using Sounds (MX-950 Only)
Page 38 · click to enlarge
Page 38

Using Sounds (MX-950 Only)

Setting the Default Sound MX-950 Editor enables any button to have a sound play when the button is pressed. You can set a default sound for every button throughout the configuration as follows:

1 From the File menu select User Preferences. The User Preference window will open.

2 Select one of the three options:

None - Your buttons will only make sounds if you drag a sound from the sound gallery to a button. Default Beep - Whenever a button that has an IR command or macro is pressed, the MX-950 will beep. User Defined - You browse to a file location and select a wav file that will play whenver an active but-

ton is pressed.

Using the Sound Gallery MX-950 Editor enables you to program any button with as many sounds as you like. However, for each sound, you must program a delay after the sound, long enough for the sound to play completely. To use sounds, click on the Sounds icon in the macro toolbar, or select Sound Gallery from the Tools Menu. Simply drag a sound into a macro, then place the optimum delay after each sound.

Universal Remote Control MX-900 — Using Sounds (MX-950 Only) diagram (page 38)
Fig. 79 · Using Sounds (MX-950 Only)

In this example four sounds play back when the button is pressed. For each sound to play, a delay must be placed after it.

Using the Image Gallery (MX-950 Only)

The MX-950 has a limited ability to use images instead of text. First, make sure you are in Simulator and Page View mode, then double click on the page you want to place an image as a button label. Double clicking opens a new Page View and sets the Simulator to the same page. Now, from the tools menu, open the Image gallery. Drag an image from the gallery to the Simulator View. Simulator View distorts the size of the image, but allows you to drag the image to any position on the page. Page View gives you a much better idea of what the image will look like, but does NOT allow you to drag or delete the image. By using both views side by side, you control the image position in Simulate View, but judge it’s position in Page View.

Universal Remote Control MX-900 — Using Sounds (MX-950 Only) diagram (page 38)
Fig. 80 · Using Sounds (MX-950 Only)

You can import bmp or jpg images to the gallery, however, they cannot be larg- er than 64 pixels by 88 pixels. They can be four color (black, white, light grey and dark grey).

By using both Simulator and Page views side by side, you control the image position in Simulate View, but judge it’s position in Page View.

Sounds and Images

Page 39 of the Universal Remote Control MX-900 user manual — Programming Punch Through
Page 39 · click to enlarge
Page 39

Punch Through allows you to set the same functions on all devices very quickly. You can punch through any of the groups of buttons on the MX-950. In this exampe, the Power On and Power Off buttons on every page and every device are set to punch through to the WATCH Power On and Power Off buttons, thus the user can power off the system without returning to WATCH to press Power Off. Likewise, the Volume Up, Down and Mute have been set as a group to punch through to the surround sound receiver. After programming, flags remind the programmer that the buttons have been set to punch through.

1 Open the Punch Through window by clicking on the shortcut button in the toolbar or by selecting Punch Through from the Program Menu.

2 Select the devices which you want to change programming by clicking on them while holding down the CONTROL key on the keyboard. If you want them all selected (normal for Volume Up, Down and Mute), simply click on the Select All button. Any device you select will be HIGHLIGHTED in the “Punch To” list.

Universal Remote Control MX-900 — Programming Punch Through diagram (page 39)
Fig. 81 · Programming Punch Through

3 Select the device that has the codes you want used in the Punch From list.

4 Click on SAVE. Check the devices you programmed, you should see the red PT (Punch Through) flag on every button affected on all the devices you programmed:

Punch Through · Programming Punch Through · ™

Page 40 of the Universal Remote Control MX-900 user manual — Programming RF Control Options
Page 40 · click to enlarge
Page 40

Programming RF Control Options

The RF Setup Window The RF Setup window opens after selecting RFControl from the Program Menu or clicking on the shortcut button.

Universal Remote Control MX-900 — Programming RF Control Options diagram (page 40)
Fig. 82 · Programming RF Control Options

Adjusting Signal and IR Output Options

The RF Setup window enables you to adjust the properties of RF Control by clicking on the intersection of a row and a column and then selecting from the pull down list box the property you want. All of your devices are displayed. You can set each device individually to be controlled by clicking on the cell you want to change. After clicking, a list box of options will appear.

SIGNAL controls how the MX-950 will send commands:

Universal Remote Control MX-900 — Programming RF Control Options diagram (page 40)
Fig. 83 · Programming RF Control Options

IR and RF - Both RF signals and IR com-

mands are sent from the MX950. The RF signals will also be issued as IR commands by the MRF-300. IR - Only IR commands are sent from

the MX950, as a result the MRF- 300 does not send any com- mands. RF - Only RF signals are sent from the

MX950, as a result only IR com- mands from the MRF-300 are received by the device.

Universal Remote Control MX-900 — Programming RF Control Options diagram (page 40)
Fig. 84 · Programming RF Control Options

RECEIVER enables you to select which MRF-300 receiver will receive the commands for this device. Thus, you can send commands to a device in another location via a second MRF- 300 placed in that location (up to 16 in one house).

Universal Remote Control MX-900 — Programming RF Control Options diagram (page 40)
Fig. 85 · Programming RF Control Options

RF Control

Page 41 of the Universal Remote Control MX-900 user manual — Programming RF Control Options
Page 41 · click to enlarge
Page 41
Universal Remote Control MX-900 — Programming RF Control Options diagram (page 41)
Fig. 86 · Programming RF Control Options

IR OUTPUT controls the Line Outputs for Flashers affixed to the front panels of compo- nents. You can opt to either send IR Commands to:

ALL - The commands are sent to all of

the Flashers 1-6 - Just the specified Flasher receives the IR commands (Useful when identical TV’s or VCR’s are utilized in the system)

Adding RF Base Stations, Conguring ID#’s and Front Blasters

To add a new receiver to the list, to change the Receiver ID# of your existing receiver or to enable/disable the Front Blaster, click on the Receiver button of the RF Control window.

Universal Remote Control MX-900 — Programming RF Control Options diagram (page 41)
Fig. 87 · Programming RF Control Options

After pressing the Receivers button, the RF Control Window will enlarge revealing the Receiver configuration options. Again, you click on a cell to adjust.

The Receiver ID cells enable you to change the ID# of each receiver, so that commands for one will be ignored by the other if set to different ID’s.

If you want the Front Blaster turned OFF on any receiver, reset it by clicking on the cor- rect CELL and selecting OFF.

You may rename a receiver to something more descriptive by first selecting the receiver’s name cell, then clicking on the Rename button.

Universal Remote Control MX-900 — Programming RF Control Options diagram (page 41)
Fig. 88 · Programming RF Control Options

RF Control · ™

Page 42 of the Universal Remote Control MX-900 user manual — Enable or Disable Standalone...
Page 42 · click to enlarge
Page 42

Enable or Disable Standalone Editing

Enable or Disable Standalone Editing

You can disable the Edit menu of the MX-950. This is the menu that appears when you press and hold LISTEN and ENTER for five seconds. Though the ability to change the labels and to learn codes standalone is useful to some installers, you may want to prevent your customer from accessing these settings.

1 Open the Remote Control Setup window by selecting it from the Communications Menu.

Universal Remote Control MX-900 — Enable or Disable Standalone... diagram (page 42)
Fig. 89 · Enable or Disable Standalone...

2 Check the Disable checkbox if you want to prevent anyone from accessing the Edit menu on the MX-950. Click on OK when you’ve made your changes.

Universal Remote Control MX-900 — Enable or Disable Standalone... diagram (page 42)
Fig. 90 · Enable or Disable Standalone...

The Settings menu appears when WATCH and Enter are pressed and held for five seconds.

Page 43 of the Universal Remote Control MX-900 user manual — Downloading
Page 43 · click to enlarge
Page 43

You download to the remote control by:

1 Make sure the remote control has charged batteries.

2 Connect the cable between the PC and the remote control.

3 Verify that the file you have open in MX-950 Editor is the one you want to download to the remote

control.

4 Click on the Download to Remote Control shortcut button on the toolbar or choose Download from the Communications Menu. Do not move the mouse or touch the keyboard during the download.

Using the Setup Menu

1 Press and Hold both the WATCH and the ENTER button for five seconds.

2 Once the Setup menu appears, you can browse between it’s two pages via the PAGE buttons. It will automatically time out, or you can press the WATCH or the LISTEN button to exit.

TIME (MX-950 Only) - Set the clock here, however if you want to change whether it is dis-

played or not, go to INDICATOR on page 2 of the Setup Menu. BACKLIGHT (MX-950 and TX-1000 Only)- Configure the amount of time that the MX-950 will stay lit after it is picked up. DISPLAY - You can adjust the brightness and contrast of the display. Keep the setting of color set to S/W, thus all your changes of device backlighting color will be displayed. SOUND/BEEP - You can adjust the Volume of the MX-950 speaker. Note that TX-1000 and MX-

900 editor offer BEEP volume to set the volume of the Beeps. If your client prefers silent operation, simply set the volume to 0. PICKUP (MX-950 Only) - You can disable the Pick Up Sensor INDICATOR (MX-950 Only) - You can disable the display of the Clock, the IR and the Battery Indicator here.

Finishing the Program · Downloading · ™

Page 44 of the Universal Remote Control MX-900 user manual — Downloading
Page 44 · click to enlarge
Page 44

Universal Remote Control BY ®

500 Mamaroneck Avenue Harrison, NY 10528 Phone: (914) 835-4484

Fax(914) 835-4532 www.universalremote.com

™

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Universal Remote Control MX-900

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Universal Remote Control MX-900

Be the first to ask — other owners or our team will answer.

Original document

Universal Remote Control MX-900 manual PDF

44 pages·1.9 MB·Universal Remote·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…