Instruction/ maintenance manual of the product 1050patton Patton electronic
Go to page of 9
USER MANUAL MODEL 1050 AC Powered, Asynchronous Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part #07M1050-B Doc.
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1050 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
4.0 INSTALLATION The Model 1050 is easy to install. After configuring the unit properly , you will need to connect the two twisted pairs and the RS-232 cable. Figure 2 (below) shows the rear panel location of the RJ-1 1 jack and strain relief grommet (line connections), as well as the female DB- 25 (RS-232 connection).
4.1.2 TWISTED P AIR CONNECTION USING RJ-1 1 If your two-pair cable is terminated in an RJ-1 1 plug, you may use the RJ-1 1 jack in the back of the Model 1050 to make the connection. The RJ-1 1 jack on a Model 1050 series Short Range Modem is prewired for a standard TELCO wiring environment.
4.2.2 ST AR T OPOLOGY Using a star topology , you may connect several Model 1050s together in a master/slave arrangement. Maximum distance between the units will vary based upon the number of drops, data rate, wire gauge, etc. Call Patton T echnical Support for specific distance estimates.
5.2.2 REMOTE ANALOG LOOP The second test mode is Remote Analog Loop. T o enter this mode, set one of the Model 1050s (local) in test mode by depressing the "Loopback T est" switch. Any characters sent from the remote 1050 will be returned to it (see Figure 5).
APPENDIX B P A TTON MODEL 1050 CABLE RECOMMENDA TIONS All Patton Electronics Company Short Range Modems are tested to the distances published in our Catalogs and Specification Sheets on twisted-pair cable with the following characteristics: W ire Gauge Capacitance Resistance 19 A WG(.
APPENDIX D P A TTON MODEL 1050 BLOCK DIAGRAM Copyright © 1997 Patton Electronics Company All Rights Reserved Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business. I trust that you find this user manual helpful.
An important point after buying a device Patton electronic 1050patton (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1050patton yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1050patton - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1050patton you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1050patton will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1050patton, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1050patton.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1050patton. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1050patton along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
