Instruction/ maintenance manual of the product AJ65BT-D75P2-U-HE Mitsubishi Electronics
Go to page of 24
User ’ s Manual (Hardware) AJ65BT -D75P2-S3 Thank you fo r purchasing the Mitsubishi general- purpose programmable logic contro ller MELSEC- A series. © 201 1 MITSUBISHI ELECTRIC CORP ORA TION AJ65BT -D75P2-S3 Positioning Module Prior to use, pleas e read t his and r elevant manuals t horougly t o fully understand the product.
A-1 SAFETY PRECAUTIONS (Read these precautions before using.) When using Mitsubishi equipment , thoroughly read thi s manual and the associated manuals introduced in the manual. Also pay careful atten tion to safety and handle the module properly . These precautions apply only to Mitsubish i equipment.
A-2 [Design Precautions] [Design Precaution] [Installation Precautions] W ARNING ● When data lin k becomes faulty , the operation of communication f aulty station vary depending on its dat a link type.
A-3 [Wiring/Connection Precautions] CAUTION ● Be sure to shut o ff all phases of t he external power supply used by the system before in stallation or wiring. Not doing so can cause the product to be damaged or malf unction. ● Be sure to ground the FG terminal to the class-D (class-3) or higher grounding.
A-4 [Wiring/Connection Precautions] [St artu p and Maintenance Precautions] [Disposal Precautions] CAUTION ● When disconnecting the co mmunication and power supply cables from the module, do not hold and pull the cable p art. Disconnect the cab les after loosening the screws in the portions connected to the module.
A-5.
A-6.
A-7.
A-8 CONDITIONS OF USE FOR THE PRODUCT (1) Mitsubishi progr ammable controller ("th e PRODUCT") shall be u sed in conditions; i) where any proble m, fault or failure occurring i n the PRODUCT.
A-9 Notwithstandi ng the above, restrictions Mitsubish i may in its so le discretion, authorize use of the PRODUCT in one or more of the Prohibite d Applications, provided t hat the usage of the PRODU.
A-10 ABOUT THE MANUALS The following product are available fo r this equipment. Refer to the tab le given below to choose suit able manuals. COMPLIANCE WITH THE EMC AND LOW VOL T AGE DIRECTIVES 1) Met.
A-11 CONTENTS 1. OVERVIE W ........... ........... .......... .......... ........... .......... ........... ............. ........... .. 1 2. PERFORM ANCE SPE CIFICATIONS ...................... .......... ........... ............. ..... 1 3. NAME O F EACH PART .
1 1. OVERVIEW This manual describes how to insta ll AJ65BT -D75P2-S3 Positioning Module (hereaft er abbreviated as D75P2) and how to wire them with external devices. After u npacking D75P2, please con firm that the f ollowing product s are contained. 2.
2 3. NAME OF EACH P A RT No. Name Description 1) Corresponding ax is LED display Indicates the axis for t he "8)17 segm ent LED" message. 2) CC-Link st atus LED displ ay Shows the powe r supply and d ata communication conditions. 3) Transmission speed setting switch Sets the data co mmunication sp eed.
3 *1 For modules of the hardware version L o r later , the display pa rt is changed to a LED module. (The display content s remain the same as the 17-segment LED.
4 4. LOADING AND INST ALLA TION The following is explanations of the handling precautions and installation en vironment which is common to modules when handling D75P2 from unpacki ng to installation. For the details of loading and installation of the module, refer to User's Manual of programmable controll er CPU module to be used.
5 5. WIRING DA T A-LINK CA BLES This section describes the method for wiring a twisted cable between the D75P2 and master module. 5.1 Precautionary items when handling twisted cables Do not handle t he twisted cables in t he following manner . These extreme activities will damage the cables.
6 6. EXTERNAL WIRING Precautionary notes when wiring as well as the I/ O interface are described below . 6.1 Precautionary notes when wiring This section d escribes the pr ecauti onary notes for the wiring process between the D75P2 and out side (drive unit).
7 6.2 I/O Interface : Wiring re quired, : Wiring performed as required I/O classification External wiring Pin number Internal circuit Signal name Wiring requirement Input 11 Near-point signal DOG 12 H.
8 *1 Select open collector output or different ial output, according to the drive unit used. Remarks The following shows the rela tionship between the pulse output mode selected via the parameter and the pulse output according to "positive logic/negative logic selecti on.
9 * T o construct an absolute position detection syst em, perform wiring as shown below: Remarks *2 Signals in the ABS transfer mode are shown. *3 Signals in the normal state (not in the ABS transfer mode ) are shown. For details, refer to t he specification/instruction manual for the servo amplifier used.
10 7. EXTERNAL DIMENSIONS Unit:mm (inch) 170 71 80 161 2- 4.5 installation hole 9.5 63.5.
11 MEMO.
Country/Region Sales office/Tel Specifications subject to change without notice. Country/Region Sales office/Tel U.S.A Mitsubishi Electric Automation Inc. 500 Corporate Woods Parkway V ernon Hills, IL 60061, U.S.A. T el : +1-847-478-2100 Brazil MELCO-TEC Rep.
An important point after buying a device Mitsubishi Electronics AJ65BT-D75P2-U-HE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mitsubishi Electronics AJ65BT-D75P2-U-HE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mitsubishi Electronics AJ65BT-D75P2-U-HE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mitsubishi Electronics AJ65BT-D75P2-U-HE you will learn all the available features of the product, as well as information on its operation. The information that you get Mitsubishi Electronics AJ65BT-D75P2-U-HE will certainly help you make a decision on the purchase.
If you already are a holder of Mitsubishi Electronics AJ65BT-D75P2-U-HE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mitsubishi Electronics AJ65BT-D75P2-U-HE.
However, one of the most important roles played by the user manual is to help in solving problems with Mitsubishi Electronics AJ65BT-D75P2-U-HE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mitsubishi Electronics AJ65BT-D75P2-U-HE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
