Instruction/ maintenance manual of the product IT4410 Hand Held Products
Go to page of 32
™ Quick Check 2D Print Quality Assessment Applies to the following products: IT4410, IT4710, IT4600, IT4800, IT4X80 User’s Guide.
Disclaimer Hand Held Products, Inc. d/b/a HHP (“HHP”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all ca ses consult HHP to determine whether any such changes have been made.
i Chapter 1 - Introduction User Operation ...................................................................... 1-1 Reading Techniques.............................................................. 1-1 Symbology/Parameter Specifics ...................
ii Symbology .................................................................... 1-19 Useful Row Height ....................................................... 1-19 X-dimension ................................................................. 1-20 Chapter 2 - Quick*View Quick*View Demonstration Software Instructions .
1 - 1 1 Introduction Two-dimensional Print Quality Assessment (2D PQA), a feature of HHP's image readers, identifies a successfully read symbol and also reports graded mea- surement parameters obtained from the symbol.
1 - 2 • The hand-held imager has a view finder that projects a bright aiming beam that corresponds to the imager’s horiz ontal field of view. The aiming beam should be centered over the bar code and positioned horizontally over the code (no tilt, skew, or rotation).
1 - 3 2D PQA Reporting Full Report HHP's 2D PQA reporting can be enabled in two different modes: Full Report or Screening. If you are using Quick*View, you can enable Full Report, a listing of al.
1 - 4 If your imager is in keyboard wedge mode, enable Screening by scanning the following bar codes. You can exit both Full Report and Scr eening modes by either typing the menu command, 2D_PQA0, if .
1 - 5 While the details are explained belo w, this general format includes: • the encoded data (the usual ou tput message) in the first line. • a banner " >>> PQA from HHP <<<" id entifying the start of the 2D PQA report.
1 - 6 {5} [A] < Row Height = 3.1 X {6} [A] < Useful Row Height = 2.5 X (82% Row) {7} [A] < Data Safety Margin = 100% (0 Erasures & 0 Errors) {8} [B] < Edge Accuracy = 59% {9} [C] < Print Growth = -43% of X where: {1} is always the Encoded Message, the usual data output.
1 - 7 D if Useful Height >= 1.0 X, else Fo t h e r w i s e In Screening modes, this parameter is reported as "Useful Row Height is Too Short (1.5X)" when that is the case. {7} lists the Data Safety Margin , which is the ratio of the unused error correc- tion words to the recommend ed (!) number of such wo rds.
1 - 8 In rare instances where neither a valid Start nor Stop pattern is measurable, yet the symbol is somehow read, lines {8} a nd {9} are replaced by a message to that effect. The message is either: "[F] < Start/Stop Decode Fails" in a Full Report or "Start/Stop Characters are Bad" in a Screening mode.
1 - 9 A if Row Height >= 1.5 X, Fo t h e r w i s e . {6} lists the Data Safety Margin . Because MicroPDF's er ror correction level is fixed, this parameter is just the "Unused Error Correction" and always between 0 and 100%. {7} lists the Edge Accuracy measured in multiple scans through the Row Address Patterns.
1 - 10 Note: The reported X-dimension is appro ximate and based upon use of the IT4410LR at 4.7 in (12 cm) (see "Re ading Techniques" on page 1-1). If you use different image engines, the X-dimension will vary. If you hold the reader closer than 4.
1 - 11 {7} [A] < Data Saf ety Margin = 100% {8} [A] < Horizontal Pri nt Growth = +10% of X {9} [A] < Vertical Print Growth = +12% of X {1} is the Encoded Message . {2} is the Banner heading. {3} identifies the Symbology (DATA MATRIX) and lists the symbol's ECC and size.
1 - 12 {3} QR CODE: Model 2 Vers ion 3 (29 x 29 modules) {4} Mask Pattern Reference #3, Error Correction Level "M" {5} Data Field: 44 data & 26 che cks in 1 block(s) of GF(256) {6} X roughly = 0.
1 - 13 {4} X roughly = 0.043" {5} [A] < Data Saf ety Margin = 100% {6} [A] < Horizontal Pri nt Growth = +2% of X {7} [A] < Vertical Print Growth = -1% of X {1} is the Encoded Message . {2} is the Banner heading. {3} identifies the Symbology (MAXICODE) and lists the symbol's Mode.
1 - 14 {7} [A] (Ok) < Bar Widths = 0.022 in. {8} [A] (Ok) < Inte r-Bar Gaps = 0.023 in. {1} is the Encoded Message . {2} is the Banner heading. {3} identifies the Symbology , (POSTNET or PLANET Code), and lists also the symbol's size and allowed range of measured width.
1 - 15 4-S tate Codes The Full Report from a typical scan look s like the following (line numbers have been added in curly brackets): {1} B15AJ6T {2} >>> PQA from HHP <<< {3} 4-STATE(British): 34 Bars, nominally from 38.5 to 42.3 mm.
1 - 16 Note: For the Canadian and Australian 4-State symbologies only, any bar error that has invoked their error co rrection triggers an additional PQA parameter line: "[F] < One or more Bars are in Error!" in a Full Report or "One or more Bars are in Error!" in a Screening mode.
1 - 17 Bar Sequence Bar Sequence is the bar hei ght pattern within a height modulated, multi-state, postal-type symbology. In a 2-state symbol, a "1" represents a tall or full height bar and a "0" represents a shor t or half height bar.
1 - 18 Encoded Message The encoded message is the information (alpha, numeric, and/or control char- acters) or message contained within the bar code symbol and output as part of the decoding process. Th is information precedes th e calculated PQA parame- ters.
1 - 19 Module Errors Module Errors are individual errors with in fixed pattern/data areas. Although often benign, Module Errors in the fixed regions of a symbol can signal a fault that, in some instances, will prevent pr oper decoding.
1 - 20 height, giving more leeway to symbols printed with above minimum row heights (e.g., 4.0 X). A poor grade here is correc ted by either stretc hing the symbol ver- tically or correcting the print conditio n (e.g., turning down the thermal burn set- ting or adjusting inking) that causes rows to interfere.
2 - 1 2 Quick*View Quick*V iew Demonstration Software Instructions Quick*View is a Microsoft Windows ® program that displays decoded symbol messages and captures images (for inst ance, ID photographs) from the imager. Bar code information and images are displayed in the Quick*View window.
2 - 2 8. Double click on the Quickview.exe file. Follow the screen prompts to install the Quick*View program. 9. To start Quick*View, from the Start Menu click on Programs , Quick*View , Quick*View . Note: If you wish, you can create a shortc ut to the Quick*View executable on your desktop.
2 - 3 Using the Quick*V iew Software Upon startup, the Quick*View splash screen appears for approximately three seconds. Quick*View will then attemp t to establish communications with the Imager.
2 - 4 Scan Data W indow Once successful communication has been established, you c an scan codes and display the bar code data in a window. Select View - Scan Data Window .
3 - 1 3 Customer Suppor t Obtaining Factory Service HHP provides service for all its products through service centers throughout the world. To obtain warranty or non-warr anty service, return the unit to HHP (postage paid) with a copy of the dated purchase record atta ched.
3 - 2 T echnical Assistance If you need assistance installing or tro ubleshooting your imager, please call your Distributor or the nearest HHP technical support office: North America/Canada: Telephone: (315) 685-2476, Option 4 (8 a.m. to 6 p.m. EST) or in the U.
.
QC2DPQA-UG Rev B.
An important point after buying a device Hand Held Products IT4410 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hand Held Products IT4410 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hand Held Products IT4410 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hand Held Products IT4410 you will learn all the available features of the product, as well as information on its operation. The information that you get Hand Held Products IT4410 will certainly help you make a decision on the purchase.
If you already are a holder of Hand Held Products IT4410, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hand Held Products IT4410.
However, one of the most important roles played by the user manual is to help in solving problems with Hand Held Products IT4410. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hand Held Products IT4410 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
