
Attaching 1 Insert the left side of the front panel into the main unit. Align the groove on the front panel with the projections on the main unit. 2 Push the right side of the front panel until it locks firmly into the main unit.
Never Attempt the Following Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.
Installation Location Make sure this unit will not be installed in a location subjected to:
Radio
Presetting Stations Automatically
CAUTION
MP3/*WMA/CD Receiver CDE-110/CDE-110C CDE-110E/CDE-110UB
Alpine accepts no responsibility for lost data, etc., even if data, etc. is lost while using this product.
1 Press BAND/ / repeatedly until the desired radio band is displayed. 2 Press and hold A.ME for at least 2 seconds. The frequency on the display continues to change while the automatic memory is in progress. The tuner will automatically seek and store 6 strong stations in the selected band. They will be stored into preset buttons 1 to 6 in order of signal strength.
*CDE-110UB does not support WMA
WARNING
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS. Doing so may result in personal injury or damage to the product.
Correct Handling Do not drop the disc while handling. Hold the disc so you will not leave fingerprints on the surface. Do not affix tape, paper, or gummed labels to the disc. Do not write on the disc.
Do not leave the disc in the car or the unit for a long time. Never expose the disc to direct sunlight. Heat and humidity may damage the CD and you may not be able to play it again.
CAUTION
This symbol means important instructions. Failure to heed them can result in serious injury or death.
This symbol means important instructions. Failure to heed them can result in injury or material property damage.
VIEW
Preset buttons (1 through 6)
Inserting Discs Your player accepts only one disc at a time for playback. Do not attempt to load more than one disc. Make sure the label side is facing up when you insert the disc. Playing a disc while driving on a very bumpy road may result in skips, but this will not scratch the disc or damage the player.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing.
About media that can be played Use only compact discs with the label side showing the CD logo marks below.
Listening to Radio
1 Press BAND/ / repeatedly until the desired band is displayed. 2 Press any one of the station preset buttons (1 through 6) that has your desired radio station in memory. The display shows the band, preset number and frequency of the station selected.
1 Press SOURCE/ to select RADIO mode. 2 Press BAND/ / repeatedly until the desired radio band is displayed.
New Discs To prevent the CD from jamming, the LCD is displayed as error if discs with irregular surfaces are inserted or if discs are inserted incorrectly. When a new disc is ejected immediately after initial loading, use your finger to feel around the inside of the centre hole and outside edge of the disc. If you feel any small bumps or irregularities, this could inhibit proper loading of the disc. To remove the bumps, rub the inside edge of the hole and outside edge of the disc with a ballpoint pen or other such instrument, then insert the disc again.
Turn the Rotary encoder until the desired sound is obtained. Adjusting Volume : 0 ~ 40
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISES WHILE DRIVING. Excessive volume levels that obscure sounds such as emergency vehicle sirens or road warning signals (train crossings, etc.) can be dangerous and may result in an accident. LISTENING AT LOUD VOLUME LEVELS IN A CAR MAY ALSO CAUSE HEARING DAMAGE.
Product Cleaning Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic.
Disc Cleaning Fingerprints, dust, or soil on the surface of the disc could cause the CD player to skip. For routine cleaning, wipe the playing surface with a clean, soft cloth from the centre of the disc to the outer edge. If the surface is heavily soiled, dampen a clean, soft cloth in a solution of mild neutral detergent before cleaning the disc.
FM1 FM2 FM3 AM FM1 3 Press or to tune in the desired station. Press and hold or for at least 0.5 seconds to seek station.
If you use unspecified compact discs, correct performance cannot be guaranteed. You can play CD-Rs (CD-Recordables)/CD-RWs (CD- ReWritables) which have been recorded only on audio devices. You can also play CD-Rs/CD-RWs containing MP3/WMA formatted audio files.
Turning Power On and Off
1 Press and hold VIEW for at least 2 seconds. The hour indication will blink. 2 Press or to adjust the hours while the time indication is blinking. 3 When the hour has been adjusted, press VIEW. The Minute indication will blink. 4 Press or to adjust the minutes while the time indication is blinking. 5 When the minute has been adjusted, press VIEW. The setting time mode is completed.
Temperature Be sure the temperature inside the vehicle is between +55°C (+131°F) and –10°C (+14°F) before turning your unit on.
Press SOURCE/ to turn on the unit.
MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the driver from looking ahead of the vehicle and cause an accident.
Press and hold SOURCE/ for at least 2 seconds to turn off the unit.
1 Select the radio band and tune in a desired radio station you wish to store in the preset memory. 2 Press and hold, for at least 2 seconds, any one of the preset buttons (1 through 6) into which you wish to store the station. The selected station is stored. The display shows the band, preset number and station frequency memorized.
Moisture Condensation You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
Change SOURCE to something other than USB, then remove the USB device to prevent possible damage to its memory.
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock.
555 Rasa Tower 1, Unit 2601-2602, 26th Floor, Phaholyothin Road, Chatuchak, Chatuchak, Bangkok 10900, Thailand
ALPINE ELECTRONICS OF ASIA PACIFIC CO.,LTD.
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
ALPINE ITALIA S.p.A.
Disc Accessories There are various accessories available on the market for protecting the disc surface and improving sound quality. However, most of them will influence the thickness and/or diameter of the disc. Using such accessories can cause the disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players.
161-165 Princes Highway, Hallam
Viale C. Colombo 8, 20090 Trezzano
Phone 02-937-0505 www.alpine-asia.com
Sul Naviglio (MI), Italy
Irregular Shaped Discs Be sure to use round shape discs only for this unit and never use any special shape discs. Use of special shape discs may cause damage to the mechanism.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
Damaged Disc Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.
Detaching 1 Turn off the unit power. 2 Press (Release) at the upper right side until the front panel pops out. 3 Grasp the right side of the front panel and pull it out.
ALPINE ELECTRONICS MARKETING, INC.
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Wilhelm-Wagenfeld-Str. 1-3, 80807 München, Germany
Portal de Gamarra 36, Pabellón, 32
Phone 089-32 42 640
01013 Vitoria (Alava)-APDO 133, Spain
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately.
Maintenance If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
Controllable with Remote Control
ALPINE ELECTRONICS OF U.K. LTD.
This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote-control sensor.
ALPINE ELECTRONICS OF AMERICA, INC.
ALPINE ELECTRONICS (BENELUX) GmbH
19145 Gramercy Place, Torrance,
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock.
Fletchamstead Highway, Coventry CV4 9TW, U.K.
Transparent Sheet Disc Stabilizer
California 90501, U.S.A.
Phone 0870-33 33 763
ALPINE ELECTRONICS FRANCE S.A.R.L.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up inside and may result in fire.
ALPINE ELECTRONICS OF CANADA, INC.
777 Supertest Road, Toronto,
Ontario M3J 2M9, Canada
98, Rue de la Belle Etoile, Z.I. Paris Nord Il,
B.P. 50016, 95945 Roissy Charles de Gaulle
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire, electric shock or other injury.
may result in malfunction.
3 Press or to select the desired track (file).
Supported playback sampling rates and bit rates
Other Functions
Displaying Time
Returning to the beginning of the current track (file):
About MP3/WMA
Equalizer Presets (Factory’s EQ)
Files are played back in the order that the writing software writes them to the disc. Therefore, the playback order may not be what is expected. Verify the writing order in the software’s documentation. The playback order of the folders and files is as follows.
Press .
Press VIEW repeatedly until the time is displayed. Each press changes the display. For details, see “Displaying the Text”.
Fast backward:
Press 4(M.I.X.) in the play mode. The “ M.I.X.” indicator lights up, and the tracks (files) on the disc will be played back in random sequence.
16 kHz, 12 kHz, 11.025 kHz, 8 kHz Bit rates 8 - 320 kbps
6 typical equalizer settings are preset at the factory for a variety of musical source material.
SOURCE/
Press and hold .
Except for private use, duplicating audio data (including MP3/WMA data) or distributing, transferring, or copying it, whether for free or for a fee, without permission of the copyright holder is strictly prohibited by the Copyright Act and by international treaty.
BAND/ /
Advancing to the beginning of the next track (file):
Press SOUND repeatedly until the desired Factory’s EQ type is displayed. With each press of the button, the equalizer mode will display the selected equalizer characteristic.
Press .
Press 4(M.I.X.) again to cancel.
Fast forward:
Press and hold . 4 To pause playback, press BAND/ /. Pressing BAND/ / again will resume playback. 5 To eject the disc, press .
This device may not play back correctly depending on sampling rates.
Press and hold 4(M.I.X.) for at least 2 seconds. The “ FOLDER” and “ M.I.X.” indicators appear in the display, and all files in the current folder are played back in random sequence.
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a compression standard prescribed by the ISO, the International Standardization Organization and MPEG which is a joint activity institution of the IEC.
VIEW
3(SCROLL)
4(M.I.X.)
6(RPT)
This device supports ID3 tag and WMA tag. If tag data is in an MP3/WMA file, this device can display the title (track title), artist name, and album name ID3 tag/WMA tag data.
Connect a portable music player, etc. by simply connecting it to the input on the front panel. An optional adapter cable is required (standard RCA to 3.5ø mini-phono plug or 3.5ø to 3.5ø mini phono plug).
MP3 files contain compressed audio data. MP3 encoding is capable of compressing audio data at extremely high ratios, reducing the size of music files to as much as one-tenth their original size. This is achieved while still maintaining near CD quality. The MP3 format realises such high compression ratios by eliminating the sounds that are either inaudible to the human ear or masked by other sounds.
Adjusting Bass Level/Treble Level/ Balance (Between Left and Right)/Fader (Between Front and Rear)
Press and hold 4(M.I.X.) again to cancel.
Press SOURCE/ , and select the AUX mode to listen to the portable device.
This device can only display up to 64 characters. (Unicoded file and folder names are up to 32 characters.) For non-supported characters and symbols an asterisk is displayed. If information contains characters other than ID3 tag information, the audio file may not be played back. The tag information may not be correctly displayed, depending on the contents.
Scanning Programs
Playback
RADIO CD * 1 USB * 2 AUX RADIO
1 Press Rotary encoder (AUDIO) repeatedly to choose the desired mode.
Text information, such as the disc name and the track name, will be displayed if playing a CD text compatible disc. It is also possible to display the folder name, the file name and the tag, etc., while playing MP3/WMA files.
Press 5(SCAN) to activate the scan mode. The first 10 seconds of each track (file) will be played back in succession.
* 1 Displayed only when a disc has been inserted. * 2 Displayed only when USB memory is connected.
1 Insert a disc with the label side facing up. The disc will be pulled into the unit automatically, and the “ DISC IN” indicator lights up .
WMA, or “Windows Media™ Audio,” is compressed audio data. WMA is similar to MP3 audio data and can achieve CD quality sound with small file sizes.
Each press changes the mode as follows:
Press 5(SCAN) again to cancel.
Portable player, etc. Main unit
MP3/WMA Play Display The folder number and file number will be displayed as described below.
MP3/WMA files are prepared, then written to a CD-R or CD-RW using CD-R writing software. A disc can hold up to 255 files/folders (including Root Folders), and the maximum number of folders is 255. Playback may not be performed if a disc exceeds the limitations described above.
BASS TREBLE BALANCE FADER Return to normal mode
Press VIEW. The display will change every time the button is pressed.
Method for creating MP3/WMA files
Bass: -12 ~ +12dB Treble: -12 ~ +12dB Balance : L15 ~ R15 Fader : R15 ~ F15
* The folder No./ folder Name will not be displayed if no file is contained in the folder.
Audio data is compressed using software with MP3/WMA codecs. For details on creating MP3/WMA files, refer to the user’s manual for that software. MP3/WMA files that are playable on this device have the file extensions “mp3” / “wma” Files with no extension cannot be played back (WMA ver. 7-9 are supported). Protected files are not supported.
The display in Radio mode:
Press and hold 5(SCAN) for at least 2 seconds. From the next folder, the first 10 seconds of the first file in each folder is played back in sequence.
FREQUENCY CLOCK FREQUENCY
The display in CD mode:
When a disc is already inserted, press SOURCE/ to switch to the DISC mode.
Press and hold 5(SCAN) again to cancel.
The media that this device can play back are CD-ROMs, CD-Rs, and CD-RWs.
This is the “sound” compression rate specified for encoding. The higher the bit rate, the higher the sound quality, but also the larger the files.
TRACK NO./ELAPSED TIME TEXT (DISC NAME) * 1 TEXT (TRACK NAME) * 1 CLOCK TRACK NO./ELAPSED TIME
2 Turn the Rotary encoder until the desired sound is obtained in each mode.
The mode will change every time the button is pressed.
The display in MP3/WMA mode:
RADIO CD* 1 USB * 2 AUX RADIO
This device supports discs formatted with ISO9660 Level 1 or Level 2.
Optional adapter cable (RCA pin plugs [red, white] 3.5ø miniplugs) or (3.5ø miniplugs)
* 1 Displayed only when a disc has been inserted. * 2 Displayed only when USB memory is connected.
This value shows how many times per second the data is sampled (recorded). For example, music CDs use a sampling rate of 44.1 kHz, so the sound is sampled (recorded) 44,100 times per second. The higher the sampling rate, the higher the sound quality, but also the larger the volume of data.
FILE NAME ALBUM NAME * 2 SONG NAME * 2/ARTIST NAME * 2 CLOCK FOLDER NO./FILE NO.
Under the ISO9660 standard, there are some restrictions to remember. The maximum nested folder depth is 8 (including the root directory). The number of characters for a folder/file name is limited. Valid characters for folder/file names are letters A-Z, a-z, numbers 0-9 and symbols.
The display in AUX mode:
2 While playing back MP3/WMA, press or to select the desired folder.
* 1 Displayed during playback of a disc with CD text. * 2 ID3 tag/WMA tag If an MP3/WMA file contains ID3 tag/WMA tag information, the ID3 tag/WMA tag information is displayed (e.g., song name, artist name, and album name). All other tag data is ignored.
Press 6(RPT) to repeatedly play back the current track. The “ RPT” indicator lights up, and the track (file) will be played repeatedly.
Converting music CDs, WAVE (AIFF) files, and other sound files into the specified audio compression format.
This device also can play back discs in Joliet, Romeo, etc., and other standards that conform to ISO9660. However, sometimes the file names, folder names, etc., are not displayed correctly.
Press 6(RPT) again to cancel.
Song information such as track titles, artist names, album names, etc., written into MP3/WMA files.
Text:
This device supports Multi-Session. This device cannot correctly play back discs recorded with Track At Once or packet writing.
Text compatible CDs contain text information such as the disc name and track name. Such text information is referred to as “text.”
Press and hold 6(RPT) for at least 2 seconds. The “ FOLDER” and “ RPT” indicators appear in the display, and only files in the current folder are repeatedly played back.
The root folder (or root directory) is found at the top of the file system. The root folder contains all folders and files. It is created automatically for all burned discs.
Apple HFS, UDF 1.50, Mixed Mode CD and Enhanced CD (CD- Extra) are not supported.
Press and hold 6(RPT) again to cancel.

USB Memory Connection (Optional)
Information
Indication for CD Player Indication for USB memory Specifications
GENERAL
Installation
Installation and Connections
CD Player not functioning. • Out of operating temperature range +70°C (+158°F) for CD. - Allow the vehicle’s interior (or trunk) temperature to cool.
Power Requirement 12 V DC (11-16 V allowable), Test volage 14.4 V, Negative ground
Connect USB memory 1 Open the cover of the USB connection terminal. 2 Connect the USB memory directly to the USB connection terminal, or via the USB cable.
Before installing or connecting the unit, please read the following and “Operating Instructions” of this manual thoroughly for proper use.
In Case of Difficulty
Tuning Range (CDE-110C/110E/110UB) / (CDE-110) Usable Sensitivity 5 dB/µV (S/N 30 dB) Frequency Response 30-15,000 Hz (±3 dB) Alternate Channel Selectivity 75 dB Stereo Separation 30 dB Image Rejection Ratio 70 dB IF Rejection Ratio 100 dB Signal-to-Noise Ratio 62 dB
87.5-108.0 MHz / 87.7-107.9 MHz
Current Consumption Less than 2.1 A (CD mode; 0.5 W x 4) Maximum Power Output 50 W × 4 (at 1 kHz) volume control maximum Power Output 18 W x 4 (1kHz, 1 %, 4 ohms) Speaker Impedance 4-8 ohms Pre-Output Voltage* 2 V (CD mode, 1 kHz, 0dB) Pre-Output Impedance* 200 ohms Dimensions (W × H × D) 178 × 50 × 160 mm g k 2.1 th gie W
Do not block the unit's heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire.
CD playback sound is wavering. • Moisture condensation in the CD Module. - Allow enough time for the condensation to evaporate (about 1
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.
This unit USB Connection Terminal
hour).
USB memory (Sold Separately)
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
No function or display. • Vehicle’s ignition is off. - If connected following instructions, the unit will not operate
the CD Player Operation section.
Reinforce the head unit with the metal mounting strap (not supplied). Secure the ground lead of the unit to a clean metal spot using a screw (*1) already attached to the vehicle’s chassis.
531-1,602 kHz / 530-1,710 kHz
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts.
A USB memory device may be connected to this unit. With USB memory connected, playback of files on the device is controlled from this unit.
Unable to fast forward or backward the CD. • The CD has been damaged. - Eject the CD and discard it; using a damaged CD in your unit
turn on Connect another USB memory.
USB memory (Sold Separately)
Usable Sensitivity 28 dB/µV (S/N 20 dB)
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.
can cause damage to the mechanism.
Remove USB memory 1 Carefully, pull out the USB memory from the USB cable or the USB connection terminal. 2 Close the cover of the USB connection terminal.
Connect each input lead coming from an amplifier to the corresponding output lead coming from the left rear of the CDE-110/110C/110E/110UB. Connect all other leads of the CDE-110/110C/110E/110UB according to details described in the CONNECTlONS section. 3 Slide the CDE-110/110C/110E/110UB into the dashboard until it clicks. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the detachable front panel.
Sampling Range 8 times oversampling DA Converter 1 bit DAC System Pick-up Type 3-beam Photo Detector Pick Up Light Source Semiconductor laser Wave length 790 nm Laser Power CLASS I Frequency Response 20-20,000 Hz (±1 dB) Signal-to-Noise Ratio 96 dB Total Harmonic Distortion 0.01% (at 1 kHz) Wow & Flutter Below measurable limits Channel Separation 85 dB
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals, etc. can be extremely hazardous.
necessary.
When you install this unit in your car, do not remove the detachable front panel. If the detachable front panel is removed during installation, you might press too hard and warp the metal plate that holds it in place.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure. Precautions
Unable to receive stations. • No antenna or open connection in cable. - Make sure the antenna is properly connected; replace the
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
antenna or cable if necessary.
If you connect a USB memory containing MP3/WMA, you can play these files on this unit.
Unable to tune stations in the seek mode. • If the area you are in is a primary signal area, the antenna may not be grounded and connected properly. - Check your antenna connections; make sure the antenna is
your nearest Alpine dealer.
CD playback sound skips without vibration. • The disc is dirty or scratched. - Clean the disc; damaged disc should be replaced.
1 Press SOURCE/ to switch to the USB AUDIO mode. The mode will change every time the button is pressed.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
properly grounded at its mounting location. • The antenna may not be the proper length. - Make sure the antenna is fully extended; if broken, replace the
Error displays (built-in CD player only). • Mechanical error. - Press . After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest Alpine dealer.
RADIO CD* 1 USB* 2 AUX RADIO
USB requirements 1.1/2.0 Full Speed Maximum Supply Compatibility 500 mA
* 1 Displayed only when a disc has been inserted. * 2 Displayed only when USB memory is connected.
antenna with a new one.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.
2 To pause playback, press BAND/ / . Pressing BAND/ / again will resume the playback.
Bracket Bolt Stud (Included)
CD-R/CD-RW playback not possible. • Close session (finalization) has not been performed. - Perform finalization and attempt playback again.
Input Impedance 10 kohms Allowable external input 2.0 V
m m 5.3 rotc e n n o C Stereo mini-pin
MP3/WMA files are prepared, then stored to a USB memory. This unit can recognise at least 999 folders (including root folder) and 255 files per folder stored in USB memory. Playback may not be performed if a USB memory exceeds the limitations described above. Do not make a file's playback time more than 1,000 minutes.
location.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately.
MP3, WMA is not played back. • Writing error occurred. The MP3/WMA format is not compatible. - Make sure the MP3/WMA has been written in a
This unit Screws (M5 × 8)
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR SHIFT LEVER. Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.
Remove the mounting sleeve from the main unit (see “Removal”).
This device can play back USB memory media.
supported format. Refer to “About MP3/WMA”, then rewrite in the format supported by this device.
This device supports FAT 12/16/32 for USB memory device.
Secure the ground lead of the unit to a clean metal spot using a screw (*3) already attached to the vehicle’s chassis.
Left Rear (+) Speaker Output Lead (Green)
ANT CONT Lead (Blue) Connect this lead to the +B terminal of your power antenna, if applicable.
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (–) Speaker Output Lead (White/Black)
Left Front (+) Speaker Output Lead (White)
Rear Output RCA Connectors RED is right and WHITE is left.
AMP CONT Lead (Blue/White) Connect this lead to the remote turn-on lead of your amplifier or signal processor.
RCA Extension Cable (sold separately)
Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicle’s fuse box or another unused power source which provides (+)12V only when the ignition is turned on or in the accessory position.
Front AUX Input Terminal This terminal allows for input of audio from an external device (such as a portable player), using a commercially- available converter cable.
USB Connection Terminal Connect USB memory (sold separately)
Battery Lead (Yellow) Connect this lead to the positive (+) post of the vehicle’s battery.
Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.
Right Front (+) Speaker Output Lead (Gray)
Right Front (–) Speaker Output Lead (Gray/Black)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
SPEAKER LEFT REAR
SPEAKER LEFT FRONT Front Left
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.