Instruction/ maintenance manual of the product IS0152 Faria Instruments
Go to page of 23
Owner’s Manual Pilot ™ I ISO152B ECR#3704 6/2003 IS0152 Pilot I Displays, Speedometer in MPH and Knots Trip Log Clock Voltmeter Air & Surface Temp.
Index Description Ke y Pad Functions Page 1 Installation 4 pin Connector Page 2 6 pin Connector Page 2 Operations General Modes Pow er On Page 3 Illumination Page 3 Normal Mode Page 3 Select Mode Acti.
MODE S T 1 T 1 KL D F FA M DIS KTS MPH Fa ria Pilot I Description The F aria Pilot I system is a multifunctional instr ument designed to giv e tw o simultaneous readouts of sev eral different and independent functions on an upper and lo wer LCD displa y .
Installation: CA UTION: Disconnect the battery during installation. T ighten nuts on the backclamp only slightl y more than you can tighten with your fingers. Six inch- pounds of torque are sufficient. Ov er- tightening could result in damage to the instrument and may v oid your w ar ranty .
Operation: Pow e r ON: The Pilot I instrument will tur n on when the ignition key s witch is set to the r un position. When the ignition key switch is turned to the off position, the Pilot I will turn off. *If the mode button is accidentally pressed for an extended period of time the unit will enter a diagnostic OFF Mode.
Selecting upper or lo wer acti ve displa y: Activ ate the Select Mode and while the displa y is flashing, press the “Up” ar ro w to select the upper displa y as active or the “Do wn” ar ro w to select the lo wer displa y as the active displa y .
If no buttons are pushed within 5 seconds, the Pilot will rev er t automaticall y to the Normal Mode . Y ou can also enter the Edit Mode w hile in the Select Mode . The Pilot displa y will then stop flashing (Select Mode) indicating the change to the Edit Mode .
will flash on the LCD next to the “S” and the audible alarm will sound rapidly . When the deep depth setting is read by the depth sounder , the Function Indicator will flash on the LCD next to the “D” and the audible alarm will sound at 2 beeps per second.
Press and hold the “MODE” button until the Pilot beeps to select the Edit Mode . Continue pressing the “MODE” button quickly until the Function Indicator points to the “KL ” indicating the keel offset function. Press and hold only the “Do wn” ar ro w key pad to adjust the reading to the desired depth.
Continue pressing the “MODE” button again until the Function Indicator is pointing to either the left(T1) or the right(T1). Starting and Stopping the Timer . Press either “Up” or “Do wn” ar ro w button to start or stop the timer at any time.
Setting the clock: Press and hold the “MODE” button until the Pilot beeps to select the Edit Mode . Press the “Up” or “Do wn” ar ro w keypads once to set each minute. Press and hold the “Up” or “Do wn” ar ro w ke ypads to set the hours.
Selecting the Speedometer Units. Press and hold the “MODE” button until the Pilot beeps to select the Edit Mode . Continue pressing the “MODE” button quickly until the lo wer displa y reads “Un” (units).
Continue pressing the “MODE” button again until the Function Indicator is pointing to DIS. (The Function Indicator will also automatically point to the last unit type selected. Y ou are no w in the Distance Log Function Selecting the Distance Log Units.
T 1 T 1 S KL D F FA M DIS KTS MPH Press either the “Up” or “Do wn” ar ro w button to clear the Log reading to zero. W ater & Air / Bait-well T emperatur e Description: The Pilot I will monitor water surface temperature. The (Setting units F ahrenheit (F), or Centigrade (C), in either function sets the units for both).
V oltmeter: Description: The V oltmeter continuously monitors the battery system voltage supplied to the Pilot I. The V oltmeter has a user adjustable lo w and high voltage alarm feature.
Press the “MODE” button. The upper displa y changes to “bAtH” and the lo wer displa y shows the current high voltage w arning setting. Press either the “Up” or “Do wn” ar ro w button to adjust the high voltage alarm setting.
Page 15 This page left blank intentionally..
Har ness HN0362 4 - pin connector Y amaha adaptor 4- pin connector (CN0082) Multi-bullets to Y amaha Engine Harness Black Y ellow Red Red Purple Black Pin A Red +12 Battery Pin B Purple +12 Ignition P.
Har ness HN0362 6 - pin connector Y amaha adaptor Red Green Green 6- pin connector (CN0083) Pin A Plug Not used Pin B Plug Not used Pin C Green Sensor Ground Pin D White W ater T emperature Pin E Red Air T emperature Pin F White/Blue Speedo Sensor ECR 2065 2/12/02 To Pilot I Shrink T ubing or Wrap W ater T emp.
Har ness HN0365 4 - pin connector 4- pin connector (CN0082) To Pilot I Shrink T ubing or Wrap Blue Red Purple Black Black Blue Pin A Red +12 Battery Pin B Purple +12 Ignition Pin C Black Depth Sounder.
Har ness HN0365 6 - pin connector To Pilot I Shrink T ubing or Wrap W ater T emp. Sensor signal T an/Blue Stripe White Green T an/White Stripe White Brown Black Black Black White/Blue Stripe 6- pin co.
NOTES.
Copyright 2003 by the Thomas G. Faria Corporation, Uncasville CT No part of this publication may by reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the company.
An important point after buying a device Faria Instruments IS0152 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Faria Instruments IS0152 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Faria Instruments IS0152 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Faria Instruments IS0152 you will learn all the available features of the product, as well as information on its operation. The information that you get Faria Instruments IS0152 will certainly help you make a decision on the purchase.
If you already are a holder of Faria Instruments IS0152, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Faria Instruments IS0152.
However, one of the most important roles played by the user manual is to help in solving problems with Faria Instruments IS0152. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Faria Instruments IS0152 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
