EN
Official user manual

321 Studios FH110D60E

39 pages·901 KB·Coffeemaker·PDF·ENDEFRITNLJA
321 Studios FH110D60E
Table of Contents 80 sections OIL FURNACE INSTALLATION INSTRUCTIONS · MODELS · WARNING · FOR YOUR SAFETY · … ShowHide
OIL FURNACE INSTALLATION INSTRUCTIONSp.1MODELSp.1WARNINGp.1FOR YOUR SAFETYp.1IMPORTANT NOTICEp.1GETTING OTHER INFORMATION and PUBLICATIONSp.3FOR MORE INFORMATION, CONTACT THESE PUBLISHERS:p.3INSTALLATION and OPERATING INSTRUCTIONSp.4EQUIPMENT SELECTIONp.4LOCATING THE FURNACEp.4TABLE 1 MINIMUM CLEARANCESp.4MIS-1815 Ap.5FLF/R MODELS DIMENSIONS (INCHES)p.5TABLE 2p.5FLF/R MODELS DIMENSIONSp.5FIGURE 1p.5"FLF" FLUEp.5KNOCKOUTp.5FLF/FLR 085, 110 AND 140p.5SPECIFICATION SHEETp.5DUCT SUPPLYp.5DUCTp.5HIGH VOLTAGEp.5KNOCKOUT REAR FLUEp.5LOW VOLTAGEp.5E Fp.5OPTIONALp.5ENTRANCEp.5FRESH AIRp.5TOP VIEWp.5OILp.5ON "FLR" MODELSp.5FILTERp.5DOORp.5RETURNp.5MIS-1814 Ap.6OPENING FH085 AND FH110p.6RIGHT SIDE VIEWp.6REAR CLEANOUTp.6VOLTAGEp.6FLUEp.6HIGHp.6SUPPLYp.6FH MODELS DIMENSIONSp.6FIGURE 2p.6FRONT VIEWp.6VESTIBULEp.6LEFT SIDE VIEWp.6OPENINGp.6(CUT OUT)p.6FIGURE 3 FC085 MODEL DIMENSIONSp.7SUPPLY OPENINGp.7FC085 SPECIFICATIONp.7SHEETp.7OPTIONAL OIL ENTRANCEp.7RETURN OPENINGp.7BOTTOM VIEWp.7INSTALLING THE FURNACEp.8DUCT WORKp.8INSTRUMENTS REQUIRED FOR PROPER SETUP OF THE FURNACEp.8IMPORTANTp.8INSTALLING A COOLING UNITp.8INSTALLATIONp.8INADEQUATE SUPPLY AIR and/or RETURN AIR DUCT SYSTEMSp.8NOTE: IF DRAIN PAN IS ANYTHING OTHERp.8WIRINGp.9FIELD WIRINGp.9FACTORY WIRINGp.9FIGURE 4 TYPICAL UNIT SETUPp.10FLF UNIT SHOWNp.10TYPICAL UNITp.10SETUP (FLF UNIT SHOWN)p.10Left side high voltage (unit power) entrancep.10Inspection doorp.10Left side low voltage (thermostat) entrancep.10Right side low voltage (thermostat) entrancep.10Left side oil line entrance for opt. air bootp.10To thermostat and optional A/C unitp.10Left side oil line entrancep.10To power sourcep.10
Page 1 of the 321 Studios FH110D60E user manual — IMPORTANT NOTICE
Page 1 · click to enlarge
Page 1

OIL FURNACE INSTALLATION INSTRUCTIONS

MODELS

FH085D36E FH110D48E FH110D60E FLF085D36E FLF110D48E FLF110D60E FLR085D36E FLR110D48E FLR110D60E FLR140D60E FC085D36E

WARNING

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION.

THIS INSTALLATION MUST COMPLY WITH THESE INSTRUCTIONS AND THE REQUIREMENTS OF ALL GOVERNING CODES AND ORDINANCES FOR THE INSTALLATION LOCATION.

IT IS THE RESPONSIBILITY OF INSTALLER TO KNOW AND UNDERSTAND ALL OF THESE REQUIREMENTS.

FAILURE TO DO SO COULD CREATE A HAZARD RESULTING IN PROPERTY DAMAGE, BODILY INJURY OR DEATH.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

IMPORTANT NOTICE

THIS FURNACE IS NOT INTENDED FOR USE AS A CONSTRUCTION HEATER. USE OF THIS FURNACE DURING CONSTRUCTION AND FINISHING PHASES OF A STRUCTURE IS CONSIDERED AS "OPERATION IN A CORROSIVE ATMOSPHERE" AND "UNUSUAL, NEGLIGENT OR IMPROPER USE" AND AS SUCH ARE CONSIDERED EXCLUSIONS BY THE BARD MANUFACTURING COMPANY LIMITED WARRANTY.

321 Studios FH110D60E — IMPORTANT NOTICE diagram (page 1)
Fig. 1

Bard Manufacturing Company Bryan, Ohio 43506

Manual2100-422B Supersedes: 2100-422A File: VOL. I, TAB 3 Date: 09-23-03

Since 1914...Moving ahead just as planned.

Copyright 2003

Page 2 of the 321 Studios FH110D60E user manual — OIL FURNACE INSTALLATION INSTRUCTIONS
Page 2 · click to enlarge
Page 2
Page 2 of the 321 Studios FH110D60E user manual — OIL FURNACE INSTALLATION INSTRUCTIONS
Page 3 of the 321 Studios FH110D60E user manual — FOR MORE INFORMATION, CONTACT THESE PUBLISHERS:
Page 3 · click to enlarge
Page 3

GETTING OTHER INFORMATION and PUBLICATIONS

These publications can help you install the furnace. You can usually find these at your local library or purchase them directly from the publisher. Be sure to consult current edition of each standard.

FOR MORE INFORMATION, CONTACT THESE PUBLISHERS:

ACCA Air Conditioning Contractors of America 1712 New Hampshire Ave. N.W. Washington, DC 20009 Telephone: (202) 483-9370 Fax: (202) 234-4721

National Fuel Gas Code ANSI Z223.1/NFPA54

National Electrical Code ANSI/NFPA 70

ANSI American National Standards Institute 11 West Street, 13th Floor New York, NY 10036 Telephone: (212) 642-4900 Fax: (212) 302-1286

Standard for the Installation ANSI/NFPA 90A of Air Conditioning and Ventilating Systems

Standard for Warm Air ANSI/NFPA 90B Heating and Air Conditioning Systems

ASHRAE American Society of Heating Refrigerating, and Air Conditioning Engineers, Inc. 1791 Tullie Circle, N.E. Atlanta, GA 30329-2305 Telephone: (404) 636-8400 Fax: (404) 321-5478

Standard for Chimneys, Fireplaces, Vents ... NFPA 211 and Solid Fuel Burning Appliances

Load Calculation for ACCA Manual J Residential Winter and Summer Air Conditioning

NFPA National Fire Protection Association Batterymarch Park P.O. Box 9101 Quincy, MA 02269-9901 Telephone: (800) 344-3555 Fax: (617) 984-7057

Duct Design for Residential ACCA Manual D Winter and Summer Air Conditioning and Equipment Selection

Page 4 of the 321 Studios FH110D60E user manual — TABLE 1 MINIMUM CLEARANCES
Page 4 · click to enlarge
Page 4

INSTALLATION and OPERATING INSTRUCTIONS

EQUIPMENT SELECTION

LOCATING THE FURNACE

An accurate heating load calculation must be conducted using American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) or Air Conditioning Contractors of America (ACCA) manuals. Do not add a large safety factor above the calculated value. If the calculated heating load requirement exceeds the heating capacity rating of a given model, use only the next larger size available. Never increase by any more than absolutely necessary based upon available equipment heating capacities. Always select based upon heat capacity (output), never use input capacities.

When installing the furnace be sure to provide adequate space for easy service and maintenance. Locate the furnace as close to the chimney as practical, giving consideration to the accessibility of the oil burner, controls, and blower for service. Allow a minimum of 24 inches at front of furnace for servicing oil burner. Allow adequate room for filter and blower maintenance. Clearance from combustible material as stated on the furnace and repeated in Table 1 must be maintained. For damp basement installations, a raised concrete pad is recommended. This will help keep the bottom of the furnace dry and reduce the risk of rusting.

An oil burner must have a generous supply of combustion air to operate properly. The flow of combustion and ventilating air must not be obstructed from reaching the furnace. See “Combustion Air Requirements” section.

obligation of the purchaser to contract a qualified installer to assure that installation is adequate and is in conformance with governing codes and ordinances.

The furnace area must be kept clear and free of combustible materials, gasoline and other flammable vapors and liquids.

This unit is not designed for mobile home or trailer installations. Always install furnace in a level position.

TABLE 1 MINIMUM CLEARANCES

ModelMinimumInstallationClearnaces—InchesMinimumService Clearances FurnacePlenum1 DuctFlue PipeFloor FrontBackSidesTopSidesFrontBackSides FH085D36E FH110D48E FH110D60E4 4 41 1 12 2 22 2 22 2 22 2 29 9 9C C C24 24 24— — —— — — FLF085D36E FLR085D36E FLF110D48E FLF110D60E60 18 0 022229NC242418* FLR110D48E FLR110D60E FLR140D60E FC085D36E618 18 18 122229NC**2424 24 24 —18* 18* 18* —

For the first three (3) feet from plenum. After three (3) feet, no clearance required. C Combustible flooring NC Noncombustible floor * Maintained on one side or the other to achieve filter access and/or blower service. ** Floor must be noncombustible. For furnace only installation can be installed on combustible flooring only when installed on special base part no. CFB7 available from factory. When air conditioning coil cabinet DCB23-22 is used then use special base part no. CFB23.

Page 5 of the 321 Studios FH110D60E user manual — "FLF" FLUE
Page 5 · click to enlarge
Page 5

. a i D H J e zi S . o N

d e s U

s g n i n e p O n o it c e n o C e u l F s r e tli F ri A 1

r a e R 6 6 5 2 6 . 1 3 5 2 6 . 1 3 5 2 1 . 5 5 2 1 . 5 1 x 0 2 x 6 1 1 x 0 2 x 6 1 1 1

1

E 0 6 D 0 4 1 R L F 6 2 0 5 2 . 0 5 5 2 6 . 7 4 0 2 x 5 2 6 1 x 5 2 r a e R 6 5 2 1 . 2 4 - - - 1 x 5 2 x 0 2 1

1 x 0 2 x 0 2 1 x 0 2 x 0 2 1 x 0 2 x 0 2 1 x 0 2 x 0 2

321 Studios FH110D60E — MIS-1815 A diagram (page 5)
Fig. 2

MIS-1815 A

5 2 1 . 5 5 2 1 . 5 5 2 1 . 5 5 2 1 . 5

Model NumberCabinet A B C Width Depth HeightPlenum OpeningsFlueConectionAirFilters 1 B DepthC HeightDxE SupplyDxF ReturnLocationG Dia.HJSizeNo. Used FLF085D36E FLR085D36E23 2348.125 48.12536.625 36.62522x20 22x2022x14 22x14Front Rear6 631.625 31.6255.125 5.12516x20x1 16x20x11 1 FLF110D48E FLF110D60E FLR110D48E FLR110D60E2348.12540.62522x2022x14Front Front Rear Rear635.6255.12520x20x11 FLR140D60E2650.25047.62525x2025x16Rear642.125---20x25x11

5 2 6 . 5 3 5 2 6 . 5 3 5 2 6 . 5 3 5 2 6 . 5 3

FLF/R MODELS DIMENSIONS (INCHES)

n r u t e R n o it a c o L G

6

E 6 3 D 5 8 0 R L F 3 2 3 2 5 2 1 . 8 4 5 2 1 . 8 4 5 2 6 . 6 3 5 2 6 . 6 3 0 2 x 2 2 0 2 x 2 2 4 1 x 2 2 4 1 x 2 2 tn o r F

tn o r F

tn o r F

r a e R

r a e R

Washable type filter 1” nom. thickness

TABLE 2

y l p p u S F x D

4 1 x 2 2 4 1 x 2 2 4 1 x 2 2 4 1 x 2 2

t e n i b a C m u n e l P

t h g i e H E x D

0 2 x 2 2 0 2 x 2 2 0 2 x 2 2 0 2 x 2 2

5 2 6 . 0 4 5 2 6 . 0 4 5 2 6 . 0 4 5 2 6 . 0 4

FLF/R MODELS DIMENSIONS

h t p e D C

321 Studios FH110D60E — FLF/R MODELS DIMENSIONS diagram (page 5)
Fig. 3

5 2 1 . 8 4 5 2 1 . 8 4 5 2 1 . 8 4 5 2 1 . 8 4

h t d i W B

FIGURE 1

A

3 2 3 2 3 2 3 2

E 6 3 D 5 8 0 F L F

E 8 4 D 0 1 1 F L F

E 0 6 D 0 1 1 F L F

E 8 4 D 0 1 1 R L F

E 0 6 D 0 1 1 R L F

r e b m u N

l e d o M

"FLF" FLUE

KNOCKOUT

FLF/FLR 085, 110 AND 140

J

SPECIFICATION SHEET

DUCT SUPPLY

DUCT

HIGH VOLTAGE

KNOCKOUT REAR FLUE

LOW VOLTAGE

E F

"FLF" FLUE

OPTIONAL

ENTRANCE

OPTIONAL

ENTRANCE

ENTRANCE

OPTIONAL

ENTRANCE

FRESH AIR

KNOCKOUT

TOP VIEW

OIL

OIL

ON "FLR" MODELS

FILTER

DOOR

G

RETURN

D

H

Page 6 of the 321 Studios FH110D60E user manual — RETURN
Page 6 · click to enlarge
Page 6

MIS-1814 A

SPECIFICATION SHEET

321 Studios FH110D60E — MIS-1814 A diagram (page 6)
Fig. 4

OPENING FH085 AND FH110

RIGHT SIDE VIEW

REAR CLEANOUT

LOW VOLTAGE

KNOCKOUT

ENTRANCE

ENTRANCE

ENTRANCE

VOLTAGE

OPTIONAL

FLUE

DOOR

HIGH

OIL

SUPPLY

FH MODELS DIMENSIONS

321 Studios FH110D60E — REAR CLEANOUT diagram (page 6)
Fig. 5

FIGURE 2

FRONT VIEW

TOP VIEW

KNOCKOUT

HIGH VOLTAGE

LOW VOLTAGE

KNOCKOUT

OPTIONAL

ENTRANCE

OPTIONAL

ENTRANCE

OPTIONAL

ENTRANCE

ENTRANCE

FRESH AIR

KNOCKOUT

VESTIBULE

FLUE

DOOR

FLUE

OIL

OIL

321 Studios FH110D60E — FIGURE 2 diagram (page 6)
Fig. 6

LEFT SIDE VIEW

RETURN

OPENING

(CUT OUT)

19 1/4" · 16"

Page 7 of the 321 Studios FH110D60E user manual — RETURN OPENING
Page 7 · click to enlarge
Page 7

FIGURE 3 FC085 MODEL DIMENSIONS

321 Studios FH110D60E — FIGURE 3 FC085 MODEL DIMENSIONS diagram (page 7)
Fig. 7

SUPPLY OPENING

FC085 SPECIFICATION

SHEET

TOP VIEW

321 Studios FH110D60E — SUPPLY OPENING diagram (page 7)
Fig. 8
321 Studios FH110D60E — SUPPLY OPENING diagram (page 7)
Fig. 9

FRONT VIEW

OPTIONAL OIL ENTRANCE

321 Studios FH110D60E — OPTIONAL OIL ENTRANCE diagram (page 7)
Fig. 10

RETURN OPENING

BOTTOM VIEW

Page 8 of the 321 Studios FH110D60E user manual — NOTE: IF DRAIN PAN IS ANYTHING OTHER
Page 8 · click to enlarge
Page 8

INSTALLING THE FURNACE

DUCT WORK

The air distribution system should be designed and installed in conformance with manuals published by Air Conditioning Contractors of America (ACCA) as set forth in Manual D, or ASHRAE publications.

INSTRUMENTS REQUIRED FOR PROPER SETUP OF THE FURNACE

It is important that a set of instruments capable of the following requirements be used for the setup of this furnace to ensure proper and safe operation:

IMPORTANT

1. Oil pump pressure gauge that measures up to 150 PSI.

When a furnace is installed so that supply ducts carry air circulated by the furnace to areas outside the space containing the furnace, the return air must also be handled by a duct(s) sealed to the furnace casing and terminating outside the space containing the furnace This is to prevent drawing possible hazardous combustion products into the circulated air.

2. Smoke gun to pull smoke samples from flue.
3. Draft gauge that will measure -.02” water column (W.C.)
4. Duct static pressure gauge 0-1.0” W.C. range.
5. Temperature gauge that can read from 50° F up to 700° F.
6. A gauge to measure CO 2 or O 2 .

INSTALLING A COOLING UNIT

INSTALLATION

When the furnace is used in connection with a cooling unit*, the furnace shall be installed parallel with or on the upstream side of the cooling unit to avoid condensation in the heating element. With a parallel flow arrangement, the dampers or other means used to control flow of air shall be adequate to prevent chilled air from entering the furnace, and if manually operated, must be equipped with means to prevent operation of either unit, unless the damper is in the full heat or cool position.

A typical installation is shown in Figures 4 and 5. All parts of the furnace installation (furnace, oil tank and piping systems, combustion and ventilation air, venting, etc.) must comply with NFPA31, Installation of Oil Burning Equipment -- latest edition. This drawing shows the typical connecting parts needed to correctly install this furnace. Make sure that all parts of the heating system comply with the local codes.

Check the furnace and your load calculation to verify that the unit is properly sized. (Refer to Equipment Selection” section on Page 2.)

* A cooling unit is an air conditioning coil, heat pump coil or chilled water coil.

The correct size of unit needed may be substantially smaller than the unit being replaced due to home improvements and technology advancements since the initial installation.

When installing a cooling unit above an FH or FL (below on an FC) series furnace, the coil must be spaced far enough from the furnace outlet to assure proper operation of the furnace. Bard supplied coils, when used with Bard supplied coil cabinets, are automatically positioned.

INADEQUATE SUPPLY AIR and/or RETURN AIR DUCT SYSTEMS

For top discharge FH and FL models, when coils are installed without using Bard coil cabinets or coils of another brand are used, the coil drain pan should be located a minimum of two (2) inches above the top of the furnace cabinet. If a greater clearance is specified by the coil manufacturer then it would apply.

Short cycling because of limit control operation can be created by incorrectly designed or installed supply and/ or return air duct systems.

The duct systems must be designed using ASHRAE or ACCA design manuals and the equipment CFM and external static pressure ratings to insure proper air delivery capabilities.

NOTE: IF DRAIN PAN IS ANYTHING OTHER

THAN A STEEL PAN PARTICULAR ATTENTION MUST BE GIVEN TO THE INSTALLATION INSTRUCTIONS FOR THE COIL TO MAKE SURE IT IS ACCEPTABLE FOR USE WITH THESE OIL FURNACES HAVING MAXIMUM OUTLET AIR TEMPERATURE OF 200° F.

On replacement installations, particularly if equipment is oversized, the duct systems can easily be undersized. Modifications may be required to assure that the equipment is operating within the approved temperature rise range when under full rated input conditions, and that no short cycling on limit controls is occurring.

See CFM versus static pressure curves on pages 33-36 for additional information.

Page 9 of the 321 Studios FH110D60E user manual — FIELD WIRING
Page 9 · click to enlarge
Page 9

WIRING

FIELD WIRING

FACTORY WIRING

All wiring must conform to the National Electrical Code and all local codes. A separate fuse or breaker should be used for the furnace.

All units are fully factory wired. Multispeed blowers are factory wired on high speed for cooling/manual fan operation. Heating speeds are wired for the largest input and may need lower speed for field installed low input nozzle. If replacement wire is necessary, use 105 degrees C minimum. See electrical data, Table 3.

ModelVolts-HZ-PHTotal AmpsBlowerMotorBurnerMotorMinimum Circuit AmpacityMax.Time DelayFuse or HACR CircuitBreaker HPFLAHPFLA FH085D36E115-60-19.21/37.51/71.71515 FH110D48E115-60-112.21/210.51/71.71620 FH110D60E115-60-114.23/412.51/71.71920 FLF085D36E115-60-117.31/35.61/71.71515 FLR085D36E115-60-117.31/35.61/71.71515 FLF110D48E115-60-112.21/210.51/71.71620 FLR110D48E115-60-112.21/210.51/71.71620 FLF100D60E115-60-114.23/412.51/71.71920 FLR100D60E115-60-114.23/412.51/71.71920 FLR140D60E115-60-114.23/412.51/71.71920 FC085D36E115-60-17.31/35.61/71.71515
Page 10 of the 321 Studios FH110D60E user manual — Air Boot knockout (optional)
Page 10 · click to enlarge
Page 10

FIGURE 4 TYPICAL UNIT SETUP

FLF UNIT SHOWN

WARNING

TYPICAL UNIT

ALL WIRING MUST CONFORM TO THE NATIONAL ELECTRIC CODE AND ALL LOCAL

SETUP (FLF UNIT SHOWN)

!

CODES.

Left side high voltage (unit power) entrance

Inspection door

Left side low voltage (thermostat) entrance

Right side low voltage (thermostat) entrance

Left side oil line entrance for opt. air boot

To thermostat and optional A/C unit

Left side oil line entrance

To power source

Oil line (see burner pump inst. for hookup info.)

Shut off switch (if not fused, power line must include fuse or circuit breaker)

Air Boot knockout (optional)

Control panel (junction box in FH units)

Power Wires: Black (HOT) White (NEUTRAL) Green (GROUND)

Right side high voltage (unit power) entrance

Right side oil line entrance

Page 11 of the 321 Studios FH110D60E user manual — i n e d
Page 11 · click to enlarge
Page 11

FIGURE 5 TYPICAL FLUE INSTALLATION REQUIREMENTS

FRONT FLUE LOWBOY MODEL SHOWN

(REPRESENTS ALL MODELS)

INSTALLER NOTE:

Follow all appropriate standards for installing needed venting system.

Draft Regulator (Be sure to follow installation inst. supplied with regulator).

1/4 inch per 1 foot rise

90° Rotatable Flue Box on front flue models (remove appropriate cabinet knockout). Mounting screws located under flue box cover.

i n e d

h

i m

n e

y

Clean-out Door (keep closed)

Optional Fresh Air Boot (remove rect. knockout).

Show 4 more labels / short text on this page
Thimble · Flue Box Cover · Optional Flue Locations · Oil Burner
Page 12 of the 321 Studios FH110D60E user manual — FIGURE 6 TYPICAL SINGLE INSIDE TANK INSTALLATION
Page 12 · click to enlarge
Page 12

OIL LINE PIPING

BECKETT AFG OIL BURNER

First determine whether the pipe system is to be a single line system or a two line system. All connections must be absolutely air tight or you will have a malfunction of the burner. When installing the piping, a good oil filter should be installed close to the burner. A single line system is recommended for gravity feed.

This furnace is equipped with a high static Beckett AFG oil burner which is designed to produce adequate draft in nearly any vertically vented application. The burner employs the latest time tested controls of the highest quality. The controls consist of a high voltage Beckett solid state igniter, a Beckett “CleanCut” oil pump with an integral solenoid valve, and a Beckett R7184B primary control.

A typical single inside tank installations shown in Figure 6. For installation details for this and other tank configurations, refer to NFPA31 -- latest edition. All tank and pipe setups must comply with NFPA31.

FIGURE 6 TYPICAL SINGLE INSIDE TANK INSTALLATION

Vent Cap

2" Cap

2" Fill Pipe

1-1/4" Vent Pipe Return Line

Guage

Bushing, 2" x 1-1/2" or 1-1/4"

Oil Tank

Gate Valve

3/8" x 4" nipple

3/8" x 3/8" Adapter

3/8" O.D. Copper Fuel Tubing

Bushing Legs (either 1-1/4"x10" or 1-1/2"x10" nipples)

Oil Filter

6"

Page 13 of the 321 Studios FH110D60E user manual — BECKETT “CLEANCUT” OIL PUMP
Page 13 · click to enlarge
Page 13

These controls were selected for their proven high quality, dependability, and serviceability. With proper maintenance this burner assembly will provide many years of reliable service.

BECKETT SOLID STATE IGNITER

This igniter differs from the traditional iron core transformer in that it produces a 14,000 volt spark instead of a 10,000 volt spark of the iron core transformer. This hotter spark provides for cleaner, faster ignitions. Being solid state technology this igniter is less susceptible to problems caused by voltage variations. It also has a greater ability to ignite cold and/or inconsistent oil. The solid state igniter is wired to the primary control the same as an iron core transformer.

All units are shipped with the oil burner installed, and with high rate oil nozzle installed designed for use with No. 1 or No. 2 fuel oil. Inspect firepot refractory before firing to be sure it has not been jarred out of position in shipment. Burner air tube must not extend beyond inside surface of firepot. Burner head should be centered on the combustion chamber opening. See Figures 19 and 20.

BECKETT R7184B PRIMARY CONTROL

WARNING

The R7184B Interrupted Electronic Oil Primary is a line voltage, safety rated, interrupted ignition oil primary control for residential oil burners. The R7184B used with a cad cell flame sensor, operates the oil burner and oil valve. The primary controls fuel oil, senses flame, controls ignition spark and is designed to notify a remote alarm circuit before going into lockout when equipped with a flame monitoring system.

Never attempt to use gasoline in your furnace. Gasoline is more combustible than fuel oil and could result in a serious explosion causing damage, injury or death.

This primary control possesses the latest technology, is a very simple control to operate and provides additional troubleshooting features to ease service and reduce down time. The operational guide for the R7184B primary control is provided following on Page 12.

The following is a detailed explanation of each control included in the Becket AFG Oil Burner, how each operates, how to set up the burner, and how to troubleshoot problems should they occur.

BECKETT “CLEANCUT” OIL PUMP

This oil pump is equipped with an oil solenoid valve installed in the pump housing. This feature provides quick cutoffs resulting in reduction in smoke after the burner shuts down. This is a time proven pump design and is capable of both one and two pipe systems. This pump requires a pre-purge style primary control such as the R7184B primary. All installation and set up instructions are outlined in the “Oil Pump Specification” section of the installation instructions manual.

Page 14 of the 321 Studios FH110D60E user manual — Electronic Blower Control Board (EBC)
Page 14 · click to enlarge
Page 14

BECKETT R7184B PRIMARY

OPERATIONAL GUIDE

Pre-Purge Delay – 15 seconds on delay LED Codes – Flashing 1/2 second on / 1/2 second off – system is locked out or in restricted mode

(hard lockout). – Flashing 2 seconds on / 2 seconds off – control is in recycle mode (soft lockout). – ON – CAD cell is sensing flame – OFF – CAD cell is not sensing flame.

Ignition Trials – On any given call for heat the control will allow three ignition trials. After the three trials the control will go into a soft lockout mode. The LED will flash 2 seconds on and 2 seconds off when in this recycle mode. The control may then be reset by pressing the RED reset button on the control. If within the same original call for heat the control will again allow three ignition trials followed by another soft lockout and a 2 second on / 2 second off LED code. The control my be reset one additional time by pressing the red reset button. This will allow three final ignition trials. If all three of the final ignition trials

fail then the control goes into a hard lockout or Restricted Mode. This series of ignition failures must all occur with the original call for heat in order to reach the Restricted Mode. The LED will now flash 1/2 second on / 1/2 second off indicating the restricted mode. The control can be resurrected from the restricted mode only by pressing and holding the red reset button for approximately 30 seconds until the LED flashes twice. Removing unit power or resetting the thermostat will not reset the control

Checking CAD Cell – With a call for heat and the burner ignited, press and release the red reset button. The LED will go out and then flash 1, 2, 3, or 4 times before returning to the run mode. The CAD cell resistance must be below 1600 ohms for proper operation.

– 1 flash – Less than 400 ohms – 2 flashes – More than 400 and less than 800 ohms – 3 flashes – More than 800 and less than 1600 ohms – 4 flashes – More than 1600 and less than 5000 ohms

Burner Option – Flame Quality Monitor This control is trained to recognize and remember a good flame based on initial burner set up. Control then monitors the flame via the CAD cell signal for deviation in the combustion characteristics of the burner. If the control senses a deviation on the high side or on the low side from the original set up condition for three consecutive cycles, it will trigger an alarm circuit which can be tied to an audible local device to signal the home owner or into the home security system. Upon being notified of the of the

alarm, the security agency will notify the dealer of choice based upon information supplied by the home owner. The system will also be capable of being connected to a phone line that will contact the dealer directly with the alarm. This alarm will typical sound 3 to 5 days prior to the primary control going into lockout giving the service agency a prior notice before a sooting condition or other failure can occur resulting in untold savings. This monitor system is available through your local distributor under the Honeywell part no. QS7100F.

Electronic Blower Control Board (EBC)

blower on and off timings for both heating and cooling speeds are timed automatically. The heating blower off delay can be selected from four different timings by moving the selection jumper. The timings are as follows:

This furnace is equipped with an Electronic Blower Control (EBC) which controls all comfort air blower operations. This EBC has three relays; one for heating speed, one for cooling speed, and one which isolates the T–T signal from the oil primary control.

Heating Blower ON delay – 75 seconds from a call for heat.

This EBC is designed to be very simple and dependable. This basic control allows for easy troubleshooting and maintenance. As illustrated in Figure 7 all connections are well marked. The

Heating Blower OFF delay – Selectable in seconds: 150, 180. 210 or 240. Factory shipped at 240.

Cooling Blower ON delay – 6 seconds from a call for cooling.

Cooling Blower OFF delay – 60 seconds.

Page 15 of the 321 Studios FH110D60E user manual — COOLING BLOWER SPEED CONNECTION
Page 15 · click to enlarge
Page 15

FIGURE 7 ELECTRONIC BLOWER CONTROL

TRANSFORMER 24V SECONDARY CONNECTIONS THERMOSTAT CONNECTIONS

3 AMP FUSE

HEATING BLOWER

OFF DELAY ADJUSTMENT

IN SECONDS.

OIL PRIMARY T-T CONNECTIONS

LINE VOLTAGE CONNECTION (HOT)

HUMIDIFIER CONNECTION

UNUSED BLOWER MOTOR SPEED CONNECTIONS

HEATING BLOWER SPEED CONNECTION

LINE VOLTAGE CONNECTION (COM, L2) ELECTRIC AIR CLEANER CONNECTION

COOLING BLOWER SPEED CONNECTION

Page 16 of the 321 Studios FH110D60E user manual — IMPORTANT
Page 16 · click to enlarge
Page 16

TABLE 4 FURNACE DATA

d r a d n a t S d e ll a t s n I e c a n r u F n o it p O d e ll a t s n I d l e i F s

2 g n it a e H

2 g n it a e H

2 g n it a e H

1 e l z z o N

1 e l z z o N

1 e l z z o N

t u p n I

y ti c a p a C

t u p n I

y ti c a p a C

t u p n I

y ti c a p a C

r e b m u N l e d o M

H U T B

H U T B

H U T B

H U T B

H U T B

H U T B

E 6 3 D 5 8 0 F L F 5 7 . 0 0 0 , 5 0 1 0 0 0 , 5 8 5 6 . 0 0 0 , 1 9 0 0 0 , 4 7 5 5 . 0 0 0 , 7 7 0 0 0 , 3 6

E 6 3 D 5 8 0 R L F 5 7 . 0 0 0 , 5 0 1 0 0 0 , 5 8 5 6 . 0 0 0 , 1 9 0 0 0 , 4 7 5 5 . 0 0 0 , 7 7 0 0 0 , 3 6

E 8 4 D 0 1 1 F L F 0 0 . 1 0 0 0 , 0 4 1 0 0 0 , 3 1 1 5 8 . 0 0 0 , 9 1 1 0 0 0 , 6 9 A N A N A N

E 8 4 D 0 1 1 R L F 0 0 . 1 0 0 0 , 0 4 1 0 0 0 , 3 1 1 5 8 . 0 0 0 , 9 1 1 0 0 0 , 6 9 A N A N A N

E 0 6 D 0 1 1 F L F 0 0 . 1 0 0 0 , 0 4 1 0 0 0 , 3 1 1 5 8 . 0 0 0 , 9 1 1 0 0 0 , 6 9 A N A N A N

E 0 6 D 0 1 1 R L F 0 0 . 1 0 0 0 , 0 4 1 0 0 0 , 3 1 1 5 8 . 0 0 0 , 9 1 1 0 0 0 , 6 9 A N A N A N

E 0 6 D 0 4 1 R L F 5 2 . 1 0 0 0 , 5 7 1 0 0 0 , 2 4 1 0 1 . 1 0 0 0 , 4 5 1 0 0 0 , 5 2 1 A N A N A N

E 6 3 D 5 8 0 C F 5 7 . 0 0 0 , 5 0 1 0 0 0 , 5 8 5 6 . 0 0 0 , 1 9 0 0 0 , 4 7 5 5 . 0 0 0 , 7 7 0 0 0 , 3 6

E 6 3 D 5 8 0 H F 5 7 . 0 0 0 , 5 0 1 0 0 0 , 5 8 5 6 . 0 0 0 , 1 9 0 0 0 , 4 7 5 5 . 0 0 0 , 7 7 0 0 0 , 3 6

E 8 4 D 0 1 1 H F 0 0 . 1 0 0 0 , 0 4 1 0 0 0 , 3 1 1 5 8 . 0 0 0 , 9 1 1 0 0 0 , 6 9 A N A N A N

E 0 6 D 0 1 1 H F 0 0 . 1 0 0 0 , 0 4 1 0 0 0 , 3 1 1 5 8 . 0 0 0 , 9 1 1 0 0 0 , 6 9 A N A N A N

70 degree hollow cone spray pattern, 100 PSIG pump pressure Annual fuel utilization efficiency and heating capacity based upon U.S. Government standard test using D.O.E. isolated combustion rating procedure.

BURNER SETUP AND ADJUSTMENT PROCEDURES

1. PREPARATION STEPS

A. Calibrate and Check Operation of

All oil burner installations should be performed by a qualified installer in accordance with regulations of the National Fire Protection Standard for Oil-Burning Equipment, NFPA31 -- latest edition, and in complete compliance with all local codes and authorities having jurisdiction. A qualified installer is an individual or agency who is responsible for the installation and adjustments of the heating equipment and who is properly licensed and experienced to install oil-burning equipment in accordance with all codes and ordinances.

Measuring Equipment Follow manufacturer’s recommended procedures for calibration and equipment check out.

B. Prepare Heating Unit for Testing Drill two

1/4 inch holes in the flue between the heating plant and the barometric draft regulator. If space permits, the holes should be located in a straight section of the flue, at least two flue diameters from the elbow in the flue pipe and at least one diameter from the draft regulator. The purpose of the two holes in the flue pipe is to speed up testing and reduce instrument handling.

The proper installation and adjustment of any oil burner requires technical knowledge and the use of combustion test instruments. The following procedure must be followed to correctly adjust the burner to match the specific characteristics of the installation.

C. Clean and Seal Heating Plant Make sure the

burner blast tube, fan housing, and blower wheel are clear of dirt and lint. Seal any air leaks into the combustion chamber.

IMPORTANT

Always use combustion test instruments when making burner adjustments and draft gauge when setting the barometric damper. It is virtually impossible to make accurate and reliable adjustments using the “eyeball” method.

D. Nozzle Inspection Annual replacement of

nozzle is recommended. The nozzle size should match the design load . DO NOT OVERSIZE. (Determination of oversizing can be determined prior to your adjustment. If the firing rate should be reduced refer to Table 4.) Short cycles and low percent :on: time result in higher overall pollutant emissions and lower thermal efficiency. An in-line oil filter will reduce service problems due to nozzle clogging.

Check all oil lines and connections for leaks.

Connect pressure gauge by removing bleed fitting and screwing in pressure gauge. See Figure 9.

e zi S · e zi S · e zi S

Page 17 of the 321 Studios FH110D60E user manual — 3. COMBUSTION DIAGNOSIS
Page 17 · click to enlarge
Page 17

It should be located as close as possible to the oil burner. Care should be taken to prevent air leakage in the oil suction line. Use continuous runs of copper tubing and use minimum number of joints and fittings. Always use flare fittings.

K. Adjust Air Setting Examine the smoke - CO2

plot and, keeping in mind the curve of Figure 6, note the location of the “knee” where the smoke number begins to rise sharply. Noting the air gate position marks, adjust the air setting to a CO2 level 1/2 to 1 percent lower than the CO2 level at the “knee”. (This provides a tolerance against possible shifts in the setting over a period of time.) Do not increase the air setting any more than necessary on the lower portion of the curve below the “knee”

E. Adjustment of Electrodes Adjust ignition

electrodes as specified in Figure 10.

F. Operate Burner Operate burner, adjust air

setting for good flame by visual observation, and run for at least 10 minutes or until operation has stabilized.

The characteristic curve for some burners may not yield a distinct “knee” in the curve. In such cases, the setting should be made near the minimum smoke, (using judgement).

G. Check Burner Pressure Bleed air from

pump and nozzle piping. Check pump pressure and adjust to 100 psi, if necessary.

Lock the air adjustment and repeat draft, CO2 and smoke measurements to make sure the setting has not shifted.

2. COMBUSTION ADJUSTMENT STEPS

H. Set Draft Check the draft reading over the

fire with a draft gauge through a hole in the inspection door. The hole is above the flame level. Adjust the barometric draft regulator on the flue to give the over fire of -.02” W.C.

3. COMBUSTION DIAGNOSIS

L. Check Performance A well-matched and

well-tuned burner should be capable of operation with smoke not greater than No. 2 and at a CO2 level not less than 10%.

I. Check Smoke Readings After burner has been operating 5 or 10 minutes, make a smoke measurement in the flue, following the smoke tester instructions. Oily or yellow smoke spots on the filter paper are usually a sign of unburned fuel, indicating very poor combustion (and likely high emissions of carbon monoxide and unburned hydrocarbons.) This condition can sometimes be caused by too much air, or by other factors. If this condition cannot be corrected, major renovation or even burner replacement may be necessary.

If this cannot be reached, check the following:

1. Air leaks into the combustion chamber or heat exchanger can dilute the combustion gases and prevent normal CO 2 readings. Such leaks should be sealed with furnace cement or other high-temperature sealant.

To check for dilution by leakage, measure the CO2 at as high a point as possible over the fire, using a stainless steel tube inserted through the fire door sample hole (as described earlier for overfire draft measurements), and compare this with the CO2 measured in the flue. A difference of more than 1 percent CO2 between the flue and overfire reading usually indicates air entry through leaks that have not been properly sealed.

J. Develop Smoke - CO2 Curve Record measurements of smoke and CO2 from the flue. Then establish the smoke - CO2 curve by taking readings over a range of air settings, as shown in Figure 8.

To do this, start with the air gate set at nearly full open and then take smoke and CO2 readings at progressively lower air settings, as necessary to visualize the general shape of the curve. (The CO2 readings will increase as the air setting is decreased, unless combustion is incomplete.) Do not set the air gate to give a smoke reading above No. 4 or No. 5. Plot the points on graph paper, as in Figure 8. Usually 3 or 4 readings are enough to establish the curve.

Seal between the probe and inspection door sample hole during test. The inspection door hole should be sealed when not being used to avoid leakage of air through it. (See Step H.)

2. If the CO 2 level of 10% cannot be reached without exceeding No. 2 smoke, poor mixing of air and fuel is likely.

In adjusting each air setting, it is helpful to note the various positions of air gate at which measurements are made so that the final setting can be located quickly.

It may be necessary to replace the combustion head or try different settings.

Page 18 of the 321 Studios FH110D60E user manual — 4. CO 2 TEST
Page 18 · click to enlarge
Page 18

4. FINAL CHECKS

SHORT FORM ADJUSTMENT PROCEDURE

M. Measure Stack Temperature Operating the

unit at an excessive firing rate will generate more heat than the heat exchanger can utilize and result in unnecessary heat loss up the chimney. Other causes of excessive heat loss are badlysooted heat exchanger surfaces and excessive draft. The temperature of the flue gas provides an indication of these heat losses.

Some burner service organizations may wish to perform a shorter procedure for the adjustment of oil burners. The following is an example of such a short form prepared by the National Association of Oil Heat Service Managers.

1. SERVICE AND CLEAN BURNER Follow company procedure to complete the cleaning and servicing. Operate burner for ten minutes while tools are gathered and are cleaned.

Measure flue temperature by subtracting the room air temperature from the thermometer reading. Excessive stack loss is indicated of the net stack temperature during steady operation exceeds 600° F.

2, CHECK DRAFT Set draft regulator, if necessary. Regulator should be adjusted to achieve a -.02” W.C. over fire condition. The more restricted and lengthy the flue, the higher the draft necessary to obtain the accepted over fire conditions.

N. Check Ignition Check operation over repeated

cycles to insure prompt ignition on starting.

O. Check Pump Cutoff Slow pump cutoff at the

end of a firing cycle can cause smoke and other pollutant emissions. Check for prompt pump cutoff by observing flame or by testing smoke at shutdown. If poor cutoff is observed, make sure air is purged from the pump and nozzle line. Air trapped in the pump or nozzle line will expand when heated, thus causing oil to drip into the combustion chamber after shutdown. If poor cutoff persists, repair or replace pump. Also make sure the pump solenoid is working. If not replace.

3. SMOKE TEST

Follow the instructions of the manufacturer of the smoke tester and take a smoke sample. Adjust the air to obtain a preliminary reading of about No. 3 spot. Then readjust the air to obtain the lowest possible reading, but do not open the air adjustment more than absolutely necessary to obtain a trace or No. 0 spot.

4. CO 2 TEST

Check CO2 levels. This level should be between 10% and 12%.

Page 19 of the 321 Studios FH110D60E user manual — Technician's plotting area
Page 19 · click to enlarge
Page 19

FIGURE 8 TYPICAL SMOKE – CO 2 CHART WITH ADJUSTMENT RANGE

Air Settings Low High

CO Curve from plotted points

8 10 12 14 6

Percent CO in Flue Gas 2

Technician's plotting area

0 14 8 10 12 6 Percent CO in Flue Gas 2

Show 11 more labels / short text on this page
Bacharach Smoke Number · Plotted point · Normal adjustment · range · Tolerance · to "knee" · "Best" air setting · Plotted point · Plotted point · "Knee" · Bacharach Smoke Number
Page 20 of the 321 Studios FH110D60E user manual — Pressure Gauge
Page 20 · click to enlarge
Page 20

FIGURE 9 PRESSURE GAUGE CONNECTION TO BLEED PORT

Remove Bleed Port to attach pressure guage.

Pressure Gauge

Page 21 of the 321 Studios FH110D60E user manual — 1 e l z z o N
Page 21 · click to enlarge
Page 21

TABLE 5 CORRELATION OF PERCENT OF CO 2 , O 2

AND RESERVE AIR

n o b r a C

e d i x o i D n e g y x O ri A e v r e s e R

). x o r p p A (

4. 5 1 0 . 5 1 5 . 4 1
0. 0 6 . 0 2 . 1
0. 0 0 . 3 0 . 6
0. 4 1 5 . 3 1 0 . 3 1
0. 2 6 . 2 3 . 3
0. 0 1 0 . 5 1 0 . 0 2
5. 2 1 0 . 2 1 5 . 1 1
0. 4 6 . 4 3 . 5
0. 5 2 0 . 0 3 0 . 5 3
0. 1 1 5 . 0 1 0 . 0 1
0. 6 7 . 6 4 . 7
0. 0 4 0 . 5 4 0 . 0 5

TABLE 6 NO. 2 FUEL OIL EFFICIENCY CHART

(NET STACK TEMP. DEGREES F)

O % 2 0 0 2 0 5 2 0 0 3 0 5 3 0 0 4 0 5 4 0 0 5 0 5 5 0 0 6 0 5 6 0 0 7 0 5 7 0 0 8 O % 2

1 6 . 9 8 4 . 8 8 3 . 7 8 2 . 6 8 1 . 5 8 0 . 4 8 9 . 2 8 7 . 1 8 6 . 0 8 5 . 9 7 4 . 8 7 3 . 7 7 2 . 6 7 7 . 4 1

2 4 . 9 8 2 . 8 8 0 . 7 8 9 . 5 8 7 . 4 8 6 . 3 8 4 . 2 8 2 . 1 8 1 . 0 8 9 . 8 7 7 . 7 7 6 . 6 7 4 . 5 7 0 . 4 1

3 2 . 9 8 9 . 7 8 7 . 6 8 5 . 5 8 3 . 4 8 1 . 3 8 9 . 1 8 7 . 0 8 4 . 9 7 2 . 8 7 0 . 7 7 8 . 5 7 6 . 4 7 2 . 3 1

4 9 . 8 8 7 . 7 8 4 . 6 8 1 . 5 8 8 . 3 8 6 . 2 8 3 . 1 8 0 . 0 8 7 . 8 7 5 . 7 7 2 . 6 7 9 . 4 7 6 . 3 7 5 . 2 1

5 7 . 8 8 3 . 7 8 0 . 6 8 6 . 4 8 3 . 3 8 0 . 2 8 6 . 0 8 3 . 9 7 9 . 7 7 6 . 6 7 3 . 5 7 9 . 3 7 6 . 2 7 7 . 1 1

6 4 . 8 8 0 . 7 8 5 . 5 8 1 . 4 8 7 . 2 8 3 . 1 8 9 . 9 7 5 . 8 7 0 . 7 7 6 . 5 7 2 . 4 7 8 . 2 7 4 . 1 7 0 . 1 1

7 0 . 8 8 5 . 6 8 0 . 5 8 5 . 3 8 0 . 2 8 5 . 0 8 0 . 9 7 5 . 7 7 0 . 6 7 5 . 4 7 0 . 3 7 5 . 1 7 0 . 0 7 3 . 0 1

TABLE 7 RECOMMENDED START-UP SETTINGS

d e ll a t s n I y r o t c a F n o it p O d e ll a t s n I d l e i F

e c a n r u F

e l y t S r e n r u B

1 e l z z o N

d n a B

r e tt u h S

1 e l z z o N

d n a B

r e tt u h S

1 e l z z o N

d n a B

r e tt u h S

. o N l e d o M

. o N tr a P

g n itt e S

g n itt e S

g n itt e S

g n itt e S

g n itt e S

g n itt e S

E 6 3 D 5 8 0 H F 6 2 0 - 0 2 0 9 / G F A 5 7 . 0 6 5 6 . 0 5 5 5 . 0 5

E 8 4 D 0 1 1 H F 7 2 0 - 0 2 0 9 / G F A 0 0 . 1 2 0 1 5 8 . 0 8 A N A N A N

E 0 6 D 0 1 1 H F 7 2 0 - 0 2 0 9 / G F A 0 0 . 1 2 0 1 5 8 . 0 8 A N A N A N

E 6 3 D 5 8 0 F L F 6 2 0 - 0 2 0 9 / G F A 5 7 . 0 6 5 6 . 0 5 5 5 . 0 5

E 8 4 D 0 1 1 F L F

E 0 6 D 0 1 1 F L F 7 2 0 - 0 2 0 9 / G F A 0 0 . 1 2 0 1 5 8 . 0 8 A N A N A N

E 6 3 D 5 8 0 R L F 1 3 0 - 0 2 0 9 / G F A 5 7 . 0 6 5 6 . 0 5 5 5 . 0 5

E 8 4 D 0 1 1 R L F

E 0 6 D 0 1 1 R L F 2 3 0 - 0 2 0 9 / G F A 0 0 . 1 2 0 1 5 8 . 0 8 A N A N A N

E 0 6 D 0 4 1 R L F 3 3 0 - 0 2 0 9 / G F A 5 2 . 1 0 8 0 1 . 1 0 6 A N A N A N

E 6 3 D 5 8 0 C F 6 2 0 - 0 2 0 9 / G F A 5 7 . 0 6 5 6 . 0 5 5 5 . 0 5

70 degree hollow cone spray pattern, 100 PSIG pump pressure

Show 6 more labels / short text on this page
ri A · ri A · ri A · ri A · ri A · ri A
Page 22 of the 321 Studios FH110D60E user manual — FIGURE 10 ELECTRODE ADJUSTMENTS
Page 22 · click to enlarge
Page 22

SPACING OF ELECTRODES

COMBUSTION AIR REQUIREMENTS

The electrodes should be spaced 5/32” apart. They should extend 1/16” beyond the end and 5/16” above the center of the nozzle tip as shown in Figure 10.

This furnace must be installed in a location where a sufficient supply of combustion air is available for the complete combustion of the fuel oil. Keep in mind that a certain amount of excess air is required as well to ensure complete combustion of the fuel oil.

GUN ASSEMBLY ADJUSTMENT

The gun assembly can be adjusted in the slot inside of fan housing by loosening screw holding slot cover in position. Nozzle tip should ordinarily be located 1-1/8” behind the front face of the cone.

When structures are constructed too tightly to supply sufficient combustion air, air from outside the structure is required to be brought in directly to the furnace. This furnace has been conveniently designed to accept a combustion air boot which is attached directly to the outdoors by means of a 4” pipe. This pipe can be rigid or flexible, but it is recommended that a metallic material be used. Refer to Figure 11. The air boot used for this design is a Field Controls model number CAS-2B-90E that can be purchased through your local distributor. Follow all installation procedures as specified in the instructions packaged with the air boot kit.

REMOVING GUN ASSEMBLY

Disconnect the oil line at the fan housing and remove lock nuts on copper tube fitting. Loosen igniter hold down clamps, then swing igniter up and backward. Gun assembly can now be removed through this opening.

FIGURE 10 ELECTRODE ADJUSTMENTS

5/32 GAP

1/16 NOZZLE

1-1/8 · 5/16

Page 23 of the 321 Studios FH110D60E user manual — FIGURE 11 COMBINATION AIR BOOT ASSEMBLY
Page 23 · click to enlarge
Page 23

FIGURE 11 COMBINATION AIR BOOT ASSEMBLY

COMBUSTION

AIR BOOT ASSEMBLY

USE THIS KNOCKOUT FOR OIL LINE

INTAKE

AIR TUBE

BURNER ASSEMBLY

REMOVE PUMP TO ASSEMBLE INNER AIR BOOT

REMOVE KNOCKOUT IN LEFT SIDE

INSERT OUTER AIR BOOT AND SECURE FLANGE TO UNIT

MAKE ALL SETTINGS ACCORDING TO MANUAL FOR AIR BOOT.

Page 24 of the 321 Studios FH110D60E user manual — FIGURE 12 APPLIANCES LOCATED
Page 24 · click to enlarge
Page 24

APPLIANCES LOCATED IN CONFINED SPACES

TABLE 8 SQUARE FEET REQUIRED TO QUALIFY AS UNCONFINED SPACE

In unconfined spaces in buildings, infiltration may be adequate to provide air for combustion, ventilation, and dilution of flue gases. However, in buildings of unusually tight construction, additional air shall be provided using the method described under “All Air From Outdoors” in Figure 13.

e c a p S d e n if n o c n U

l a t o T

n I a e r A m u m i n i M

H U T B

t e e F e r a u q S

t u p n I

t h g i e H g n ili e C ' 8

An unconfined space (such as an open basement) must have a minimum volume of 50 cubic feet per 1,000 BTUH of total of all appliances in area. Adjoining rooms may be counted as one area only if there are not doors between the rooms.

0 0 0 , 0 6 0 0 0 , 0 8 5 7 3 0 0 5

0 0 0 , 5 8 0 0 0 , 5 0 1 1 3 5 6 5 6

0 0 0 , 5 1 1 0 0 0 , 0 2 1 9 1 7 0 5 7

Shown in Table 8 are the required minimum areas in square feet to qualify as an unconfined space for various total BTUH input ratings. The table is based on a room(s) with 8 foot ceiling heights.

0 0 0 , 0 4 1 0 0 0 , 5 4 1 5 7 8 6 0 9

0 0 0 , 0 6 1 0 0 0 , 0 0 2 0 0 0 1 0 5 2 1

If the unconfined space is within a building having insufficient air because of tight construction, the air for combustion and ventilation shall be obtained from outdoors or from spaces freely communicating with the outdoors. Under these conditions a permanent opening or openings have a total free area of not less than one square inch per 5,000 BTU per hour (28 square inches per hour ) of total input rating of all appliances shall be provided. For combustion air options see Page 20, “Combustion Air Requirements”.

ALL AIR FROM INSIDE BUILDING

The confined space shall be provided with two permanent openings, one near the top of the enclosure and one near the bottom. Each opening shall have a free area of not less than one square inch per 1,000 BTU per hour (140 square inches per gallon per hour) of the total input rating of all appliances in the enclosure freely communicating with interior areas having in turn adequate infiltration from the outside. (See Figure 12.) Also see Table 9 on the following page for specific ventilation opening requirements for the furnace only.

FIGURE 12 APPLIANCES LOCATED

IN CONFINED SPACES ALL AIR FROM INSIDE THE BUILDING

The flow of combustion and ventilating air must not be obstructed from reaching the furnace.

not less than one square inch per 1,000 BTU per hour (140 square inches per gallon per hour) of the total input rating of all appliances in the enclosure.

Page 25 of the 321 Studios FH110D60E user manual — FIGURE 13 APPLIANCES LOCATED IN CONFINED SPACES
Page 25 · click to enlarge
Page 25

TABLE 9 MINIMUM VENTILATION OPENINGS

ALL VENTILATION AIR FROM OUTDOORS

A. The confined space shall be provided with two

321 Studios FH110D60E — TABLE 9 MINIMUM VENTILATION OPENINGS diagram (page 25)
Fig. 11

d e d n e m m o c e R

permanent openings, one in or near the top of the enclosure and one in or near the bottom. The openings shall communicate directly, or by means of ducts with outdoors or to such spaces (crawl or attic) that freely communicate with outdoors. (See Figures 13, 14, & 15.)

n o it a lit n e V . n i M

) d e ri u q e R 2 (

h c n I e r a u q S

e zi S . n I . q S

E 6 3 D 5 8 0 H F 0 4 2 6 1 x 8 8 2 1

E 8 4 D 0 1 1 H F 0 8 2 8 1 x 9 2 6 1

B. When directly communicating with outdoors or by

E 0 6 D 0 1 1 H F 0 8 2 8 1 x 9 2 6 1

means of vertical ducts, each opening shall have a free area of not less than one square inch per 4,000 BTU per hour (35 square inches per gallon per hour) of total input rating of all appliances in the enclosures. If horizontal ducts are used, each opening shall have a free area of not less than one square inch per 2,000 BTU per hour (70 square inches per gallon per hour) of total input of all appliances in the enclosure.

E 6 3 D 5 8 0 F L F 0 9 2 9 1 x 8 2 5 1

E 6 3 D 5 8 0 R L F 0 9 2 9 1 x 8 2 5 1

E 8 4 D 0 1 1 F L F

E 0 6 D 0 1 1 F L F 0 4 3 9 1 x 9 1 7 1

E 8 4 D 0 1 1 R L F

E 0 6 D 0 1 1 R L F 0 4 3 9 1 x 9 1 7 1

E 0 6 D 0 4 1 R L F 0 6 3 9 1 x 5 . 9 0 8 1

E 6 3 D 5 8 0 C F 0 4 2 6 1 x 8 8 2 1

FIGURE 13 APPLIANCES LOCATED IN CONFINED SPACES

ALL AIR FROM OUTDOORS

321 Studios FH110D60E — FIGURE 13 APPLIANCES LOCATED IN CONFINED SPACES diagram (page 25)
Fig. 12

free area of not less than one square inch per 2,000 BTU per hour (70 square inches per gallon per hour) of the total input rating of all appliances in the enclosure.

Page 26 of the 321 Studios FH110D60E user manual — FIGURE 15 APPLIANCES LOCATED IN CONFINED SPACES
Page 26 · click to enlarge
Page 26

FIGURE 14 APPLIANCES LOCATED IN CONFINED SPACES ALL AIR FROM OUTDOORS THROUGH VENTILATED ATTIC

321 Studios FH110D60E — FIGURE 4 TYPICAL UNIT SETUP diagram (page 26)
Fig. 13

shall each have a free area of not less than one square inch per 4,000 BTU per hour (35 square inches per gallon per hour) of the total input rating of all appliances in the enclosure.

FIGURE 15 APPLIANCES LOCATED IN CONFINED SPACES

ALL AIR FROM OUTDOORS INLET AIR FROM VENTILATED CRAWL SPACE AND OUTLET AIR TO VENTILATED ATTIC

321 Studios FH110D60E — FIGURE 15 APPLIANCES LOCATED IN CONFINED SPACES diagram (page 26)
Fig. 14

shall each have a free area of not less than one square inch per 4,000 BTU per hour (35 square inches per gallon per hour) of the total input rating of appliances in the enclosure.

Page 27 of the 321 Studios FH110D60E user manual — VERTICAL VENTING
Page 27 · click to enlarge
Page 27

LOUVERS AND GRILLES

A barometric damper is supplied with the furnace and must be installed in the flue pipe observing the instructions packaged with the damper control. The barometric damper opening must be located in the same atmospheric pressure zone as the combustion air inlet to the furnace. The furnace must not be vented into the same chimney with any solid fuel burning appliance such as a wood burner or pellet burner. Masonry chimneys must be lined with a listed system or other approved material that will resist corrosion, softening or cracking from flue gas temperatures up to 1800° F. See Standard for Installation of Oil Burning Equipment NFPA31 latest edition and Standard for Chimneys NFPA211 latest edition for additional information.

In calculating free area for ventilation and combustion air requirements, consideration shall be given to the blocking effect of louvers, grilles, or screens protecting openings. Screens used shall not be smaller than 1/4 inch (6.3 mm) mesh and shall be readily accessible for cleaning. If the free area through a design of louver or grille is known, it shall be used in calculating the size opening required to provide the free area specified. If the design and free area is not known, it may be assumed that wood louvers will have 30-35 percent free area and metal louvers and grilles will have 60-75 percent free area.

VENTING OPTIONS

HORIZONTAL VENTING

This furnace is designed to be vented conventionally into a vertical chimney or horizontally through a side wall with an optional Field Controls side wall power venting system.

This furnace is designed to be horizontally vented through a side wall with an optional side wall power vent. The recommended side wall venter is the Field Controls model number SWG-4HDS for 085 and 110 models, and SWG-5S for 140 models only. This venter can be purchased through your local distributor. Follow all installation instructions packaged with the venter system.

Note that the FH, FC and FLF series furnaces have been designed to allow for bringing the vent system through the cabinet side for increased venting flexibility. To take advantage of this feature, simply remove the desired knockout from either side or top of unit and rotate flue box accordingly by removing four (4) screws under cleanout plate as shown in Figure 4. Make sure smoke pipe gasket is in place before reinstalling flue box screws.

THERMOSTAT

These furnaces are designed to be controlled with any 24V heating or heating/cooling thermostat. The heat/cool thermostats must be designed for independent heat/cool transformer circuits to assure that the 24V transformer built into the oil primary control does not conflict with the main furnace 24V transformer. The heat anticipator should be set at 0.20A. This is a nominal setting. The thermostat circuit should be checked to verify setting.

VERTICAL VENTING

If the unit is to be vertically vented make sure the flue pipe from the furnace to the chimney is the same size diameter as the flue outlet of the furnace which is 6”. The flue pipe must have no reductions in diameter, be made of a corrosion-resistant material having an upward pitch of 1/4” for every foot of horizontal run, and be made of material capable of handling temperatures up to 1800° F.

Page 28 of the 321 Studios FH110D60E user manual — TABLE 10 TEMPERATURE RISE RANGES, LIMIT CONTROL SETTINGS,
Page 28 · click to enlarge
Page 28

TABLE 10 TEMPERATURE RISE RANGES, LIMIT CONTROL SETTINGS,

AND HEATING BLOWER SPEEDS

m u m i x a M

1 e l z z o N s e g n a R e s i R

ri A t e lt u O

r e w o l B g n it a e H

l e d o M

. p m e T

d e e p S

0 0 1 - 0 7 0 0 1 - 0 7 0 9 - 0 6

0 0 2 0 0 2 0 0 2

E 6 3 D 5 8 0 H F

E 8 4 D 0 1 1 H F 5 8 .

0 0 . 1 0 0 1 - 0 7 0 9 - 0 6 0 0 2 0 0 2 w o L

w o L d e M

E 0 6 D 0 1 1 H F 5 8 .

0 0 . 1 0 9 - 0 6 0 9 - 0 6 0 0 2 0 0 2 w o L

w o L d e M

0 9 - 0 6 0 9 - 0 6 0 9 - 0 6

0 0 2 0 0 2 0 0 2

E 6 3 D 5 8 0 F L F

E 8 4 D 0 1 1 F L F 5 8 .

0 0 . 1 0 9 - 0 6 0 9 - 0 6 0 0 2 0 0 2 w o L d e M

h g i H d e M

E 0 6 D 0 1 1 F L F 5 8 .

0 0 . 1 0 9 - 0 6 0 9 - 0 6 0 0 2 0 0 2 w o L d e M

h g i H d e M

0 9 - 0 6 0 9 - 0 6 0 9 - 0 6

0 0 2 0 0 2 0 0 2

E 6 3 D 5 8 0 R L F

E 8 4 D 0 1 1 R L F 5 8 .

0 0 . 1 0 9 - 0 6 0 9 - 0 6 0 0 2 0 0 2 w o L d e M

h g i H d e M

E 0 6 D 0 1 1 R L F 5 8 .

0 0 . 1 0 9 - 0 6 0 9 - 0 6 0 0 2 0 0 2 w o L d e M

h g i H d e M

E 0 6 D 0 4 1 R L F 0 1 . 1 5 2 . 1 0 9 - 0 6 0 9 - 0 6 0 0 2 0 0 2 w o L d e M

h g i H d e M

0 0 1 - 0 7 0 0 1 - 0 7 0 9 - 0 6

0 0 2 0 0 2 0 0 2

E 6 3 D 5 8 0 C F

70 degree hollow cone spray pattern, 100 PSIG pump pressure

Show 12 more labels / short text on this page
w o L · w o L · d e M · w o L · w o L · d e M · w o L · w o L · d e M · w o L · w o L · d e M
Page 29 of the 321 Studios FH110D60E user manual — FIGURE 16 TYPICAL INSTALLATION OF FR26 AND
Page 29 · click to enlarge
Page 29

AIR FILTERS

Only Lo-Boy models are shipped with air filters. Filter kits are available from your local distributor for Upflow and Counterflow models. Knockouts are provided in the sides of the FH series models to facilitate the cutting of the return openings.

TABLE 11 FILTER SIZES FOR OIL FURNACES

321 Studios FH110D60E — TABLE 11 FILTER SIZES FOR OIL FURNACES diagram (page 29)
Fig. 15

E 6 3 D 5 8 0 H F

y o B -i H ) 1 ( 1 x 5 2 x 6 1

The upflow filter kit part numbers are FR23 for a 16x25x1 filter size and FR24 for a 20x25x1 filter size. These filter kits come complete with the filter and all necessary brackets for installing on the furnace. Each comes with a washable aluminum mesh filter. When installing a five ton AC unit on the furnace, one FR24 or Two FR23 must be used due to the high airflow requirements. It is important to note that a minimum of one inch spacing is required between the filter and the unit side. Do not exceed 400 fpm for fiberglass (disposable) type filters and 575 fpm for washable type filters. See Figure 16.

E 8 4 D 0 1 1 H F

y o B -i H ) 1 ( 1 x 5 2 x 6 1

E 0 6 D 0 1 1 H F

y o B -i H ) 1 ( 1 x 5 2 x 0 2

E 6 3 D 5 8 0 F L F

E 6 3 D 5 8 0 R L F

) 1 ( 1 x 0 2 x 6 1

E 8 4 D 0 1 1 F L F

E 8 4 D 0 1 1 R L F

E 0 6 D 0 1 1 F L F

) 1 ( 1 x 0 2 x 0 2

E 0 6 D 0 1 1 R L F

The counterflow filter kit part number FR25 comes with two washable filters. If not installing the FR25 kit remember not to exceed 400 fpm for fiberglass (disposable) type filters and 575 for washable type filters. See Figure 17.

E 0 6 D 0 4 1 R L F

y o B - o L ) 1 ( 1 x 5 2 x 0 2

E 6 3 D 5 8 0 C F

w olfr e tn u o C ) 2 ( 1 x 0 2 x 6 1

See Table 11 for filter sizes and quantities.

FIGURE 16 TYPICAL INSTALLATION OF FR26 AND

FIGURE 17 TYPICAL INSTALLATION OF FR25

FR27 FILTER RACKS

FILTER KIT

321 Studios FH110D60E — FIGURE 16 TYPICAL INSTALLATION OF FR26 AND diagram (page 29)
Fig. 16
Page 30 of the 321 Studios FH110D60E user manual — REPLACEMENT
Page 30 · click to enlarge
Page 30

LO-BOY MODELS – FILTER LOCATIONS

Lo-boy models have the filter installed in the return air cabinet section of the furnace. It is accessible from the rear of the furnace by removing the blower/filter access door. The electrical switch should be turned “off” prior to removing the access door. Refer to Figure 18 below.

FIGURE 18 FILTER INSTALLATION – LO-BOY MODELS

LOWBOY FILTER

UNIT FILTER SIZE FLF/FLR085 16 x 20 x1 FLF/FLR110 20 x 20 x1 FLR140 20 x 25 x 1

REPLACEMENT

STEP 3: SLIDE FILTER OUT TOWARDS BLOWER

DOOR

STEP 2: REMOVE BLOWER DOOR

STEP 1: UNFASTEN SWELL LATCHES BY PULLING

BY PULLING OUT ON SWELL LATCHES AND

HANDLES OUTWARD

TILTING OUTWARDS

Page 31 of the 321 Studios FH110D60E user manual — SERVICE HINTS
Page 31 · click to enlarge
Page 31

MAINTENANCE

LUBRICATION

B. Ignition Failure – Test by closing oil supply

while burner is off. Run through starting procedure. The primary control will attempt three trials for ignition. After three attempts, the control will lockout. C. Power Failure – Turn off power supply

No lubrication is required for either the burner or the blower motor. Both are permanently lubricated.

INSPECT AIR FILTER

Replace filters before each heating season begins. It is recommended that filters also be replaced at least twice during the heating season.

while burner is on. When burner goes out, restore power and burner will restart. D. If operation is not as described, check wiring

and installation first. If trouble appears to be in the control circuit, replace the flame detector. If trouble still persists, refer to “Common Causes of Trouble” section on page 28.

Be sure the new filters are set securely in the filter rack so there can be minimal leakage around them.

FINAL INSPECTION AND TEST

Final inspection and test of an installation shall be made to determine that the work has been done in full accordance with regulations and according to the highest standards for safety, performance and appearance. Such an inspection and test should indicate the following as a minimum:

SERVICE HINTS

Preventive maintenance is the best way to avoid unnecessary expense, inconvenience, and retain operating efficiency of your furnace. It is advisable to have your heating system and burner inspected at periodic intervals by a qualified serviceman. If trouble develops, follow these simple checks before calling the serviceman.

1. Determine that all parts of the oil storage and circulating system, including tank, piping and burner, are free from oil leaks. Be sure that no oil discharges from the nozzle when burner is not operating. 2. Be sure that the suction line and pump have been entirely vented of air so that the burner has instantaneous oil shutoff at the nozzle and so that the pump operates without an air noise. 3. Check the flame adjustment to determine that the flame is clear, quiet, free of odor and oil nozzle is of proper size for the furnace. 4. Test operation of burner by operating the thermostat. First, set the thermostat above room temperature. Burner should start. Second, set thermostat below room temperature. Burner will stop. 5. Check operation of burner primary control in accordance with manufacturer’s instructions included with the control. Following is the method we recommend in checking the safety switch in this primary control. A. Flame Failure – Simulate by shutting off oil

1. Make sure there is oil in tank and valve is open. 2. Make sure thermostat is set above room temperature. 3. Make sure electrical supply to furnace is on and fuses are not blown or circuit breakers tripped. 4. Reset safety switch of burner primary control. CAUTION

Reset three (3) times only. More than three resets can cause excessive oil to be pumped into combustion chamber which could result in explosion upon ignition.

5. Press thermal protector button of burner motor. 6. Make sure air filters are in place and are clean. 7. Make sure all air openings in furnace, all ventilation and combustion air openings, all return air grilles, and all warm air registers are unobstructed and open.

supply manual valve while burner is on. Within 9 seconds the control will shut the burner down and flash a diagnostic code of 1/2 second on / 1/2 second off. Ignition and motor stop and oil valve closes

Page 32 of the 321 Studios FH110D60E user manual — STEP 2: LOOSEN (3) BOLTS ENOUGH TO ROTATE
Page 32 · click to enlarge
Page 32

COMBINATION COMBUSTION CHAMBER/BURNER MOUNTING SYSTEM

WARNING

The furnace has been designed with a combustion chamber mounting system that enables service personnel to remove the combustion chamber, its mounting system, and burner assembly as one unit for inspection and/or service on the bench. It has also been designed to remove the burner assembly independently from the mounting system to perform basic annual service and inspection. The mounting system is completely adjustable so exact alignment between the burner tube and combustion chamber may be assured prior to installation into the furnace. See Figure 19 and 20.

The procedures described in Figures 19 and 20 should be conducted only by a qualified service technician.

Improper servicing could cause electric shock hazard, fires or explosion resulting in damage, injury or death.

FIGURE 19 REMOVAL OF BURNER ONLY

BURNER REMOVAL

DANGER !

INSTRUCTIONS

*ELECTRICAL SHOCK HAZARD *DISCONNECT POWER BEFORE SERVICING.

STEP 2: LOOSEN (3) BOLTS ENOUGH TO ROTATE

BURNER ASSEMBLY.

3. ROTATE BURNER COUNTER-CLOCKWISE STEP 4: PULL BURNER STRAIGHT OUT TO PREVENT DAMAGE TO CHAMBER DURING REMOVAL. MIS-1834
1. DISCONNECT "T-T" WIRES, POWER CONNECTIONS, AIR BOOT (OPTIONAL) AND OIL LINES TO BURNER.
Page 33 of the 321 Studios FH110D60E user manual — FIGURE 20 REMOVAL OF ENTIRE COMBUSTION CHAMBER MOUNTING SYSTEM
Page 33 · click to enlarge
Page 33

TO REMOVE BURNER ONLY

TO REMOVE THE ENTIRE COMBUSTION CHAMBER MOUNTING SYSTEM

Disconnect fuel line, power cord and wires from T, T on primary control. Loosen (3) 1/4 inch bolts securing burner mounting flange. Twist burner counterclockwise and pull straight back away from the furnace. (See Figure 19.)

Disconnect fuel line, power cord and wires from T, T on primary control. Remove (6) 5/16 inch bolts from around front plate. Next remove (2) 5/16 inch nuts from upper right and left hand corners of the front plate. Pull entire assembly straight back away from furnace. BE CAREFUL NOT TO TIP ASSEMBLY UP OR DOWN AS IT MAY DAMAGE THE COMBUSTION CHAMBER. (See Figure 20.)

FIGURE 20 REMOVAL OF ENTIRE COMBUSTION CHAMBER MOUNTING SYSTEM

321 Studios FH110D60E — FIGURE 20 REMOVAL OF ENTIRE COMBUSTION CHAMBER MOUNTING SYSTEM diagram (page 33)
Fig. 17
2. REMOVE (6) BOLTS AROUND PERIMETER OF BURNER PLATE STEP 4: PULL BURNER ASSEMBLY STRAIGHT OUT TO PREVENT DAMAGE TO CHAMBER DURING REMOVAL. MIS-1837
1. DISCONNECT "T-T" WIRES, POWER CONNECTIONS, AIR BOOT (OPTIONAL) AND OIL LINES TO BURNER.
Page 34 of the 321 Studios FH110D60E user manual — CHATTERING SOUND OR HIGH PITCH NOISE
Page 34 · click to enlarge
Page 34

COMMON CAUSES OF TROUBLE

PUMP SQUEALS OR CHATTERS

CAUTION

This may be caused by air in pipes. Check all joints in the oil supply pipe for leaks. Check strainer in pump; if dirty, clean.

To avoid accidents, always open main switch (OFF position) when servicing the burner.

INSUFFICIENT HEAT

Check limit control setting. It may be that flame is not allowed to stay on long enough to generate sufficient heat in furnace to heat the house properly. If the proper size furnace has been selected according to house requirements and satisfactory heat is not obtained, recheck the heating plant for size and capacity in relation to house. Check for clogged filters.

BURNER WILL NOT PRODUCE FLAME

Check oil level gauge to see that there is sufficient oil in tank or tanks. Check the burner mounted relay control. Do not adjust this control.

Check position of electrodes – incorrect position will cause slow or delayed ignition. Clean electrodes and nozzle. Check and clean strainer in pump. If oil line filter is used, check filter condition.

Check and make sure the heat anticipator on the thermostat is set correctly.

CARE OF FINISH

If burner runs but there is no flame the fuel pump may be air bound. Follow instructions for bleeding fuel pump.

This furnace cabinet is made with a very durable and corrosion resistant finish. With normal cleaning it will last for many years.

Check and make sure the solenoid valve on the oil pump is being energized and opening.

WARNING

BURNER STARTS OR STOPS TOO OFTEN

Check heat anticipator setting on thermostat.

Under no circumstance should a soot deterioration device be used in the combustion chamber. These products known as “soot busters” or “soot sticks” are comprised of chemicals that burn at very high temperatures which may exceed the temperature rating of the combustion chamber material.

NOZZLE PRODUCES A STRINGY FLAME

Worn tangential grooves in nozzle. Replace nozzle.

BASEMENT TANK HUM

Occasionally with a two-pipe installation there may be a low return line hum. Eliminate hum by installing a special anti-hum valve in the return line near pump.

Use of these products are detrimental to the life expectancy of the combustion chamber and will destroy the chamber. Refer to the “Cleaning of Furnace” section for proper cleaning methods.

HEAVY FIRE OR PULSATING FLAME.

These may occur after burner starts. It may be caused by a slight oil leak in the fuel pump and cannot be corrected except by replacing the pump. This happens only when the burner is started.

CLEANING OF THE HEAT EXCHANGER

CHATTERING SOUND OR HIGH PITCH NOISE

All of these units have four clean out plugs for easy cleaning of the heat exchanger. They are accessible from the front and back of these units by removing the clean out access cover in the burner compartment and at the back of unit. The furnace should be checked annually by a qualified service technician.

This noise from motor can usually be traced to where a conduit or BX cable is fixed rigidly or attached to some part of the building. Relieving this strain may eliminate noise.

Page 35 of the 321 Studios FH110D60E user manual — CHART 3 FH110D60E DATA
Page 35 · click to enlarge
Page 35

BLOWER SYSTEM RESISTANCE CHARTS

CHART 1 FH085D36E DATA

CHART 4 FLF/FLR085D36E DATA

d e e p S r e w o l B c it a t S r e w o l B

d e e p S r e w o l B c it a t S r e w o l B

w o L 0 1 . 5 1 . 3 2 . 0 3 .

w o L 7 0 . 3 1 . 9 1 . 5 2 .

m u i d e M 6 1 . 4 2 . 4 3 . 3 4 .

m u i d e M 5 1 . 4 2 . 3 3 . 1 4 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

CHART 5 FLF/FLR110D48E DATA

CHART 2 FH110D48E DATA

d e e p S r e w o l B c it a t S r e w o l B

d e e p S r e w o l B c it a t S r e w o l B

w o L 3 0 . 8 0 . 3 1 . 8 1 .

w o L 5 0 . 9 0 . 5 1 . 0 2 .

w o L m u i d e M 9 0 . 6 1 . 3 2 . 2 3 .

w o L m u i d e M 9 0 . 6 1 . 3 2 . 1 3 .

h g i H m u i d e M 6 1 . 5 2 . 4 3 . 4 4 .

h g i H m u i d e M 5 1 . 4 2 . 4 3 . 2 4 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

CHART 3 FH110D60E DATA

CHART 6 FLF/FLR110D60E DATA

d e e p S r e w o l B c it a t S r e w o l B

d e e p S r e w o l B c it a t S r e w o l B

w o L 6 0 . 2 1 . 7 1 . 1 2 .

w o L 8 0 . 2 1 . 7 1 . 1 2 .

w o L m u i d e M 0 1 . 7 1 . 3 2 . 0 3 .

w o L m u i d e M 0 1 . 6 1 . 2 2 . 8 2 .

h g i H m u i d e M 4 1 . 1 2 . 1 3 . 8 3 .

h g i H m u i d e M 3 1 . 1 2 . 9 2 . 6 3 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

Page 36 of the 321 Studios FH110D60E user manual — CHART 7 FLR140D60E DATA
Page 36 · click to enlarge
Page 36

CHART 7 FLR140D60E DATA

CHART 8 FC085D36E DATA

d e e p S r e w o l B c it a t S r e w o l B

d e e p S r e w o l B c it a t S r e w o l B

w o L 5 0 . 4 1 . 7 1 . 4 2 .

w o L 8 0 . 4 1 . 0 2 . 6 2 .

w o L m u i d e M 8 0 . 7 1 . 2 2 . 0 3 .

m u i d e M 6 1 . 4 2 . 6 3 . 2 4 .

h g i H m u i d e M 1 1 . 0 2 . 7 2 . 5 3 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

h g i H 0 2 . 0 3 . 0 4 . 0 5 .

Page 37 of the 321 Studios FH110D60E user manual — BLOWER ASSEMBLY
Page 37 · click to enlarge
Page 37

FH SERIES WIRING DIAGRAM

321 Studios FH110D60E — FH SERIES WIRING DIAGRAM diagram (page 37)
Fig. 18

UNIT

NOTES

PURPLE PURPLE

PRIMARY

CONTROL PANEL HEAT EXCHANGER AREA

IF PRIMARY LIMIT WIRES ARE TO BE REPLACED, USE WIRE WITH INSUL. TEMP. RATING OF 200°C.

LIMIT CONTROL BACKUP

BURNER ASS'Y

LIMIT

HEATING SPEED CONNECTION POINT.

T T

COOLING SPEED CONNECTION POINT.

VALVE

OIL VALVE

ONLY ONE HEATING AND COOLING SPEED CAN BE CONNECTED. ALL OTHER TAPS CONNECT TO "SPARE" TERMINALS.

BURNER MOTOR

BURNER MOTOR

BLACK

BLACK

IGNITOR

IGNITOR

WHITE

BLACK

BLACK

BLACK

DASHED LINES REPRESENT FIELD WIRING.

CAD CELL

CAD CELL

DANGER !

*ELECTRICAL SHOCK HAZARD *DISCONNECT POWER BEFORE SERVICING.

BLACK

HOT

WHITE GREEN

GROUND NEUTRAL

PLUG #1 PLUG #2

2 1 1 2 3 4 5 6 7 8 9

WARNING !

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THIS APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL HAVING A TEMP. RATING OF AT LEAST 105°C EXCEPT PRIMARY LIMIT WIRES. SEE NOTE "1".

PURPLE

PURPLE

BLACK BLACK

BLACK

BLACK

GREEN

DOOR SWITCH

WHITE

GREEN

Y C W Rh Y G Rc

BLUE

240 210 180 150 R W G Y C

SEC2

SEC1

COND.

UNIT

THERMOSTAT

BLOWER CONTROL T T

24V. CONN.

T87F/Q539A1220 OR EQUIVELANT

TRANSFORMER

HUM

HEAT

COOL

COM

SPR1

SPR2

SPR3

OPTIONAL AIR COND. SETTINGS

OPTIONAL AIR COND. SETTINGS

EAC

A/C TONS UNIT CFM @ .50 WC COOLING BLOWER

A/C TONS UNIT CFM @ .50 WC COOLING BLOWER

NOM.

NOM.

120V COM

SPEED (COLOR)

SPEED (COLOR)

2 LOW (RED) 730 2 1/2 MED (BLUE) 900 3 HIGH (BLACK) 1160 2 1/2 LOW (RED) 1020 3 MED-LOW (ORANGE) 1280 3 1/2 MED-HIGH (BLUE) 1495 4 HIGH (BLACK) 1640 3 LOW (RED) 1300 3 1/2 MED-LOW (ORANGE) 1460 4 MID-HIGH (BLUE) 1660 5 HIGH (BLACK) 1970

2 LOW (RED) 730 2 1/2 MED (BLUE) 900 3 HIGH (BLACK) 1160 2 1/2 LOW (RED) 1020 3 MED-LOW (ORANGE) 1280 3 1/2 MED-HIGH (BLUE) 1495 4 HIGH (BLACK) 1640 3 LOW (RED) 1300 3 1/2 MED-LOW (ORANGE) 1460 4 MID-HIGH (BLUE) 1660 5 HIGH (BLACK) 1970

FH085D36E

FH085D36E

BLACK

2 WHITE WHITE

SEE CHART FOR HEATING AND COOLING WIRE COLORS

FH110D48E

FH110D48E

WHITE

PLUG #3

FH110D60E

FH110D60E

1 2 3 4 5

BLOWER CAPACITOR

WHITE RED ORANGE BLUE

FACTORY SETTINGS INPUT

FACTORY SETTINGS INPUT

LOW VOLTAGE

BLACK

TEMP.

TEMP.

GPH UNIT COOLING BLOWER

GPH UNIT COOLING BLOWER

RATE

RATE

HEATING BLOWER

HEATING BLOWER

RISE RANGE

RISE RANGE

RETURN AREA

SPEED (COLOR)

SPEED (COLOR)

SPEED (COLOR)

SPEED (COLOR)

0.55 LOW (RED) 70°-100° 0.65 LOW (RED) 70°-100° 0.75 MED (BLUE) 60°-90° 0.85 LOW (RED) 70°-100° 1 MED-LOW (ORANGE) 60°-90° 0.85 LOW (RED) 60°-90° 1 MED-LOW (ORANGE) 60°-90°

0.55 LOW (RED) 70°-100° 0.65 LOW (RED) 70°-100° 0.75 MED (BLUE) 60°-90° 0.85 LOW (RED) 70°-100° 1 MED-LOW (ORANGE) 60°-90° 0.85 LOW (RED) 60°-90° 1 MED-LOW (ORANGE) 60°-90°

FH085D36E

FH085D36E

HIGH VOLTAGE

BROWN

BROWN

HIGH (BLACK)

HIGH (BLACK)

FH110D48E

FH110D48E

FH110D60E

FH110D60E

FIELD WIRING

BLOWER CAPACITOR RATING

BLOWER CAPACITOR RATING

UNIT MOTOR CAPACITOR FH085D36E 1/3 5/370 FH110D48E 1/2 7.5/370 FH110D60E 3/4 15/370

UNIT MOTOR CAPACITOR FH085D36E 1/3 5/370 FH110D48E 1/2 7.5/370 FH110D60E 3/4 15/370

4047-118 B

BLOWER ASSEMBLY

Page 38 of the 321 Studios FH110D60E user manual — HEAT
Page 38 · click to enlarge
Page 38
321 Studios FH110D60E — FIGURE 4 TYPICAL UNIT SETUP diagram (page 38)
Fig. 19

COLING BLWR.

COLING BLWR.

0.55 LOW (RED) 60°-90° HIGH (BLACK) 0.65 LOW (RED) 60°-90° HIGH (BLACK) 0.75 MED (BLUE) 60°-90° HIGH (BLACK) 0.85 MED. HIGH (BLUE)60°-90° HIGH (BLACK)

0.55 LOW (RED) 60°-90° HIGH (BLACK) 0.65 LOW (RED) 60°-90° HIGH (BLACK) 0.75 MED (BLUE) 60°-90° HIGH (BLACK) 0.85 MED. HIGH (BLUE)60°-90° HIGH (BLACK)

1 MED. HIGH (BLUE)60°-90° HIGH (BLACK)

1 MED. HIGH (BLUE)60°-90° HIGH (BLACK)

1.1 MED. HIGH (BLUE)60°-90° HIGH (BLACK)

1.1 MED. HIGH (BLUE)60°-90° HIGH (BLACK)

1.25 MED. HIGH (BLUE)60°-90° HIGH (BLACK) FLR140D60E

1.25 MED. HIGH (BLUE)60°-90° HIGH (BLACK) FLR140D60E

CFM@

.50" WC UNIT NOM. A/C

CFM@

.50" WC UNIT NOM. A/C

4047-119 C

Y C W Rh Y G Rc THERMOSTAT

2 LOW (RED) 775 2.5 MED (BLUE) 1070 3 HIGH (BLACK) 1275 2.5 LOW (RED) 1065 3 MED LOW (ORANGE) 1235 3.5 MED HIGH (BLUE) 1415 4 HIGH (BLACK) 1525 3 LOW (RED) 1190 3.5 MED LOW (ORANGE) 1400 4 MED HIGH (BLUE) 1640 5 HIGH (BLACK) 2250

2 LOW (RED) 775 2.5 MED (BLUE) 1070 3 HIGH (BLACK) 1275 2.5 LOW (RED) 1065 3 MED LOW (ORANGE) 1235 3.5 MED HIGH (BLUE) 1415 4 HIGH (BLACK) 1525 3 LOW (RED) 1190 3.5 MED LOW (ORANGE) 1400 4 MED HIGH (BLUE) 1640 5 HIGH (BLACK) 2250

TEMP. RATING OF 200°C.

REPRESENT FIELD WIRING.

SPEED

SPEED

IF PRIMARY LIMIT WIRES

ARE TO BE REPLACED,

USE WIRE WITH INSUL.

CONNECT TO "SPARE"

T87F/Q539A1220

OR EQUIVELANT

CONNECTION POINT.

CONNECTION POINT.

ONLY ONE HEATING

AND COOLING SPEED

CAN BE CONNECTED.

NOTES

HEATING SPEED

COOLING SPEED

ALL OTHER TAPS

DASHED LINES

(TONS) SPEED (COLOR)

(TONS) SPEED (COLOR)

TERMINALS.

COOLING BLOWER SPEEDS

COOLING BLOWER SPEEDS

TEMP.

TEMP.

RISE

RISE

1 UNIT MOTOR CAPACITOR

UNIT GPH INPUT HTG. BLWR SPD.

UNIT GPH INPUT HTG. BLWR SPD.

FACTORY SETTINGS

FACTORY SETTINGS

*ELECTRICAL SHOCK HAZARD *DISCONNECT POWER BEFORE SERVICING.

(COLOR)

(COLOR)

UNIT MOTOR CAPACITOR

BLOWER CAPACITOR RATING

BLOWER CAPACITOR RATING

FLF/R085D36E 1/3 5/370 FLF/R110D48E 1/2 7.5/370 FLF/R110D60E

FLF/R085D36E 1/3 5/370 FLF/R110D48E 1/2 7.5/370 FLF/R110D60E

FLR140D60E 3/4 15/370

FLR140D60E 3/4 15/370

DANGER !

FLF/R085D36E

FLF/R085D36E

FLF/R110D48E

FLF/R110D48E

FLF/R110D60E

FLF/R110D60E

FLR140D60E

FLR140D60E

FLF/R085D36E

FLF/R085D36E

FLF/R110D48E

FLF/R110D48E

FLF/R110D60E

FLF/R110D60E

COND.

UNIT

24V. CONN.

BLACK GROUND NEUTRAL

HOT

GREEN

BLUE

GREEN WHITE

BLACK

BLACK

WIRING DIAGRAM

HEAT EX. AREA

FLF/R SERIES

SEC1

BLOWER CONTROL T

T

SEC2

TRANSFORMER

COM 120V

BACKUP LIMIT PRIMARY LIMIT

SPR3

SPR1 SPR2

240 210 180 150 R W G Y C

CONTROL PANEL

L2 COM

WHITE WHITE WHITE

PURPLE PURPLE

COOL EAC

BLACK

BLACK BLACK

"HEAT" AND "COOL"

SEE CHART FOR

WIRE COLORS.

HEAT

HUM

T T 1 2

BLOWER CAPACITOR

5 4 3 2 1 BLACK

BLACK

ORANGE

WHITE

BLACK

BLUE

RED

BURNER ASS'Y

OIL VALVE

BURNER

IGNITOR

CAD CELL

BLOWER ASSEMBLY

MOTOR

BROWN

BROWN

BLACK

VALVE

BURNER

IGNITOR

CAD CELL

MOTOR

RETURN AREA

Page 39 of the 321 Studios FH110D60E user manual — T T 1 2
Page 39 · click to enlarge
Page 39
321 Studios FH110D60E — FIGURE 4 TYPICAL UNIT SETUP diagram (page 39)
Fig. 20

2 LOW (RED) 775 2.5 MED (BLUE) 1070 3 HIGH (BLACK) 1230

2 LOW (RED) 775 2.5 MED (BLUE) 1070 3 HIGH (BLACK) 1230

WIRING DIAGRAM

FC SERIES

240 210 180 150 R W G Y C

T T 1 2

BLOWER ASSEMBLY (1/3 HP)

BLOWER CAPACITOR

BURNER ASS'Y

BACKUP LIMIT

OIL VALVE

BURNER

IGNITOR

CAD CELL

MOTOR

BLACK

BROWN

BROWN

VALVE

BURNER

IGNITOR

CAD CELL

MOTOR

SWITCH

DOOR

RETURN AREA

(5/370)

Ask about the 321 Studios FH110D60E

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 321 Studios FH110D60E

Be the first to ask — other owners or our team will answer.

Original document

321 Studios FH110D60E manual PDF

39 pages·901 KB·Coffeemaker·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…