EN
Official user manual

321 Studios W-505

5 pages·105 KB·Gas Grill·PDF·ENDEFRITNLJA
321 Studios W-505
Table of Contents 24 sections W-505 ™ · W-505 · W-505™ INSTALLATION · SCREW 6-32 X 3 / 8 ” (2) · … ShowHide
Page 1 of the 321 Studios W-505 user manual — SCREW 6-32 X 3 / 8 ” (2)
Page 1 · click to enlarge
Page 1
321 Studios W-505 — W-505 ™ diagram (page 1)
Fig. 1
321 Studios W-505 — W-505 ™ diagram (page 1)
Fig. 2

W-505 ™

W-505™ Control includes all of the standard features, in a new design that is compatible with a number of Casablanca fan Models . The W-505™ hand-held remote provides three forward or reverse fan speeds, full spectrum light dimming and has an optional wall bracket. The W-505™ may be used alone to control several fans or with extra controls to operate a single fan from different locations.

W-505

W-505™ INSTALLATION

321 Studios W-505 — W-505 diagram (page 1)
Fig. 3
321 Studios W-505 — W-505 diagram (page 1)
Fig. 4

SCREW 6-32 X 3 / 8 ” (2)

WOOD SCREW

12V BATTERY

W-505 CONTROL (TRANSMITTER)

W-505 CONTROL

DRYWALL

SCREW 6-32 X 1”(2)

ANCHOR

HOLDER

W-505™ CONTROL BRACKET INSTALLATION

321 Studios W-505 — SCREW 6-32 X 3 / 8 ” (2) diagram (page 1)
Fig. 5
321 Studios W-505 — SCREW 6-32 X 3 / 8 ” (2) diagram (page 1)
Fig. 6
321 Studios W-505 — SCREW 6-32 X 3 / 8 ” (2) diagram (page 1)
Fig. 7

Standard Light Switch Step A. Remove the two screws holding the switch cover plate. Do not remove the cover plate. Step B. Orient the control bracket as shown and line up the two inner mounting holes with those on the switch. Step C. Install and tighten screws by hand only.

Wall Controls - CONTINUED

Show 5 more labels / short text on this page
(Transmitter) · 1” (2) · 6-32 (2) · Rocker Switch · Standard Switch
Page 2 of the 321 Studios W-505 user manual — 12V BATTERY
Page 2 · click to enlarge
Page 2

Wall Controls - CONTINUED

W-505 ™

W-505™ CONTROL BRACKET INSTALLATION

Wall Installation Step A. Locate a 2x4 wall stud in a convenient location. Step B. Orient the control bracket as shown over the 2x4 stud. Step C. Use the 1” wood screws in either the inner or outer mounting holes. Install and tighten screws by hand only.

321 Studios W-505 — W-505 ™ diagram (page 2)
Fig. 8

DRYWALL ANCHOR

DECOR OVALHEAD SCREWS

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved in writing by Casablanca Fan Co. may void the user’s authority to operate this equipment.

W-505™ BATTERY INSTALLATION

Wall Controls - CONTINUED

321 Studios W-505 — W-505™ BATTERY INSTALLATION diagram (page 2)
Fig. 9

Remove Battery Door Turn control on its front. Twist a coin or use your finger to unsnap the door A. Lift door away from control B and remove C.

321 Studios W-505 — W-505™ BATTERY INSTALLATION diagram (page 2)
Fig. 10

Install Battery Press battery into control aligned as shown.Observe proper polarity. Replace the battery door.

12V BATTERY

Changes or modifications not expressly approved in writing by Casablanca Fan Co. may void the user’s authority to operate this equipment.

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Wall Controls - CONTINUED

Page 3 of the 321 Studios W-505 user manual — Light Control
Page 3 · click to enlarge
Page 3

Wall Controls - CONTINUED

W-505 ™

W-505™ PLACING CONTROL ON TO THE HOLDER

321 Studios W-505 — W-505 ™ diagram (page 3)
Fig. 11

Control Storage

Angle control in top first until the unit can be gently pushed back and snapped into place.

Removing Control

Gently Pull the lower edge of the control out from the holder.

W-505™ OPERATION

Fan Control

To start the fan. Press the selected speed but-

321 Studios W-505 — Fan Control diagram (page 3)
Fig. 12 · Fan Control
  • ton to run the fan at the desired speed.
  • =Low speed
  • =Medium speed
  • =High speed To turn off the fan. Press the FAN OFF button.

Airflow Direction

To reverse the airflow press the RE- VERSE button. Reverse operates at any speed whether fan is on or off. The fan returns to its set speed after reversing.

Light Control

Turn the light on or off independently from the fan by pressing the LIGHT button. Keep pressing the button in excess of 0.7 sec- onds, it becomes a dimmer. The light varies from ‘bright’ to ‘dim’ over approxi- mately 8 seconds. This sequence will reverse the light when it reaches the brightest or dimmest level if you continue to hold the LIGHT button. Release the but- ton when the desired level is reached.

Page 4 of the 321 Studios W-505 user manual — CHECKING THE SWITCH SETTINGS
Page 4 · click to enlarge
Page 4

CHECKING THE SWITCH SETTINGS

321 Studios W-505 — CHECKING THE SWITCH SETTINGS diagram (page 4)
Fig. 13
321 Studios W-505 — CHECKING THE SWITCH SETTINGS diagram (page 4)
Fig. 14

You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately.

Dip Switch Set to “0101”

Dip Switch Set to “1000”

1. At the circuit breaker or fuse box, turn the power off for the fan you want to change.
321 Studios W-505 — CHECKING THE SWITCH SETTINGS diagram (page 4)
Fig. 15
2. Open the battery door of the Prime•Touch control and remove the batteries.
3. Change the dip switch settings, assuring that they are different from the previously installed Prime•Touch fan.
4. Re-install the batteries and the battery door on the control.
5. At the circuit breaker or fuse box, turn the power back on for the fan whose frequency you are changing.
6. Within 20 seconds of restoring power, push the HIGH, MED, and LOW buttons (in that order).

If the fan is not functioning after installation:

1. Check to make sure that batteries are installed correctly in the control.
321 Studios W-505 — CHECKING THE SWITCH SETTINGS diagram (page 4)
Fig. 16
2. Turn the power off to the fan (from the circuit breaker) for at least 5 seconds.
321 Studios W-505 — CHECKING THE SWITCH SETTINGS diagram (page 4)
Fig. 17
3. Turn the power back on (at the circuit breaker) and push the HIGH, MED, and LOW buttons–in that order–within 20 seconds.
4. The fan should now function properly.

Circuit Breaker · Box

Page 5 of the 321 Studios W-505 user manual — CHECKING THE SWITCH SETTINGS
Page 5 · click to enlarge
Page 5
Page 5 of the 321 Studios W-505 user manual — CHECKING THE SWITCH SETTINGS

Ask about the 321 Studios W-505

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 321 Studios W-505

Be the first to ask — other owners or our team will answer.

Original document

321 Studios W-505 manual PDF

5 pages·105 KB·Gas Grill·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…