EN
Official user manual

321 Studios 7322 230

28 pages·671 KB·Coffeemaker·PDF·ENDEFRITNLJA
321 Studios 7322 230
Table of Contents 37 sections USER'S MANUAL FOR INDUCTION HOBS · cod. 7322 230 · SAFETY · Precautions before using · … ShowHide
Page 1 of the 321 Studios 7322 230 user manual — USER'S MANUAL FOR INDUCTION HOBS
Page 1 · click to enlarge
Page 1
321 Studios 7322 230 — USER'S MANUAL FOR INDUCTION HOBS diagram (page 1)
Fig. 1

USER'S MANUAL FOR INDUCTION HOBS

cod. 7322 230

Page 2 of the 321 Studios 7322 230 user manual — USER'S MANUAL FOR INDUCTION HOBS
Page 2 · click to enlarge
Page 2
Page 2 of the 321 Studios 7322 230 user manual — USER'S MANUAL FOR INDUCTION HOBS
Page 3 of the 321 Studios 7322 230 user manual — Using the appliance
Page 3 · click to enlarge
Page 3

SAFETY

Precautions before using

Unpack all the materials. The installation and connecting of the appliance have to be done by approved

specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors. To be used, the appliance must be well-equipped and installed in a kitchen unit and an

adapted and approved work surface. This domestic appliance is exclusively for the cooking of food, to the exclusion of any

other domestic, commercial or industrial use. Remove all labels and self-adhesives from the ceramic glass. Do not change or alter the appliance. The cooking plate can not be used as freestanding or as working surface. The appliance must be grounded and connected conforming to local standards. Do not use any extension cable to connect it. The appliance can not be used above a dishwasher or a tumble-dryer: steam may

damage the electronic appliances.

Using the appliance

Switch the heating zones off after using. Keep an eye on the cooking using grease or oils: that may quickly ignite. Be careful not to burn yourself while or after using the appliance. Make sure no cable of any fixed or moving appliance contacts with the glass or the hot

saucepan. Magnetically objects (credit cards, floppy disks, calculators) should not be placed near to

the engaged appliance. Do not place any metallic object except heating containers. In case of untimely engaging

or residual heat, this one may heat, melt or even burn. Never cover the appliance with a cloth or a protection sheet. This is supposed to become

very hot and catch fire. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Metallic objects such as knives, forks, spoons and lids should not be placed on the hob

surface since they can get hot.

Page 4 of the 321 Studios 7322 230 user manual — DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT
Page 4 · click to enlarge
Page 4

Precautions not to damage the appliance

Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage

the ceramic glass. Sand or other abrasive materials may damage ceramic glass. Avoid dropping objects, even little ones, on the vitroceramic. Make sure that the ventilation of the appliance works according to the manufacturer’s

instructions. Do not hit the edges of the glass with saucepans. Do not put or leave empty saucepans on the vitroceramic hobs. Sugar, synthetic materials or aluminium sheets must not contact with the heating zones.

These may cause breaks or other alterations of the vitroceramic glass by cooling: switch on the appliance and take them immediately out of the hot heating zone (be careful: do not burn yourself). Never place any hot container over the control panel. If a drawer is situated under the embedded appliance, make sure the space between the

content of the drawer and the inferior part of the appliance is large enough (2cm). This is essential to guaranty a correct ventilation. Never put any inflammable object (ex. sprays) into the drawer situated under the

vitroceramic hob. The eventual cutlery drawers must be resistant to heat.

Precautions in case of appliance failure

If a defect is noticed, switch on the appliance and turn off the electrical supplying. If the ceramic glass is cracked or fissured, you must unplug the appliance and contact

the after sales service. Repairing has to be done by specialists. Do not open the appliance by yourself. WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of

electric shock.

Other protections

the pan must have to cover as much as possible the cooking zone. For the users of pacemaker, the magnetic field could influence its operating. We

recommend getting information to the retailer or of the doctor. Do not to use aluminium or synthetic material containers: they could melt on still hot

cooking zones.

DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT

PANS WHICH ARE NOT ADAPTED TO INDUCTION. RISKS OF BURNS AND DETERIORATION OF THE HOB.

Page 5 of the 321 Studios 7322 230 user manual — Sensitive touches
Page 5 · click to enlarge
Page 5

DESCRIPTION OF THE APPLIANCE

Technical data

TypeTotal PowerPositionNominal Power*Booster Power*Diameter 73212403000WFront2300W3000W250 mm 73222403400WFront left Rear right1200W 2300W1400W 3000W160 mm 200 mm

Control panel

USE

Timer / Power display

321 Studios 7322 230 — Control panel diagram (page 5)
Fig. 2 · Control panel

[ - ] key Timer key

[ + ] / Booster

Sensitive touches

Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger touches the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. Touch only one key on the same time.

Show 6 more labels / short text on this page
Control light timer · Locking key · Locking light · On / Off · key · key
Page 6 of the 321 Studios 7322 230 user manual — Starting-up
Page 6 · click to enlarge
Page 6

Display

0 Zero The heating zone is activated

1…9 Power level Selection of the cooking level

U Pan Detection No pan or inadequate pan

E Error message Electronic failure

H Residual heat The heating zone is hot

P Booster The boosted power is activated

Ventilation

The cooling system is fully automatic. The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level. The ventilation starts his high speed when the hob is intensively used. The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough.

STARTING-UP AND APPLIANCE MANAGEMENT

Before the first use

Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface.

Induction principle

An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone.

Of course the pan has to be adapted:

All ferromagnetic pans are recommended (please verify it thanks a little magnet): cast

iron and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms… Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic,

stoneware… The induction heating zone adapts automatically the size of the pan. With a too small diameter the pan doesn’t work. This diameter is varying in function of the heating zone diameter. If the pan is not adapted to the induction hob the display will show [ U ].

Starting-up

You must first start-up the hob, then the heating zone :

Start-up/ switch off the hob :

Action Control panel Display

To start Press key [ 0/I ] 2 x [ 0 ] To stop Press key [ 0/I ] nothing or [ H ]

Display Designation Function

Page 7 of the 321 Studios 7322 230 user manual — Booster function
Page 7 · click to enlarge
Page 7

Start-up/ switch off the heating zone :

Action Control panel Display

Increase power Press key [ + ] [ 4 ] to [ 9 ] Decrease power Press key [ - ] [ 9 ] to [ 1 ] Stop Press simultaneous[ + ] and [ - ] [ 0 ] or [ H ] or press [ - ] [ 0 ] or [ H ]

If no setting are made in 20 seconds the hob return in waiting position.

Pan detection

The pan detection ensures a perfect safety. The induction doesn’t work:

If there is no pan on the heating zone or if this pan is not adapted to the induction. In this

case it is impossible to increase the power and the display shows [ U ]. This symbol disappears when a pan is put on the heating zone. If the pan is removed from the heating zone the operation is stopped. The display shows

[ U ]. The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level chosen before.

Residual heat indication

After the switch-off of the hob, the heating zone is still hot and indicates [ H ] on the display. The symbol [ H ] disappears when the heating zone may be touched without danger. As far as the residual heat indicator is on light, don’t touch the heating zone and don’t put any heat sensitive object on them. There are risks of burn and fire.

Booster function

The booster function [ P ] grants a boost of power to the selected heating zone. If this function is activated the heating zones works during 10 minutes with an ultra high power. The booster is foreseen for example to heat up rapidely big quantities of water, like nuddles cooking.

Start up / Stop the booster function :

Action Control panel Display

Increase power Press key [ + ] or [ - ] [ 1 ] to [ 9 ] Start up the booster Press key [ + ] [ P ] during 10 min. Stop the booster Press key [ - ] [ 9 ]

Power management :

The whole cooking hob is equipped by a maximum of power. When the booster function isactivated, and not to exceed the maximum power, the electronic system orders to reduce automatically the power level of an other heating zone. The display is blinking on [ 9 ] during a few seconds and then shows the maximum of power allowed ( [ 6 ] or [ 8 ] ). Heating zone selected The other heating zone: (example: power level 9)

[ P ] is displayed [ 9 ] goes to [ 7 ] or [ 8 ] depending the type of zone

Page 8 of the 321 Studios 7322 230 user manual — Control panel locking
Page 8 · click to enlarge
Page 8

Timer

The timer is able to be used simultaneous with all 2 heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone.

Setting and modification of the cooking time

Action Control panel Display To select the heating zone Press key [ + ] or [ - ] [ 4 ] or [ 9 ] To select the power level Press key [ + ] or [ - ] [ 1 ] … [ 9 ] To select « Timer » Press key [ ] [ 00 ] minutes Decrease the time Press key [ - ] [ 30 ] to 29,28,27,... Increase the time Press key [ + ] The time increases… After a few seconds the control light stops with blinking. The time is confirmed and the cooking starts.

To stop the cooking time

Action Control panel Display To select « Timer » Press key [ ] The remaining time To stop the « Timer » Press key [ - ] then [ ] Displays [ 00 ] then stops If they are several timer activated you must repeat this operation.

Automatic stop at the end of the cooking time

As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings and the heating zone stops. To stop the sound and the blinking it is enough to press key [ ].

Action Control panel Display Activate the hob Press key [ 0/I ] The zone control lights are on To select « Timer » Press key [ ] [ 00 ] minutes Decrease the time Press key [ - ] [ 30 ] to 29,28,27,… Increase the time Press key [ + ] The time increases… After a few seconds the control light stops with blinking and the timer starts.

To stop the egg timer function

Action Control panel Display Activate the hob Press key [ 0/I ] Timer light blinking To stop the « Timer » Press key [ - ] then [ ] Displays [ 00 ] then stops

Control panel locking

To avoid modifying a setting of cooking zones , in particular with within the framework of cleaning the control panel can be locked (with exception to the On/Off key [ 0/I ]).

Action Control panel Display Start Press key [ 0/I ] [ 0 ] or [ H ] on displays Hob locking Press key [ ] [ 0 ] or [ H ] on displays Locking light is on

Action Control panel Display Start Press key [ 0/I ] [ 0 ] on displays Unlocking the hob Press key [ ] [ 0 ] on displays Locking light is off

Egg timer function · Locking · Unlocking

Page 9 of the 321 Studios 7322 230 user manual — Examples of power setting
Page 9 · click to enlarge
Page 9

COOKING ADVICES

Pan quality

Adapted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom. Not adapted materials : aluminium and stainless-steel without ferromagnetic bottom, cupper, brass, glass, ceramic, porcelain. The manufacturers specify if their products are compatible induction. To check if pans are compatibles:

Put a littler water in a pan placed on an induction heating zone set at level [ 9 ].This water

must heat in a few seconds. A magnet stuck on the bottom of the pan. Some pans can make noise when they are placed on an induction cooking zone. This noise doesn’t mean any failure on the appliance and doesn’t influence the cooking operating.

Pan dimension

The cooking zones are, until a certain limit, automatically adapted to the diameter of the pan. However the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone. To obtain the best efficiency of your hob, please place the pan well in the center of the cooking zone.

Examples of power setting

1 to 2Melting ReheatingSauces, butter, chocolate, gelatine Dishes prepared beforehand 2 to 3Simmering DefrostingRice, pudding, sugar syrop Dried vegetables, fish, frozen products 3 to 4SteamVegetables, fish, meat 4 to 5WaterSteamed potatoes, soups, pasta, fresh vegetables 6 to 7Medium cooking SimmeringMeat, lever, eggs, sausages Goulash, roulade, tripe 7 to 8CookingPotatoes, fritters, wafers 9Frying, rosting Boiling waterSteaks, omelettes, fried dishes Water PBoiling waterBoiling significant quantities of water
Page 10 of the 321 Studios 7322 230 user manual — a b c d e f
Page 10 · click to enlarge
Page 10

WHAT TO DO IN CASE OF A PROBLEM

The symbol [ E 4 ] displays :

The hob must be configured according to the following procedure.

I) Warning : before starting all pots must be removed from the cooktop. II) Disconnect the cooktop from the main supply : remove fuse or disconnect circuit breaker. III) Connect the cooktop to the main supply : replace the fuse or connect the circuit breaker. IV) Procedure : You must provide yourself with a ferromagnetic bottom container 16 cm minimum diametre.

* start within 2 minutes after the connection to the main supply * do not use the [ O/I ] key. V) How to cancel the existing configuration :

1. Push on the locking key and keep your finger on the key
321 Studios 7322 230 — WHAT TO DO IN CASE OF A PROBLEM diagram (page 10)
Fig. 3
2. With a finger from the other hand activate successively and quickly a - b - c (7322240) or d - e - f (7321240) keys. Start from left to right. A double "beep" sound will inform you of a bad manipulation and you will have to restart from point 1.

a b c d e f

3. The left display shows alternatively a [ C ] and a [ 0 ]

4) Press the key lock until both displays indicate either [ C ] or [ - ]. 5) Take your fingers away from the keys and press again the [ - ] key during a few seconds until some [ E ] appear. 6) You will hear a "beep" sound and the [ E ] will blink. 7) The [ E ] are automatically transformed into [ C ] → The configuration has been canceled. VI) How to configure the hob ?

1) Use a suitable induction pot with a minimum diametre size of 16cm. 2) Select the heating zone by pushing the corresponding [ + ] key. 3) Put the pot on the corresponding heating zone. 4) Wait until [ C ] converts to [ - ]. The zone is configured 5) Use the same procedure for each other heating zone which displays [ C ] 6) The configuration is made if all zones are detected and if nothing is displayed Use only 1 pot to configure the hob. Never put two or more pots on the heating zones during the configuration. If [ E 4 ] display persists call the After-sales Service

The hob or the cooking zone doesn’t start-up

The hob is badly connected on the electrical network. The protection fuse cut-off The locking function is activated The sensitive keys are covered of grease or water. An object is put on a key.

Page 11 of the 321 Studios 7322 230 user manual — the surface being damaged. ENVIRONMENT PROTECTION
Page 11 · click to enlarge
Page 11

The symbol [ U ] displays

There is no pan on the cooking zone. The pan is not compatible with induction. The bottom diameter of the pan is too small.

The symbol [ C ] or [ E ] displays

Call the After-sales Service.

One or all cooking zones cut-off

The safety system functioned You forgot to cut-off the cooking zone for a long time. One or more sensitive keys are covered. The pan is empty and its bottom overheated. The hob also has an automatic reduction of power level and breaking Automatic

Continuous ventilation after cutting-off the hob

This is not a failure, the fan continuous to protect the electronic device. The fan cooling stops automatically.

MAINTENANCE AND CLEANING

Switch-off the appliance before cleaning. Do not clean the hob if the glass is too hot: risk of burn.

Remove light marks with a damp cloth with washing up liquid diluted in a little water.

Then rinse with cold water and dry the surface thoroughly. Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches

must be absolutely avoided. Do not ever use any steam-driven or pressure appliance. Do not use any object that may scratch the ceramic glass. Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your

ceramic hob or on the pan. Sliding rough saucepans will scratch the surface. Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent

the surface being damaged. ENVIRONMENT PROTECTION

The packaging material is ecological and can be recycled. The worn appliances contain certain noble metals. Apply to the local government about

the possibilities of recycling.

321 Studios 7322 230 — the surface being damaged. ENVIRONMENT PROTECTION diagram (page 11)
Fig. 4 · the surface being damaged. ENVIRONMENT PROTECTION

Don't throw your appliance with the household

refuses Get in touch with the waste collection center of

your commune that is adapted to the recycling of the household appliances.

overheating

Page 12 of the 321 Studios 7322 230 user manual — INSTALLATION INSTRUCTIONS
Page 12 · click to enlarge
Page 12

INSTALLATION INSTRUCTIONS

The installation comes under the exclusive responsibility of specialists. The installer is held to respect the legislation and the standards enforce in his home country.

How to stick the gasket

The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. His installation has to be done carefully, in conformity of the following drawing.

321 Studios 7322 230 — INSTALLATION INSTRUCTIONS diagram (page 12)
Fig. 5

Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection sheet (3).

ApplianceCut out 7321240360 x 490 mm 7322240360 x 490 mm

Ensure that there is a distance of 50 mm between the hob and the wall or sides. The hobs are classified as “Y” class for heat protection. Ideally the hob should be

installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob. The piece of furniture or the support in which the hob is to be fitted, as well as the edges

of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C. The mural rods of edge must be heat-resisting. Materials which are often used to make worktops expand on contact with water. To

protect the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces. Not to install the hob to the top of a not ventilated oven or a dishwasher. To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air

circulation of the electronic device. If a drawer is placed under the work, avoid to put into this drawer flammable objects (for

example: sprays) or not heat-resistant objects. The safety gap between the hob and the cooker hood placed above must respect the

indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 760 mm. The connection cord should be subjected, after building, with no mechanical constraint,

such for example of the fact of the drawer.

Fitting – installing

Page 13 of the 321 Studios 7322 230 user manual — ELECTRICAL CONNECTION
Page 13 · click to enlarge
Page 13

ELECTRICAL CONNECTION

The installation of this appliance and the connection to the electrical network should be

entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously. Protection against the parts under tension must be ensured after the building-in. The data of connection necessary are on the stickers place on the hob casing near the

connection box. The connection to the main must be made using an earthed plug or via an omnipolar

circuit breaking device with a contact opening of at least 3 mm. The electrical circuit must be separated from the network by adapted devices, for

example: circuit breakers, fuses or contactors.

This appliance has only to be connected to a network 230 V~ 50/60 Hz Connect always the earth wire. Respect the connection diagram. Use the connecting cable that is attached to the device. The green / yellow wire correspond to the earth wire, the blue wire correspond neutral wire and the brown wire correspond to the phase.

Mains Connection Cable diameter Cable Protection calibre

230V~ 50/60Hz 1 Phase + N 3 x 1,5 mm2 H 05 VV - F H 05 RR - F 16 A *

* calculated with the simultaneous factor following standard EN 60 335-2-6/1990 Caution! Ensure that you correctly attach the wires and the bridges and tighten the screws properly.

We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been

equipped with a faulty earth connection.

Page 14 of the 321 Studios 7322 230 user manual — ELECTRICAL CONNECTION
Page 14 · click to enlarge
Page 14

cod. 9606885

Foster spa 42041 Brescello (RE) - Italy tel. +39.0522.687425 - tel. Servizio Assistenza +39.0522.684450 fax +39.0522.686019 - fax Servizio Ricambi +39.0522.962166 e-mail: service@fosterspa.com www.fosterspa.com

13848/3

Page 15 of the 321 Studios 7322 230 user manual — ELECTRICAL CONNECTION
Page 15 · click to enlarge
Page 15
Page 15 of the 321 Studios 7322 230 user manual — ELECTRICAL CONNECTION
Page 16 of the 321 Studios 7322 230 user manual — Using the appliance
Page 16 · click to enlarge
Page 16

SAFETY

Precautions before using

Unpack all the materials. The installation and connecting of the appliance have to be done by approved

specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors. To be used, the appliance must be well-equipped and installed in a kitchen unit and an

adapted and approved work surface. This domestic appliance is exclusively for the cooking of food, to the exclusion of any

other domestic, commercial or industrial use. Remove all labels and self-adhesives from the ceramic glass. Do not change or alter the appliance. The cooking plate can not be used as freestanding or as working surface. The appliance must be grounded and connected conforming to local standards. Do not use any extension cable to connect it. The appliance can not be used above a dishwasher or a tumble-dryer: steam may

damage the electronic appliances.

Using the appliance

Switch the heating zones off after using. Keep an eye on the cooking using grease or oils: that may quickly ignite. Be careful not to burn yourself while or after using the appliance. Make sure no cable of any fixed or moving appliance contacts with the glass or the hot

saucepan. Magnetically objects (credit cards, floppy disks, calculators) should not be placed near to

the engaged appliance. Do not place any metallic object except heating containers. In case of untimely engaging

or residual heat, this one may heat, melt or even burn. Never cover the appliance with a cloth or a protection sheet. This is supposed to become

very hot and catch fire. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Metallic objects such as knives, forks, spoons and lids should not be placed on the hob

surface since they can get hot.

Page 17 of the 321 Studios 7322 230 user manual — DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT
Page 17 · click to enlarge
Page 17

Precautions not to damage the appliance

Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage

the ceramic glass. Sand or other abrasive materials may damage ceramic glass. Avoid dropping objects, even little ones, on the vitroceramic. Make sure that the ventilation of the appliance works according to the manufacturer’s

instructions. Do not hit the edges of the glass with saucepans. Do not put or leave empty saucepans on the vitroceramic hobs. Sugar, synthetic materials or aluminium sheets must not contact with the heating zones.

These may cause breaks or other alterations of the vitroceramic glass by cooling: switch on the appliance and take them immediately out of the hot heating zone (be careful: do not burn yourself). Never place any hot container over the control panel. If a drawer is situated under the embedded appliance, make sure the space between the

content of the drawer and the inferior part of the appliance is large enough (2cm). This is essential to guaranty a correct ventilation. Never put any inflammable object (ex. sprays) into the drawer situated under the

vitroceramic hob. The eventual cutlery drawers must be resistant to heat.

Precautions in case of appliance failure

If a defect is noticed, switch off the appliance and turn off the electrical supplying. If the ceramic glass is cracked or fissured, you must unplug the appliance and contact

the after sales service. Repairing has to be done by specialists. Do not open the appliance by yourself. WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of

electric shock.

Other protections

Make sure that the container pan is always centred on the cooking zone. The bottom of

the pan must have to cover as much as possible the cooking zone. For the users of pacemaker, the magnetic field could influence its operating. We

recommend to request necessary information before using the appliance, both tot he vendor and one’s Doctor. Do not to use aluminium or synthetic material containers: they could melt on still hot

cooking zones.

DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT

PANS WHICH ARE NOT ADAPTED TO INDUCTION. RISKS OF BURNS AND DETERIORATION OF THE HOB.

Page 18 of the 321 Studios 7322 230 user manual — Sensitive touches
Page 18 · click to enlarge
Page 18

DESCRIPTION OF THE APPLIANCE

Technical data

Type Total Power Position Nominal Power* Booster Power* Diameter

1200W 2000W 1400W 2300W 150 mm 220 mm * The given power may change according to the dimensions and material of the pan.

Control panel

Timer / Power display

321 Studios 7322 230 — Control panel diagram (page 18)
Fig. 6 · Control panel

[ - ] key Timer key

[ + ] / Booster

USE

Sensitive touches

Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger touches the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. Touch only one key on the same time.

Show 8 more labels / short text on this page
7322230 3700W Front · Rear · Control light timer · Locking key · Locking light · On / Off · key · key
Page 19 of the 321 Studios 7322 230 user manual — Induction principle
Page 19 · click to enlarge
Page 19

Display

0 Zero The heating zone is activated

1…9 Power level Selection of the cooking level

U Pan Detection No pan or inadequate pan

E Error message Electronic failure

H Residual heat The heating zone is hot

P Booster The boosted power is activated

Ventilation

The cooling system is fully automatic. The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level. The ventilation starts his high speed when the hob is intensively used. The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough.

STARTING-UP AND APPLIANCE MANAGEMENT

Before the first use

Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface.

Induction principle

An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone.

Of course the pan has to be adapted:

All ferromagnetic pans are recommended (please verify it thanks a little magnet): cast

iron and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms… Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic,

stoneware… The induction heating zone adapts automatically the size of the pan. With a too small diameter the pan doesn’t work. This diameter is varying in function of the heating zone diameter. If the pan is not adapted to the induction hob the display will show [ U ].

Display Designation Function

Page 20 of the 321 Studios 7322 230 user manual — Booster function
Page 20 · click to enlarge
Page 20

Starting-up

You must first start-up the hob, then the heating zone :

Start-up/ switch off the hob :

Action Control panel Display

To start Press key [ 0/I ] 2 x [ 0 ] To stop Press key [ 0/I ] nothing or [ H ]

Start-up/ switch off the heating zone :

Action Control panel Display

Increase power Press key [ + ] [ 4 ] to [ 9 ] Decrease power Press key [ - ] [ 9 ] to [ 1 ] Stop Press simultaneous[ + ] and [ - ] [ 0 ] or [ H ] or press [ - ] [ 0 ] or [ H ]

If no setting are made in 20 seconds the hob return in waiting position.

Pan detection

The pan detection ensures a perfect safety. The induction doesn’t work:

If there is no pan on the heating zone or if this pan is not adapted to the induction. In this

case it is impossible to increase the power and the display shows [ U ]. This symbol disappears when a pan is put on the heating zone. If the pan is removed from the heating zone the operation is stopped. The display shows

[ U ]. The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level chosen before.

Residual heat indication

After the switch-off of the hob, the heating zone is still hot and indicates [ H ] on the display. The symbol [ H ] disappears when the heating zone may be touched without danger. As far as the residual heat indicator is on light, don’t touch the heating zone and don’t put any heat sensitive object on them. There are risks of burn and fire.

Booster function

The booster function [ P ] grants a boost of power to the selected heating zone. If this function is activated the heating zones works during 10 minutes with an ultra high power. The booster is foreseen for example to heat up rapidly big quantities of water. Start up / Stop the booster function :

Action Control panel Display

Increase power Press key [ + ] or [ - ] [ 1 ] to [ 9 ] Start up the booster Press key [ + ] [ P ] for 10 min Stop the booster Press key [ - ] [ 9 ]

Page 21 of the 321 Studios 7322 230 user manual — Timer
Page 21 · click to enlarge
Page 21

Power management :

The cooking hob is equipped with a power limiting system. When the booster function is activated, and not to exceed the maximum power, the electronic system orders to reduce automatically the power level of an other heating zone. The display is blinking on [ 9 ] during a few seconds and then shows the maximum of power allowed. Heating zone selected The other heating zone: (example: power level 9)

[ P ] is displayed [ 9 ] goes to [ 7 ] or [ 8 ] depending the type of zone

Timer

The timer is able to be used simultaneous with all 2 heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone.

Setting and modification of the cooking time

Action Control panel Display To select the heating zone Press key [ + ] or [ - ] [ 4 ] or [ 9 ] To select the power level Press key [ + ] or [ - ] [ 1 ] … [ 9 ] To select « Timer » Press key [ ] [ 00 ] minutes Decrease the time Press key [ - ] [ 30 ] to 29,28,27,... Increase the time Press key [ + ] The time increases…

After a few seconds the control light stops with blinking.

The time is confirmed and the cooking starts.

To stop the cooking time Action Control panel Display To select « Timer » Press key [ ] The remaining time To stop the « Timer » Press key [ - ] then [ ] Displays [ 00 ] then stops

If there are several timers activated you must repeat this operation.

Automatic stop at the end of the cooking time

As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings and the heating zone stops. To stop the sound and the blinking it is enough to press key [ ].

Action Control panel Display Activate the hob Press key [ 0/I ] zone control lights are on To select « Timer » Press key [ ] [ 00 ] minutes Decrease the time Press key [ - ] [ 30 ] to 29,28,27,… Increase the time Press key [ + ] The time increases…

After a few seconds the control light stops with blinking and the timer starts.

To stop the egg timer function

Action Control panel Display Activate the hob Press key [ 0/I ] Timer light blinking To stop the « Timer » Press key [ - ] then [ ] Displays [ 00 ] then stops

Egg timer function

Page 22 of the 321 Studios 7322 230 user manual — Pan dimension
Page 22 · click to enlarge
Page 22

Control panel locking

To avoid modifying a setting of cooking zones , in particular with within the framework of cleaning the control panel can be locked (with exception to the On/Off key [ 0/I ]).

Action Control panel Display Start Press key [ 0/I ] [ 0 ] or [ H ] on displays Hob locking Press key [ ] [ 0 ] or [ H ] on displays Locking light is on

Action Control panel Display Start Press key [ 0/I ] [ 0 ] on displays Unlocking the hob Press key [ ] [ 0 ] on displays Locking light is off

COOKING ADVICES

Pan quality

Adapted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom. Not adapted materials : aluminium and stainless-steel without ferromagnetic bottom, cupper, brass, glass, ceramic, porcelain. The manufacturers specify if their products are compatible induction. To check if pans are compatibles:

Put a littler water in a pan placed on an induction heating zone set at level [ 9 ].This water

must heat in a few seconds. A magnet stuck on the bottom of the pan. Some pans can make noise when they are placed on an induction cooking zone. This noise doesn’t mean any failure on the appliance and doesn’t influence the cooking operating.

Pan dimension

The cooking zones are, until a certain limit, automatically adapted to the diameter of the pan. However the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone. To obtain the best efficiency of your hob, please place the pan well in the center of the cooking zone.

Locking · Unlocking

Page 23 of the 321 Studios 7322 230 user manual — a b c
Page 23 · click to enlarge
Page 23

Examples of power setting

(The values below are indicative)

1 to 2 Melting Reheating

Sauces, butter, chocolate, gelatine Dishes prepared beforehand 2 to 3 Simmering Defrosting

Rice, pudding, sugar syrop Dried vegetables, fish, frozen products 3 to 4 Steam Vegetables, fish, meat 4 to 5 Water Steamed potatoes, soups, pasta, fresh vegetables 6 to 7 Medium cooking Simmering

Meat, liver, eggs, sausages Goulash, roulade, tripe 7 to 8 Cooking Potatoes, fritters, wafers 9 Frying, rosting Boiling water

Steaks, omelettes, fried dishes Water P Boiling water Boiling significant quantities of water WHAT TO DO IN CASE OF A PROBLEM

The symbol [ E 4 ] displays :

The hob must be configured according to the following procedure.

I) Warning : before starting all pots must be removed from the cooktop. II) Disconnect the cooktop from the main supply : remove fuse or disconnect circuit breaker. III) Connect the cooktop to the main supply : replace the fuse or connect the circuit breaker. IV) Procedure : You must provide yourself with a ferromagnetic bottom container 16 cm minimum diametre.

* start within 2 minutes after the connection to the main supply * do not use the [ O/I ] key. V) How to cancel the existing configuration :

1. Push on the locking key and keep your finger on the key
2. With a finger from the other hand activate successively and quickly a - b - c keys. Start from left to right. A double "beep" sound will inform you of a bad manipulation and you will have to restart from point 1.

a b c

Page 24 of the 321 Studios 7322 230 user manual — a b c
Page 24 · click to enlarge
Page 24
3. The left display shows alternatively a [ C ] and a [ 0 ]

4) Press the key lock until both displays indicate either [ C ] or [ - ]. 5) Take your fingers away from the keys and press again the [ - ] key during a few seconds until some [ E ] appear. 6) You will hear a "beep" sound and the [ E ] will blink. 7) The [ E ] are automatically transformed into [ C ] → The configuration has been canceled. VI) How to configure the hob ?

1) Use a suitable induction pot with a minimum diametre size of 16cm. 2) Select the heating zone by pushing the corresponding [ + ] key. 3) Put the pot on the corresponding heating zone. 4) Wait until [ C ] converts to [ - ]. The zone is configured 5) Use the same procedure for each other heating zone which displays [ C ] 6) The configuration is made if all zones are detected and if nothing is displayed Use only 1 pot to configure the hob. Never put two or more pots on the heating zones during the configuration. If [ E 4 ] display persists call the After-sales Service

The hob or the cooking zone doesn’t start-up

The hob is badly connected on the electrical network. The protection fuse cut-off The locking function is activated The sensitive keys are covered of grease or water. An object is put on a key.

The symbol [ U ] displays

There is no pan on the cooking zone. The pan is not compatible with induction. The bottom diameter of the pan is too small.

The symbol [ C ] or [ E ] displays

Call the After-sales Service.

One or all cooking zones cut-off

The safety system functioned You forgot to cut-off the cooking zone for a long time. One or more sensitive keys are covered. The pan is empty and its bottom overheated. The hob also has an automatic reduction of power level and breaking Automatic

Continuous ventilation after cutting-off the hob

This is not a failure, the fan continuous to protect the electronic device. The fan cooling stops automatically.

overheating

Page 25 of the 321 Studios 7322 230 user manual — ENVIRONMENT PROTECTION
Page 25 · click to enlarge
Page 25

MAINTENANCE AND CLEANING

Switch-off the appliance before cleaning. Do not clean the hob if the glass is too hot: risk of burn.

Remove light marks with a damp cloth with cleaning liquid diluted in a little water. Then

rinse with cold water and dry the surface thoroughly. Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches

must be absolutely avoided. Do not ever use any steam-driven or pressure appliance. Do not use any object that may scratch the ceramic glass. Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your

ceramic hob or on the pan. Sliding rough saucepans will scratch the surface. Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent

the surface being damaged.

ENVIRONMENT PROTECTION

The packaging material is ecological and can be recycled. The worn appliances contain certain noble metals. Apply to the local government about

the possibilities of recycling.

Don't throw your appliance with the household

refuses Get in touch with the waste collection center of

your commune that is adapted to the recycling of the household appliances.

Page 26 of the 321 Studios 7322 230 user manual — INSTALLATION INSTRUCTIONS
Page 26 · click to enlarge
Page 26

INSTALLATION INSTRUCTIONS

The installation comes under the exclusive responsibility of specialists. The installer is held to respect the legislation and the standards enforce in his home country.

How to stick the gasket

The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. His installation has to be done carefully, in conformity of the following drawing.

Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection sheet (3).

The cut out sizes are :

7322230 270 x 500 mm

Ensure that there is a distance of 50 mm between the hob and the wall or sides. The hobs are classified as “Y” class for heat protection. Ideally the hob should be

installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob. The piece of furniture or the support in which the hob is to be fitted, as well as the edges

of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C. The mural rods of edge must be heat-resisting. Materials which are often used in the manufacturing of worktops tend to expand on

contact with water. To protect the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces. Do not install the hob to the top of a not ventilated oven or a dishwasher. Please make sure that a space of of 20 mm is left under the appliance in order to ensure

a good air circulation of air for the electronic device. If a drawer is placed under the work, avoid to put into this drawer flammable objects (for

example: sprays) or not heat-resistant objects. The safety gap between the hob and the cooker hood placed above must respect the

indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 760 mm. The connection cord should be subjected, after building, with no mechanical constraint,

such for example of the fact of the drawer.

Fitting – installing · Appliance Cut out

Page 27 of the 321 Studios 7322 230 user manual — ELECTRICAL CONNECTION
Page 27 · click to enlarge
Page 27

ELECTRICAL CONNECTION

The installation of this appliance and the connection to the electrical network should be

entrusted only to a professionally trained and authorized eletrician, and performed in full respect of all enforced regulations. Protection against the parts under tension must be ensured after the building-in. The data of connection necessary are on the stickers place on the hob casing near the

connection box. The connection to the main must be made using an earthed plug or via an omnipolar

circuit breaking device with a contact opening of at least 3 mm. The electrical circuit must be separated from the network by adapted devices, for

example: circuit breakers, fuses or contactors.

This appliance has only to be connected to a network 230 V~ 50/60 Hz Connect always the earth wire. Respect the connection diagram. Use the connecting cable that is attached to the device. The green / yellow wire correspond to the earth wire, the blue wire correspond neutral wire and the brown wire correspond to the phase.

Mains Connection Cable diameter Cable Protection calibre

230V~ 50/60Hz 1 Phase + N 3 x 1,5 mm2 H 05 VV - F H 05 RR - F 16 A *

* calculated with the simultaneous factor following standard EN 60 335-2-6/1990 Caution! Ensure that you correctly attach the wires and the bridges and tighten the screws properly.

We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection.

Page 28 of the 321 Studios 7322 230 user manual — ENVIRONMENT PROTECTION
Page 28 · click to enlarge
Page 28

cod. 9606886

Foster spa 42041 Brescello (RE) - Italy tel. +39.0522.687425 - tel. Servizio Assistenza +39.0522.684450 fax +39.0522.686019 - fax Servizio Ricambi +39.0522.962166 e-mail: service@fosterspa.com www.fosterspa.com

13846/3

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the 321 Studios 7322 230

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 321 Studios 7322 230

Be the first to ask — other owners or our team will answer.

Original document

321 Studios 7322 230 manual PDF

28 pages·671 KB·Coffeemaker·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…