Instruction/ maintenance manual of the product Network Device Axxius 800 Carrier Access
Go to page of 568
Ax x ius 800 U SER M ANUA L Part Number : 770-01 04 AG Produc t Rele ase: 2. 2 May 200 4.
Copyri ght 200 4 Carrier A ccess Co rporation. All right s reserved . The information presented in th is manual is subject to change without notice and does n ot represent a commitment on the part of Carrier Access Corporation. T he hardware and sof tware described herein are fur nish ed unde r a li cens e o r no n- disc los ur e ag ree men t.
P RE FACE Pref ace Compliance Safety The Axxi us 800 is certified by Underwrite rs Laboratori e s and is in compli ance with UL 6095 0, 3r d Editio n; Safety of I nforma tion T echnolo gy Eq uipme nt and CSA/C2 2.
iv Axxius 800 - Release 2 .2 Preface Complia nce The Fac ility Inte rface Code (FIC) associated with each p rivate line appli cation repres ents the typ e of service that will be prov ided by the telep hone comp any. The fol lowing are curren tly registere d: An FCC-co mpliant tele phone an d modu lar plug is p r ovid ed with this equipm ent.
Axxiu s 800 - R elease 2.2 v Preface Comp lia nce In dust ry C ana da CS -0 3 Registr atio n Number: IC: 2638 A-80 0 ’ ’ NOTICE: This eq uipment me ets the ap plicable Industry Canada T erminal Eq uipment Techni cal Specificati ons. Thi s is confirmed by the registrat ion number.
vi Axxius 800 - Rel ease 2 .2 Preface Safety Information Safety Information CAUTION! A LWAYS USE CAUTION WHEN INSTALL ING TELEPHONE LI NES . R EAD THE CAUTIONS BELOW FOR DETAILS ON SAFETY GU IDEL INES TO P REVENT INJURY .
Axxiu s 800 - R elease 2.2 vii Preface Notices Notices This man ua l con tai ns im por ta nt inf or mati on a nd w arn ing s th at mu st b e fo llow ed to ensure s afe opera tion o f the equi pment. DANGER! A D ANGER NOTICE INDICATES THE PRESEN CE OF A HAZARD THAT CAN OR WI LL CAUSE DE ATH OR SEVERE PERSONA L INJU RY IF THE HAZARD IS NOT AVOIDED .
viii Axxius 800 - Release 2 .2 Preface Electrostatic Discharge (ES D) Precautions Electrostatic Discharge (ESD) Precautions ESD can d amage proces sors, cir cuit car ds, and other el ectronic component s. Always obser ve the fo llowin g preca utions bef ore i nstalli ng a sys tem component .
Axxiu s 800 - R elease 2.2 ix Preface Warran ty Warra nty Carrier Access Corpo ration condition ally warrants to BUYER that PRODUCTS are free from substantial defect in mater ial and workm anshi p und.
x Axxius 80 0 - Rel ease 2.2 Preface Warran ty Warranty Product Returns Before returning any equipment to Carrier Access Corporation, first contact the distribu tor or dealer from which you purc hase d the pr oduct . A Return Material Aut horization (RMA) number is required for all equipment returned to Carrier Access Corpo ratio n.
T ABLE OF C ONTENTS Prefac e Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii FCC Requiremen ts, Part 15 .
xii Axxius 80 0 - Rel ease 2.2 Table of Contents Low Speed Protec tion card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 6 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xiii Table of Contents 2 Physical Instal lation Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Installation Enviro nment . . . . . . . . . . . . . . . . . . . . . . . .
xiv Axxius 80 0 - Rel ease 2.2 Table of Contents Quick Configu ration Reload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Setup of DS0 Management Ch annel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Equipment Req uired.
Axxiu s 800 - R elease 2.2 xv Table of Contents clear key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37 clear log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xvi Axxius 80 0 - Rel ease 2.2 Table of Contents log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62 ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Re lease 2.2 xvii Table of Contents set ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-90 set key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xviii Axxius 80 0 - Rel ease 2.2 Table of Contents set (router) rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 1 set (router) snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xi x Table of Contents set (v35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-170 set (v54) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xx Axxius 80 0 - Rele ase 2.2 Table of Contents show (rou ter) lmi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-197 show (rou ter) login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xxi Table of Contents status (adp cm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-225 status (adp cm) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-226 status (adp cm) performance history .
xxii Axxius 800 - Release 2 .2 Table of Contents telnet (router ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26 0 trace rou te . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xxiii Table of Contents Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xxiv Axxius 800 - Release 2 .2 Table of Contents 9 ISDN BRI Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 ISDN BRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xxv Table of Contents Power Con sumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 Physical .
xxvi Axxius 800 - Rel ease 2 .2 Table of Contents 12 Power Suppl y Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xxvii Table of Contents Card Con figuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6 CLI Comman ds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xxvii i Axxius 800 - Release 2 .2 Table of Contents 15 Termin al Server Router Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2 Quad TSR with TBOS . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xxix Table of Contents 16 V.35/. 54 Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xxx Axxius 800 - Release 2 .2 Table of Contents Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 xxxi Table of Contents C Loopback Tests Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 Test Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xxxii Axxius 80 0 - Rel ease 2. 2 Table of Contents.
C HAPTER Base Platform In this Chapter n Overview n F eatures n Technic al Sp eci ficat io ns n Chassi s n Bu ilt-In Ca rd Handles n Management Ports n Local an d Remo te Mana gement n Control Panel I.
1-2 Axxius 800 - Release 2 .2 Bas e P lat f orm Overview Ove rvi ew The Axxi us 800 Acces s Inte gration Platform s olves t oday’s pr oblems o f multipl e boxes , scala bility, space, power , and env ironmental const raints a ssociat ed with deli vering voi ce and data s ervic es.
Axxiu s 800 - R elease 2.2 1-3 Base Platform Feat ur es The Contr ol Panel Inter face ca rd provid es front acce ss to all the physical interfac es of the DS1 or DS3 Contro ller cards. It provides fou r RJ-48C DS1 conne ctions when usi ng the DS1 Controll er and two s ets of DS3 SMB interf aces whe n using the DS3 Controll er.
1-4 Axxius 800 - Release 2 .2 Bas e P lat f orm Contr olle rs Controllers The Axxi us 800 has t wo cont rollers availabl e, one cont rolle r can supp ort the s ystem, however with two c ontrol ler (sa me type) the syst em is re dundant.
Axxiu s 800 - R elease 2.2 1-5 Base Platform Servi ce Card s OCU-DP Service car d The OCU-DP s ervice ca rd is ava ilable i n a Sing le or Quad p ort opt ion. The OCU-DP int erface se rvice allo ws Digit al Data Ser vice ( DDS) circui t te rminat ions on the Adit 600 pl atform.
1-6 Axxius 800 - Release 2 .2 Bas e P lat f orm Power Su pplies Low Speed Protection ca rd Low spee d protect ion pr ovides bac kup cir cuitry f or any T1 se rvice port o n any Quad T1 ser vice car d in the Axxi us cha ssis.
Axxiu s 800 - R elease 2.2 1-7 Base Platform Technical Specificatio ns Capacities l 2 x Power Supply car ds l 2 x DS3 or DS1 Control ler card s l 1 x Cont rol Panel Inter face car d l 8 x uni versal s.
1-8 Axxius 800 - Release 2 .2 Bas e P lat f orm Technical Specifica tions Alarm Connector s The al arm cont act outp uts ar e per Te lcordia defini tions fo r visi ble and a udible . They oper ate per the sp ec with t he exceptio n that th e audible out puts ca n be disabled with the ACO button.
Axxiu s 800 - R elease 2.2 1-9 Base Platform Chassi s Chassis Controller Relay Card Cards (A1 & A2) Service Ca rd Slots 1-8 Power Supplies (P1 & P2) Future Development Ground Terminals Audible.
1-10 Axxius 80 0 - Rele ase 2.2 Bas e P lat f orm Built-In Card Handles Built-In Card Handle s Sever al of the cards for the Axx ius 800 are desi gned wit h a handle b uilt into the fac epla te t o ass ist in the remo val o f t he c ard from the c has si s.
Axxiu s 800 - R elease 2.2 1-11 Base Platform Control Panel I nterfaces Control Pane l Inte rfaces SMB connector (fema le) The r ecommended mate for the SMB connect or is a n SMB ri ght an gle cri mp connec tor.
1-12 Axxius 80 0 - Rele ase 2. 2 Bas e P lat f orm Control Panel I nterfaces RS-232 Craft Port (Femal e DB-9) The RS-2 32 craft port conne cts vi a a female DB- 9 connec tor on the Axxius 800.
Axxiu s 800 - R elease 2.2 1-13 Base Platform Control Panel I nterfaces DS1 Connection Ports The DS1 c onnection ports are each e quipped with a st andard RJ-28C (female) on the Axx ius 800 uni t.
1-14 Axxius 80 0 - Rele ase 2.2 Bas e P lat f orm Control Panel I nterfaces Control Pane l Interfac e Card Jumpers The C ont rol Pan el In terf a ce ca rd is pro vid ed w ith a jump er th at allo ws the u ser to pu t a -3 dB p ad in the tr ans mit DS3 si gna l pat h to lo wer th e ou tpu t to a s hor ter li ne le ngt h.
Axxiu s 800 - R elease 2.2 1-15 Base Platform Control Pa nel LEDs Control Pane l L EDs Alarm LEDs LED State Desc ription CRITICAL Off No critical alarms present Red Critical alarms present MAJOR Off No major alarms pr esent Red Major alarm pre sent MINOR Off No minor alarms pres ent Red Minor alarms present ACO Off Normal mode.
1-16 Axxius 80 0 - Rele ase 2. 2 Bas e P lat f orm Contr ol Panel L EDs Ethe rnet LEDs When Sta tus LED is on or flash ing: LED State Desc ription ST ATUS Off Li nk Do wn Green Link Up Flashing Green .
Axxiu s 800 - R elease 2.2 1-17 Base Platform ACO ACO The Ala rm Cutoff f eature per mits t he oper ator to t emporaril y sil ence the al arm out puts while te sting and repai ring the Axxius 80 0. ACO does no t stop al arm messages . Pres sing the ACO pu sh but ton switch disab les the alarm re lays and lig hts the ACO sta tus LED.
1-18 Axxius 80 0 - Rele ase 2.2 Bas e P lat f orm ACO.
C HAPTER Physica l Installation In this Chapter n Unpacking an d Inspection n Installat ion Env ironment n Assemb ly of Axxi us 800 n Rack Mount ing.
2-2 Axxius 800 - Release 2 .2 Physical Instal lation Unpacking and Insp ection Unpa cking an d Inspe ction W ARNING! O BSERVE PRECAUT IONS FOR HANDLING ELEC TROSTATIC DEVICES . 1. Insp ect conta iners for damage d uring shi pment. Repo rt any damag e to t he fre ight carr ier f or pos sible in surance clai ms.
Axxiu s 800 - R elease 2.2 2-3 Physical Installati on Ins tall ati on Env iron me nt Installation Environment The en vironment i n which y ou are ins talling the Axxius 800 must me et the fo llowin g .
2-4 Axxius 800 - Release 2 .2 Physical Instal lation Assem bly o f Ax xius 800 Asse mbly of A xxius 800 The ca rds shou ld be posi tione d accordi ng to t he followi ng guid elines: l Power Su pply(s).
Axxiu s 800 - R elease 2.2 2-5 Physical Installati on Rack Mountin g Rack Mounting The Axx ius 800 c an be mounted on a 19 or 23 i nch ra ck with Ca rrie r Access mounting brac kets. NOTE: The Axxius 800 r equires at l east 3/4 inc hes of free ai r space ab ove and below the chassis ( approx 1/2 RU) for air circu lation.
2-6 Axxius 800 - Release 2 .2 Physical Instal lation Rack Mountin g To maint ain prope r convect ion coo ling, maint ain at l east 1 /2 RU between t he Axxius and any other equip ment ( each Axxius occu pies 3 RU of ra ck spa ce).
C HAPTER Electrical Installation and Cabling In this Chapter n Com plia nt In stalla tion n Chassi s Con nec tions n Power Connect ions n Ext ern al Al arm Inp uts n Visible and A udible Alarms n BITS.
3-2 Axxius 800 - Release 2 .2 Electrical I nstallation and C abling Complia nt Insta llation Compliant Installation W ARNING! A LL TELECOMMU NICATION NET WO RK CONNECTIONS MUST USE MINIMUM 26 AWG WIR E . 1. Mount un it in an a rea that meets En vironment c onditions , see Inst allat ion Environmen t on pag e 2-3.
Axxiu s 800 - R elease 2.2 3-3 Electrical Installation an d Cabling Compli ant Installat ion Ferrite Beads To be com pli ant wi th FC C Part 15 EM I lim its with the Quad DS1 A DP CM se rvi ce ca rd insta lled : l Route alarm c ables sepa rate from th e rear pan el ti p/ring c abling (wire wrap pins ).
3-4 Axxius 800 - Release 2 .2 Electrical I nstallation and C abling Chass is Connect ions Chassis C onnections The fo llowin g illust rations show all connec tors on t he rea r, as well as the front (inter face card) of t he Axxius 8 00.
Axxiu s 800 - R elease 2.2 3-5 Electrical Installation an d Cabling Chas sis Co nne ctio ns Front of the Axxius 800 - I nterf ace Card l 10Base-T Ethe rnet (RJ- 45) l RS-232 Craft Port l DS3-1 and 2 T.
3-6 Axxius 800 - Release 2 .2 Electrical I nstallation and C abling Chass is Connect ions Chassis Ground Connector 1. Route wir e (#6 or #8 AWG co pper) fro m buildi ng ground t o lug on Axxi us 800. 2. Strip ins ula tio n off wire end , if nec essar y .
Axxiu s 800 - R elease 2.2 3-7 Electrical Installation an d Cabling Chas sis Co nne ctio ns Power Connections There ar e thre e power supp lies availabl e with the Axxius 80 0; 24 VDC an d 48 VDC and 48 VDC NI, all use this connector . The Axxiu s 800 su pports a redundan t power sys tem , the ref or e the re i s IN PU T (p ower ) P1 and P2 .
3-8 Axxius 800 - Release 2 .2 Electrical I nstallation and C abling Chass is Connect ions 5. Ensu re th at n o ba re w ire sho ws af ter th e w ire s are ins tall ed. 6. Plug conne ctor in the INPUT ( power) connector , as see n in th e graphic and secu re with se t scre ws.
Axxiu s 800 - R elease 2.2 3-9 Electrical Installation an d Cabling Chas sis Co nne ctio ns External Alarm I nputs The ex ternal a larm input connect or suppor ts 10 a larm input s and is compose d of two 10-pi n connect ors (t wo input pai rs for e ach).
3-10 Axxius 80 0 - Rele ase 2.2 Electrical I nstallation and C abling Chass is Connect ions Visible and Audible Alarms The ex ternal a larm con nectors a re six-p in conne ctors wit h two out put pair s for each alarm le vel ( pins 1 & 2 for minor , pins 3 & 4 f or majo r and 5 & 6 for c ritical a larms).
Axxiu s 800 - R elease 2.2 3-11 Electrical Installation an d Cabling Chas sis Co nne ctio ns BITS Clock 1/BITS Clock 2 The ex ternal a larm connec tors a re three -pin wire -wrap co nnectors. One for each, Tip (T), Ring (R) and Shield (S). Ti p and Ring are the t wo conne ctions fo r the 1 00 ohm diff erenti al sign al to the box.
3-12 Axxius 80 0 - Rele ase 2.2 Electrical I nstallation and C abling Chass is Connect ions Slot (1-8) Wire-Wrap Connector s The Ax xius 800 provid es wir e-wrap c onnect ors fo r each slot ( 1-8) of the unit. Pinou ts are cle arly label ed with the pins.
Axxiu s 800 - R elease 2.2 3-13 Electrical Installation an d Cabling Chas sis Co nne ctio ns Wire-Wrap Pinout for 4 Wire Services Wire -Wrap Pins T1 Name D esc rip tio n 1TX Port 1 Trans mit Ring To D.
3-14 Axxius 80 0 - Rele ase 2.2 Electrical I nstallation and C abling Chass is Connect ions Wire-Wrap Pinout 2 Wire Services Wire-Wrap Pi ns Descri ption T1 Channel 1 Tip R1 Channe l 1 Ri ng T2 Channe.
Axxiu s 800 - R elease 2.2 3-15 Electrical Installation an d Cabling Chas sis Co nne ctio ns Standard Telco Color Code Circ uit connec tions ar e made at the wire- wrap co nnecto rs.
3-16 Axxius 80 0 - Rele ase 2.2 Electrical I nstallation and C abling Chass is Connect ions Pair Pin Locati on Function Color Code 15 40 15 Ti p Cha nne l 15 Ring Ch annel 1 5 Black/Slate Slate/Black .
C HAPTER Configuration In this Chapter n Setting u p a CLI Conn ection n Syst em In fo rma ti on n Basi c System Setup n Quick C onfiguration R elo ad n Setup of DS0 M anagement Chann el.
4-2 Axxius 800 - Release 2 .2 Configur ation Setting up a C LI Conn ection Setting up a CLI Conn ectio n NOTE: The Default IP addres s of the Axxi us 800 Control ler (DS1 o r DS3) is 10.
Axxiu s 800 - R elease 2.2 4-3 Conf ig ur atio n System In formatio n System Information Once a management se ssion h as bee initiated (T eln et or Hyper term) the syste m inf orma tion will b e di sp.
4-4 Axxius 800 - Release 2 .2 Configur ation Ba sic S yste m S etu p Basi c Syste m Setup Initia l Setup Use th e fo llo wing com man ds f or y our in itia l se tup , for fu rth er in fo rma tion s ee th e spec ific com mand list ed in Cha pter 5, CLI Commands.
Axxiu s 800 - R elease 2.2 4-5 Conf ig ur atio n Basi c Sy stem Setu p Set Up Security Use t he followi ng commands to set up the sec urity on t he Axxius 8 00. Set Up IP Addresses for Telnet CLI Use t he followi ng commands to setup T elnet ad dresse s for Co mmand Line I nterfac e (CLI ).
4-6 Axxius 800 - Release 2 .2 Configur ation Ba sic S yste m S etu p Set Up a DS0/Channel Use t he followi ng commands to set up a DS0. Set Up a DS1/T1 Use th e followi ng commands t o set up a DS1/T1. See the set (ds1) command for more deta ils. Command Descri ption set {ds0-addr} type {data|voice} Set the channel type.
Axxiu s 800 - R elease 2.2 4-7 Conf ig ur atio n Basi c Sy stem Setu p Set Up a DS3 Use t he followi ng commands to set up a DS3. See t he se t (ds 3) command for more deta ils. Command Descri ption set {ds3-addr} up Activate the port. set {ds3-addr} id {"id-name"} Set the DS3 ID.
4-8 Axxius 800 - Release 2 .2 Configur ation Ba sic S yste m S etu p Establish a Static Channel Connection Use t he followi ng commands to establ ish a st atic c hannel con necti on. Command Descri ption set {ds3-addr} protect {off|on} Set po rt protect ion on the DS3.
Axxiu s 800 - R elease 2.2 4-9 Conf ig ur atio n Basi c Sy stem Setu p Setup of ADPCM Set Up a V.35 Por t Use t he followi ng commands to set up a V .35 port . Command Descri ption Connect T1 cable to port 1 of the ADPCM serv ice card set {adpcm_card-addr} {none|map1|map2|map3} Enable compres sing by selecting Map t ype.
4-10 Axxius 80 0 - Rele ase 2. 2 Configur ation Ba sic S yste m S etu p Set Up a Single Channel PO TS card Use t he followi ng commands to set up a POTS card . Change the IP Address of the DS0 Management Channe l Use t he followi ng commands to change t he IP over DS0 Manageme nt Channe l for th e Axxius 800.
Axxiu s 800 - R elease 2.2 4-11 Conf ig ur atio n Quick Configu ration Reload Quick Conf iguration Reload The print config command ca n be used as a quick way to reloa d a configurat ion into an Axxius un it, in the ev ent that the con figurat ion has been lost due to software relo ad pr obl ems o r op era tor e rro r .
4-12 Axxius 80 0 - Rele ase 2. 2 Configur ation Quick Conf igurati on Reload 5. Sele ct the [S TART ] but ton, th e window will close and the ope rator wil l be retu rned to th e A xxiu s com ma nd li ne.
Axxiu s 800 - R elease 2.2 4-13 Conf ig ur atio n Quick Configu ration Reload 3. Sele ct the ASCII Setup but ton. 4. Set th e Line delay t o 50 mill iseconds and the Character dela y to 5 mill isecon ds. 5. Sele ct the [O K] butto n back to t he Main Hype rTerminal screen.
4-14 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l Setup of DS0 Managemen t Chann el The DS0 Mana gement Channe l prov ides an al terna tive to t he FDL link f or manageme nt informa tion where FDL is una vailable .
Axxiu s 800 - R elease 2.2 4-15 Conf ig ur atio n Setup of DS0 Mana gement C hannel Equipment Required l Acces s Navigator (versi on 1.7) l (1) Coll ocated Router This exampl e uses a Axxius 800 (version 1.0) with a Axxius TS R card (versi on 1.0) l Remote Axxiu s (1-2 4) Axxiu s 800 (vers ion 1.
4-16 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l The f ollowing i s the Addr ess an d DS1 assign ments us ed in this exa mple.
Axxiu s 800 - R elease 2.2 4-17 Conf ig ur atio n Setup of DS0 Mana gement C hannel Set IP Conf igura tion of PC 1. Set IP Addr ess t o 192.168. 201.102 2.
4-18 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l Add and Enable a ll Remote Axxius Needed Telnet into the TSR card 1. From the CLI execut e a Telnet command to the TSR card . Telne t {slot} Example: telnet 1 The example will Teln et into t he rout er locat ed in slot 1.
Axxiu s 800 - R elease 2.2 4-19 Conf ig ur atio n Setup of DS0 Mana gement C hannel Configure Trunk Connections 1. Sele ct Configura tion < Profile Directory > -> from th e Rou ter Main Menu and select [ E NTER ] . 2. Sele ct Router CARD <Setup - > from th e Pr ofil e wi ndo w a nd s ele ct [ E NTER ] .
4-20 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l 4. For al l WAN port numb ers alrea dy assigne d a DS0 for management sel ect < Frame-Relay 1490 > as the WAN c onnections type. 5. Sele ct the PVC Management as < Disable d > .
Axxiu s 800 - R elease 2.2 4-21 Conf ig ur atio n Setup of DS0 Mana gement C hannel 3. Set t he follo wing on t his sc reen: Sele ct the IP Protocol Eth II (X), all ot hers shou ld not be select ed. Set t he LAN Networks Updates for IP and IPX to < Neither > .
4-22 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l 2. Set t he follo wing on t his sc reen: Rename RemoteUnit (de fault name) t o Axxius1 . Set WAN Netwo rks Updates for IP to <Never> . Set WAN IP: Numbered to <No > .
Axxiu s 800 - R elease 2.2 4-23 Conf ig ur atio n Setup of DS0 Mana gement C hannel 6. Set De vice Name to Axxius1 Set t he IP Address to 192.168.202.1 (Axxi us1 WAN addre ss) Set t he Subnet Mask to 255.255.255.255 Set t he M etric to 1 7. Sele ct [E SC ] t o exit and <Yes> to save chan ges.
4-24 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l 9. Sele ct the following on thi s scre en: At the Selec t WAN Port Number: < None> , scroll from None to 1 (which is th e rem ote Axxi us1 ). Set DLCI to 16 .
Axxiu s 800 - R elease 2.2 4-25 Conf ig ur atio n Setup of DS0 Mana gement C hannel Reinitiali ze the Router 1. Sele ct Exit <R einitial ize > from the Ro ute r mai n window and s elect [E NTER ] . 2. Sele ct < YES > and sele ct [E NTER ] to Rei niti aliz e th e TSR Ca rd.
4-26 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l Configuration of Remote Axxius Note: The Et hernet cannot be conn ected to t he Remote Axx ius during th e setu p of the DS0. Use t he followi ng commands to setup the IP o ver DS0 Management Channel for each Remote Axxius 8 00 .
Axxiu s 800 - R elease 2.2 4-27 Conf ig ur atio n Setup of DS0 Mana gement C hannel Configuration of Access Navi gator Note: The Et hernet cannot be conn ected to t he Remote Axx ius during th e setu p of the DS0. The fo llowing se tup, cr eates a path from th e Axxius Rout er to the remo te Axxius.
4-28 Axxius 80 0 - Rele ase 2. 2 Configur ation Set up of DS 0 Ma nage m ent C hanne l Testing the DS0 M anagement Channel Afte r the DS0 management cha nnels has bee n setup wit h one Remote Axxius, te st the manageme nt channel . 1. PING 192.168.20 2.
C HAPTER CLI Commands In this Chapter n Command Line Interface Help n CLI Comman ds.
5-2 Axxius 800 - Release 2 .2 CLI Comman ds Command Line Interfa ce He lp During a CLI session, help is available at any time. ? or hel p Type a ? (or "help" before a command) at any time for quick command information > add ? add ........
Axxiu s 800 - R elease 2.2 5-3 CLI Comman ds the [TAB] feature, scro ll through a ll available o ptions for this command: > set [TAB] will scroll through the set co mmands, with each <TAB> > set alarms [TAB] > set autoexit [TAB] > set clock1 .
5-4 Axxius 800 - Release 2 .2 CLI Comman ds CLI Commands For maneuverability through these commands , all co mmand names in blue or itali cs are hyper linked.
Axxiu s 800 - R elease 2.2 5-5 CLI Comman ds aco (Alarm Cut Off) aco (Ala rm Cut Off) Use the aco command to activate the Alarm Cut Off, which opens the alarm relay contacts on the back of the unit.
5-6 Axxius 800 - Release 2 .2 CLI Comman ds add add Use the add command to create us ers, interfaces, serv ices or profiles . See the following sectio ns for detailed informatio n on the following add.
Axxiu s 800 - R elease 2.2 5-7 CLI Comman ds add add (ds1 ) ais Use the ad d (d s1 ) ais command to add DS1s to a list for the AIS Forwardin g feature. The DS1 enabled for AIS forwarding will be checked against th e DS1s defined in the list. Note: If no list is d efined, AIS will go to all the DS1s cros s-co nnected to that DS1.
5-8 Axxius 800 - Release 2 .2 CLI Comman ds add add (router) dhcp server option Use the ad d (route r) dhcp ser ver opti on command to a dd opti onal DHCP serv er attri butes t hat will b e advert ised ev ery time a DHCP cl ient d iscovery i s init iated.
Axxiu s 800 - R elease 2.2 5-9 CLI Comman ds add add (router) dns proxy Use the add ( router) dns pro xy command to enable DNS proxy an d add a remote DNS serve r address to the s pecified Router card.
5-10 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router) snmp community Use the add (router) sn mp community command to add a SNMP community to an interface on the specified Router car d.
Axxiu s 800 - R elease 2.2 5-11 CLI Comman ds add add (router) snmp trap Use the add (r outer ) snm p trap command to specify a destin ation to send SNMP trap messages for the specified Router car d.
5-12 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router) st atic dns host Use the add (router) stat ic dns host command to add a static DNS host reco rd for resolving a domain name to an IP addr ess if the DNS se rver cannot pro vide the information.
Axxiu s 800 - R elease 2.2 5-13 CLI Comman ds add add (router) uploaduser Use the add (rout er) uploa duser command to specify a host that is allowed to upload either the conf iguration or software files to the specified Router card.
5-14 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router- lan) filter Use the add (router-lan) f ilter commands to add filters to the specified LAN interface. add (r outer-lan) filter address Use the add (router-lan) f ilter address command to add an address filter to the table of Layer 2 filters applied to the specified LAN interface.
Axxiu s 800 - R elease 2.2 5-15 CLI Comman ds add add (r outer-lan) filter custom Use the add (router-lan) f ilter custom command to add a custom f ilter to the table of Layer 2 filters applied to the specified LAN interface.
5-16 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add Ethernet Frame and IP Packet Format Ethernet 802.3 (raw) Frame - D atalin k Header 6 by tes 6 by tes 2 by tes 46 to 1500 b ytes 4 byt es Dest MAC Sour.
Axxiu s 800 - R elease 2.2 5-17 CLI Comman ds add add (r outer-lan) filter protoc ol Use the add (router-lan) f ilter protocol command to add a pr otocol filter to the table of Layer 2 filters applied to the specified LAN in terface. Note that you only need to iden tify either an Ethe rnet or IEEE value, but not both.
5-18 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-lan) se condary ip address Use the add (r outer- lan) s econdary ip address command to add a secondary IP ad dress and subnet to the s pecified LAN interface.
Axxiu s 800 - R elease 2.2 5-19 CLI Comman ds add add (router- lan) static Use the add (r outer- lan) stati c commands to add s tatic elements on the s pecified LAN interface.
5-20 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-l an) static ip networ k Use the add (router-lan) static ip network command to add a static IP n etwork (r oute) to the specified LAN interf ace. Synt ax: add {rtr_lan-addr} stati c ip network {ip-addr} { mask} {next-hop-ip-addr} [metric] Exampl e: add 3:1 static ip network 195.
Axxiu s 800 - R elease 2.2 5-21 CLI Comman ds add add (route r-lan) stati c ipx network Use the add ( router-lan) stati c ipx network command to add a static IP X network (ro ute) to the specified L AN interface.
5-22 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-l an) static mac addr ess Use the add (rou ter-lan) sta tic ma c address command to add a static MAC address to the table of learned addresses on the specified L AN interface. This command is typically used in bridg ing.
Axxiu s 800 - R elease 2.2 5-23 CLI Comman ds add add (router-wan) firewall Use the add (router-wan) f irewall command to add a firewall rule to a WAN.
5-24 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add {s ervi ce } {d est -ip -ad dr/b its} The destin ation IP Addr ess and n umber of signi ficant bits. The IP Address i s in the form of xxx.xxx .xxx.xx x, where xxx i s between 0-255. The ad dress "0.
Axxiu s 800 - R elease 2.2 5-25 CLI Comman ds add {src-ip-addr/bits } The destination IP address and n umber of si gnificant bits. The address "0.0.0.0/0" matches any addres s. src-ip-addr Enter the IP Address o f the remote device or network that this rule will affect.
5-26 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-wan) gre network Use the add (router-wan) gre network command to add a "by net work" Gener ic Route Encapsulation (GR E) tunnel to a WAN.
Axxiu s 800 - R elease 2.2 5-27 CLI Comman ds add add (router-wan) nat bypass Use the add (ro uter-wan) nat bypass command to add subnets to the list of source add resses that will not be subject to NAT tran slation when passing through a NAT enabled WAN interface.
5-28 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-wan) static Use th e ad d (router-wa n) static commands to add static elements on the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-29 CLI Comman ds add add (route r-wan) static ip net work Use the add (r outer -wa n) st atic ip ne twor k command to add a static IP network (rou te) to the specified WAN interface.
5-30 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-wan) static ipx network Use the add (router- wan) stat ic ipx network command to add a static IPX networ k (route) to the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-31 CLI Comman ds add add (route r-wan) static mac address Use the add (r outer- wan) st atic mac address command to ad d a static MAC address to the table of learned addres ses on the specifi ed WAN interface. This command is typically used i n bridging .
5-32 Axxius 80 0 - Rele ase 2.2 CLI Comman ds add add (router-wan) static nat address Use the add (rout er-wan) stat ic nat ad dress command to add a static NAT bi-directional mapping to the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-33 CLI Comman ds alarm s alarms Use the alarm s comman d to display the active alarms. The report can be filtered by address, category and/o r severity (major, minor , alert). The alarm s command alone, displays a full alar m report.
5-34 Axxius 80 0 - Rele ase 2.2 CLI Comman ds clear clear User the clear command to clear logs, performance data and tables. clea r (ds1) clea r (ds3) clea r key clea r log clea r (ocudp) per formance.
Axxiu s 800 - R elease 2.2 5-35 CLI Comman ds clear clea r (ds1) Use the clear (ds1) com mand to clear specified DS1 per formance da ta. Synt ax: clear {ds1-addr} performance {setting} Exampl e: clear a:1 performance all Clears all perfo rmance data o n DS1 1 (po rt 1) on the DS1 C ontroller card.
5-36 Axxius 80 0 - Rele ase 2.2 CLI Comman ds clear clea r (ds3) Use the clear (ds3) com mand to clear specified DS3 per formance data. Note this command app lies only whe n using a DS3 Contro ller card.
Axxiu s 800 - R elease 2.2 5-37 CLI Comman ds clear clea r key Use the clear key command to remove a sp ecific keyed feat ure. To acqu ire a feature key code, contact Carrier Access Customer Service.
5-38 Axxius 80 0 - Rele ase 2.2 CLI Comman ds clear clear (router) ip address table Use the clear (router) ip address table com mand to flush the learned entries fr om the IP address tabl e for the specified inte rface from the specified Router car d.
Axxiu s 800 - R elease 2.2 5-39 CLI Comman ds clear clear (router) performance Use the clear (router) performance command to clear the runtime statistics that are displayed by th e status ( router) performance co mmand. This co mmand ta kes effe ct immediately.
5-40 Axxius 80 0 - Rele ase 2.2 CLI Comman ds connect connect Use the connect command to create two-way connections between any DS0 channels of the service or controller cards. Synt ax: connect {slot:port|slot:port:channel} {slot:port|slot:port:channel} Use the disconnect command to delete connections.
Axxiu s 800 - R elease 2.2 5-41 CLI Comman ds connect connec t (router-trunk) (t 1) Use the connect (router-t runk) (t1) command to create two-way connections between the Router port trunk connection s and any DS 0 channels of the servi ce card or C ontroller .
5-42 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete Use the delete command to r emove users , interfaces, services o r profiles. See the following sectio ns for detailed informatio n on the f.
Axxiu s 800 - R elease 2.2 5-43 CLI Comman ds delete delete ( ds1) ais Use the delete (ds1 ) ais command to delete DS1s from the AIS DS1 list. The DS1 that is AIS enabled will be checked against the DS1 s defined in the list. Note: If no DS1s are defi ned, and AIS is enabled , the default will b e all the DS1s in the system.
5-44 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete (router) dhc p server option Use the delete ( router) dhcp server option command to delete optional DHCP server attributes that will be advertised every time a DHCP clien t discovery is in itiated.
Axxiu s 800 - R elease 2.2 5-45 CLI Comman ds delete delete (router) remote Use the delete (router) remot e command to delete a remote WA N profile from the WAN profile table on th e specified Router card.
5-46 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete (router) snmp trap Use the delete (router) s nmp trap command to delete a trap destinatio n from the specified Router card. Synt ax: delete {rtr_card-addr} snmp trap {"community-name"} {ip-addr} Exampl e: delete 2 snmp trap "commune" 192.
Axxiu s 800 - R elease 2.2 5-47 CLI Comman ds delete delete (router) uploaduser Use the delete (router) uploadus er command to remove an existing host th at is allowed to upload either the configuration or softwa re files to th e specified Router card.
5-48 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delet e (rout er-la n) fi lter Use the delete (router-lan) f ilter command to delete a sin gle filter rule from the tabl e of Layer 2 filters applied to the specified LAN interf ace.
Axxiu s 800 - R elease 2.2 5-49 CLI Comman ds delete delete (router-lan) se condary ip address Use the delete (router-lan) secondary ip address command to delete a secondary IP add ress and subn et to the specified LAN interf ace.
5-50 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete (rout er-lan ) static Use the de lete (router-la n) static commands to delete s tatic elements from the specified LAN interface.
Axxiu s 800 - R elease 2.2 5-51 CLI Comman ds delete delete ( router-lan) static ip networ k Use the de let e (ro ute r- lan) sta tic ip ne two rk command to delet e a static IP net work fr om the specified LAN interf ace.
5-52 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete ( router-lan) static ipx network Use the delete (router-lan) static ipx network command to delete a static IPX network (route) to the specified LAN interf ace.
Axxiu s 800 - R elease 2.2 5-53 CLI Comman ds delete delete ( router-lan) s t atic ma c address Use the delete (router-lan) static mac address command to delete a static MAC address entry to the specified LAN interface.
5-54 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete (router-wan) gre network Use the delete (router-wa n) gre network co mmand to d elete a " by netw ork" GRE t unnel to a WAN . Synt ax: delete {rtr_card-addr} {"wan-name"} gre network {ip-addr mask|ip-addr/bits} Exampl e: delete 3 "LosAngeles" gre network 10.
Axxiu s 800 - R elease 2.2 5-55 CLI Comman ds delete delete (rout er-wan ) static Use the delete (router-wan) static commands to delete a static element fr om the WAN interface. delete ( router-wa n) static ip addr ess Use the delete (router-wan) static ip address command to delete a st atic IP address on the specified WAN interface.
5-56 Axxius 80 0 - Rele ase 2.2 CLI Comman ds del ete delete ( router-wa n) static ip net work Use the delete (router-wan) static ip networ k command to delete a static IP network from the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-57 CLI Comman ds delete delete ( router-wa n) static mac address Use the delete (router-wan) static mac addres s command to delete a static MAC add ress entry from th e specified WAN interface.
5-58 Axxius 80 0 - Rele ase 2.2 CLI Comman ds discon nect delete user The delete user command will remover a user created by the add user command. Synt ax: delete user {"user-name"} Exampl e: delete user "jsmith" {"user -nam e"} The user-n ame is an existing user I D in the system.
Axxiu s 800 - R elease 2.2 5-59 CLI Comman ds exit exit Use the exit com mand to log out o f the Command Line I nterface (CLI). Synt ax: exit Exampl e: > exit Logging out of Carrier Access - Axxius.
5-60 Axxius 80 0 - Rele ase 2.2 CLI Comman ds load load W ARNING! B EFORE LOADING A DOWN - LEVEL OF R OUTER CODE TO AN A DIT , SAVE THE CONFIGURATI ON TO A FILE .
Axxiu s 800 - R elease 2.2 5-61 CLI Comman ds load load x modem Use the loa d xmodem comman d to down load softwa re via Xmod em. This c ommand is onl y available with an RS-232 connectio n.
5-62 Axxius 80 0 - Rele ase 2.2 CLI Comman ds log log log Displays the event log. W here the optional [slo t:port:ch annel], [categor y], and [severity] are variabl es used to narrow do wn the log di splay ed. The log command wit hout any op tions displays a full log.
Axxiu s 800 - R elease 2.2 5-63 CLI Comman ds ping ping ping Use the ping command to perform a ping test f rom the Controller and repor t the result. If the host is reachable, each individual response will be di splayed. Synt ax: ping {ip-addr} [count] [length] Exampl e: ping 192.
5-64 Axxius 80 0 - Rele ase 2.2 CLI Comman ds prin t print Use the print command to display the help information or print th e configuration file. Synt ax: print {config|help} print config Print the configuration file for the Axx ius 800.
Axxiu s 800 - R elease 2.2 5-65 CLI Comman ds rena me (router ) print help Print the complete help file to the screen. Synt ax: print help Exampl e: print help This example would print the entir e help text, which can be scrolled though with Ente r or Spacebar .
5-66 Axxius 80 0 - Rele ase 2.2 CLI Comman ds rese t reset rese t (contro ller ) Use the res et (controller) co mmand to r eboot the sy stem. Reset alone will reb oot the en tire system . Synt ax: reset [ctrlr-addr|active|standby] Exampl e: reset a1 Will reset th e controller in the controller slo t 1.
Axxiu s 800 - R elease 2.2 5-67 CLI Comman ds resto re reset (r outer) coldboot Use the reset (router) co ldboot command t o reboot the Router. This will reboot includin g a power cycle to the R outer card. Synt ax: reset {rtr_card-addr} coldboot Exampl e: > reset 2 coldboot OK The exampl e will coldboot the Router card in slot 2.
5-68 Axxius 80 0 - Rele ase 2.2 CLI Comman ds rtrping rtrping Use the rtrping command to request that the Router per form a ping tes t and report the r esult. Synt ax: rtrping {rtr_card-addr} {dest-ip-addr|"domain-name"} [count] [count length] [count length source-ip-addr] Exampl e: rtrping 4 192.
Axxiu s 800 - R elease 2.2 5-69 CLI Comman ds set set set alarms set (ocudp ) baud se t auto exi t set (ocu dp) loop bac k set (b ri) set ( ocudp) l oopdetect se t (bri ) mo de set (ocu dp) mve c set .
5-70 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set se t (ro uter -lan ) ip ad dre ss set (ro uter- wa n) n at se t (rou ter -lan ) ip x net wo rk set (ro uter- wa n) o ther se t (ro uter -l an) ph y se.
Axxiu s 800 - R elease 2.2 5-71 CLI Comman ds set set al arms Use the set alar ms to manually set an alarm state for testing. Synt ax: set alarms {critical|major|minor} {off|on} Exampl e: set alarms critical on The example set th e alarm state of critical on.
5-72 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set (bri) Use the set (br i) command to setup the I SDN BRI card. Synt ax: set {bri-addr} {day|hour} {es|ses} {value} Exampl e: set 3:4 threshold day ses 30 To set t he daily thr eshold t o 30 Severel y Errored Seco nds on p ort 4 of a BRI card in slot 3.
Axxiu s 800 - R elease 2.2 5-73 CLI Comman ds set set (bri) mode Use the set (b ri) mod e command to set the mod e for the ISDN BRI Service. Synt ax: set {bri_card-addr} mode {setting} Exampl e: set 4 mode nt3ds0 To set the BRI card in slot 4 to use 3 DS0 LUNT {bri_ca rd- addr} The slot num ber (1-8) of the Adit chassis that contains the BRI card .
5-74 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set ccl abel Use the set cclable command to s et a user defined cro ss-connect label. Synt ax: set cclabel {addr} {"label"} Exampl e: set cclabel a:1:1 "Idle Ch" The example will se t a user connect label "Id le Ch" on the DS0 a:1:1 .
Axxiu s 800 - R elease 2.2 5-75 CLI Comman ds set set clock ( 1 and 2) Use the set clock (1 an d 2) command to set the master transmit clock. The primary master clock source may be used to clock each DS1 transmitter. Th e clock circuit automatically switches to the secondar y clock source if the p rimary clock fails.
5-76 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set (ds0) Use the set (ds 0) command to setup one or all DS0s in a DS1. The command specifies DS0 or range o f DS0s, and the setti ng to app ly. set(ds 0) signal Use the set (d s0) sign al comman d to setup on e or all DS0s in a DS1 signal.
Axxiu s 800 - R elease 2.2 5-77 CLI Comman ds set set(ds 0) type Use the set (d s0) type co mmand to s etup one o r all DS0s in a DS1 signal t ype. Synt ax: set {ds0-addr} type {data|voice} Exampl e: set 3:1:1-4 type voice To set th e traffic type to voice o n channels 1-4 on po rt 1 of s lot 3 on a service card.
5-78 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set (ds1) Use the set (d s1) command to set up DS1 interfaces. The command specifies a ra nge of interfaces and the setting to apply. Synt ax: set {ds1-addr} {setting} Exampl e: set a:1 framing esf To set DS 1 1 (p ort 1) o n a DS1 Contr oller to u se ESF f raming.
Axxiu s 800 - R elease 2.2 5-79 CLI Comman ds set id Set the DS1 circuit identifi cation name. This is th e same as d sx1Circuit Identifier from DS1 MIB t ransmission vendor ’s identificati on.
5-80 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set threshol d Set defa ult t hresho lds for a DS1. Defaul ts for a ll are 0. day Set threshold for a daily in terval bes Burst y errore d seconds range: .
Axxiu s 800 - R elease 2.2 5-81 CLI Comman ds set set (ds1 card) Use the set (d s1 c ard) commands to conf igure DS1 card types. These co mmands apply to the Quad DS1/E1 (hard ened) and Quad DS1 ADPCM (hardened) service cards.
5-82 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set (ds1 card) a dpcm map Use the set (d s1 car d) a dpcm ma p command to set vo ice compression map on the Quad DS1 ADPCM card. Synt ax: set {adpcm_card-addr} adpcm {none|map1|map2|map3} Exampl e: set 5 adpcm map1 {adpc m_ca rd-ad dr} - The slot number (1-6) th at contains the Quad DS1 ADPCM card.
Axxiu s 800 - R elease 2.2 5-83 CLI Comman ds set set (ds3) Use the set (d s3) command to set up DS3 interfaces. The command specifies a ra nge of interfaces and the setting to apply. Synt ax: set {ds3-addr} {setting} Exampl e: set a:1 framing m23 To set DS3 1 (port 1) on a DS3 Controller ( slot A) to use M23 framing.
5-84 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set frame Set the DS3 frame PMDL ID st ring Command synt ax: s et {ds 3-addr} frame {"string"} {"string"} = transmis sion ven dor’s identificat ion, up to 10 char acters, enclosed in quotes .
Axxiu s 800 - R elease 2.2 5-85 CLI Comman ds set reversion Set pro tection r eversion on the D S3 off Dis able protect ion revers ion of lo opback r equests on En able prot ection rever sion of loopback r equests threshold Set defe ct thr esholds f or a DS3.
5-86 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set ethe rnet ip addres s Use the set ethernet ip address command to set the E thernet address for the Axxius 800. Synt ax: set ethernet ip address {ip-addr} [mask] Exampl e: set ethernet ip address 172.
Axxiu s 800 - R elease 2.2 5-87 CLI Comman ds set set (f xo) Use the set (f xo) command to s etup one or all of the voice channels of a n FXO card. The command specifies the list of voice channels within that card , and the setting to apply.
5-88 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set (f xsPS or fxs PSM ) Use the set ( fxsPS or fxsPSM) command to setup voice channels of an Single Channel POTS card (FXS PS) or th e POTS card with modem (F XS PSM). The command s pecifies the list of voice channels, and the setting to apply.
Axxiu s 800 - R elease 2.2 5-89 CLI Comman ds set set idle Use the set idle command to se t the system-wide idle code s ent on DS0s. Synt ax: set idle {pattern} Exampl e: set idle 0xff {patte rn} A hexadecimal number with a range from 0x00 to 0xff. This number mus t be preceeded by 0x.
5-90 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set ipds0 Use the set ipds0 command to setup t he DS0 manag ement channel . Note: the DS0 selected as the DS0 management chann el can only r eside on the Co ntroller T1.
Axxiu s 800 - R elease 2.2 5-91 CLI Comman ds set set key Use the set key command to enable a specific keyed f eature. To acquire a feature key code, contact Carrier Access Cust omer Service. Curr ently, keyed features (if available) can be enabled on a Con troller or a Router.
5-92 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set login support Use the set login support command to enable or d isable the internal login accounts for Carrier Access Suppo rt personnel for th e Controller and Rou ter cards.
Axxiu s 800 - R elease 2.2 5-93 CLI Comman ds set set lsprot ect en able /dis able Use the set lsp rotect enable/disable comman d to set the global enable or disable the Low Speed Protection option s on the system.
5-94 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set lsprotec t nonrevertive Use the set lsprotect nonrevertive command to set low speed prot ected port(s ) to non-re vertive mode. When a port is in no n-revertive mode and a failu re occurs th e port is switched to the protection port, and will remain ther e until manually res et.
Axxiu s 800 - R elease 2.2 5-95 CLI Comman ds set set lsprotect remove Use the set lsprotect remove co mmand to remove port from protect ed mode. Synt ax: set lsprotect {slot:port} remove Exampl e: set lsprotect 5:2 remove Do you really want to do this? y *-Protected port(s) no t removed since they were not pre viously assigned.
5-96 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set lsprotect revertive Use the set lsprotect revertive command to s et low speed protected port(s ) to revertive mode. When a port is set to rever tive mode and a failure occurs the port is swit ched to the protection port.
Axxiu s 800 - R elease 2.2 5-97 CLI Comman ds set set (ocudp) baud Use the set (ocu dp ) bau d command to co nfigure the Baud Rate for OCU-DP por ts. Synt ax: set {ocudp-addr} baud {rate}[sw56|sw56cp] Exampl e: set 3:2 baud 2400 Set the b aud rate on port 2 to 240 0, on the O CU-DP card in s lot 3.
5-98 Axxius 80 0 - Rele ase 2.2 CLI Comman ds set set (ocudp) loopback Use the set (ocu dp ) loopback command to manually se t OCU/CSU loopback test s. Synt ax: set {ocudp-addr} loopback {csu|ocu} {loopdown|loopup} Exampl e: set 3:2 loopback csu loopdown {ocudp-addr } The {slot:port} addres s of the OCU-DP card yo u want to apply the changes to.
Axxiu s 800 - R elease 2.2 5-99 CLI Comman ds set set (ocudp) loopdetect Use the set (ocu dp ) loopdetect to conf igure the OCU n on-latch ing/lat ching l oopback code detection.
5-10 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (ocudp) mvec Use the set (ocu dp ) mvec to set Majority Vote Error Correction (MVEC). Synt ax: set {ocudp-addr} mvec {disable|enable} Exampl e: set 3:2 mvec enable {ocudp-addr } The {slot:port} addres s of the OCU-DP card yo u want to apply the changes to.
Axxiu s 800 - R elease 2.2 5-10 1 CLI Comman ds set set (ocudp) selftest Use the set (o cudp) selftest to initiate the OC U-DP card to per form a self test . This reque st will display a m essage to wait 8 seconds bef ore requesting s elftest status w ith the statu s command.
5-10 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) autologout Use the set (router) autologout command to set the perio d of time of inactivity after which the user will be automatically logged-out of a Telnet session.
Axxiu s 800 - R elease 2.2 5-10 3 CLI Comman ds set set (router) dhcp Use the set ( router) dhcp commands to config ure the DHCP functions. set (rout er) dhcp di sable Use the set (router) dhcp disable command to d isable both DHCP server an d DHCP relay functionality for the specified Router card .
5-10 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) dhcp se rver dnsser ver Use the set (router) dhcp server dnsserver command to set the IP address of up to 4 DNS servers that the DHCP server will inform the clients of . Synt ax: set {rtr_card-addr} dhcp server dnsserver {number} {ip-addr} Exampl e: set 5 dhcp server dnsserver 4 122.
Axxiu s 800 - R elease 2.2 5-10 5 CLI Comman ds set set (rout er) dhcp se rver dur ation Use the set (router) dhcp server duration command to s et the lease duratio n that the DHCP server appl ies to client assignments.
5-10 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) dhcp server netbios nodetype Use the set (router) dhcp server netbios nodetype co mmand to set the NetBIOS n ode type (s ee RFC 10 01/1002) that the DHCP server p rovides to clients .
Axxiu s 800 - R elease 2.2 5-10 7 CLI Comman ds set set (rout er) dhcp se rver st artaddr Use the set (router) dhcp server st artaddr command to enable the DHCP serv er on the specified Router card . Synt ax: set {rtr_card-addr} dhcp server startaddr {ip-addr} {count} Exampl e: set 4 dhcp server startaddr 134.
5-10 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) dns Use the set ( router) dns commands to set Domain Name Server (DNS) options . set (rout er) dns domai n Use the set (r ou ter) dns dom ai n command to set the default domain that the DNS resolver will add to any name queries that are not fully qualified.
Axxiu s 800 - R elease 2.2 5-10 9 CLI Comman ds set set (rout er) dns r esolver Use the set (router) dns resolver command to enab le/disable use of DNS resolver to conver t domain names to IP addresses . The DNS server address must be set bef ore the DNS resolver can be enabled.
5-11 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) enhanced security Use the set (router) enhanced security command to enable or dis a ble enhanced log in security on the TSR. When enabled the user will not receive any login prompt or other output until the security password is typed.
Axxiu s 800 - R elease 2.2 5-11 1 CLI Comman ds set set (router) lmi poll Use the set (router) lmi poll command to specify the Local Man agement Interf ace (LMI) for the specified Router card.
5-11 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) login prompt Use the set ( router) lo gin prompt command to enable/disable the login prompt on the specified Router card .
Axxiu s 800 - R elease 2.2 5-11 3 CLI Comman ds set set (router) ntp poll Use the set (router) ntp po ll command to specify p olling of the NTP s erver every d efined number of seconds.
5-11 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) ntp timezone Use the set (router) ntp timezone command to specify the timezone offset relative to GMT for this TSR.
Axxiu s 800 - R elease 2.2 5-11 5 CLI Comman ds set set (router) port Use the set (router) port command to s et port characteris tics on a Terminal Server Ro uter (TSR) card . set (rout er) port baudrate Use the set ( router) port baudrate command to set the baud rate on a TSR port.
5-11 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) port databits Use the set ( router) port databit s command to set the data bits on a TSR port. Synt ax: set {tsr_card-addr} port {port-number} databits {5|6|7|8} Exampl e: set 5 port 2 databits 6 The example will set the data bits to 6 on the port 2 on th e TSR card in slot 5.
Axxiu s 800 - R elease 2.2 5-11 7 CLI Comman ds set set (rout er) port flowcontrol Use the set (router) port flowcontrol com mand to set the f low control on a TSR port.
5-11 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) port inacti vity ti mer Use the set ( router) port inac tivity ti mer command to set the inactivity tim eout for a RS-232 sessio n. This setting can be issued when the card is physically strapped f or Ethernet, bus has no effect.
Axxiu s 800 - R elease 2.2 5-11 9 CLI Comman ds set set (rout er) port name Use the set ( router) port name command to set d efine name f or a TSR port.
5-12 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) port passive Use the set ( router) port passive com ma nd to se t th e TS R p ort to p ass ive. T his co mman d will terminate any active telnet connection on this in terface and will reinitialize its associated TCP socket.
Axxiu s 800 - R elease 2.2 5-12 1 CLI Comman ds set set (rout er) port prompt Use the set (router) port prompt command to set the authentication pro mpt on a TSR port.
5-12 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) port stopbits Use the set (router) port stop bit s command to set the numb er of stop bits on a TSR port. The stop bit is an interval at the end of each Asynch ronous Character that allows the receiving co mputer to paus e before the star t of the next c haracter.
Axxiu s 800 - R elease 2.2 5-12 3 CLI Comman ds set set (rout er) port tbos map displ ay Use the set ( router) port tbos map di splay command to set a TBOS (Telemetry Byte Oriented Serial) display map value for o ne of the eight TBOS display availab le for monitoring equi pment.
5-12 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) port type Use the set ( router) port type co mmand to set the appli cation bei ng used fo r a RS-232 (serial) port. This setting can be issu ed when the card is physically strapped for Ethernet, but has no effect.
Axxiu s 800 - R elease 2.2 5-12 5 CLI Comman ds set set (router) ppp auth Use the set ( router) pp p auth command to confi gure the PP P (Poi nt-to-Po int Prot ocol) authentication on th e specified Router card.
5-12 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) ppp auth byremote user Synt ax: set {rtr_card-addr} ppp auth byremote user {profilename|"protocol-name"} Exampl e: set 5 ppp auth byremote user profilename The example wil l set the PPP authent ication user nam e for the Router in slot 5 to equal the profile nam e.
Axxiu s 800 - R elease 2.2 5-12 7 CLI Comman ds set set (router) ppp security Use the set (router) ppp security command to set up the local external security se rver, that the Router will use to authen ticate remote PPP devices.
5-12 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er) ppp sec urity server Synt ax: set {rtr_card-addr} ppp security server {none|radius|tacacs} Exampl e: set 5 ppp security server none The example will s et the Router in slot 5 to not use an ex ternal security server to authenticate r emote PPP devices.
Axxiu s 800 - R elease 2.2 5-12 9 CLI Comman ds set set (router) proxy Use the set (rou ter) proxy co mmand to enable/disab le proxy ARP mode on the Rout er. This command will add an IP interface between th e Controller and the R outer over the backplane.
5-13 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set There are numerous cas es of IP addr ess assign ments for the proxy and eac h case ca uses slig htly differen t behav ior: Proxy address is in the same subnet as the Controller LAN address.
Axxiu s 800 - R elease 2.2 5-13 1 CLI Comman ds set set (router) reboot Use the set ( router) reboot command to set automatic rebo ot after an u pload of code o r configuration f ile.
5-13 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) s nmp Use the set (ro ute r) snm p command to set the SNMP contact, lo cation and name on the specified Router card . set (router) snmp contact Use the s et (router) snmp contact command to set the valu e of sysContact o n the specified Router card.
Axxiu s 800 - R elease 2.2 5-13 3 CLI Comman ds set set (router) snmp name Use the set (ro uter) snmp name comman d to set the value of sysName on the specified Router card.
5-13 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) s tp Use the set (ro ute r) st p commands to con figure the Spanning Tree Protocol on the Rou ter. Note : Enter {slot} only, if {slot:port} is entered th e command will be directed to the Router LAN and no t the Router Card.
Axxiu s 800 - R elease 2.2 5-13 5 CLI Comman ds set set (router) stp bridge maxage Use the set (rou ter) stp brid ge maxage co mmand to conf igure Spanni ng Tree maxim um age value for th e bridge. T he bridge max age v alue specifies the maximum age of received protoco l informat ion befo re it is discarded.
5-13 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router) stp enable/disabl e Use the set (router) stp ena ble/disable command to enab le and disabl e Spanning Tree Prot ocol on th e Rout er. Synt ax: set {rtr_card-addr} stp {disable|enable} Exampl e: set 3 stp enable The example will en able Spanning Tree o n the Router in sl ot 3.
Axxiu s 800 - R elease 2.2 5-13 7 CLI Comman ds set set (router) s yslog Use the set (rout er) syslo g commands to configure th e Rout er to send alarm and event messag es to a Syslog s erv er.
5-13 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (route r) syslog level Use the set (r outer) syslo g leve l command to set the Syslog severity level . Events of all severity levels lo wer in number (more severe) will be se nt to the Syslog server.
Axxiu s 800 - R elease 2.2 5-13 9 CLI Comman ds set set (router-la n) filter forwar d Use the set (router-lan) filter forward command to specify the f orwarding mode for Lay er 2 filters on the LAN interface.
5-14 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-la n) framing Use the set ( router-lan) framing command to s pecify which Ethe rnet frame types ar e suppor ted on the LAN interface.
Axxiu s 800 - R elease 2.2 5-14 1 CLI Comman ds set set (router-la n) gateway Use the set ( router-lan) gateway co mmand to specify a d efault IP gateway for the s pecified LAN interface. If there is no static network entry to 0.0.0 .0, then this add ress is used a s the default gateway for packets with no explici t route.
5-14 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-la n) ip address Use the set (router-lan) ip address command to specif y an IP address for the specified LAN interface. When first installed the Router car d’s LAN interf ace has a de fault IP address of 10.
Axxiu s 800 - R elease 2.2 5-14 3 CLI Comman ds set set (router-la n) ipx network Use the set (rou ter-lan) ipx net work command to specify I PX network numbers fo r the four IPX LAN frame types. This enables the Axxius to Ro uter IPX to Remote (WAN) net works, even if an IPX server does not exist o n the local LAN.
5-14 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-la n) phy Use the set ( router-lan) phy command to specify the Ethern et PHY (physical s pecifications) speed and mode. NOTE: It is highly recommended that thi s setti ng be le ft at auto- negoti ation.
Axxiu s 800 - R elease 2.2 5-14 5 CLI Comman ds set set (router-la n) rip Use the set (router-lan) rip commands to s pecify RIP for the specif ied LAN interface. set (rout er-lan) rip i p Use the set (router-lan) rip ip command to specify the IP RIP for the specified LAN interface.
5-14 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er-lan) rip i px Use the set (router- lan) rip i px command to specify the IPX RIP and SA P for the specified LAN interface.
Axxiu s 800 - R elease 2.2 5-14 7 CLI Comman ds set set (router-la n) stp Use the set ( router-lan) stp command s to configur e the Spanning Tree Pro tocol on this interface. set (router- lan) stp enable/d isable Use the set (router-la n) stp enable/d isable command to enab le/disable Spanning Tree Protocol on this interface.
5-14 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router- lan) stp port cost Use the set (router-lan) stp port cost command to co nfigure Spanning Tree path cost value for this bridge port.
Axxiu s 800 - R elease 2.2 5-14 9 CLI Comman ds set set (router-lan) up/down Use the set (router-lan) up/d own command to set the specified LAN interface up or down. When the Router port is set down, a link failure will not cause an alarm. This can be used to eliminate alarms from Router port s that are not in-use.
5-15 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-t runk ) encapsulation Use the set (router- trunk) encaps ulation command to specify the encapsula tion to use on the TSR interface.
Axxiu s 800 - R elease 2.2 5-15 1 CLI Comman ds set set (router-t runk) s peed Use the set (router-trunk) speed command to specify the data speed for each DS0 in the given trunk. This command takes effect upon transiti on of the trunk to active. This command app lies to the TSR card only.
5-15 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-wa n) dlci Use the set (router-wa n) dlci command to set the DLCI ( Data Link C onnection Iden tifier) for a specified WAN interface.
Axxiu s 800 - R elease 2.2 5-15 3 CLI Comman ds set set (router-wa n) gre Use the set (router-wan) gre comm and to config ure Generic R outing Encap sulatio n tunnel ing for a specified WAN inter face.
5-15 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er-wan) gre ip Use the set ( router-wan) gre ip comm and to confi gure the GR E tunneli ng of the IP protocol for a specified WAN interface.
Axxiu s 800 - R elease 2.2 5-15 5 CLI Comman ds set set (router-wa n) ip Use the set ( router-wan) ip command to set the IP traffic h andling on the W AN interface.
5-15 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-wa n) ipx Use the set ( router-wan) ipx comman d to set the IPX traffic handlin g on the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-15 7 CLI Comman ds set set (router-wa n) nat Use the set (router- wan) nat commands to configure Netwo rk Address Translation (NAT) on a specified WAN interface.
5-15 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er-wan) nat enable/ disable Use the s et (router-wan) nat com mand to enable and di sable Network Add ress Translation (NAT) on a specified WAN interface.
Axxiu s 800 - R elease 2.2 5-15 9 CLI Comman ds set set (router-wa n) other Use the set (ro uter-wan) other comma nd to set t he t raf fic ha ndlin g of pr ot oco ls ot her th an IP or IPX on the specified WAN interface.
5-16 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-wa n) ppp Use the set (router) ppp command to configur e the PPP ( Point-to-P oint Pr otocol) on the specified Router card .
Axxiu s 800 - R elease 2.2 5-16 1 CLI Comman ds set set (router- wan) ppp compression Use the set (router-wan) ppp co mpression command to con figure the PPP compr ession with the remote PPP d evice.
5-16 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (router-wa n) rip Use the set ( router-wan) rip command s to set the type of RIP updates on the WAN interface. set (router- wan) rip ip update s Use the set (router-wan) rip ip updat es command to set the type of RI P updates on the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-16 3 CLI Comman ds set set (router-wa n) stp Use the set (router-wan) stp commands to configure the Span ning Tree Protocol o n the specified WAN interface. set (rout er-wan) stp enable/ disable Use the set (router-wan) st p enable/disa ble command to enab le and disable Spann ing Tree Protocol on this interface.
5-16 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (rout er-wan) stp port cost Use the set ( router-wan) stp port cost command to configure Span ning Tree path co st value for this bridge port.
Axxiu s 800 - R elease 2.2 5-16 5 CLI Comman ds set set (router-wa n) trunk Use the set (router-wa n) trunk command to configure the trunk port or mult ilink group for a specified WAN interface. If the trunk encapsula tion is subsequently ch anged, this tru nk ass ignm ent is r ese t to 0.
5-16 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set s creen Use the set screen command to set t he height of the scr olling output screen , in number of lines. For example, if the screen height is set to 40 lines, the Command Line Interface (CLI) will print the maxi mum of 40 lines o f a long output before paus ing.
Axxiu s 800 - R elease 2.2 5-16 7 CLI Comman ds set set s nmp Use the set snmp command to set the Simple N etwork Management Protocol (SN MP) MIB-II System Group o bjects. Synt ax: set snmp {setting} {"string"} Where {setting } is as below, and {string} is its value.
5-16 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set time Use the set ti me command to set th e time. Synt ax: set time {hh:mm:ss} Exampl e: set time 12:00:00 The exampl e will set the time to 12 no on. {hh:mm:ss} Where hh:mm:ss is the time in ho urs, minutes, and seconds, usin g a 24-hour clock.
Axxiu s 800 - R elease 2.2 5-16 9 CLI Comman ds set set user Use the set user comm and to modify attributes for a s peci fic user that have been created with the add use r command . set u ser level Use the set user level com mand to set the user access level.
5-17 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (v35 ) Use the se t (v35) comman d to setup V.35 ports. The comm and specifies the range of channels within that card, and the setting to apply. Synt ax: set {v35-addr} {setting} Exampl e: set 6:1 rxclk normal To set port 1 (v.
Axxiu s 800 - R elease 2.2 5-17 1 CLI Comman ds set speed Set the data rate for each DS0 to which a V.35 is crosscon nected 56 56K d at a rat e 64 64K d at a rat e txclkinv Set the transmit clock inv .
5-17 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set (v54 ) Use the set ( v54) co mmand to se tup V.54 Loopback Test Parameters. The command specifies the range of channels within that card, and the sett ing to apply.
Axxiu s 800 - R elease 2.2 5-17 3 CLI Comman ds set [nnn] chart pattern Syntax: set{v54-addr} v54 equipm ent pattern {n} Set V.54 test patter n n is from the following: 0 = QRSS pattern (d efault) 1 =.
5-17 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds set set verification Use the set verification co mmand to enabl e or disa ble verifi cation prom pts. Synt ax: set verification {off|on} Exampl e: set verification off The exampl e will cause yes/no verification messages to be s uppressed.
Axxiu s 800 - R elease 2.2 5-17 5 CLI Comman ds show show The following s how commands are link ed to a detailed d escription of each command. show (adpcm) show (rout er) ntp show autoex it show (rout.
5-17 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (adpcm) Use the show (a dpcm) command to dis play the settings for the ADPCM card. Synt ax: show {adpcm-addr} Exampl e: > show 6:1 show 6:1 SLOT 6: Settings for DS1 1: Circuit ID: CAC DS1# 6:1 Up/Down: UP Framing: ESF Line Coding: B8ZS Line Build Out: DSX-1 EQUALIZATION FOR 0- 133 ft.
Axxiu s 800 - R elease 2.2 5-17 7 CLI Comman ds show show autoex it Use the show autoexit co mmand to display whether auto exit is on or off. If on, the time-out peri od is di spla yed. Synt ax: show autoexit Exampl e: > show autoexit Autoexit is off.
5-17 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show cclabels The show c cl ab els command displa ys all us er defined DS 0 cross- connect l abels.
Axxiu s 800 - R elease 2.2 5-17 9 CLI Comman ds show show connect The show connect com mand displays the static conn ections for channels and ports. Synt ax: show connect {slot|slot:port|slot:port:cha.
5-18 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show connect adpcm The show connect adpcm command dis plays the connections for the ADPCM port. Synt ax: show connect adpcm {adpcm-addr} Exampl e: .
Axxiu s 800 - R elease 2.2 5-18 1 CLI Comman ds show show (ds0) The sho w (ds0) command displays settings for DS0s. Synt ax: show {ds0-addr} Exampl e: show a:2:1-2 In the following example, the show (ds0) command has queried s lot A (Contr oller car d), port 2, ch annels 1 th rough 2.
5-18 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (ds1) The sho w (ds1) command displays settin gs for DS1s. Synt ax: show {ds1-addr} Exampl e: show 1:1 SLOT A: Settings for DS1 1: Circuit ID: CAC DS1# A:1 Up/Down: DOWN Framing: ESF Line Coding: B8ZS Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft.
Axxiu s 800 - R elease 2.2 5-18 3 CLI Comman ds show show (ds3) The sho w (ds3) comm and disp lays t he current se ttings fo r a DS3. Synt ax: show {ds3-addr} Exampl e: show a:1 SLOT A: Settings for D.
5-18 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show {ds3-addr} In the form of {slot:port}. show ethernet The show ethernet co mm and disp lays Et her ne t and IP se ttin gs. Exampl e: show ethernet > show ethernet IP Address and Mask : 198.162.3.196 255.
Axxiu s 800 - R elease 2.2 5-18 5 CLI Comman ds show show (fxo) The show (f xo) command d isplays the setti ngs for FXOs. Synt ax: show {fxo-addr} Exampl e: show 7:1 The example shows settings for port 1 on the FXO card i slot 7.
5-18 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (fxsPS or fxsPSM) The sho w (fxsPS or fxsPSM) co mmand displ ays the se ttings fo r the Si ngle Ch annel POTS card wi thout mod em (FXS PS) or wi th modem (FXS PSM). Synt ax: show {fxsPS-addr|fxsPSM-addr} Exampl e: show 8:1 The example shows sett ings for the FXS PS card in slot 8.
Axxiu s 800 - R elease 2.2 5-18 7 CLI Comman ds show show image The sho w imag e command displays the ap plication images stored in the Controller or Rout er. Synt ax: show [rtr_card-addr] image Exampl e: show image > show image App. Image: Ver=7.0 Fri Aug 29 06:40:42 2003 - ACTIV E App.
5-18 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show impedance The sh ow impe danc e com mand dis pla ys the imp edan ce setti ngs f or FX S 5G c ar d. Synt ax: show impedance Exampl e: show impedance Index Im pedance CODEC Country 1 120 Ohms + (.
Axxiu s 800 - R elease 2.2 5-18 9 CLI Comman ds show show ip The sho w ip command displays the IP Ad dress info rmation for the Axxius 800. Synt ax: show ip Exampl e: show ip IP Address and Mask : 192.168.3.193 255.255 .255.0 IP Address of the G ateway: 192.
5-19 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show lsprotect The show lsprotect command di splays the low speed protection inf ormation. Synt ax: show lsprotect Exampl e: show lsprotect > SH.
Axxiu s 800 - R elease 2.2 5-19 1 CLI Comman ds show show ntp The sho w ntp co mmand dis plays se ttings for Network Time Proto col. Synt ax: show ntp Exampl e: show ntp NTP Settings: NTP: Disab led NTP Server Address : 0.
5-19 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show radius The show ra dius com mand displays the RADIUS config uration settings for the Co ntroller.
Axxiu s 800 - R elease 2.2 5-19 3 CLI Comman ds show show (router) The show (router) command displays the settings for the Router card. Synt ax: show {rtr_card-addr} Exampl e: show 1 SLOT 1: LMI Setti.
5-19 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show Spanning Tree Protocol Settings for Router: Spanning Tree: Disabled Syslog Settings for Ro uter: Syslog: Disabled TFTP Upload/Download U ser Settin.
Axxiu s 800 - R elease 2.2 5-19 5 CLI Comman ds show show (router) dhcp The show (router) dhcp command displays the cur rent DHCP settings for the Router card. Synt ax: show {rtr_card-addr} dhcp Exampl e: show 5 dhcp The following 3 examples, shows there is different information is displayed depending on the settin gs.
5-19 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router) dns The show (router) dns command disp lays the current DNS setup f or the Router card . Synt ax: show {rtr_card-addr} dns Exampl e: show 3 dns > show 3 dns SLOT 3: DNS Settings: DNS Resolver: Disabled DNS Server 1 IP Ad dress: 0.
Axxiu s 800 - R elease 2.2 5-19 7 CLI Comman ds show show (router) lmi The show (router) lmi command displays the curren t Local Management I nterface (LMI) settings for the R outer card. Synt ax: show {rtr_card-addr} lmi Exampl e: show 5 lmi The example shows the LMI settings for the Router card in slot 5.
5-19 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router) ntp The show (router) ntp comm and d ispl ays se tti ngs f or NTP o pti ons. Synt ax: show {rtr_card-addr} ntp Exampl e: show 4 ntp The exampl e shows the NTP options fo r the Router card in slot 4.
Axxiu s 800 - R elease 2.2 5-19 9 CLI Comman ds show show (router) port The show (router) port comman d displays the current TSR por ts configurat ion.
5-20 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router) ppp The show (router) ppp command displa ys the current Local P PP (Point -to-Poin t Protocol ) authentication and security settin gs for the Router card.
Axxiu s 800 - R elease 2.2 5-20 1 CLI Comman ds show show (router) rip The show (router) rip command dis plays the curre nt RIP settings for the Router card.
5-20 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router) stp The sho w (router) stp command di splays t he curre nt Spanning T ree Protoc ol se ttings for the specified Router card .
Axxiu s 800 - R elease 2.2 5-20 3 CLI Comman ds show show (router) uploaduser The show uploa duser com mand displays the current list of users allowed to upload and download con figuration and co de files.
5-20 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router-lan) The show (router-lan) command di splays the settings for the router car d. Synt ax: show {rtr_lan-addr} Exampl e: show 3:1 > s.
Axxiu s 800 - R elease 2.2 5-20 5 CLI Comman ds show Total: 0 Static MAC Address Set tings for LocalUnit: Total: 0 LAN Filters Enabled fo r LocalUnit: Forward Mode: Forw ard ALL Frames NOT Matching Fi.
5-20 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router-lan) filte r The s how (router-lan) f ilter command disp lays the current LAN Layer 2 data filters appl ied to the LAN on the specified Router card.
Axxiu s 800 - R elease 2.2 5-20 7 CLI Comman ds show {rtr_lan -addr} The Router address is in the form {slot:p ort} or {slot "profile-name"} [addres s|cus tom|p rotoco l|all] This setting will disp lay the defined filter types of the specified fil ters.
5-20 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (rout er-la n) stat ic The show (rou ter-lan) static co mmands to display the current list of static entries for the LAN on the specified Router car d.
Axxiu s 800 - R elease 2.2 5-20 9 CLI Comman ds show show (router -lan) stati c ip network The show (router-lan) static ip network command displays the current list of static IP network entries for the LAN on the s pecified Router card.
5-21 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router -lan) stati c mac address The show (router-la n) static mac address command displays the current list of stati c MAC address entr ies for the LAN on the specified Rou ter card.
Axxiu s 800 - R elease 2.2 5-21 1 CLI Comman ds show show (router-lan) stp The show (r outer-lan) stp co mmand display s the current Spanning Tree Protocol settings for the specified LAN interf ace.
5-21 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router-wan) The sh ow (router-wan ) command dis plays the current conf igu ration settings for the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-21 3 CLI Comman ds show WAN Spanning Tree Prot ocol Settings for RemoteUnit: Spanning Tree: Disabled WAN Static IP Network Settings for RemoteUnit: Total: 0 WAN Static IPX.
5-21 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router-wan) firewa ll The show (router-wan) firewall command displays the current firewall filter settings for the specified WAN interface.
Axxiu s 800 - R elease 2.2 5-21 5 CLI Comman ds show show (router-wan) ppp The sho w (rou ter-w an) ppp com mand displ ays the cu rrent PPP (Point-to -Point P rotocol) settings for the specified WAN interface.
5-21 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router-wan) st atic ip addr ess The show (router-wan) static ip a ddress command displays the curr ent list of static IP address entries for the specified W AN interface.
Axxiu s 800 - R elease 2.2 5-21 7 CLI Comman ds show show (router-wan) st atic ip x netw or k The sho w (router-wa n) st atic ip x netwo rk command displays the current lis t of static IPX network entries for the specified WAN interface.
5-21 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (router-wan) st atic nat address The show (r oute r-wa n) st atic na t addre ss command displays the cur rent static NAT addres s entries for the specified W AN interface.
Axxiu s 800 - R elease 2.2 5-21 9 CLI Comman ds show show (router-wan) trunk The show ( rou ter-w an) tr unk command displays the current trun k assignm ent for the s pecified WAN interface.
5-22 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show snmp The sho w snmp command display s the SNMP settings. Exampl e: show snmp SNMP Settings: System Name: System Location: System Contact: GET .
Axxiu s 800 - R elease 2.2 5-22 1 CLI Comman ds show show time The sh ow ti me comman d display s the sy stem time, in 24 ho ur hh:mm: ss for mat. Synt ax: show time Exampl e: show time > show time.
5-22 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds show show (v35) Use the show (v35) to display cur rent set tings for V.3 5 card. Synt ax: show {v35-addr} Exampl e: show 2:1 The example shows settings for port 1 (V.
Axxiu s 800 - R elease 2.2 5-22 3 CLI Comman ds show show (v54) Use the show (v54) to display cur rent set tings for V.5 4 card. Synt ax: show {v54-addr} Exampl e: show 3:1 The example shows settings for port 1 (V.
5-22 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status Use the statu s command to s ee the status of the system clocks , DS0s, DS 1s, equipmen t, and th e DS0 Mana gement Channel .
Axxiu s 800 - R elease 2.2 5-22 5 CLI Comman ds stat us statu s (adpcm) Use the stat us (adpcm) co mmand to display the status info rmation for the ADPCM card .
5-22 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (adpcm) performance Use the status (a dpcm) performance command to display the performance statistics for the current (15 min) and previo us (15 mi n, hour an d day) inf ormation fo r the ADPCM card.
Axxiu s 800 - R elease 2.2 5-22 7 CLI Comman ds stat us status (adpcm) performance history Use the status (a dpcm) performance history comm and to display p erformance statistics for the current 15 minute interval and all previous 15 minute in tervals (up to a total of 96) for the ADPCM card.
5-22 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (bri) Use the statu s (bri) command to display th e status information fo r the ISDN BRI card. Synt ax: status {bri-addr} Exampl e: status 3:1 The e xam ple d isp lay s sta tus of por t 1 (B RI) on sl ot 3.
Axxiu s 800 - R elease 2.2 5-22 9 CLI Comman ds stat us status (bri) performance Use the status (bri) performance command to disp lay the perform ance statistics f or the cur rent (hour and day) and previous ( hour and day ) for the ISDN BRI card.
5-23 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (bri) pe rf ormance history Use the statu s (bri) performance histor y command to dis play the perfor mance statistics for the curr ent 1 hour interval and all previo us 1 h our inte rvals for t he ISDN BRI card.
Axxiu s 800 - R elease 2.2 5-23 1 CLI Comman ds stat us statu s (ds0) Use the statu s (ds0) command to display the current status of the specif ied DS0. Synt ax: status {ds0-addr} Exampl e: status a:1:1 Displa ys the curren t status of the DS 0s on por t 1 on s lot A (contro ller card), po rt 1, channel 1.
5-23 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (ds1) Use the sta tus (ds1 ) command to display the curren t status of a DS1. Synt ax: status {ds1-addr} [performance] [history] Exampl .
Axxiu s 800 - R elease 2.2 5-23 3 CLI Comman ds stat us status (ds1) performance Use the status (ds1) performance command to display the performance stat istics for the current (15 min) and previo us (15 min, hou r and day) i nforma tion of a DS 1.
5-23 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (ds1) performance history Use the status (ds1) perf ormance history command to d isplay performance s tatistics for the current 15 minute interval and all previou s 15 minute intervals (up to a total of 96) of a DS1.
Axxiu s 800 - R elease 2.2 5-23 5 CLI Comman ds stat us statu s (ds3) Use the sta tus (ds3 ) command to display the curren t status of the specified DS3.
5-23 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status (ds3) performance Use the status (ds3) performance command to display the performance stat istics for the current (15 min) and previo us (15 min, hou r and day) i nformatio n of a DS3.
Axxiu s 800 - R elease 2.2 5-23 7 CLI Comman ds stat us statu s (ds3) performance history Use the status (ds3) performance history command to d isplay performan ce statistics for the current 15 minute interval and all previou s 15 minute intervals (up to a total of 96) of a DS1.
5-23 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s eq uipment Use the status equipmen t command to display current equ i pment information of th e Axxius 800.
Axxiu s 800 - R elease 2.2 5-23 9 CLI Comman ds stat us Exampl e: status equipment 3 The example with display the status of th e card in s lot 4. In this example a TSR card is in this slot. > status equipment 3 SLOT 3 CardType: TS Rx4 Status: Pr esent SW Revision: 1.
5-24 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us sta tus ( fxsPS or fxsPS M) Use the statu s (fxsPS or FXS PSM) to d isplay the current near -end line status of the sp ecified FXS PS or FXS PS card wit h modem. Synt ax: status {fxsPS-addr|fxsPSM-addr} Exampl e: status 4:1 The ex am ple d ispla ys st atus of po rt 1 ( FXS PS) on slot 4 .
Axxiu s 800 - R elease 2.2 5-24 1 CLI Comman ds stat us statu s lsprot ect Use the st atus lspr ote ct comman d to display the curren t status of the low speed protection cards.
5-24 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (ocudp) Use the stat us (o cu dp) command to displaystatus for self test and loopbacks.
Axxiu s 800 - R elease 2.2 5-24 3 CLI Comman ds stat us statu s (ocudp) performance Use the stat us (o cudp) performance comman d to display perf ormance statistics for the curren t 15 minu te interv al, previ ous 15 minu te inte rval, prev ious 1 hour interv al, and for the previ ous day.
5-24 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status (ocudp) performance history Use the stat us (ocu dp) per form an ce hi story command to disp lay performance statistics f or the current 15 minute interval and all previou s 15 minute intervals (up to a total of 96).
Axxiu s 800 - R elease 2.2 5-24 5 CLI Comman ds stat us statu s (rout er) status (router) al arms Use the statu s (r outer ) al arm s command to d isplay the current alar m log from the specified TSR card. Synt ax: status {tsr_card-addr} alarms Exampl e: status 5 alarms ROUTER BLADE ALARM LOG REPORT Slot-5 Time Mess age Count Jan 4 22:26:47.
5-24 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status (router) events Use the status (router) events command to display the curren t event log from the specified Router card. Synt ax: status {rtr_card-addr} events Exampl e: status 5 events > status 5 events ROUTER BLADE EVENTS LOG REPORT Slot-5 Time Me ssage Count Jan 10 0:56:44.
Axxiu s 800 - R elease 2.2 5-24 7 CLI Comman ds stat us status (router) ip address table Use the stat us ( rou ter) ip ad dress tab le command to display the current IP address table for the specified TSR card.
5-24 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status (router) ip network table Use the status (router) ip networ k table command to d isplay the cu rrent table of learned IP Networks for the specified interface o n the Router card.
Axxiu s 800 - R elease 2.2 5-24 9 CLI Comman ds stat us status (router) ipx network table Use the status (r outer) i px netwo rk table command to display the current table of learned IPX Networks for the specified interface on the Router card.
5-25 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status (router) ipx server table Use the status (r outer) ipx server table command to display the cur rent table of learned IPX Servers for the specified interface on the Rout er card.
Axxiu s 800 - R elease 2.2 5-25 1 CLI Comman ds stat us status (router) mac address ta ble Use the status (router) mac address table command to display the current table of learned MAC Addresses f or the specified interface o n the Router card .
5-25 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us status (router) per formance Use the status (r outer) performance comman d to display the current runtime statis tics from the sp ecified Router card.
Axxiu s 800 - R elease 2.2 5-25 3 CLI Comman ds stat us statu s (rout er-lan ) Use the status (router-l an) comman d to display the cu rrent Router status information. Synt ax: status {rtr_lan-addr) Exampl e: status 3:1 The exampl e displays status of the Router card in slot 3.
5-25 4 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (rout er-trun k) Use the stat us (router-tru nk) command to display the current status information for the specified Trun k on the Router card .
Axxiu s 800 - R elease 2.2 5-25 5 CLI Comman ds stat us statu s ses sions Use the status se ssions comma nd to display the current st atus of all active CLI sessio ns. Synt ax: status sessions Exampl e: status sessions > status sessions Session User Login Port ------- ---- ---------- * TELNET1 paul 192.
5-25 6 Axxius 80 0 - Rel ease 2.2 CLI Comman ds stat us statu s (v54 ) Use the stat us (v 54) to di splay the current near-end line status of the V.5 4 card. Synt ax: status {v54-addr} Exampl e: status 3:all The exampl e displays status of all ports (V.
Axxiu s 800 - R elease 2.2 5-25 7 CLI Comman ds store store The st ore command is used t o upload a s oftware fi le from a d efined slot to a def ined locatio n on a PC, v ia TFTP. Currently uploads for general use are only permitted for the Controller and TSR card configuration files .
5-25 8 Axxius 80 0 - Rel ease 2.2 CLI Comman ds switch switc h switc h ac tivei mage Use the switch activeimage com mand to switch the active with the backup application images stored in a C ontroller or Router car d.
Axxiu s 800 - R elease 2.2 5-25 9 CLI Comman ds switch switch (ds3) Use the switch (d s3) command to switch to the standby DS3 por t. Note: for redundant Axxius s ystems only.
5-26 0 Axxius 80 0 - Rel ease 2.2 CLI Comman ds telnet telnet telnet (rout er) Use the telnet (router) co mmand to establish a Telnet session from the Axxius 800 CLI to the Router card menu-driv en user interface. Synt ax: telnet {rtr_lan-addr} Exampl e: telnet 3 The example will T elnet into a TSR in Slot 3.
Axxiu s 800 - R elease 2.2 5-26 1 CLI Comman ds trace route trace r oute tracert (router ) Use the tracert (router) command to invoke a Trace Route to a host device on a network of a particular TSR Router.
5-26 2 Axxius 80 0 - Rel ease 2.2 CLI Comman ds trace route {ip-addr |"domain-name"} [t ype] [src-i p] This optional parameter, only applies it [ type] is set to ICMP. This defines the source IP address in the ICMP echo request an d must be one of the router interface I P addresses.
C HAPTER DS1 Controller Card In this Chapter n Overview n Feature s n Technic al Sp eci fic atio ns n Co nfigurat ion n Bu ilt-In Ca rd Handles n LEDs.
6-2 Axxius 800 - Release 2 .2 DS1 Cont roller Card Overview Ove rvi ew The Quad po rt DS1 Contr oller ca rd drives t he Axxius 800 Access Int egrat ion Platform, deli vering a cost- effecti ve, compac.
Axxiu s 800 - R elease 2.2 6-3 DS1 Control ler Card Feat ur es Features l Rescues u p to 35% or more of network ban dwidth c ommonly wast ed at the cell site or when pr oviding fr actional T1 ser vice.
6-4 Axxius 800 - Release 2 .2 DS1 Cont roller Card Technical Specifica tions Tech nica l Sp ecifications Product Includes l Built- in non-blo cking 1/ 0 Digital Cross-co nnect S ystem for up to 36 T1 .
Axxiu s 800 - R elease 2.2 6-5 DS1 Control ler Card Technical Specificatio ns Management l Local - RS- 232 craft por t inte rface dri ves up to 50 ft .
6-6 Axxius 800 - Release 2 .2 DS1 Cont roller Card Technical Specifica tions Service Inte rfaces Supported l Dual V.35/.5 4 Servi ce card ( hardened) l FXO Voice Ser vice c ard l ISDN BRI Servi ce car.
Axxiu s 800 - R elease 2.2 6-7 DS1 Control ler Card Technical Specificatio ns Alarms l Three vi sible alarm outp uts, cr itic al, major a nd minor l Three aud ible a larm output s, crit ical, major an.
6-8 Axxius 800 - Release 2 .2 DS1 Cont roller Card Contr oller Active and Stan dby Controller Active and Standby The Axxi us 800 can f unction f ully with a sing le Control ler car d, however Cont roll er redundan cy is a vailable with tw o like Cont rollers (DS1 or DS3) i nstal led.
Axxiu s 800 - R elease 2.2 6-9 DS1 Control ler Card Config uration Configuration Options o n the Qua d DS1 Controll er ca rd are se t by th e Command Line Inte rface (CLI) . Note: t he facepl ate s tate DS1/ E1 Controll er, the E1 fea ture is not suppor ted on this rel ease.
6-10 Axxius 80 0 - Rele ase 2.2 DS1 Cont roller Card Built-In Card Handles Built-In Card Handle s The Cont roller card i s designe d with a handle bui lt in to the faceplat e to a ssist i n the remo val of th e ca rd f rom the cha ssis . Th is ha nd le sl ides ou t aw ay fr om the uni t, crea ting a han dle fo r a mo re effec tive grip.
C HAPTER DS3 Controller Card In this Chapter n Overview n Feature s n Technic al Sp eci fic atio ns n Co nfigurat ion n Bu ilt-In Ca rd Handles n LEDs.
7-2 Axxius 800 - Release 2 .2 DS3 Cont roller Card Overview Ove rvi ew The Dua l port DS3 Control ler car d drives the Axxi us 800 Access Int egrat ion Platform, deli vering a cost- effecti ve, compac.
Axxiu s 800 - R elease 2.2 7-3 DS3 Control ler Card Feat ur es Features l 2 DS3 por ts built into t he Contr oller del iver bandwidth t o the r esiden t cell si te fo r serv ice deli very ap plicati o.
7-4 Axxius 800 - Release 2 .2 DS3 Cont roller Card Technical Specifica tions Management l Local - RS-232 craft por t interf ace dri ves up to 50 ft. (15 .
Axxiu s 800 - R elease 2.2 7-5 DS3 Control ler Card Technical Specificatio ns Service Inte rfaces Supported l Dual V.35/.5 4 Servi ce card ( hardened) l FXO Voice Ser vice c ard l ISDN BRI Servi ce ca.
7-6 Axxius 800 - Release 2 .2 DS3 Cont roller Card Technical Specifica tions Testing and Diagnostics l Suppor ts mainte nance s ignals sp ecified i n ANSI T1.
Axxiu s 800 - R elease 2.2 7-7 DS3 Control ler Card Contro ller Active an d Stand by Controller Active and Standby The Axxius 800 can f unction f ully with a sing le Control ler car d, however Cont roll er redundan c y is avai lable with two li ke Cont rollers (DS1 or DS 3) instal led.
7-8 Axxius 800 - Release 2 .2 DS3 Cont roller Card Contr oller and DS3 Redundancy Con troll er a nd D S3 Re dund ancy Protection Modes The Axxi us 800 can b e provisi oned wit h one or two DS3 Contro .
Axxiu s 800 - R elease 2.2 7-9 DS3 Control ler Card Contr oller and DS3 Redu ndancy swit ching th e output path s so that t he tran smit path of th e DS3 line is connect ed to the stan dby Control ler. Servi ce interr uptions ( hits) wil l be ta ken on both t he DS3 and lo w- spee d connecti ons dur ing this type of swi tch.
7-10 Axxius 80 0 - Rele ase 2.2 DS3 Cont roller Card Contr oller and DS3 Redundancy Network Protection Mode The networ k mode of prote ction requi res a single Cont roll er with two indepen dent DS3 chann els. The cros s connec ts are set up identic ally for both DS3s.
Axxiu s 800 - R elease 2.2 7-11 DS3 Control ler Card Config uration Configuration Opti ons on t he DS3 Con tro ller car d are set by th e fo ll owin g C LI c omm and s. CLI Commands The fo llowing co mmands are used t o configur e the DS3 Controlle r card.
7-12 Axxius 80 0 - Rele ase 2.2 DS3 Cont roller Card Built-In Card Handles Built-In Card Handle s The Cont roller card i s designe d with a handle bui lt in to the faceplat e to a ssist i n the remo val of th e ca rd f rom the cha ssis . Th is ha nd le sl ides ou t aw ay fr om the uni t, crea ting a han dle fo r a mo re effec tive grip.
C HAPTER FXO Voice Card In this Chapter n Overview n Features n Technical Specifi cations n Card Co nfiguratio n - CLI Comma nds - DIP S witch Settings n LEDs n Channel Ass ociated Signaling (CAS) Con.
8-2 Axxius 800 - Release 2 .2 FXO Voice Card Overview Ove rvi ew The FXO Voi ce Serv ice card provide s high -density provis ioning of reli able Fo reign Exchan ge Office ( FXO) or Dir ect Inward Di aling (DID) tele phone servi ces. Eig ht FXO or Dial Pulse Termin ate (DPT) telep hone l ine chann els c an be depl oyed on each FXO Ser vic e ca rd.
Axxiu s 800 - R elease 2.2 8-3 FXO Voice Card Feat ur es Features l Deliv ers FX O or D ID tele phon e se rvic es f rom T 1 ac ces s ci rcu its l Suppor ts CLASS servi ces incl uding cal ler ID, cal l.
8-4 Axxius 800 - Release 2 .2 FXO Voice Card Technical Specifica tions FXO Signalin g Performance l DC Loop Rang e: > 1600 Ω l oop or gro und sta rt l Ringer Equ ivale ncy Number (REN): 0.
Axxiu s 800 - R elease 2.2 8-5 FXO Voice Card Card Co nfigur ation Card Configu ration The FXO voic e card can be c onfigured , to suppor t either FXO loop start or FXO ground start signal ing, with v arious t ransmit and recei ve at tenuatio n optio ns.
8-6 Axxius 800 - Release 2 .2 FXO Voice Card DIP Switc h Settings DIP Switch Settings The FXO ca rd DIP switc hes are no t func tional on the Axxi us 800 p latform.
Axxiu s 800 - R elease 2.2 8-7 FXO Voice Card Chann el Associa ted Signal ing (CAS) C onversi ons Channel As sociated Signa ling (CAS) Conversions Cross-c onnects are done a t a DS0 leve l. The f ollowing r ules need to be ke pt in mind while per forming cr oss-c onnects f or a FXO voi ce card.
8-8 Axxius 800 - Release 2 .2 FXO Voice Card Channel Associ ated Si gnaling ( CAS) Co nversion s.
C HAPTER ISDN BRI Card In this Chapter n Overview n Features n Technical Specifi cations n Card Co nfiguratio n - CLI Comma nds n LEDs n Connecto r Pinouts - Wire-Wrap Pinout 2 Wire Services.
9-2 Axxius 800 - Release 2 .2 ISDN BRI Card Overview Ove rvi ew The ISDN BRI Ser vice Cards enable se rvice pro viders and ente rprises t o deploy high- densi ty, stand ards- based, ISDN Bas ic Rate Interf ace (BRI ) servic es over one or mo re T1 or DSL access lines using TDM or ATM transport.
Axxiu s 800 - R elease 2.2 9-3 ISDN BRI Card Feat ur es Features l Enabl es carri ers to eco nomically bundl e ISDN with all other servi ces at 64 Kbp s or 128 Kbps over T1 a ccess li nes l Conf ig ur.
9-4 Axxius 800 - Release 2 .2 ISDN BRI Card Technical Specifica tions Management l Standar d ISDN SNMP MIB support ed Network Interface l 3 DS0 mode: Uses 3 cont iguous DS0 chann els per I SDN BRI channe l on T1 Network Standards l Telc ordia TR-N WT-000397 ( 1993) l Telc ordia TR-TSY- 000821 (1 991) l Telc ordia TR-TSY- 000829 (1 989) l ANSI T1.
Axxiu s 800 - R elease 2.2 9-5 ISDN BRI Card Technical Specificatio ns Power l Maximum power i nput: 6 W (8 port) l Soli d- stat e fu sele ss p rot ecti on Environment In a ddit ion to the sys tem s e nvi ron men t req ui rem ent s, th e fo llo win g a pplie s t o th e IS DN BRI card.
9-6 Axxius 800 - Release 2 .2 ISDN BRI Card Card Con figur ati on Card Conf iguration BRI card op tions are se t with th e Command Line Inte rface (CLI).
Axxiu s 800 - R elease 2.2 9-7 ISDN BRI Card LEDs LEDs There is an LED for each ISDN BRI o n a car d. The funct ion for ea ch LED is listed belo w: State Desc rip tio n Off Line U-interface is attempting sy nchronization, or BR I is out of service. Red Line alarm (LOS or self test failure) Yellow ES or SES has occu rred.
9-8 Axxius 800 - Release 2 .2 ISDN BRI Card Connect or Pinou ts Connec tor Pi nou ts Wire- Wrap Pinout 2 Wire Services The f ollowing pinout applies to t he wire-wrap pi nout for the s lot o f the IS DN BRI car d.
C HAPTER OCU- DP Card In th is C hapter n Overview n Features n Technical Specifi cations n Card Confi guration - CLI Co mma nds - Ba sic Set up n LEDs n Jump er Se ttin gs n Alarms n Line Ra tes/Line.
10-2 Axxius 80 0 - Releas e 2.2 OCU-DP Card Overview Ove rvi ew The Si ngle Port and Quad Port all- rate OCU-DP Ser vice Cards provi de electr ical and phys ical t ermin ati on o f th e 4 -wi re Di gi.
Axxiu s 800 - R elease 2.2 10-3 OCU-DP Card Overview Customer Premi se Application In th is model, the c arrier de ploys t he Axxius 8 00 in conjunct ion with DDS DSU/CSUs to provi de sta ndards-ba sed DDS ac cess for c ustomer da ta ter minal n eeds.
10-4 Axxius 80 0 - Releas e 2.2 OCU-DP Card Overview SS7 Bac khaul Applicat ion In t his appl icatio n, the carr ier uses the OCU to transfer sig naling a nd cal l in format ion between MSCs.
Axxiu s 800 - R elease 2.2 10-5 OCU-DP Card Feat ur es Features l Provides availabl e base band data r ates fr om 2.4 to 7 2 Kbps l Suppor ts primar y and s econdary c hannel service s, 64K cl ear c hannel se rvice , and 4-wi re S wit che d-5 6 se rvic e l Complies wi th AT&T Pub.
10-6 Axxius 80 0 - Releas e 2.2 OCU-DP Card Technical Specifica tions Network Interface l Each OCU po rt DS0 cros s-connect ed to T1 por t Loopbacks OCU, CSU and DSU: l Manual loopbacks a ctivate via .
Axxiu s 800 - R elease 2.2 10-7 OCU-DP Card Card Co nfigur ation Card Conf iguration OCU-DP card options are set with th e Command Line Interface (CLI ).
10-8 Axxius 80 0 - Releas e 2.2 OCU-DP Card Card Con figur ati on Basic Setup Command De sc rip tion set {ocudp-addr} baud {2400|4800|9600|19200|38400| 56000*|64000} Set the OCU-DP Baud rate. Where ocu dp-addr = {sl ot:port} o f the OCU-DP card to apply s ettings t o.
Axxiu s 800 - R elease 2.2 10-9 OCU-DP Card LEDs LEDs There are two LEDs for each channel on the OCU-DP card . The funct ion for ea ch LED is li sted bel ow: State Desc ription Yellow Flick ering ALL B oot Software in control. Green (walking d own) Red (walking up) ALL Appli cation So ftware in co ntrol (repeated 3.
10-1 0 Axxius 80 0 - Releas e 2.2 OCU-DP Card Jumper Sett ings Jumper Settings The P1 a nd P2 Jumpers are de faulted t o RJ-48S, whi ch are the set of pins nearest t he bott om of t he serv ice card. W ith the jumper in this position the signa ls are routed to t he RJ-48S connector (s) on the f ace of the card.
Axxiu s 800 - R elease 2.2 10-1 1 OCU-DP Card Alarms Alarms The OCU-DP c ards and s upporting Control ler Soft ware will support the foll owing ala rms : Alarm/ Event Severi ty Category De scriptio n .
10-1 2 Axxius 80 0 - Releas e 2.2 OCU-DP Card Line Rates/Line Len gths Line Rate s/Li ne Len gt hs All leng ths were measure d to meet a BER of 10 -7 with up to 45 dB of cabl e atte nuation at the Ny quist frequency for 56, 64 and 72 Kbps, and 40 dB all ot her rate s.
Axxiu s 800 - R elease 2.2 10-1 3 OCU-DP Card Conn ector Pinouts Connec tor Pi nou ts The OCU-DP is p art of th e networ k, it conn ect to customer e quipment. DDS RJ-48S The pinout for RJ -48S fe male is as follows: Note : Th e ab ove li st ed f uncti ons are rela tive to t his p ort .
10-1 4 Axxius 80 0 - Releas e 2.2 OCU-DP Card Connect or Pinou ts Wire- Wrap Pinout 4 Wire Services The f ollowing pi nout a pplies t o the wire-wrap pinout fo r the slot of the OCU-DP c ard.
C HAPTER Single Channel POTS Cards In this Chapter n Overvi ew n Features n Technical Speci ficati ons n Card Con figuration - CLI Commands n Connector Pin outs n LEDs n Basi c Co nfigu rat ion.
11-2 Axxius 80 0 - Releas e 2.2 Single Chann el POTS Cards Overview Ove rvi ew A Single Channel POTS card provi des wire less serv ice provide rs a st andar d FXS voice ci rcuit for communic ations, wi th the operatio ns suppo rt group under conditi ons where the ce ll sit e radios a re bei ng serv iced.
Axxiu s 800 - R elease 2.2 11-3 Single Ch annel POTS C ards Technical Specificatio ns Tech nica l Sp ecifications Controller Software Requir ed l Release 1.0 or hi gher is r equired f or the POTS Service cards FXS Transmission Performance l Retu rn L oss : ERL > 28 dB , SR L > 20 dB wi th re spe ct to 90 0 Ω + 2.
11-4 Axxius 80 0 - Releas e 2.2 Single Chann el POTS Cards Technical Specifica tions Physical l POTS conne ctions a re through front panel RJ- 11 l Dimensions : 3.5 i n. (H) x 0.75 in. (W) x 11.25 in. (D) 8.9 cm (H) x 1.9 cm (W) x 28. 6 cm (D) l Weight: Si ngle Ch annel POTS - 5.
Axxiu s 800 - R elease 2.2 11-5 Single Ch annel POTS C ards Built-In Ca rd Handles Built-In Card Handle s The Singl e Channel POTS cards a re design ed with a handle bu ilt i nto the f aceplat e to assi st in t he remov al of the c ard fr om the chassis.
11-6 Axxius 80 0 - Releas e 2.2 Single Chann el POTS Cards Connect or Pinou ts Connec tor Pi nou ts RJ-11 Connector There is one RJ- 11 (female ) connecto r on th e front of the POTS c ard and two RJ-11 conne ctors on t he POTS car d with mo dem.
Axxiu s 800 - R elease 2.2 11-7 Single Ch annel POTS C ards LEDs LEDs The POTs ch annel L ED (lef t) stat us is describe d in t he table b elow. The sec ond LE D (rig ht) is a s tatu s LE D f or the MOD EM .
11-8 Axxius 80 0 - Releas e 2.2 Single Chann el POTS Cards Basic Configur ation Basic Co nfiguration W ARNING! D O NOT IN STAL L TWO S ING LE C HANNEL POTS SERVICE CARDS WITH MODEM IN A A XXI US CHASSIS . I F YOU DO , THE SYST EM WILL HANG . T O RESOLVE , YOU MUST REMOVE BOTH CARDS AN D PLUG ONLY ONE BACK IN .
C HAPTER Power Supply In this Chapter n Overview n Features n Technical Speci ficati ons n Input Power n LEDs n Instal ling/Repla cing a Power Supply.
12-2 Axxius 80 0 - Releas e 2.2 Power Supply Overview Ove rvi ew The Axxius 800 Power Supply op tions oper ate fro m either 24 VDC or 48 VDC to supply 5V p ower to the Axxius p latform. A s ingle Power Supply is capa ble of poweri ng the ent ire Axxius 800 uni t.
Axxiu s 800 - R elease 2.2 12-3 Power Supply Technical Specificatio ns Tech nica l Sp ecifications Componen ts l 24 VDC Power Supply l 48 VDC NI48 Power Supply l 48 VDC I48 Power Supply l Cable connector Elect rical I nput Charac teristics Input powe r ful ly isola ted from ci rcuit and ch assis gro und 24 VD C l 24 (21 .
12-4 Axxius 80 0 - Releas e 2.2 Power Supply Technical Specifica tions Alarms l Communicates stat us to Contr oller whe n 24 or 48 VDC inp ut voltag e is low Interface Connectors l Rear P CB connector : Axxius 800 backpla ne Environment In ad dition t o the s ystems e nviron ment req uiremen ts, th e foll owing appli es to the Pow er Su pp lies .
Axxiu s 800 - R elease 2.2 12-5 Power Supply Input P ower Input Po wer The fo llowing gr aphic displays the bac k of th e Axxius cha ssis, with the I nput powe r for the Power Sup ply slot A a nd B noted.
12-6 Axxius 80 0 - Releas e 2.2 Power Supply LEDs LEDs Both powe r supply ca rds have identica l LEDs, as d escribed i n the tabl e be low. LED State Des cript ion DC Input Off D C input missing or f .
Axxiu s 800 - R elease 2.2 12-7 Power Supply Instal ling/Rep lacing a Power Sup ply Installin g/Replacing a Power Supply Install a Power Supply The Axxius has red undant Power Supply S ystem ca pabilit y. The unit wi ll r un on one power supply (an d not be redundant ) or ca n have 2 power suppl ies in stalled .
12-8 Axxius 80 0 - Releas e 2.2 Power Supply Insta llin g/Replacin g a Pow er Supp ly.
C HAPTER Quad DS1 ADPCM Card In this Chapter n Overview n Featur es n Technical Speci fications n Card Con figuration - CLI Commands - Cross-Connects - Basic Se tup n Jumper Sett ings n Co nnector Pi .
13-2 Axxius 80 0 - Releas e 2.2 Quad DS1 ADPCM C ard Overview Ove rvi ew The Quad DS1 ADPCM Service c ard is a component o f the Ax xius 800 Acce ss Integr ation Pla tform.
Axxiu s 800 - R elease 2.2 13-3 Quad DS1 ADPCM Card Feat ur es Features l 32 Kbps ADPCM voice co mpression l Suppor ts Clear Channel S ignaling and li ne formatt ing fo r 32 Kbps ADPCM voic e-band sig nals accordi ng to ANSI T1.30 2-1989 l Grooms the voice a nd data mix from sel ectab le channel contr ol optio ns l Suppor ts up to 14 .
13-4 Axxius 80 0 - Releas e 2.2 Quad DS1 ADPCM C ard Technical Specifica tions T1 Interface (continued) l Jitte r: meets AT&T Pub . TR-62411 l Soli d-state fuseless overvo ltage and overcurrent li.
Axxiu s 800 - R elease 2.2 13-5 Quad DS1 ADPCM Card Technical Specificatio ns Alarms l Support s tandard T1 .403 ala rms l LOS (Loss of Signal), Red, Yellow, Blu e l ESF Per formance Error Count Thres.
13-6 Axxius 80 0 - Releas e 2.2 Quad DS1 ADPCM C ard Card Con figur ati on Card Configuration All options on the th is Serv ice card are se t using t he Comman d Line Int erfac e (CLI) . CLI Comman ds The f ollowing c ommands are us ed to confi gure the Quad DS1 ADPCM car d.
Axxiu s 800 - R elease 2.2 13-7 Quad DS1 ADPCM Card Card Co nfigur ation l show (adpcm) Disp lay s curr ent s etti ngs for th e A DPC M card ( circ uit ID, u p.do wn, framing, l ine codi ng, line bui ld out, lo op code detec tion, loop bac k, fdl ty pe, ADPCM, ADPCM Map) l show connect a dpcm Displays the co nnections for t he ADPCM port.
13-8 Axxius 80 0 - Releas e 2.2 Quad DS1 ADPCM C ard Card Con figur ati on Basic Setup Before c onfigu ring the DS1 ADPCM card, th ere ar e some basi cs that ne ed to be consi dered: l All DS0 s to be.
Axxiu s 800 - R elease 2.2 13-9 Quad DS1 ADPCM Card Card Co nfigur ation Cross-Connects It is i mporta nt to note that all t imeslots are cross -connecte d in pa irs. Th e actual p airs that can be cro ss-con nected are dependa nt upon which of the 3 suppor ted mappi ngs are set usi ng the set (ds1 card ) adpcm map command.
13-1 0 Axxius 80 0 - Releas e 2.2 Quad DS1 ADPCM C ard Jumper Sett ings Jumper Settings The P2 a nd P3 Jumpers are de faulted t o RJ-48, which are t he set of pins n earest t he conne ctors.
Axxiu s 800 - R elease 2.2 13-1 1 Quad DS1 ADPCM Card Conn ector Pinouts Connec tor Pi nou ts RJ-48 Connector There are four RJ-48 (fe male) connec tors on the fr ont of t he Quad DS1 ADPCM Card.
13-1 2 Axxius 80 0 - Releas e 2.2 Quad DS1 ADPCM C ard LEDs LEDs Each c hannel on the Quad DS1 ADPCM card has two LEDs. Th e descr iption of the top LED is shown b elow, th e bottom LED is not used wi th thi s applic ation.
C HAPTER Quad T1 & Quad DS1/E1 Card In this Chapter n Overview n Features n Technical Speci fications n Card Confi guration - CLI Comma nds n Jumper Settings n Connect or Pinouts - RJ-48 Connector.
14-2 Axxius 80 0 - Releas e 2.2 Quad T1 & Quad DS1/ E1 Card Overview Ove rvi ew The H ard en ed Qu ad T 1 a nd DS 1/E1 Se rvic e ca rds ena ble wirel ess serv ice pro vid ers to cost -effect ivel y provisi on and ex pand netw ork bandwidt h and gr oom availa ble DS0s onto o ther T1 tri butarie s for opt imal T1 bandwi dth uti lizati on.
Axxiu s 800 - R elease 2.2 14-3 Quad T1 & Quad DS1/E1 Card Feat ur es Features l Inte grated T1 CSU fun ctionali ty wit h FCC regist ration f or dir ect conne ction to T1 lines l B8ZS or AMI encod.
14-4 Axxius 80 0 - Releas e 2.2 Quad T1 & Quad DS1/ E1 Card Technical Specifica tions Tech nica l Sp ecifications Controller Software Requir ed l Release 1.0 or hi gher is r equir ed for the Quad T1se rvice ca rd T1 Interface l 4 T1 ports ope rati ng at 1.
Axxiu s 800 - R elease 2.2 14-5 Quad T1 & Quad DS1/E1 Card Technical Specificatio ns Clocking l Loop-t imed from an y T1 l External from BITS cl ock in put (t1.
14-6 Axxius 80 0 - Releas e 2.2 Quad T1 & Quad DS1/ E1 Card Technical Specifica tions Envi ron ment In addition to t he sys tems e nvironme nt re quireme nts, th e foll owing a pplie s to the Quad T1 ( har den ed) card . Fo r add iti ona l i nfo rmati on s ee Inst allation Enviro nment on page 2-3 .
Axxiu s 800 - R elease 2.2 14-7 Quad T1 & Quad DS1/E1 Card Card Co nfigur ation Card Configu ration All op tio ns o n th e t his ca rd are set u sin g th e Com man d L ine Interf a ce (CL I) . CLI Commands The fo llowing co mmands a re used t o configur e the Qu ad T1 card.
14-8 Axxius 80 0 - Releas e 2.2 Quad T1 & Quad DS1/ E1 Card Jumper Sett ings Jumper Settings The P2 a nd P3 Jumpers are de faulted t o RJ-48, which are t he set of pins n earest t he conne ctors.
Axxiu s 800 - R elease 2.2 14-9 Quad T1 & Quad DS1/E1 Card Conn ector Pinouts Connec tor Pi nou ts RJ-48 Connector There ar e four RJ-48 (fema le) connec tors on t he front of the Quad T1 and DS1/E1 Cards.
14-1 0 Axxius 80 0 - Releas e 2.2 Quad T1 & Quad DS1/ E1 Card LEDs LEDs Each c hannel on t he card ha s two LEDs. T he descri ption o f the top LED is sho wn belo w, the botto m LED is not used wi th this a pplicati on.
C HAPTER Terminal Server Router Card In this Chapter n Overview n F eatures n Technic al Sp eci ficat io ns n Card Co nfigu ration - CLI Commands n Connector Pinou t n LEDs.
15-2 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Overview Ove rvi ew The Q ua d-P ort T erm ina l Ser ver Ro uter (TS R) card co mbin es th e pe rfo rm anc e an d expan d abilit y of a sel.
Axxiu s 800 - R elease 2.2 15-3 Terminal Server Router Card Feat ur es Features l Enab les rem ote ma nag emen t of cell si te re sour ce s l Suppl ies 4 sel ectable RS- 232 synchr onous or 10/100Base.
15-4 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Technical Specifica tions Tech nica l Sp ecifications Controller Software Requir ed l Release 1.0 or hi gher is r equir ed for the TSR serv ice card l Release 2.0 or hi gher to s upport a TSR Se rvice card with TBOS l TSR relea se 1.
Axxiu s 800 - R elease 2.2 15-5 Terminal Server Router Card Technical Specificatio ns RS-232 In terface l Up to 4 RS-23 2 DCE ports l Sele ctable as ynchron ous data r ates and d ata parame ters l 8-p.
15-6 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Technical Specifica tions Frame Relay l RFC 1490 encapsu lation l ANSI T1.617 Anne x D LMI l ITU Q.
Axxiu s 800 - R elease 2.2 15-7 Terminal Server Router Card Technical Specificatio ns Equipment Su pported for TBOS-to-SN MP Conversion l Proxim Lynx. sc Micro wave Radio Model s 31250, 31600, 31250, 3 1650 l Proxim Lynx.
15-8 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Card Con figur ati on Card Configu ration The Ter minal S erver Route r car d has the o ption o f configu ratio n thro ugh CLI or th e TSR Menu-d riven sof tware, wh ich is ac cessed throug h Telnet.
Axxiu s 800 - R elease 2.2 15-9 Terminal Server Router Card Card Co nfigur ation l add (router -lan) filter Add a n ad dre ss f ilt er to the tabl e of Laye r 2 fi lt er a ppl ied s pecif ie d LA N inter face . l add (router -lan) sec ondary ip addre ss Add a se condary I P addres s and subne t to t he LAN inter face.
15-1 0 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Card Con figur ati on l delete (r outer) st atic dns host Dele te a s ta tic DN S h os t rec ord .
Axxiu s 800 - R elease 2.2 15-1 1 Terminal Server Router Card Card Co nfigur ation l reset (rou ter) Reboot the Route r. All new confi gurat ion sinc e the last co nfigur ation wi ll be in- use. l set (router) default Reset th e router to i ts defau lt con figurat ion sett ings, an d will re boot.
15-1 2 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Card Con figur ati on l set (router) reboot Set a utomati c reboot after an upload o f code or configu rati on file. l set (router) rip Speci fy versi on of RIP packets t o transmit and re ceive .
Axxiu s 800 - R elease 2.2 15-1 3 Terminal Server Router Card Card Co nfigur ation l set (router- wan) dlci Conf igu re t he D L CI f or a sp ecif ied WA N int er fac e th at wi ll be us ing a f ram e relay e ncapsul ated trunk. l set (router- wan) gre Confi gure the Ge neric Rout ing Enca psulatio n tunneling f or a speci fied WAN i nte rface .
15-1 4 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Card Con figur ati on l show (router) d ns Displays the cu rrent DNS settin gs for the TSR card.
Axxiu s 800 - R elease 2.2 15-1 5 Terminal Server Router Card Card Co nfigur ation l show (router -lan) fi lter Disp lay s the cur ren t LAN La yer 2 da ta fi lter s ap plie d to the LAN on the router card. l show (router -lan) st atic Displays the cu rrent list of static entri es for t he LAN on th e router card.
15-1 6 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Card Con figur ati on l status (r outer-tr unk) Displays the cu rrent st ate of the DNS res olver a nd the ent ries in the DNS cache . l st o re Save a software file fr om a slot t o a define d locati on on a PC, via TFTP.
Axxiu s 800 - R elease 2.2 15-1 7 Terminal Server Router Card Connector Pinout Connec tor Pi nou t 10Base-T E thernet The pi nout for the RJ-48C (fe male) c onnectors on t he front of t he card are as fo llows: RS-232 If th e card is set t o use the RS-2 32 connector (wit h jumper s) use the a bove RS-23 2 pinout s.
15-1 8 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card Connect or Pinou t TSR Card Jumpers The j umpers on the TSR card selec t the use of the 10/100Base- T (RJ-4 5) or RS-232. There is one ju mper for each po rt on the card. Each j umper ca n be set t o 10/10 0Base-T or RS- 232, in dependent o f the o thers.
Axxiu s 800 - R elease 2.2 15-1 9 Terminal Server Router Card LEDs LEDs The TSR s ervice ca rd has 2 LEDs per port. At Power -up Normal Operation Port Set for E ther net Top LED in dicates 1 00M Link,.
15-2 0 Axxius 80 0 - Releas e 2.2 Terminal Server Rout er Card LEDs.
C HAPTER V.35/.54 Card In this Chapter n Overview n Feature s n Technic al Sp eci fic atio ns n Card Co nfigu ration - CLI Commands n Cables n Connector Pinou ts - V.
16-2 Axxius 80 0 - Releas e 2.2 V.35/.54 Card Overview Ove rvi ew The Har dened Dual V.3 5/.54 Ser vice car d enabl es wirele ss ser vice prov iders to provisi on conne ctivit y to hi gh-speed s erial synchrono us Data T erminal Equi pment (DTE) d evices commonl y depl oyed in the cell sites.
Axxiu s 800 - R elease 2.2 16-3 V.35/.54 Card Feat ur es Features l Each p ort provi des any n x 56 / 64 Kbps data rat e up to 1.536 Mbps o n each port l Full non-blocki ng cro ss-connec tion o f all ti meslots t o any T1 a ccess li ne l Up to 1 6 V.
16-4 Axxius 80 0 - Releas e 2.2 V.35/.54 Card Technical Specifica tions Testing and Diagnost ics (V.35/ 54 card) l Addressa ble V.54 l oop up a nd loop down ( 127-code) patte rn generat ion/ dete ctio.
Axxiu s 800 - R elease 2.2 16-5 V.35/.54 Card Card Co nfigur ation Card Configu ration The V.35/54 card ca n be confi gured, u sing the Comman d Line Inte rface ( CLI). CLI Commands The fo llowing co mmands a re used t o configur e the V.3 5 cards. For detai led info rmatio n on these commands , see Chap ter 5, CLI Commands .
16-6 Axxius 80 0 - Releas e 2.2 V.35/.54 Card Cables Cables Dependi ng on your applica tion, you will nee d to purchas e one or more of the availa ble Carrier Access Corporati on V.35 da ta cables : These cables ca n be pur chased at a lic ensed Carr ier Access distri butor.
Axxiu s 800 - R elease 2.2 16-7 V.35/.54 Card Conn ector Pinouts Connec tor Pi nou ts V.35 DCE (DB-26) The V.35 DCE da ta port con necti on is made at the sub-mini atur e DB-26 connect or on the Axxiu s 800 usi ng the 10- foot, 2 5-foot, or 50 foot Car rier Acc ess DTE V.
16-8 Axxius 80 0 - Releas e 2.2 V.35/.54 Card Connect or Pinou ts LEDs Each V.3 5 port has an LED, with def initio ns as shown i n the tabl e belo w. Sub-miniatur e DB-26 Signal Winche ster 34 -pi n (.
C HAPTER Low Speed Protection Card In this Chapter n Overview n Features n Technical Speci fications n Card Confi guration - CLI Commands - Basic Setup of a Protected System n LEDs.
17-2 Axxius 80 0 - Releas e 2.2 Low Speed Protection Card Overview Ove rvi ew Low spee d protec tion provi des back up circuit ry for any T1 servic e port on a Quad T1 serv ice card or Qua d DS1 ADPCM s ervice c ard i n the Axxi us chas sis.
Axxiu s 800 - R elease 2.2 17-3 Low Speed Protection Card Overview The Backup Card A Quad T1 or Quad DS1 ADPCM service card can be con figured as t he “Backup car d”. The Bac kup card pr ovides T1 po rt pr otection for other inst alled T1 s ervic e cards, and can oc cupy any one of the eight se rvice card slot s.
17-4 Axxius 80 0 - Releas e 2.2 Low Speed Protection Card Featur es Features l Redunda nt 1:7 T1 interf ace prote ction l Mainta ins se rvice durin g card swaps l Four T1 ports pro vide ho t-standb y .
Axxiu s 800 - R elease 2.2 17-5 Low Speed Protection Card Technical Specificatio ns Service Cards Supported l Quad T1 Se rvice Car d (hardene d) l DS1/E1 Serv ice Car d (hardene d) l Quad DS1 ADPCM Servi ce Card (ha rdened) Management l RS-232/V.
17-6 Axxius 80 0 - Releas e 2.2 Low Speed Protection Card Card Con figur ati on Card Conf iguration CLI Commands The fo llowing co mmands a re used t o configur e the Lo w Speed Prote ction car ds. For deta iled inf ormation on these commands, see Ch apter 5 , CLI Commands.
Axxiu s 800 - R elease 2.2 17-7 Low Speed Protection Card Card Co nfigur ation Use t he fo llo win g s tep s to s et u p a Prot ecte d S yst em. 1. Instal l a Rel ay card in the Axxi us Relay s lot.
17-8 Axxius 80 0 - Releas e 2.2 Low Speed Protection Card LEDs LEDs The Low S peed Pro tection card has 10 LEDs, which are defi ned bel ow. Each channel on t he Quad T 1 card h as two LEDs. The descri ption of the to p LED is shown bel ow, the bott om LED is not us ed wit h this applicat ion.
C HAPTER Maintenance In this Chapter n Software Loading - Loading System Software via TFTP - Upgrading Software Levels via XModem n Back up Axx ius 80 0 Co nfig urati on - Save Controller Configuratio.
18-2 Axxius 80 0 - Releas e 2.2 Maintenance Software Loadin g Software Loading Loading System Softw are via TFTP 1. Login to t he Axxi us 800, usin g a term inal emula tion progr am or via Te lnet. NOTE: The tftp utilit y prov ided by Carrier Access with the do wnloadable soft ware must be running, in the same directory as th e s oftw ar e f ile.
Axxiu s 800 - R elease 2.2 18-3 Maintenance Softw are Loadi ng Loading Router Software via TFTP 1. Login to t he Axxi us 800, usin g a ter minal emu lation pr ogram or vi a Telnet.
18-4 Axxius 80 0 - Releas e 2.2 Maintenance Software Loadin g load standby tftp {ip-addr} "file-name" CLI command to load software to the Standby Controller. See the l oad tf tp command f or detai ls. reset standby Do you really want to do this ? Y Reset the Standby Contro ller.
Axxiu s 800 - R elease 2.2 18-5 Maintenance Softw are Loadi ng Upgrading System an d Router Softw are via TFTP using Proxy Requir ed: - Rou ter Se rvice car d (TSR) r elease 1 .0 or hi gher - Contro ller sof tware 1.1 o r higher - Ether net cable connected to por t on front of Router card 1.
18-6 Axxius 80 0 - Releas e 2.2 Maintenance Software Loadin g 3. Afte r download, the progra m will be loade d from RAM into the flash memory and th e sy ste m w ill a uto mati call y re star t. W ai t until the boo t m enu pro mpt is disp layed befo re power ing down t he unit.
Axxiu s 800 - R elease 2.2 18-7 Maintenance Softw are Loadi ng Upgrading Software Levels via XModem The fo llowing upg rade c an also be performed t hrough the POTS modem. 1. Login to t he Axxi us 800. 2. En ter: load {ctrlr-id} xmodem to dow nl oad the app lica tio n fro m th e bin ary file .
18-8 Axxius 80 0 - Releas e 2.2 Maintenance Software Loadin g 3. The binar y fil e name is usua lly i n the format : Axxius Axxius.pkt. A t 9600 bau d, the f ile tr ansfer wil l ta ke approxi mately 2 0 minute s. 4. Afte r download, the progra m will be loade d from RAM into the flash memory and th e sy ste m w ill a uto mati call y re star t.
Axxiu s 800 - R elease 2.2 18-9 Maintenance Backup Axxi us 800 C onfigura tion Backup Axxius 800 Configuration A text file fro m the curr ent co nfigur ation can be gen erated to reloa d the in t he even t the conf iguratio n has been lost due to card or softwa re problems.
18-1 0 Axxius 80 0 - Releas e 2.2 Maintenance Backup Axxius 800 Co nfigu ration Load Controller Config uration 1. Open HyperTe rm sess ion with th e Axxius 800 unit. 2. In HyperTe rm, select Fi le/Pr ope rti es/S ett ings /AS CII S etu p . 3. Set t he Line delay t o 300 ms an d the Char acter del ay to 5 ms .
Axxiu s 800 - R elease 2.2 18-1 1 Maintenance Hot Swap Serv ice Ca rd Hot Swap Service Card To Hot- Swap (repl ace) a ser vice card while the uni t is power ed on, f ollow the steps belo w: 1. Gentl y slide t he Serv ice card straight out of the s lot.
18-1 2 Axxius 80 0 - Releas e 2.2 Maintenance Hot Swap Ser vice Card.
A PPENDIX Regulatory Approvals In this App endix This appendix co ntains a chart o f all th e componen ts of the Axxius 8 00 and their Re gulat ory Approval s.
A-2 Axxius 800 - Release 2 .2 Regulatory Approvals Ax x i us 8 00 Cha s s i s UL60950 FCC Part 15, Class A FCC Part 68 NEBS Level 3 cert, type 2 & 4 equip CSA C22.
A PPENDIX SNMP Interface In this App endix n Overview n SNMP B asi cs n Enterprise M IB Suppo rt n Router E nterprise MIB Support n Public MI B Support n Router Pu blic MIB Support n SNMP Trap Reports.
B-2 Axxius 800 - Release 2 .2 SNMP Interface Overview Ove rvi ew The Si mple Netwo rk Management P rotocol ( SNMP) enabl es network operat ions cen ters (NO Cs) to m oni tor an d ma nag e ne tw ork eleme nts acro ss a n in tern etw ork .
Axxiu s 800 - R elease 2.2 B-3 SNMP Interface Enter prise MI B Support Enterprise MIB Supp ort This rele ase is w ith f ull S NM Pv1 and S NMP v2c sup por t. En terp ris e MIB s ar e de fine d usin g only SMIv2 ( as note d in th e table) . Enterpris e MIB Name Enterpr ise MIB Filena me Axxius-SYSTEM-MIB Axxi us-sys tem.
B-4 Axxius 800 - Release 2 .2 SNMP Interface Router Enterprise MIB Supp ort Rout er Ente rpri se MIB Suppor t Enterpri se MIB Name Enterpr ise MIB Filena me Router Specif ic CAGENROUTER-CARDPROFILE-MIB caGenRout er-CardPr ofile.mib CAGENROUTER-FILTERS-MIB ca GenRouter-Fi lters.
Axxiu s 800 - R elease 2.2 B-5 SNMP Interface Public MI B Support Public MIB Suppo rt MIB Table Co mmen ts RFC1155 (RFC-11 55-smi.MIB) RFC1212 (RFC-12 12.MIB) RFC121 3 (RFC-1 213-MIB ) system interfaces ip icmp tcp udp snmp egp not s upported RFC1215 (RFC-12 15.
B-6 Axxius 800 - Release 2 .2 SNMP Interface Publi c MIB Supp ort MIB Table Co mmen ts RFC249 4 (DS0 -MIB, DS0BUNDLE-MIB) dsx0Con figTab le dsx0Chan MappingTabl e dsx0Bun dleTabl e Dsx0Bo ndingTable n.
Axxiu s 800 - R elease 2.2 B-7 SNMP Interface Rout er Publ ic MIB Su pport Router Publ ic MIB Support MIB Table Comment s RFC1213 (RFC- 1213-MIB) system in terf ace s ip icmp tcp udp snmp egp not supporte d RFC1907 (SNMPv2 -MIB) system snmp SMIv2 Ext ension of RFC1213 Sys ORTable not suppor ted RFC2011 (IP-MI B) ip icmp SMIv2 Ext ension of RFC1213.
B-8 Axxius 800 - Release 2 .2 SNMP Interface SNMP Tr ap R epo rts SNMP Trap Re ports The Axxi us 800 can s end the followin g SNMP trap r eports. Standard Tr aps Enterprise Trap s Trap Descr iptio n Tes t Me thod authentication Failure Occurs when a bad community string is used.
A PPENDIX Loopback Tests In this App endix n Overview n DS1 Loopb acks n V.35 Loo pbacks n V.35/V. 54 Loop.
C-2 Axxius 800 - Release 2 .2 Loopback Tests Alarms Alarms Test Alarm The Axxi us 800 alarm f unctions c an be manuall y teste d using the following c ommand for setting critica l, major an d minor a larms. Turni ng alarms on or off wi ll pr oduce alarm mes sages and log entr ies stat ing the alarm event was manual ly set/ cleared by the user .
Axxiu s 800 - R elease 2.2 C-3 Loopback Tests Alarms The following are hyperlinks to all the card LED information: DS1 Controll er Card, LEDs DS3 Controll er Card, LEDs FXO Voice Card, LEDs ISDN BRI C.
C-4 Axxius 800 - Release 2 .2 Loopback Tests Alarms Displa y Alarms Use t he alarms command to dis play the a ctive al arms. Eac h alarm is rela ted to a part icular a ddres s and has a s everi ty categ ory (maj or, minor , criti cal, a lert). The repo rt can be f iltere d by port a ddress and/or se verity.
Axxiu s 800 - R elease 2.2 C-5 Loopback Tests Logs Logs Display t he eve nt log to view a log of al l system e vents, or narrow t he vie w to only disp lay spe cific i nformat ion.
C-6 Axxius 800 - Release 2 .2 Loopback Tests Status and Perf ormance Status and Performance The f ollowing s tatus commands will display vital inform ation re gardin g the s ystem that will ai d in t roubleshoo ting. All commands li sted bel ow are h yperlinke d to the CLI comm an d .
Axxiu s 800 - R elease 2.2 C-7 Loopback Tests Overview Ove rvi ew A loopb ack te st is a d iagnos tic proc edure i n which a signal is tr ansmit ted an d retu rned to t he sendi ng devi ce af ter pass ing t hrough all o r a port ion of a ne twork or c ircui t.
C-8 Axxius 800 - Release 2 .2 Loopback Tests DS1 Loop backs View Status of Loopback > status a:1 SLOT A: Status for DS1 1: Receive: Traffic Transmit: Traffic Loopback: LINE Disable Line Loopback &g.
Axxiu s 800 - R elease 2.2 C-9 Loopback Tests DS1 Loop backs DS1 Payload Loop Loops a t DS1 (in f ramer) and refr ames the T1. Ha ve DS1 vend or chec k for fra ming/ erro rs.
C-10 Axxius 800 - Release 2 .2 Loopback Tests DS1 Loop backs Receiving DS-1 CSU Loop Causes a line Lo opback. Lo opup cod e sent by r emote unit or netw ork. Occ urs at lo cal DS1 CSU. Have DS1 vendor check for framing/e rrors. Enable Detection of CSU Loopcode Enable det ection of CSU loop code (10000 fo r loopup ; 100 fo r loopdo wn).
Axxiu s 800 - R elease 2.2 C-11 Loopback Tests DS1 Loop backs View Status of Loopback > show a:1 SLOT A: Settings for DS1 1: Circuit ID: CAC DS1# A:1 Up/Down: UP Framing: ESF Line Coding: B8ZS Line Build Out: DSX-1 EQUALIZATION FOR 0-1 33 ft.
C-12 Axxius 800 - Release 2 .2 Loopback Tests DS1 Loop backs DS1 Equipment Loo p Note: Quad T1 LED flashe s green during equ ipment loop . Enable Eq uipment Loopback Where a Quad T1 card is in slot 5.
Axxiu s 800 - R elease 2.2 C-13 Loopback Tests DS1 Loop backs errored seconds: 0 0 sev. errored frame seconds: 0 0 line errored secon ds: 0 0 controlled slip se conds: 0 0 bursty errored sec onds: 0 0.
C-14 Axxius 800 - Release 2 .2 Loopback Tests V.35 Loop back s V.35 Loop backs V.35 Line Loop Note: V.35 L ED flash es gre en during l ine loop. Loop oc curs at V.35 port. Check for sy nc and err ors at lo cal da ta port. Enable Line Loopback Where a V.
Axxiu s 800 - R elease 2.2 C-15 Loopback Tests V.35 Loop backs Disable Line Loopback > set 6:1 line loopdow n OK View Status of Loopback > show 6:1 SLOT 6: Settings for V35 Port 1: CTS: Always H.
C-16 Axxius 800 - Release 2 .2 Loopback Tests V.35 Loop back s V.35 Equipment Loo p Note: V.35 L ED flash es yel low during e quipment lo op. Loops at local V. 35 port. Check f or sync an d errors at remote data po rt, with or withou t BERT. Enable Eq uipment Loopback Where a V.
Axxiu s 800 - R elease 2.2 C-17 Loopback Tests V.35 Loop backs Disable Equipment Loopba ck > set 6:1 equipment lo opdown OK View Status of Loopback > show 6:1 SLOT 6: Settings for V35 Port 1: CT.
C-18 Axxius 800 - Release 2 .2 Loopback Tests V.35/V.5 4 Loop V.35/V.54 Loop V.35/V. 54 Ser vice Card Desc ription The V.35 Ca rd with V. 54 Loop Test pr ovides the cap ability for th e V.35 card to detect networ k loop bac k ini tiation signa ls and pro vide a networ k loop back for l oop te sting .
Axxiu s 800 - R elease 2.2 C-19 Loopback Tests V.35/V.5 4 Loop V.54 Loop Note : Lo cal LED f la she s yell ow , re mote LE D fla shes gr een. Enabl e V.
C-20 Axxius 800 - Release 2 .2 Loopback Tests V.35/V.5 4 Loop V.54 Equipment Loo pback Enable V.54 Equipment Loopup Where a V.35/V.5 4 card is in slot 6.
Axxiu s 800 - R elease 2.2 C-21 Loopback Tests V.35/V.5 4 Loop > status 6:1 SLOT 6: Status for V35 PORT 1 : DCD: High CTS: High DSR: High RTS: High DTR: High BERT: RUNNING BITS: 838695 0 ERRS: 0 BER: 0.
C-22 Axxius 800 - Release 2 .2 Loopback Tests V.35/V.5 4 Loop.
G LOSSARY 10Base-T The most widely installed Ethernet lo cal area networks (LANs ) use ordinar y telepho ne twisted-p air wire. When used on Eth ernet, this carri er medium i s known at 10BASE- T. 10BASE-T s uppor ts Ethernet’s 10 Mbps transmission speed.
Gloss ary - 2 Axxius 80 0 - Rele ase 2.2 Glossary authoriza tion authorization The process o f granting or denying acces s to a network r esource. Mos t computer secu rity systems are ba sed on a two-step process, sometimes more.
Axxiu s 800 - R elease 2.2 G lossary - 3 Glossary bipol ar bip olar The pr edominant signalin g method used for digital tran smissio n services, such as DDS and T1.
Gloss ary - 4 Axxius 80 0 - Rele ase 2.2 Glossary bro adband bro adba nd A technology that provides an extrem ely wide and fast ban dwidth s o that many peopl e can simult aneously use the serv ice.
Axxiu s 800 - R elease 2.2 G lossary - 5 Glossary channel channel A ge neric term for a commun ications path o n a given medium; multip lexing techn iques allow provi ders to put mul tiple channels over a single m edium.
Gloss ary - 6 Axxius 80 0 - Rele ase 2.2 Glossary Constan t Bit Rate (CBR) Const ant Bi t Rate (CBR) Refers t o the trans mission pro perties t hat data, video and voice uph old when traversing a transport medium. I nformation traveling at a cons tant bit rate means there is no fluctu ation in signal integrity .
Axxiu s 800 - R elease 2.2 G lossary - 7 Glossary DHCP DHCP Dynami c Host C onfigur ation Protocol. DHCP i s a net work confi guration that allows maint enance to be perform ed from a centr al site rather than by en d use rs.
Gloss ary - 8 Axxius 80 0 - Rele ase 2.2 Glossary E&M Sign al ing E&M Signali ng A signaling arrangement that uses se parate leads, called respectively the E lead and the M lead , for the sign aling and voice sig nals.
Axxiu s 800 - R elease 2.2 G lossary - 9 Glossary frame frame A fragment of data th at is packaged into a f rame format, which co mprises a header, paylo ad, and trailer. frame re lay A packet-switching protocol fo r connecting devices on a Wide Area Network (WAN).
Gloss ary - 1 0 Axxius 800 - Release 2 .2 Glossary GUI GUI Graphical User Inter face, pronounced "GOOEY". A set of screen presentations and metaph ors that utilize graphic elements such as icons in an attempt to make an operating system easier to use.
Axxiu s 800 - R elease 2.2 Gloss ary - 1 1 Glossary ISDN BRI ISDN BRI Integrated Ser v ices Digi tal Networ k. BRI, whi ch is 144,0 00 bit s per second and designe d for the d eskt op.
Gloss ary - 1 2 Axxius 800 - Release 2 .2 Glossary Line C oding Vio lation ( LCV) Line Coding Violation (LCV) This parameter is a count of both B PVs and EXZs occurring over the accumulation period . An EXZ increments the LCV by one reg ardless of the length of the zero s tring.
Axxiu s 800 - R elease 2.2 Gloss ary - 1 3 Glossary LULT LULT Lin e Unit Line Termination LUNT Line Unit Netw ork Termination Management Information Base (MIB) A data base of objects, with attributes and values, repr esenting the manageab le components of a networ k device.
Gloss ary - 1 4 Axxius 800 - Release 2 .2 Glossary Networ k Address Translat ion (NAT) Network Address Translation (NAT) An Internet standard that enables a local-area network (LAN) to use one set of IP addr esses for internal traffic and a s econd set of addresses for external traffic.
Axxiu s 800 - R elease 2.2 Gloss ary - 1 5 Glossary Password Authentication Protocol (PAP) Password Aut hen tica tio n Protocol (PAP) An authen tication pro tocol that allows Point- to-Point Pro tocol p eers to authenticate one ano ther. Peak Cell Rate (PCR) The Peak Cell Rate, in c ells/sec, is the cell rate which the sourc e may never exceed.
Gloss ary - 1 6 Axxius 800 - Release 2 .2 Glossary robb ed bi t robb ed bit A type of analog signaling that will o ccasionally steal information bits use d fo r cir cui t sig nal ing c odi ng . router A computer or internet working dev ice that directs traffic and moves packets between n etworks.
Axxiu s 800 - R elease 2.2 Gloss ary - 1 7 Glossary star net wo rk star network A star is a network topology that connects all devices to a central location called a hub. Trad itional star networks are designed to be easily expandable because hubs can be connected to additional hubs of other networks .
Gloss ary - 1 8 Axxius 800 - Release 2 .2 Glossary TBOS TBO S Telemetry Byte Oriented Se rial. TBOS is an alar m monitoring an d control prototy pe for tele phone netw ork equi pment. telnet An Intern et standard protocol that enables a computer to fu nction as a terminal work ing from a remo te computer.
Axxiu s 800 - R elease 2.2 Gloss ary - 1 9 Glossary V.90 V.90 The standa rd for full-duplex mo dems sending and receiving data across phon e lines at up to 56 ,600 bps, approved by the I nternati onal Telecommun ication Unio n (ITU) i n February , 1998.
Gloss ary - 2 0 Axxius 800 - Release 2 .2 Glossary.
I NDEX Numerics 10/1 00B ase -T Et her ne t Conn ec tor . . . . . . . . 1-13 10B ase- T . . . . . . . . . . . . . . . . . . . . . . Glossary-1 26-pi n mic ro-SC SI V.35 card . . . . . . . . . . . . . . . . . . . . . . . . . 16-7 V.35 /V. 54 c ard s . .
Index - 2 Axxius 80 0 - Rel ease 2.2 Index C Base Platfo rm . . . . . . . . . . . . . . . . . . . . . . . . 1-1 ACO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17 Card Remo val Handles 1- 10 , 6-10 , 7-12 , 11-5 Chass is . . . . . . . . .
Axxiu s 800 - R elease 2.2 Index - 3 Index C st at ic ip x net wor k . . . . . . . . . . . . . . 5-30 static mac address . . . . . . . . . . . . . . 5-31 static nat address . . . . . . . . . . . . . . . 5-32 use r . . . . . . . . . . . . . . . . . . .
Index - 4 Axxius 80 0 - Rel ease 2.2 Index C (fx o) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87 (fx sP S) . . . . . . . . . . . . . . . . . . . . . . . . 5- 88 (oc udp ) baud . . . . . . . . . . . . . . . . . . . . . . . . 5-97 loopb ack .
Axxiu s 800 - R elease 2.2 Index - 5 Index C enable/disable . . . . . . . . . . . . . . 5-136 syslog . . . . . . . . . . . . . . . . . . . . . . 5-13 7 enable/disable . . . . . . . . . . . . . . 5-137 facility . . . . . . . . . . . . . . . . . . . . 5-13 7 level .
Index - 6 Axxius 80 0 - Rel ease 2.2 Index C level . . . . . . . . . . . . . . . . . . . . . . . 5-169 pas swo rd . . . . . . . . . . . . . . . . . . . . 5-169 verificat ion . . . . . . . . . . . . . . . . . . . . 5-174 show . . . . . . . . . . . . . .
Axxiu s 800 - R elease 2.2 Index - 7 Index D perfor mance command . . . . . . . . . 5-23 3 perfor mance history . . . . . . . . . . . 5-234 (ds3 ) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-235 perfor mance . . . . . . . . . . . . . . . . .
Index - 8 Axxius 80 0 - Rel ease 2.2 Index D (ro ut er) dhcp server option command . . . . . . . 5-44 dns pro xy comman d . . . . . . . . . . . . . . 5-44 remote command . . . . . . . . . . . . . . . . 5-45 snmp com munity comman d . . . . . . . . 5-45 snmp t rap command .
Axxiu s 800 - R elease 2.2 Index - 9 Index E features . . . . . . . . . . . . . . . . . . . . . . 16-3 , 17-4 LEDs . . . . . . . . . . . . . . . . . . . . . . . 16-8 , 17-8 over vi ew . . . . . . . . . . . . . . . . . . . . 16-2 , 17-2 E Electro nics Protect ion Mode .
Index - 10 Axxius 800 - Release 2 .2 Index L L label DS0 connec t ion . . . . . . . . . . . . . . . . . . . . 5-74 FXSPS conn ection . . . . . . . . . . . . . . . . . 5-74 Router trunk con nection . . . . . . . . . . . . . 5-74 V.35 connection . . . .
Axxius 800 - Re lease 2.2 Index - 11 Index Q command . . . . . . . . . . . . . . . . . . . . . . . . . 5-63 pino ut s . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11 10Base-T Et hernet . . . . . . . . . . . . . . . . . 15-1 7 10B ase- T e the rn et .
Index - 12 Axxius 800 - Release 2 .2 Index S connecto r pinout . . . . . . . . . . . . . . . . . . . 1-12 dat a port . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 rtrp in g co mma nd . . . . . . . . . . . . . . . . . . . . . 5-68 S security enhanced .
Axxius 800 - Re lease 2.2 Index - 13 Index S password command . . . . . . . . . . . . 5-120 pro mpt c om mand . . . . . . . . . . . . . 5-12 1 protoco lport comman d . . . . . . . . . 5-121 stopb its command . . . . . . . . . . . . . 5 -122 tbos map des cri pti on com ma nd .
Index - 14 Axxius 800 - Release 2 .2 Index S enable/disable com mand . . . . . . . 5-163 port cost co mmand . . . . . . . . . . . . 5-164 por t pri or ity comm and . . . . . . . . . 5-164 trunk comman d . . . . . . . . . . . . . . . . . 5-165 up/d ow n co mman d .
Axxius 800 - Re lease 2.2 Index - 15 Index S ppp comman d . . . . . . . . . . . . . . . . . . 5 -215 static ip address command . . . . . . . . . . . 5-216 ip network command . . . . . . . . . . . 5-216 ipx netw ork command . . . . . . . . . . 5-21 7 mac address command .
Index - 16 Axxius 800 - Release 2 .2 Index T stp co mmand . . . . . . . . . . . . . . . . . . . 5-252 (ro ut er- lan ) . . . . . . . . . . . . . . . . . . . . . . 5-253 (rou ter-trun k) command . . . . . . . . . . . . 5-254 (v54 ) command . . . . . . .
An important point after buying a device Carrier Access Network Device Axxius 800 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Carrier Access Network Device Axxius 800 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Carrier Access Network Device Axxius 800 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Carrier Access Network Device Axxius 800 you will learn all the available features of the product, as well as information on its operation. The information that you get Carrier Access Network Device Axxius 800 will certainly help you make a decision on the purchase.
If you already are a holder of Carrier Access Network Device Axxius 800, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Carrier Access Network Device Axxius 800.
However, one of the most important roles played by the user manual is to help in solving problems with Carrier Access Network Device Axxius 800. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Carrier Access Network Device Axxius 800 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
