Instruction/ maintenance manual of the product 300 Brinkmann
Go to page of 32
100 200 300 400 500 600 Sear Burner Lighting Instructions: 1. Open lid during lighting. 2. Push and turn control knob to “HIGH” and continue to push in. 3. Press electronic igniter and hold for 3 to 5 seconds. 4. Continue to push in control knob for 30 seconds after sear burner is lit.
1 WE W ANT Y OU T O ASSEMBLE AND USE Y OUR GRILL A S SAFEL Y A S POSSIBLE. THE PURPOSE OF THIS SAFETY ALER T S YMBOL IS T O A TTRA CT Y OUR A TTENTION T O POSSIBLE HAZARDS AS Y OU ASSEMBLE AND USE Y OUR GRILL.
2 FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT: General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 LP Gas Cylinder (Tank) Speci cations and Installation . . . . . . .
3 W ARNING • Leak test all connections bef ore rst use, even if gr ill was pur chased fully assembled and af ter each tank r e ll. Check the propane tank r ubber seal for damage.
4 LP GAS CYLINDER (T ANK) SPECIFICA TIONS AND INST ALLA TION: • Grill is hot when in use. T o av oid bur ns: • DO NO T at tempt to mo ve the grill. • Block the wheels so the unit does not accidentall y mov e . • W ear prot ective glov es or ov en mitts.
5 • Allow onl y quali ed licensed LP gas dealers t o proper ly ll or repair y our LP gas cylinder . • New tanks should be pur g ed pr ior to lling; infor m LP gas dealer if you ar e using a new tank. • DO NO T allow the cylinder t o be lled bey ond 80% capacity .
6 Tank Holder INS T ALLING THE LP GA S C YLINDER (T ANK) ONT O THE GRILL: 1. Chec k that the cylinder val ve is closed b y tur ning the knob cloc kwise. Inspect cylinder val ve rubber seal f or cracks or det er ioration. Do not use pr opane tank with damaged seal as a gas leak ma y occur .
7 HOSE AND REGULA T OR: Y our grill is equipped with a T ype 1 connection device with the f ollowing f eatures: 1 . The s yst em will not allow g as ow from the c ylinder until a positive connection t o the val ve has been made .
8 WHEN T O PERFORM A LEAK TEST : • Af t er assembling your g r ill and bef ore lighting f or the rst time , ev en if purchased full y assembled. • Ev er y time the LP gas c ylinder is re lled, ex changed or if any of the gas components ar e disconnected or replaced.
9 LIGHTING THE MAIN B URNERS: 1 . Open lid befor e lighting burner . 2. Make sur e all control knobs are in the “OFF” position. 3 . Select the b ur ner t o be lit. P ush and tur n the control knob of that burner to the “HIGH” position 4. P ress the electr onic igniter and hold f or 3–5 seconds to light b ur ner 5.
10 6. Repeat st eps 3–5 for lighting each b ur ner . Alw ay s use electronic ignit er for lighting each b ur ner . If burner does not ignite using the push-b ut ton ignit er , wait 5 minut es, see “Match Lighting the Main Bur ners” section. 7 . T o tur n of f , tur n each control knob cloc kwise until it locks in the “OFF” position.
11 • Read and f ollow all w arnings and instructions contained in the pr eceding sections of this manual. • Nev er use charcoal, lava r ocks or w ood briquets in a gas grill. Flav oring chips m ust be contained in a metal smoking bo x to contain ash and pr event res.
TURNING OFF THE GRILL: 1 . T urn off the c ylinder val ve. 2. T urn all bur ner contr ol knobs to the “OFF” position. Not e: T ur n of f LP cylinder rst to pr ev ent gas fr om being lef t in the sy stem under pr essure. C A UTION: • The cylinder v alv e should alw ay s be in the of f, or closed, position when the grill is not in use.
13 W ARNING: If a bristle br ush is used t o clean any of the cooking surf aces, ensure no loose bristles remain on the cooking surf aces pr ior t o gr illing as loose bristles ma y att ach to f ood.
14 BURNER A SSEMBL Y/MAINTENANCE: • Although y our burners are constructed of st ainless steel, they ma y corr ode as a result of the e xtreme heat and acids from cooking f oods. R egular ly inspect the b ur ner s for crac ks, abnor mal holes , and other signs of corrosion damage.
15 BEFORE S T ORING Y OUR GRILL: • Ensur e that the cylinder val ve is full y closed. • Clean all surf aces. Lightly coat the b ur ners with cooking oil t o pre v ent ex cess rusting. • If st or ing the grill indoors , disconnect the LP tank and leav e the LP tank OUTDOORS .
16 TROUBLE SHOOTING: Problem Possible Cause Prevention/Cur e Burner will not light LP gas tank v alv e is closed Make sur e regulator is secur ely at tached to the LP gas t ank, tur n LP gas tank v alv e to “ OPEN” LP gas tank is lo w or empt y Check if LP g as tank is empty .
17 Problem Possible Cause Prevention/Cur e Flame blows out High or gusting winds Do not use grill in high winds Low on LP g as Replace or r e ll LP gas tank Burner holes may be obstructed R efer to.
18 ASSEMBL Y INSTRUCTIONS: 8 M6 X 1 2 mm Bolts (Blac k) 1 7 M6 X 1 2 mm Bolts (Silv er) 4 M6 X 30 mm Bolts (Silv er) 2 M5 X 1 2 mm Bolts (Blac k) 2 M4 X 1 2 mm Bolts (Blac k) 8 M4 X 1 2 mm Bolts (SIl .
19 READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS C AREFULL Y BEFORE ASSEMBLING OR OPER A TING Y OUR GRILL. WE RECOMMEND TW O PEOPLE WORK T OGETHER WHEN A S SEM BLING THIS UNIT .
20 (Proof of purchase will be required.) Inspect contents of the bo x to ensur e all par ts are included and undamaged. 1 13 15 16 17 19 21 22 27 28 3 2 4 5 6 FOR COVERS, ACCESSORIES AND OTHER PRODUCT.
Choose a good, cleared assemb ly area and get a friend t o help you put your g r ill t ogether . Lay card board down t o prot ect grill nish and assembl y area. C A UTION: Some par ts ma y contain sharp edges. W ear prot ective glo ves if necessar y .
Step 3 Remo ve the spring, w asher , and bolt from the t ank gauge brac ket. Set aside f or use in Step 5. At tach the tank g auge brack et onto the base using t wo M6 X 1 2 mm bolts (sliv er) as illustrated in F igure 1 .
Step 6 Using f our M6 X1 2 mm bolts (silv er) at tach the lef t panel and the right panel to the cart base. Step 7 Using f our M6 X 1 2 mm bolts (silv er) at tach the bac k panel.
Step 8 T o at tach the wind de ector , inser t the upper car t brace pr e-att ached bolts through the k ey holes of the wind de ector , slide the wind de ector down war d and tighten the bolts securel y .
Step 1 0 With the help of a friend, place the grill body assembl y on the grill car t. Secure using f our M6 X 12 mm bolts (blac k) from the lef t and the r ight side of the frame . Step 1 1 T o at tach the lef t side table assembl y , r st inser t the side tab le ’ s xed stands ont o the grill body hooks (F igure 1).
26 Step 1 2 T o at tach the r ight side tab le assembl y , r st inser t the side tab le ’ s xed stands ont o the grill body hooks (F igure 1). Open the grill hood, then use one M5 X 1 2 mm bolts (blac k) and one M6 washer t o secure the right side tab le assembl y to the grill body from the inside (F igure 2).
27 Step 1 4 Remo ve the r etaining nut fr om the top of the thermocouple, and inser t the ther mocouple int o the hole in the sear burner as shown. Reat tach nut on the other side and tight en. Remo ve the pr e-at tached scre ws from the sear b ur ner .
28 Heat Tents Brackets Sear Burner Grate Step 1 6 Slide open the right side table , inser t the sear burner grat e. Step 1 7 Place the heat tents on lo wer le vel of grill body assembl y directl y abov e burners . Step 1 8 Place cooking grills on suppor t r ibs directl y abov e heat tents .
29 Step 20 Inser t the sear Bur ner gr ease tra y on the trac ks under sear burner in back. Step 21 At tach the tank heat shield under the gr ease tra y using t wo M4 X 1 2 mm bolts (blac k) (F igure 1). Slide the gr ease tra y onto the trac ks located behind and underneath the grill body assembl y .
Grease Cup Brinkmann ® 4580 (Assembled) 30 100 200 300 400 500 600 Sear Burner Lighting Instructions: 1. Open lid during lighting. 2. Push and turn control knob to “HIGH” and continue to push in. 3. Press electronic igniter and hold for 3 to 5 seconds.
©2012 The Brinkmann Corporation Dallas, Texas 75244 U.S.A. 140-4580-S 0812 Owner’s Manual for Model Manual del Propietario para el Modelo 810-4580-S The Brinkmann Corporation warrants to the origin.
An important point after buying a device Brinkmann 300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Brinkmann 300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Brinkmann 300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Brinkmann 300 you will learn all the available features of the product, as well as information on its operation. The information that you get Brinkmann 300 will certainly help you make a decision on the purchase.
If you already are a holder of Brinkmann 300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Brinkmann 300.
However, one of the most important roles played by the user manual is to help in solving problems with Brinkmann 300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Brinkmann 300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
