Instruction/ maintenance manual of the product 802c Bose
Go to page of 20
1 © 1997 Bose Corporation Part Number 129292 REV 03 Service Manual 802C System Controller Original and SMD V ersion ® ® Units with serial numbers beginning with 100000 are the original 802C's. Units with serial numbers beginning with 200000 are the new SMD 802C's.
2 Contents Safety Information ............................................................................................................................ 3 Electrostatic Discharge Sensitive (ESDS) Device Handling .....................................
3 SAFETY INFORMA TION 1. Parts that have special safety characteristics are identified by the symbol on schematics or by special notes on the parts list. Use only replacement parts that have critical characteristics recommended by the manufacturer . 2.
4 DEVICE HANDLING ELECTROST A TIC DISCHARGE SENSITIVE (ESDS) This unit contains ESDS devices. W e recommend the following precautions when repairing, replacing or transporting ESDS devices: • Perform work at an electrically grounded work station.
5 SPECIFICA TIONS Input C onnections: (per channel) O ne ( 1 ) balanced female XLR connector One (1) unbalanced 1/4" phone jack Output Connections: (per channel) Two (2) 1/4" phone jacks per.
6 The 802 ® C System Controller is a sophisticated signal processing device which combines the functions of three equalizers, an automatic switching circuit, and an electronic crossover .
7 DISASSEMBL Y/ASSEMBL Y PROCEDURES Figure 1. Locking T ab Screw Location Note: Refer to the Figures (2 and 3) for the following procedures. 1. T op Cover Removal 1.1 Remove the four screws (two located at the rear of the unit and one located on each side of the unit) that secure the top cover to the chassis.
Figure 2. Original 802C PCB Exploded Vi ew Figure 3. SMD 802C PCB Exploded Vi ew 8.
9 TEST PROCEDURES 4. Bi-Amp Frequency Response Note: This test is performed with both the 802 AMP and the 302 AMP output jacks used at the same time. 4.1 Apply a 750Hz, 500mV rms signal to the input of the 802C. 4.2 Reference a dB meter to the 802 AMP output jacks (while in the Bi-Amp mode).
10 TEST PROCEDURES 4.4 Apply a 100Hz, 500mV rms signal to the input of the 802C. 4.5 Reference a dB meter to the 302 AMP output jacks (while in the Bi-Amp mode). 4.6 Refer to the frequency response table below and verify the response of the unit. 6. Noise T est 6.
11 1. This part is not normally available from Customer Service. Approval from the Field Service Manager is required before ordering. 2. The individual parts located on the PCB are listed in the Electrical Part List. 3. This part is critical for safety purposes.
12 MAIN PART LIST Reference Designator Description Part Number Note J1, 3 CONNECTOR, XLR, INSERT 121823 J2, 4- 8 JACK, PHONE 121570 J 9 WAFER, 7PIN, (2461) 123237-07 J9 CONNECTOR, 7PIN (21458) 121970-.
Figure 4. Main Parts Exploded View 13.
14 ELECTRICAL PART LIST Resistors Reference Designator Description Part Number Note R1, 2 2.7k Ω , 1/4 Watt, 5% 117704- 1212725 R3, 4 3.3k Ω , 1/4 Watt, 5% 117704- 1213325 R5-7, 11, 15, 118, 218 160k Ω , 1/4 Watt, 5% 117704- 1211645 R8, 9, 12, 13, 16, 17, 101, 210, 104, 204 330k Ω , 1/4 Watt, 5% 117704- 1213345 R10, 14, 18 8.
15 ELECTRICAL PART LIST Resistors (continued) Reference Designator Description Part Number Note R144, 244 56k Ω , 1/4 Watt, 2% 117704- 1215632 R148, 248 4.12k Ω , 1/4 Watt, 1% 119976- 2214121 R149, 249 23.7k Ω , 1/4 Watt, 1% 119976- 2212372 R150, 250 30.
16 ELECTRICAL PART LIST Capacitors Reference Designator Description Part Number Note C 1 .0047uF, 220V .0047uF, 1.4KV, 100/120V 120993 103447 3 C2, 3 . 015uF, FILM 118091-153 C 4 .01uF, CERAMIC DISC 119696-103 C5, 6 470uF, ELECTROLYTIC 110704 C7-10 1uF, ELECTROLYTIC 119942-1R0 C11-19, 22 .
17 ELECTRICAL PART LIST Diodes T ransistors Integrated Circuits Reference Designator Description Part Number Note U1, 8, 9 QUAD OP AMP, LS-404 120535/192166 4 U 2 VOLT REG, 78L15 121116-1 U 3 VOLT REG, 79L15 121117-1 U4 QUAD NAND CD-4011 121854 U5, 6 QUAD OP AMP, RC4156 192166 4 U7, 10 QUAD AW.
18 VOL T AGE CONVERSION INSTRUCTIONS 220 V olt to 1 10 V olt Conversion 1 10 V olt to 220 V olt Conversion 1. 220 V olt to 1 10 V olt Conversion Note: Conversions must be performed with the line cord disconnected from any power source. Refer to Figure 3 below for the following procedures.
Figure 6. T op Cover Connection Diagram 19.
SPECIFICA TIONS AND FEA TURES SUBJECT TO CHANGE WITHOUT NOTICE ® ® Bose Corporation The Mountain Framingham Massachusetts USA 01701 P/N 129292 REV . 03 10/97 FOR TECHNICAL ASSIST ANCE OR P AR T ORDE.
An important point after buying a device Bose 802c (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bose 802c yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bose 802c - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bose 802c you will learn all the available features of the product, as well as information on its operation. The information that you get Bose 802c will certainly help you make a decision on the purchase.
If you already are a holder of Bose 802c, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bose 802c.
However, one of the most important roles played by the user manual is to help in solving problems with Bose 802c. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bose 802c along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
