
DRIVER’S HANDBOOK


ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils
Benefiting from the research applied to Formula 1,
lubricants are very high-tech products.
Updated with the help of RENAULT’s technical teams, this range is perfectly compatible with the
specific features of the brand’s vehicles.
f ELF lubricants enhance your vehicle’s performance significantly.
RENAULT recommends approved ELF lubricants for oil changes and top-ups. Contact your RENAULT Dealer or visit www.lubrifiants.elf.com
Une marque de

This Driver’s Handbook contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and
the technical developments it incorporates.
– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular main-
tenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too pleased to provide you with any additional information.
The following symbol will help you when reading this handbook:
To indicate a hazard, danger or safety recommendation.

The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This hand- book covers all items of equipment (both standard and optional) available for these models but whether or not these are fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the “approved Dealer” is your RENAULT Dealer.
Enjoy driving your new vehicle.
Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manu- facturer.



Getting to know your vehicle
Driving
Your comfort
Maintenance
Practical advice
Technical specifications
Alphabetical index



Key, radio frequency remote control: general information, use, deadlocking 1.2 Doors 1.6 Automatic locking when driving 1.10 Seat belts 1.12 Additional methods of restraint: 1.15
to the front seat belts 1.15 side protection 1.18 Child safety: general information 1.20
choosing a child seat mounting 1.23 fitting a child seat 1.24 deactivating, activating the front passenger airbag 1.27 Driving position 1.30 Warning lights 1.34
on-board computer 1.40 Steering wheel 1.48 Power-assisted steering 1.48 Clock and exterior temperature 1.49 Door mirrors 1.50 Audible and visual signals 1.51 Exterior lighting and signals 1.52 Windscreen washers and wipers 1.54 Fuel tank (filling with fuel) 1.56



B
Key, radio frequency remote control A or B
4 Locking/unlocking the key insert
for remote control B. To release insert 3 from its hous-
1 Locking the doors and luggage
ing, press button 4; it will come out automatically. To reinsert it in its housing, press
compartment lid.
2 Unlocking the doors and luggage
button 4 and guide insert 3 into the storage position.
compartment lid.
3 Ignition key, driver’s door and fuel
filler cap.
The key must not be used for any function other than those described in the handbook (removing the cap from a bottle, etc.).
Avoid leaving the remote control in hot, cold or humid areas.
Advice

Electric central locking
Locking/unlocking from the outside
This varies according to the environ- ment: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control.
In some cases, the radio frequency remote control may not work:
– if the vehicle is located in a zone of
For replacement, or if you require an additional remote control You must only contact an approved Dealer. – To replace a remote control, the
– if appliances are operating on the
same frequency as the remote con- trol (mobile phone, etc.);
– if the remote control battery is worn
vehicle must be taken to an ap- proved Dealer as both the vehi- cle and the remote control are needed to initialise the system. – Depending on the vehicle, you
or flat, etc.
Interference by factors in the immediate vicinity (external installations or the use of equipment operating on the same frequency as the remote control) may affect the operation of the remote con- trol.
have the option of using up to four remote controls.

Driver’s responsibility Never leave your vehicle with the key or remote con- trol inside and never leave a child (or a pet) unsupervised, even for a short while. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the doors. Risk of serious injury.
Remote control unit failure
Make sure that the correct battery type is being used, and that the battery is in good condition and in- serted correctly. These batteries have a service life of approximately two years. Refer to the information on the “Key, radio frequency remote control: bat- teries” in Section 5 for the battery changing procedure.
high electromagnetic radiation;

Remote controls A and B are used to lock or unlock the doors.
B
They are powered by a battery which must be replaced (refer to the informa- tion on the “Key/radio frequency remote control: batteries” in Section 5).
Pressing button 1 locks the doors and tailgate.
The side indicator lights and hazard warning lights flash twice to indicate that the doors have been locked.

Pressing button 2 unlocks the doors and tailgate.
Never leave your vehicle with the key or remote con- trol inside and never leave a child (or a pet) unsupervised, even for a short while. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the doors. Risk of serious injury.
The side indicator lights and hazard warning lights flash once to indicate that the doors have been unlocked.
To lock/unlock the doors from inside, refer to the information on “Central door locking/unlocking” in Section 1.
The key must not be used for any function other than those described in the handbook (removing the cap from a bottle, etc.).
Driver’s responsibility

Deadlocking of the doors and luggage compartment lid (for some countries)
Press button 1 twice in quick succes- sion.
This allows you to lock the doors and tailgate and to prevent the doors from being opened with the interior handles (by breaking the window and then trying to open the doors from the inside).
The hazard warning lights and indica- tor lights flash five times to indicate that the doors have locked.

Never use deadlocking if someone is still inside the vehicle.




As a safety precaution, the doors should only be opened or closed when the vehicle is stationary.

Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the doors. Also, in hot and/or sunny weather, please remember that the tempera- ture inside the passenger compart- ment increases very quickly. RISK OF DEATH OR SERIOUS INJURY.
Opening manually from the outside
Pull handle 1.
Using the key, unlock left-hand door lock 4. Place your hand under handle 5. Lift the handle and then pull the door towards you.
Depending on the vehicle, pull handle 2 or 3.

If you have left the lights on after switch- ing off the ignition, a warning buzzer will sound when the driver’s door is opened (to prevent the battery from going flat, etc.).
If you decide to keep the doors locked when you are driving, remember that it may be more difficult for those as- sisting you to gain access to the passenger compartment in the event of an emergency.
Driver’s responsibility


In the event of a fault with the electric windows:

Do not close the door by holding the window.
– The window does not lower when the
Make sure you do not place your fingers too high up in zone 7.
door is opened. If this happens, to close the door, proceed as described in the section entitled “In the event of a battery fault”.
Risk of injury.
– The window does lower when the
door is opened but does not close when the door is closed.
In these two cases, please refer to the paragraph entitled “Electric windows” in Section 3 to reinitialise the window system.
If the problem persists after re-initial- isation, please contact an authorised dealer.
In the event of a battery fault
Every time one of the doors is opened, the window lowers by a few millimetres to facilitate door move- ment. The window closes as soon as the door is closed. If there is any ice or snow prevent- ing the window from lowering when one of the doors is opened, this ice or snow must be removed to free the window before the door is closed. If you need to disconnect the bat- tery (breakdown etc.), lower the win- dows to make handling the doors easier whilst the battery is discon- nected.
With the vehicle unlocked:
the top of window 7 then pull the door gently towards you to prevent damage to seal 6;
of the window (zone 7) while holding the door to enable it to pass under seal 6, then close the door without banging it.
Door locking is accompa- nied by the windows clos- ing.
Risk of serious injury.


With the ignition on, the indicator light integrated in button 1 informs you of the status of the doors and luggage compartment lid:
– the indicator light is on when the
– when the doors are unlocked (or not
properly closed) the indicator light is off.
With the ignition switched off, when you lock the doors using the remote control, the indicator light stays on for about a minute, then goes out.
Electric central locking (depending on vehicle)
The door and luggage compartment can be locked and unlocked simultane- ously.

Lock or unlock by pressing button 1.
The doors cannot be locked/unlocked with a door open.
Never leave your vehicle with the key or remote con- trol inside.
If a door is open or not properly closed, the doors lock and then quickly unlock.
If you decide to keep the doors locked when you are driving, re- member that it may be more diffi- cult for those assisting you to gain access to the passenger compart- ment in the event of an emergency.
doors/tailgate are locked; · Driver’s responsibility


Using the interior door locking/un- locking control.
With the engine off and the driver’s door open, switch on the ignition and switch it off again.
Press button 1 for more than five sec- onds, then get out of the vehicle with the remote control with you and close the driver’s door.
When the door is closed, all the doors and the tailgate will be locked. The vehicle can only be unlocked from the outside with the ignition key, for the driver’s door.
Unlocking the doors and tailgate
Using the key Lock or unlock the doors on the driv- er’s side by inserting the key fully into lock 2, then turning it.
Using the radio frequency remote control (refer to the information on the “Key/Radio frequency remote control” in Section 1).
Make sure you have your remote control with you before you leave your vehicle.
From the outside, unlock the driver’s door using the ignition key (refer to the information on “Opening/Closing the doors” in Section 1).

You must first decide if you want to activate this function.
The door can be unlocked:
– by opening a door when stationary.
With the ignition on, press central door locking button 1 for about five seconds, until a double beep is heard.
– by pressing door unlocking button 1.
With the ignition on, press central door locking button 1 for about five seconds, until a double beep is heard.
If you find an operating fault (no au- tomatic locking, the indicator light for button 1 does not light up when trying to lock the doors and luggage com- partment lid, etc.), firstly check that the doors and luggage compartment lid are properly closed. If they are properly closed, contact an approved dealer.
When the vehicle is started, the system automatically locks the doors as soon as a speed of 4 mph (7 km/h) is reached.
The button’s indicator light 1 comes on.
If you decide to keep the doors locked when you are driving, remember that it may be more difficult for those as- sisting you to gain access to the passenger compartment in the event of an emergency.
To activate · To deactivate · Driver’s responsibility




Heated seats (depending on the vehicle)

For safety reasons, carry out any adjustments when the vehicle is not being driven.
Lift handle 1 to release. Release the handle once the seat is in the correct position and ensure that the seat is locked.
With the ignition on, press switch 3. The integrated indicator comes on.
The system, which has a thermostat, decides whether or not the heating is needed.
We would advise you not to recline the seatbacks too far to ensure that the effectiveness of the seat belts is not reduced.
To tilt the seatback
Make sure that the seatbacks are correctly locked in place.
Depending on the vehicle, lift handle 2. Release the handle once the seat is in the correct position and ensure that the seat is locked.
Use lever 4 to tilt the seatback to the desired position.
Nothing should be placed on the floor (area in front of driver) as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.

Always wear your seat belt when trav- elling in your vehicle. You must also comply with the legislation of the par- ticular country you are in.
Before starting, first adjust your driv- ing position, then ask all occupants to adjust their seat belts to ensure optimum protection.

first removed your coat or jacket). This is essential to ensure your back is positioned correctly; – adjust the distance between the
seat and the pedals. Your seat should be as far back as possible while still allowing you to depress the clutch pedal fully. The seatback should be adjusted so that your arms are slightly bent when you hold the steering wheel; – adjust the height of the seat. This
Sit with your back firmly against the seatback.
Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident.
Shoulder strap 1 should be as close as possible to the base of the neck but not on it.
adjustment allows you to select the seat position which offers you the best possible view; – adjust the position of the steering
Use one seat belt per person, whether child or adult.
Lap belt 2 should be worn flat over the thighs and against the pelvis.
Even pregnant women should wear a seat belt. In this case, ensure that the lap belt is not exerting too much pressure on the abdomen, but do not allow any slack.
wheel.
The seat belt should be worn so that it is as close as possible to your body, i.e.: avoid wearing heavy clothing or keeping bulky objects under the belts, etc.

ß Driver seat belt

This lights up if the driver’s seat belt is not fastened and, when the vehi- cle reaches a speed of approximately 6 mph (10 km/h), it flashes and a beep sounds for approximately 2 minutes before the light returns to being contin- uously lit.
Press button 4 on buckle 5 and the seat belt will be rewound by the inertia reel.
Guide the buckle to help the operation.
Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pull- ing on buckle 3).
If the belt jams, allow it to return slightly before attempting to unwind it again.
If your seat belt is completely jammed, pull slowly, but firmly, so that just over 3 cm unwinds. Allow it to return slightly before attempting to unwind it again.
If there is still a problem, contact an ap- proved dealer.


– No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer.
– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
– Never wear the shoulder strap under your arm or behind your back.
– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around
them.
– The belt should never be twisted.
– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as
they show any signs of wear.
– Make sure that the buckle is inserted into the appropriate catch.
– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly se-
cured.
– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or ob-
jects).

Depending on the vehicle, they are composed of:


– Have the entire restraint
system checked following an accident.
– seat belt pretensioners;
– chest-level load limiters;
– No operation whatso- ever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical.
– air bags for driver and front pas-
senger.
These systems are designed to act in- dependently or together when the ve- hicle is subjected to a frontal impact. Depending on the severity of the impact, the system can trigger:
– To avoid incorrect triggering of
the system which may cause injury, only qualified personnel from an approved dealer may work on the pretensioner and air bag system.
– seat belt locking;
– the seat belt inertia reel pretensioner
(which engages to correct seat belt slack);
The pretensioners hold the seat belt against the body, holding the occupant more securely against the seat, thus in- creasing the seat belt’s efficiency.
– the front air bags.
– The electric trigger system may
only be tested by a specially trained technician using special equipment.
Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level.
With the ignition on, if the vehicle is subject to a significant frontal impact the system may, depending on the se- verity of the impact, trigger inertia reel pretensioner 1 on the front seats.
– When the vehicle is scrapped,
contact an approved dealer for disposal of the pretensioner and air bag gas generators.


Fitted to the driver and passenger side.
Depending on the vehicle, the pres- ence of this equipment is indicated by the word “air bag” on the steering wheel and dashboard (air bag zone A) and a symbol on the lower section of the windscreen.
Each air bag system consists of:
– an air bag and gas generator fitted
on the steering wheel for the driver and in the dashboard for the front passenger;
– a shared computer, which includes
the impact detector and the moni- tor controlling the electrical trigger system for each of the gas genera- tors;
This system is only operational when the ignition is switched on.

The air bag system uses pyrotechnic principles. This explains why, when the air bag inflates, it will gener- ate heat, produce smoke (this does not mean that a fire is about to start) and make a noise upon detonation. In a situation where an air bag is required, it will inflate immediately and this may cause some minor, su- perficial grazing to the skin or other problems.
In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and of the front pas- senger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hin- dered when leaving the vehicle.
– remote sensors.
instrument panel;

All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates.

– Do not cover the steering wheel boss under any circumstances.
– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel boss.
– The steering wheel must not be removed (except by qualified personnel from our Network).
– When driving, do not sit too close to the steering wheel. Sit with your arms slightly bent (see the information on “Adjusting
your driving position” in Section 1). This will allow sufficient space for the air bag to deploy correctly and be fully effective.
– Do not place anything between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).
– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may occur. In
general, parts of the body should be kept away from the dashboard (knees, hands, head, etc.).
– The devices in addition to the front passenger seat belt should be reactivated as soon as a child seat is removed, to ensure
the protection of the passenger in the event of an impact.
A REAR-FACING CHILD SEAT MUST NOT BE FITTED TO THE FRONT PASSENGER SEAT UNLESS
THE ADDITIONAL RESTRAINT SYSTEMS, I.E. THE PASSENGER AIR BAG, ARE DEACTIVATED.
(refer to the information on “Child safety: deactivating/activating the front passenger air bag” in Section 1)

These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact.

– Fitting seat covers: seats equipped with an air bag require covers specifically designed for your vehicle. Contact an approved Dealer to find out if these covers are available. The use of any covers other than those designed for your vehicle (and including those designed for another vehicle) may affect the operation of the air bags and reduce your protection.
Depending on the vehicle, a mark- ing on the windscreen informs you of the presence of additional means of restraint (air bags, pretensioners, etc.) in the passenger compartment.
– Do not place any accessories, objects or even pets between the seatback, the
door and the internal fittings. Do not cover the seatback with any items such as clothes or accessories. This may prevent the air bag from operating correctly or cause injury when the air bag is deployed.
These air bags operate through slits in the front seatbacks (door side): never insert any objects in these slits.
– No work or modification whatsoever may be carried out on the seat or internal
fittings, except by qualified personnel from an approved dealer.

All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates.


The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times. If seat belts are not worn, the occupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor superficial injuries occurring when the air bag is deployed, although such minor injuries are always possible with air bags.
If the vehicle should overturn or suffer a rear impact, however severe, the pre- tensioners and air bags are not always triggered. Shocks to the underbody of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.
– No work or modification whatsoever may be carried out on any part of the air
bag system (air bags, pretensioners, computer, wiring harness, etc.), except by qualified personnel from an approved dealer.
– To ensure that the system is in good working order and to avoid accidental trig-
gering of the system which may cause injury, only qualified Network personnel may work on the air bag system.
– As a safety precaution, have the air bag system checked if your vehicle has
been involved in an accident, or is stolen or broken into.
If it does not light up when the ignition is switched on, or lights up while the engine is running, there is a fault in the system (air bags, pretensioners etc.).
– When selling or lending the vehicle, inform the user of these points and hand
over this driver’s handbook with the vehicle.
– When scrapping your vehicle, contact your approved dealer for disposal of the
gas generator(s).
Contact your approved dealer as soon as possible. Your protection will be re- duced until this fault is rectified.

Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility.
A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- ished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.

Driver’s responsibility when parking or stopping the vehicle
Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time.
They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the doors.

A collision at 30 mph (50 km/h) is the same as fall- ing a distance of 10 metres. Transporting a child without a restraint is the equivalent of allow- ing him or her to play on a fourth- floor balcony without railings. Never travel with a child held in your arms. In the event of an accident, you will not be able to keep hold of the child, even if you yourself are wearing a seat belt. If your vehicle has been involved in a road accident, replace the child seat and have the seat belts checked.
Also, in hot and/or sunny weather, please remember that the tempera- ture inside the passenger compart- ment increases very quickly.
RISK OF DEATH OR SERIOUS INJURY.
To prevent the doors being opened, use the “Child safety” device (refer to the information on “Opening and closing the doors” in Section 1).

Using a child seat The level of protection offered by the child seat depends on its ability to re- strain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact.
Set a good example by always fas- tening your seat belt and teaching your child: – to strap themselves in correctly. – to always get in and out of the car
at the kerb, away from busy traf- fic.
Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle. Consult an ap- proved dealer to find out which seats are recommended for your vehicle.
Do not use a second-hand child seat or one without an instruction manual.
Check that there are no objects in the vicinity of the child seat which could impede its operation.
Before fitting a child seat, read the manual and respect its instructions. If you experience any difficulties during installation, contact the manufacturer of the equipment. Keep the instructions with the seat.

Never leave a child unat- tended in the vehicle.
Check that your child is always strapped in and that the belt or safety harness used is correctly set and adjusted. Avoid wearing bulky clothing which could cause the belts to slacken.
Never let your child put their head or arms out of the window.
Check that the child is in the correct position for the entire journey, espe- cially if asleep.




Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this posi- tion as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell.
Forward-facing child seats The child’s head and abdomen need to be protected as a priority. A forward-fac- ing child seat which is firmly attached to the vehicle will reduce the risk of impact to the head. Ensure your child travels in a forward-facing seat with a harness or buckle for as long as their size permits. Choose a bucket type seat for optimum side protection.w
Booster cushions From 15 kg or 4 years, the child can travel using a booster seat, which will enable the seat belt to be adapted to suit his size and shape. The booster seat cushion must be fitted with guides to position the seat belt on the child’s thighs rather than the stomach. It is recommended that you use a seat- back which can be adjusted in terms of height to position the seat belt in the centre of the shoulder. It must never rest on the neck or on the arm. Choose a bucket type seat for optimum side protection.

Attachment via the seat belt
The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact.
Ensure that the strap paths indicated by the child seat manufacturer are re- spected.
Always check that the seat belt is cor- rectly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
The seat belt must never be twisted or the tension relieved. Never pass the shoulder strap under the arm or behind the back. Check that the seat belt has not been damaged by sharp edges. If the seat belt does not operate nor- mally, it will not protect the child. Consult an approved dealer. Do not use this seat until the seat belt has been repaired.
Check that the seat is correctly held by moving it from side to side and back to front: the seat should remain firmly fixed.
Check that the child seat has not been installed at an angle and that it is not resting against a window.
Do not use the child seat if it may unfasten the seat belt restraining it: the base of the seat must not rest on the buckle and/or catch of the seat belt.
No modifications may be made to the component parts of the restraint system (seat belts, seats and their mountings) originally fitted.

Some seats are not suitable for fitting child seats. The diagram on the follow- ing page shows you how to attach a child seat.
In the front seat The laws concerning children travel- ling in the front passenger seat differ in every country. Consult the legislation in force and follow the indications on the diagram on the following page.
The types of child seats indicated may not be available. Before using a differ- ent child seat, check with the manufac- turer that it can be fitted.
Before fitting a child seat in this seat (if authorised): – move the seat as far back as pos-
sible; – on equipped vehicles, raise the
seat base as far as possible; – gently tilt the seatback away from
vertical (approximately 25°).
Do not change these settings after the child seat is installed.
Check that when installing the child seat in the vehi- cle it is not at risk of coming loose from its base.
If you have to remove the headrest, check that it is correctly stored so that it does not come loose under harsh braking or impact.

RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this position, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front passen- ger air bag” in Section 1).
Always attach the child seat to the vehicle even if it is not in use so that it does not come loose under harsh braking or impact.
Children of a maximum height of 135 cm are permitted to occupy the front seat if the air bag is deactivated and a suitable restraint system is used. For passengers above this height, the air bag must remain active.


Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt.
² Seat not suitable for fitting child seats. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this position, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front passen- ger air bag” in Section 1).
Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child. They risk serious or even fatal injury.
Children are permitted to occupy the front seat if the air bag is deactivated and a suitable restraint system is used, up to a maximum height of 135 cm. For passen- gers above this height, the air bag must remain active.

The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected.
Type of child seat Weight of the child Passenger front seat (1) (2)
Carrycot fitted across the
< 10 kg X
Rear-facing shell seat Group 0 or 0 + < 13 kg U
Rear-facing seat Groups 0 + and 1 < 13 kg and 9 to 18 kg U
Forward-facing seat Group 1 9 kg to 18 kg U
Booster cushion Group 2 or 3
15 kg to 25 kg and 22 to 36 kg U
X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted.
(1) Put the vehicle seat as far back and as high as possible.

(2) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this position, check that the air bag has been deactivated (refer to the information on “Child safety: deactivating/activating the front passenger air bag” in Section 1).
Children are permitted to occupy the front seat if the air bag is deactivated and a suitable restraint system is used, up to a maximum height of 135 cm. For passengers above this height, the air bag must remain active.
vehicle Group 0




Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is trig- gered.
To deactivate the air bags: with the vehicle stationary, push and turn lock 1 to the OFF position.

With the ignition on, it is essential to
The passenger air bag must be activated or deactivated with the ignition off.
In order to fit a child seat to the front passenger seat when this is allowed, you must deactivate the front passen- ger seat additional restraint devices (side airbags and, depending on vehi- cle, front airbags, etc.).
check that warning light 2 ¹ is lit on the central display and, depend- ing on the vehicle, that the message “PASSENGERAIRBAG OFF” is dis- played.
If it is interfered with when the vehicle is being driven, indicator
lights å and © will come on.
This light remains permanently lit to let you know that you can fit a child seat.
Switch the ignition off then on again to reset the air bag in accordance with the lock.



The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions.
Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is trig- gered.


Operating faults
It is forbidden to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty.
You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact.
The passenger air bag must be activated or deactivated with the ignition off.
Allowing any other passenger to sit in that seat is not recommended.
If it is interfered with when the vehicle is being driven, indicator
To reactivate the air bags: when the vehicle is stationary, push and turn lock 1 to the ON position.
lights å and © will come on.
Contact your approved dealer as soon as possible.
With the ignition on, you must ensure that warning light 2 is off. The front passenger seat belt additional restraint systems are activated.
Switch the ignition off then on again to reset the air bag in accordance with the lock.


13 19 18 21 22
10 11 12

The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent.
7 Centre air vents.
16 Handbrake.
2 Stalk for:
8 Location for passenger air bag.
17 Cruise control/speed limiter control.
– direction indicator lights,
9 Side air vent.
18 Hazard warning lights switch.
10 Storage compartment.
19 Traction control system activation/ deactivation controls.
– front fog lights,
11 Heating and ventilation controls.
20 Steering wheel height adjustment control.
– rear fog light,
12 Location for radio or storage com- partment.
– horn.
21 Cruise control/speed limiter controls.
3 Instrument panel.
13 Gear lever.
22 Door mirror adjustment control.
14 Electric window controls, rotating hard roof opening/closing control.
4 Location for driver’s air bag.
23 Bonnet release.
15 Central door locking/unlocking con- trols.
– Trip computer information readout control and vehicle settings person- alisation menu.
– Driver and front passenger seat
belt unfastened and passen- ger air bag activated/deactivated warning lights
– exterior lights,



The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent.
7 Instrument panel.
15 Central door locking/unlocking con- trols.
2 Location for passenger air bag.
3 Centre air vents.
– Trip computer information readout control and vehicle settings person- alisation menu.
16 Handbrake.
17 Central door locking/unlocking con- trols.
18 Electric window controls, rotating hard roof opening/closing control.
– Driver and front passenger seat
9 Side air vent.
belt unfastened and passen- ger air bag activated/deactivated warning lights
10 Door mirror adjustment control.
19 Gear lever.
11 Cruise control/speed limiter controls.
20 Location for radio or storage com- partment.
12 Steering wheel height adjustment control.
5 Stalk for:
21 Heating and ventilation controls.
– direction indicator lights,
13 Traction control system activation/ deactivation controls.
22 Storage compartment.
23 Bonnet release.
– front fog lights,
– rear fog light,
14 Hazard warning lights switch.
– horn.
6 Location for driver’s air bag.
– exterior lights,

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.

Low fuel level warning light
Gear change indicator light
This comes on when the igni- tion is switched on and goes out after a few seconds. If it comes on when driv- ing accompanied by a beep, fill up with fuel as soon as possible. å
This light comes on to signal that an upshift is necessary.
Air bag warning light
This lights up when the ignition is switched on and goes out after a few seconds.
If it remains lit or comes on when the engine is running, it indicates a system fault.
Contact your approved dealer as soon as possible.
Instrument panel A: you can adjust the brightness from the trip computer and warning system.

If no lights or sounds are ap- parent, this indicates a fault in the instrument panel. This indicates that it is essential to stop immediately (as soon as traf- fic conditions allow). Ensure that the vehicle is correctly immobilised and contact an approved Dealer.

The © warning light means you should drive very carefully to an approved Dealer as soon as pos- sible. If you fail to follow this recom- mendation, you risk damaging your vehicle.

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
Ä
Dipped beam headlight telltale á
Door status warning light
It lights up when the ignition is switched on and a door is open or not properly closed. Δ Speed limiter and cruise
On equipped vehicles, the light comes on when the ignition is switched on then goes out.
– If it lights up continuously accompa- nied by the © indicator light, con- sult an approved dealer as soon as possible;
See the information on the “Speed lim- iter” and “Cruise control” in Section 2.
– If it flashes, reduce the engine speed until the light stops flashing. Contact an approved dealer as soon as possible.
This lights up when the igni- tion is switched on and goes out after a few seconds. It may come on with other warning lights on the instrument panel.
Right-hand direction indica- tor tell-tale light
Refer to “Emission control, fuel econ- omy and driving advice” in section 2.
If it lights up when the vehicle is being driven, it is advisable to stop at an ap- proved dealer soon.
control indicator lights · © Warning light

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
Handbrake “on” warning light and brake circuit inci- dent warning light
It switches off a few seconds after the ignition is switched on, if it does not light up, consult an approved dealer. It may light up at the same time as other warning lights, together with a beep. It indicates that it is essential to stop immediately (as soon as traffic conditions allow). Contact an approved dealer. Ú
If it comes on during braking and is ac- companied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an approved dealer. À
Battery charge warning light
Oil pressure warning light
This comes on when the igni- tion is switched on and goes out after a few seconds. If it comes on together with the ® warning light and a beep, it indicates that the electrical cir- cuit is overcharged or undercharged.
This lights up when the ignition is switched on and goes out after a few seconds.
Anti-lock braking warning light
If it comes on when you are driving ac- companied by the ® warning light and a beep, it is essential to stop and switch off the ignition.
This lights up when the ignition is switched on and goes out after a few seconds.
If it flashes on its own, this indicates that the battery is low. Stop as soon as traffic conditions allow and contact an approved dealer.
Check the oil level. If the level is normal, the indicator light is being lit by some- thing else.
If it does not go out after the ignition is switched on, or lights up when driving, there is a fault with the ABS. Braking will then be as normal, without the ABS system.
Consult an approved dealer.
Contact an approved dealer as soon as possible.
® STOP light

The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. WARNING LIGHTS (4/4)
Electronic Stability Program (ESP) and traction control (ASR) indicator light.

There are several reasons why the light may come on: refer to the information on the “Electronic stability program: ESP” and “traction control system: ASR” in Section 2. ™
Seat belt reminder light
If the driver’s seat belt is not fastened the light remains lit when the vehicle is started, then when the car reaches a speed of approximately 6 mph (10 km/h), it flashes and a beep sounds for approximately 2 minutes.
Central display 1 ™ seat belt reminder light.
¹ passenger air bag deactivation warning light.

The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY.


Rev counter 2 (rpm x 1000)
(km or miles per hour).
Depending on the vehicle, a beep sounds for 10 seconds approximately every 40 seconds as long as the ve- hicle is travelling at over 72 miles per hour (120 km/h).
Overspeed buzzer

The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY.

Coolant temperature indicator 4
In normal use, the needle should be po- sitioned before zone A. Under “inten- sive” operating conditions, the needle may approach this zone. This is not se- rious unless the ® warning light comes on, accompanied by a message on the instrument panel and a beep.
The needle shows the fuel level. When
it is at the minimum level, the L fuel warning light comes on, accompa- nied by a beep.
Depending on the vehicle, it includes: – the time; – the exterior temperature; – radio information.
Fill up as soon as possible.
Fuel gauge 3 · Information display 5



Press button 1 to repeatedly to scroll through the following information:
a) total mileage and trip mileage re-
b) journey parameters:
– fuel used; – average fuel consumption; – current fuel consumption; – estimated range; – distance travelled; – average speed;
c) oil change interval;
d) cruise control and speed limiter pro-
General reset and trip mileage recorder reset key 1
e) dashboard and instrument panel
This includes the following functions:
Press and hold button 1 to reset the trip mileage recorder. The display must be set to “Trip mileage recorder”.
f) trip log, operating faults and informa-
tion message readout.
Refer to the tables on the following pages for display examples.
– operating fault messages (associ-
ated with the © warning light);
– warning messages (connected to the
® warning light).
All these functions are described on the following pages.

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections Interpreting the display selected
a) Total mileage and trip mileage recorder
Fuel consumed since the last reset.
Average fuel consumption since the last reset.
This value is displayed after driving 400 metres and takes into account the distance travelled and the fuel used since the last time the reset button was pressed. 7.3 L/100
This value is displayed after a speed of approximately 20 mph (30 km/h) is reached. 8.6 L/100
b) Trip settings · Current fuel consumption

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections Interpreting the display selected
Estimated range with remaining fuel
This range takes into account the average fuel consumption since the last time the reset button was pressed.
The value is displayed after driving 400 metres.
Several minutes after the reserve light has come on (refer to the information on the “Instrument panel”), the estimated range will no longer be displayed.
Distance travelled since the last reset. 0.5 KM
The value is displayed after driving 400 metres. 78.9 KM/H
Average speed since the last reset.

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections Interpreting the display selected
c) Oil change interval
Distance/time remaining until the next oil change (displayed in miles/kilometres and months), then when the service nears, several scenarios are possible: – distance/time remaining less than 900 miles (1,500 km) or one month: de-
13770 KM
pending on the vehicle, the message “SERVICE DUE SOON” is displayed;
– distance/time remaining 0 miles/km or oil change date reached: depending
on the vehicle, the message “SERVICE DUE” is displayed when the selected display is “mileage before oil change”, accompanied by the 9 symbol and the © warning light.
The vehicle requires an oil change as soon as possible.
NB: depending on the vehicle, the interval between oil changes varies according to the driving style (frequent driving at low speed, door-to-door journeys, extensive use at idle speed, towing a trailer etc.). The distance remaining until the next oil change can therefore decrease more quickly in some cases than the actual distance travelled.
The oil change intervals are independent of the vehicle’s maintenance schedule: please refer to your vehicle’s Maintenance Document.
Resetting: to reset the mileage before an oil change, with the display showing “oil change”, press and hold one of the display reset buttons for approximately 10 seconds until the display shows the interval permanently. Refer to the previous pages.

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
selections Interpreting the display selected
d) Dashboard and instrument panel brightness management.
70 KM/H
e) Cruise control/speed limiter programmed speed.
Refer to the information on the “Cruise control/speed limiter” in Section 2.
70 KM/H
NO MESSAGE
AVAILABLE
Successive display:
– information messages (automatic lighting, etc.), – operating fault messages (check the injection system, etc.).
Examples of · f) Trip log

These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages.
Examples of messages Interpretation of messages
“ESP OFF” Indicates that you have deactivated the ASR function.
“AUTO LIGHTS DEACTIVATED” Indicates that the automatic lights function is deactivated.

These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given on the following pages.
Examples of messages Interpretation of messages
“CHECK ESP” Indicates a fault with the traction control system (refer to the information on the “Traction control system: ASR ” in Section 2).
“CHECK AUTO LIGHTS” Indicates an automatic lighting operating fault; contact an approved Dealer.

These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Examples of messages Interpretation of messages
“INJECTION FAULT” Indicates that the vehicle has a serious engine fault.
“STEERING FAULT” Indicates a fault in the vehicle’s power-assisted steering.
“LOW BATTERY” Indicates a fault with the battery charging circuit.
“BRAKING FAULT” Indicates a fault in the braking circuit.
“OIL PRESSURE FAULT” Indicates an oil pressure fault.
“ENGINE OVERHEATING” Indicates that the engine is overheating.


The steering may become stiff when driving or when the steering wheel is turned repeatedly. This is due to the power assistance overheating. In this case, it must be allowed to cool down.
The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed.
Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
Depending on the vehicle, the steering wheel position is adjustable.
Hold the steering wheel with one hand, lift lever 1 and position the steering wheel as desired. Lower the lever to lock the steering wheel.
With the engine switched off, or if there is a system fault, it is still pos- sible to turn the steering wheel. The force required will be greater.
Make sure that the steering wheel is correctly locked.
Never switch off the igni- tion when travelling down- hill, and avoid doing so in normal driving (assistance is not provided).

For safety reasons, only adjust the steering wheel when the vehicle is station- ary.
Never leave the steering wheel at full lock while stationary.
Operating faults · Variable power-assisted steering

External temperature indicator
With the ignition on, press button: 1 for the hours; 2 for the minutes.
Special note:
When the external temperature is be- tween –3°C and +3°C, the °C charac- ters flash (indicates risk of ice forma- tion).
Display A
With the ignition on, the clock and the exterior temperature are displayed.
As ice formation is related to climatic exposure, local air humidity and temperature, the external temperature alone is not sufficient to detect ice.
If the power supply is cut (battery disconnected, supply wire cut, etc.), the clock must be reset.
For your safety, we recom- mend that you do not adjust the clock while driving.
We recommend that you do not adjust these settings while driving.
External temperature indicator


Heated door mirrors (depending on vehicle)

The door mirrors are de-iced when the rear screen demisting/de-icing is active.
C D E
Door mirrors with electrical adjustment:
Interior rear view mirror
Its position can be adjusted. When driv- ing at night, to avoid being dazzled by the headlights of the vehicle behind, depress the little lever 2 located behind rear view mirror.
With the ignition on, move button 1: – position C to adjust the left-hand
The door mirror on the driv- er’s side has two clearly de- fined zones. Zone B shows what can normally be seen in an ordinary rear view mirror. For your safety, zone A increases the area you can see at the rear and to the side of your vehicle.
door mirror; – position E to adjust the right-hand
D is the inactive position.
The objects in zone A look much further away than they really are.
For safety reasons, carry out any adjustments when the vehicle is not being driven.
door mirror;



Press the end of the stalk 1.
Pull stalk 1 towards you to flash the headlights. 1
Hazard warning lights
Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it.
Press switch 2.
This switch activates all four direction indicators and the side indicator lights simultaneously. It must only be used in an emergency to warn other drivers that you have had to stop in an area where stopping is prohibited or unexpected, or that you are obliged to drive under spe- cial conditions.
When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the stalk may be held when changing lanes.
When the stalk is released, it automati- cally returns to 0.
Depending on the vehicle, the hazard warning lights may come on automati- cally under deliberate heavy decelera- tion. You can switch them off by press- ing switch 2.



Main beam headlights With the dipped headlights lit, pull stalk A towards you. An indicator light on the instrument panel will come on. To return to the dipped headlights posi- tion, pull stalk A towards you again. e Switching off the lights Return the stalk to its original position.
Lights-on warning buzzer
If the lights are on after the engine is switched off, a warning beep sounds when the driver’s door is opened to warn you that the lights are still on.
Turn end 1 of stalk A until the symbol is opposite mark 2.
With the engine running on vehicles fitted with a light sensor, the dipped beam headlights come on automati- cally as light begins to fade; the stalk does not need to be turned (position 0).
To deactivate or reactivate this function, move end 1 of stalk A twice consecu- tively from 0 to the side lights position, with the vehicle stopped and the igni- tion on.
Turn end 1 of stalk A until the symbol is opposite mark 2.
A bleep confirms the deactivation of this function, and two bleeps confirm its re- activation.
An indicator light on the instrument panel will come on.
Automatic operation · Manual operation

f
Turning off the fog lights
Turn centre ring 3 on stalk A until the symbol faces mark 4, then re- lease it.
Turn ring 3 again until mark 4 is oppo- site the symbol for the fog light that you wish to switch off. The corresponding indicator light on the instrument panel goes out.
Operation of the fog lights depends on the exterior lighting selected, and an in- dicator light will light up on the instru- ment panel.
The front and rear fog lights switch off when the exterior lights are switched off.
To avoid inconveniencing other road users, remember to switch off the rear fog light when it is no longer needed.
The front and rear fog lights do not op- erate in automatic mode.
They only come on when the end of
ring 4 is in position u or k.
Turn centre ring 3 on stalk A until the symbol faces mark 4, then re- lease it.
Operation of the fog lights depends on the exterior lighting position selected, and an indicator light will light up on the instrument panel.
When driving in fog or snow, or when transporting objects which are higher than the roof, the headlights do not come on automatically.

Before driving at night: check that the electrical equipment is in good con- dition. As a general precau- tion, check that the lights are not obscured (by dirt, mud, snow or ob- jects which could cover them).
Switching on the fog lights remains the responsibility of the driver: the indicator lights on the instrument panel inform you whether the fog lights are lit (indicator light on) or not (indicator light not on).
Special case


With the engine running, move stalk 1:
B automatic wiper function
When this position is selected, the system detects the presence of water on the windscreen and triggers wiping at a suitable wiping speed. It is possible to change the time be- tween sweeps by turning ring 2.
C normal wiping speed
D fast wiping speed
With the ignition on, move stalk 1:
When driving every time the vehi- cle stops, the wipers slow down, e.g. fast wiping speed is reduced to normal wiping speed.
As soon as the vehicle moves off, wiping will return to the speed originally selected.
The wipers will pause for sev- eral seconds between sweeps. Depending on the vehicle, it is pos- sible to change the time between sweeps by turning ring 2.
Any action on stalk 1 overrides and cancels automatic operation.
C normal wiping speed
D fast wiping speed
With the vehicle stationary, if for any reason the wipers cannot move (e.g. stuck to windscreen by ice), the system will automatically cut off the power supply to the wipers.

In snowy or icy conditions, make sure the wiper blades are not stuck by ice.
Keep an eye on the condition of the blades. Replace the wiper blades as soon as they begin to lose efficiency (approximately once a year).
When working in the engine compartment, ensure that the windscreen wiper stalk is in position A (park).
With the ignition on, pull stalk 1 towards you.
Check the condition of the wiper blades. You are responsible for their service life:
A short pull triggers one sweep cycle of the wiper. A longer pull triggers three sweeps followed by a final sweep after several seconds.
Risk of injury.
the blades and the windscreen regularly with soapy water;
– do not use them when the wind-
Before any action involving the windscreen (washing the vehicle, de-icing, clean- ing the windscreen, etc.) return stalk 1 to position A (park).
– free them from the windscreen
when they have not been used for a long time.
In all cases, replace them as soon as they begin to lose efficiency: ap- proximately once a year.
Risk of injury and/or damage.
screen is dry;


Filling with fuel
Use a high grade fuel with the appro- priate octane rating as defined by the particular standards in force in your country.
Using leaded petrol will damage the antipollution system and may lead to a loss of warranty.
To ensure the fuel tank is not filled with leaded petrol, the fuel tank filler neck contains a restrictor fitted with a valve which only allows the nozzle for unleaded petrol to be used (at the pump).
It is essential to use unleaded petrol. The octane rating (RON) must con- form with the specifications given on the label inside fuel filler flap A. Refer to the information on “Engine specifica- tions” in Section 6.
– Insert the nozzle as far as it will go
so that the valve is opened.
– Keep the nozzle in this position
throughout the entire filling opera- tion.
Capacity of the fuel tank: 40 litres ap- proximately.
When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be suffi- cient space in the fuel tank to allow for expansion.
To open the compartment, place your finger into recess 2, then pull the cover.
Fuel filler cap: this is spe- cific to the vehicle type. If you have to replace it, make sure the new cap is of the same type. Contact an approved Dealer.
For details on filling the fuel tank, refer to the information on “Filling with fuel” on the next page.
Cap holder 1 is provided on the fuel filler flap for holding the cap when the tank is being filled.
Never place the cap near a source of heat or flame.
Do not wash the filler area with a high-pressure washer.
After filling, check that the cap and cover are closed.


Do not mix even small amounts of petrol (un- leaded or E85) with diesel. Do not use ethanol-based fuel if your vehicle is not compatible with this fuel. Do not add additive to the fuel – otherwise you risk damaging the engine.

If you notice a persistent smell of fuel you should:
– stop the vehicle as soon as traf-

No modifications what- soever are permitted on any part of the fuel supply system (computers, wiring, fuel circuit, injector, protection covers, etc.) as this may be danger- ous (such work must be undertaken by qualified Network personnel).
fic conditions allow and switch off the ignition;
– switch on the hazard warning
lights and ask your passengers to leave the vehicle and to keep away from the traffic;
– contact an approved dealer.



Running in 2.2 Ignition switch 2.2 Starting, stopping the engine 2.3 Special features of petrol versions 2.4 Gear lever 2.5 Handbrake 2.5 Advice on emission control and fuel economy 2.6 Environment 2.9 Driver correction devices and aids 2.10 Speed limiter 2.13 Cruise control 2.16

Up to 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm.

The ignition is on and the engine can be started.
You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km).
If the engine fails to start at the first at- tempt, turn the key back before activat- ing the starter again. Release the key as soon as the engine starts.
Service intervals: please refer to your vehicle’s Maintenance Document.
“Off and steering locked” position St
To lock: remove the key and turn the steering wheel until the steering column locks.
To unlock: turn the key and the steering wheel slightly.
When the ignition is switched off, any accessories (radio, etc.) will continue to function.
“Ignition” position M · “Start” position D · “Accessories” position A


With the engine idling, turn the key back to “Stop” position St.

Never leave your vehicle with the key or remote con- trol inside the vehicle and never leave a child (or a pet) unsu- pervised, even for a short while.
There is a risk that they could start the engine or operate electrical equipment (electric windows etc.) and trap part of their body (neck, arms, hands, etc.). Risk of serious injury.
Engine warm or cold:
– Turn the ignition key to “Start” posi-
tion D without accelerating;
Never switch off the ignition before the vehicle has stopped completely. Once the engine has stopped, the brake servo, pow- erassisted steering, etc., and the passive safety devices such as air bags and pretensioners will no longer operate.
– release the key as soon as the
engine starts.
Special note: if starting the engine when the outdoor temperature is very low (below - 10 ° C): hold down the clutch pedal until the engine starts.
The steering is locked when the key is removed.
Driver’s responsibility

The following operating conditions:
If you notice any of the above operating faults, have the necessary repairs car- ried out as soon as possible by an ap- proved Dealer.
– driving for long periods when the low
fuel level warning light is lit;
– using leaded petrol;
These faults may be avoided by regu- larly taking your vehicle to an approved Dealer at the intervals specified in the Maintenance Service Booklet.
– using fuel or lubrication additives
which are not approved.
Or operating faults such as:
– faulty ignition system, running out of
fuel or disconnected spark plugs re- sulting in the engine misfiring or cut- ting out when driving;
To avoid damaging the catalytic con- verter, do not keep trying to start the engine (using the start button, or by pushing or towing the vehicle) without having identified and corrected the starting fault.
– loss of power,
as they may cause the catalytic con- verter to overheat and thus reduce its efficiency, or damage it irreparably and cause heat damage to the vehi- cle.
If the fault cannot be identified, do not keep trying to start the engine, but con- tact an approved Dealer.

Do not park the vehicle or run the engine in locations where combustible sub- stances or materials such as grass or leaves can come into contact with the hot exhaust system.



To release:
Pull lever 2 up slightly, press button 3 and then lower the lever to the floor.
To apply:
Pull the lever 2 upwards and make sure the vehicle is immobilised.

Make sure that the hand- brake is properly released when driving (red indicator light off), otherwise over- heating may occur.
With the vehicle stationary, move the gear lever into neutral then into reverse.

An impact to the underside of the vehicle when revers- ing (e.g. striking a raised kerb) may result in damage to the vehicle (eg. deformation of the rear axle).
Follow the grid shown on knob 1.
The reversing lights will come on as soon as reverse gear is selected (with the ignition on).

Depending on the gradient and/or vehicle load, it may be necessary when station- ary to apply the brake by at least a further two notches and engage a gear (1st or reverse gear).
To avoid any risk of accident, have your vehicle checked by an ap- proved Dealer.
Selecting reverse gear

By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipol- lution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is main- tained and used correctly.
Engine adjustments
It is important to remember that failure to respect antipollution regulations could lead to legal action being taken against the vehicle owner. In addition, replacing engine, fuel supply system and exhaust components with parts other than those originally recommended by the manu- facturer may alter your vehicle so that it no longer complies with antipollution regulations.
justment.
omy, efficiency and performance the specifications laid down by our Design Department must be strictly applied.
If the spark plugs have to be changed, use the make, type and gap specified for your vehicle’s engine. Contact an approved dealer for this.
Have your vehicle adjusted and checked by an approved Dealer, in ac- cordance with the instructions given in your maintenance schedule: they will have all the equipment necessary for ensuring that your vehicle is maintained to its original standard.
ment.
reduce efficiency. It must be re- placed.


– Avoid sudden acceleration. – Brake as little as possible. If you an-
ticipate an obstacle or bend in ad- vance, you may then simply release the accelerator pedal. – Do not try to maintain the same
The exhaust gas monitoring system will detect any operating faults in the vehi- cle’s antipollution system.
If this system malfunctions, toxic sub- stances may be released into the at- mosphere or damage may occur. Ä
speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal. – Double declutching and accelerating
This warning light on the in- strument panel will indicate if there are any faults in the system: This lights up when the ignition is switched on and goes out when the engine is started.
before switching off are unnecessary in modern vehicles. – Bad weather, flooded roads:
Do not drive through floods if the depth of water is above the lower edge of the wheel rims.
– If it lights up continuously, consult
Driving – Drive carefully for the first few miles
your approved dealer as soon as possible;
until the engine reaches its normal operating temperature, rather than let it warm up while the vehicle is sta- tionary. – Speed is expensive. – Sporty driving uses a lot of fuel: drive
– if it flashes, reduce the engine speed
until the light stops flashing. Contact your approved dealer as soon as possible.

Obstructions to the driver On the driver’s side, only use mats adapted to the ve- hicle that attach to the pre- installed parts, and regularly check their mounting. Do not place several mats on top of each other. Risk of pedals jamming
with a light right foot. – Do not overrev the engine in the in-
termediate gears. Always use the highest gear possi- ble without labouring the engine.


– For vehicles fitted with air condi-

tioning, it is normal to observe an increase in fuel consumption (es- pecially in city conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Advice for reducing consumption and therefore helping to preserve the environment: Drive with the air vents open and the windows closed.
If the vehicle has been parked in the sun, open the doors for a few mo- ments to let the hot air escape before starting the engine.
Tyres
– Electricity is fuel; switch off all the
– Never fill the fuel tank right to the
– An under-inflated tyre increases fuel
brim to avoid overflow.
electrical components which are not really needed. However (safety first), keep your lights on when the visibility is bad (“see and be seen”).
consumption.
– Avoid using the vehicle for door-
– The use of non-recommended tyres
to-door calls (short journeys with long waits in between) because the engine never reaches its normal op- erating temperature.
can increase fuel consumption.
– Use the air vents. Driving with the
windows open at 60 mph (100 km/h) will increase fuel con-sumption by 4%.

Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the of the manufacturer eco² signature.
– At the end of the vehicle’s service
life, it should be sent to approved centres to ensure that it is recycled.
Your vehicle has been designed to emit fewer greenhouse gases (CO2) while in use, and therefore to consume less fuel (eg. 140 g/km, equivalent to 5.3 l/100 km for a diesel vehicle).
– In all cases, comply with local legis-
lation.
Manufacture
Our vehicles are also equipped with a particle filter system including a cata- lytic converter, an oxygen sensor and an active carbon filter (the latter pre- vents vapour from the fuel tank being released into the open air).
Your vehicle is 85% recyclable and 95% recoverable.
Your vehicle has been manufactured at a factory which complies with a policy to reduce the environmental impact on the surrounding areas (reduction of water and energy consumption, visual and noise pollution, atmospheric emis- sions and waste water; sorting and re- using waste).
To achieve these objectives, many of the vehicle components have been de- signed to enable them to be recycled. The materials and structures have been carefully designed to allow these components to be easily removed and reprocessed by specialist companies.
For certain diesel vehicles, this system also has a particle filter to reduce the volume of soot particles emitted.
In order to preserve raw material re- sources, this vehicle incorporates nu- merous parts made from recycled plas- tics or renewable materials (vegetable or animal-derived materials such as cotton or wool).
– Worn parts replaced in the course of
routine vehicle maintenance (vehi- cle battery, oil filter, air filter, batter- ies, etc.) and oil containers (empty or filled with used oil) must be disposed of through specialist organisations.

Depending on the vehicle, this is com- posed of: – the (ABS) (anti-lock braking
ABS (anti-lock braking system) Under heavy braking, the ABS prevents the wheels from locking, allowing the stopping distance to be managed and keeping control of the vehicle.
Operating faults:
system); – the electronic stability program
lights on the instrument panel come on, braking is still operational but without ABS;
(ESP) with understeer control and traction control (ASR); – emergency brake assist.
– If the x, ®, © and D indicator lights on the instru- ment panel come on when driving, this indicates a fault with the braking and ABS systems.
Under these circumstances, the vehi- cle can be steered to avoid an obstacle whilst braking. In addition, this system can increase stopping distances, par- ticularly on roads with low surface grip (wet ground etc.).

You will feel a pulsation through the brake pedal each time the system is activated. The ABS does not in any way improve the vehicle's physical perform- ance relating to the road surface and roadholding. It is still essential to follow the rules of good driving practice (such as driving at a safe distance from the vehicle in front etc.).
In both cases, consult an approved Dealer.
These functions are an ad- ditional aid in the event of critical driving conditions, enabling the vehicle behav- iour to be adapted to suit the driving conditions.
However, the functions do not take the place of the driver. They do not increase the vehicle’s limits and should not encourage you to drive more quickly. Therefore, they can under no circumstances replace the vigilance or responsibil- ity of the driver when manoeuvring the vehicle (the driver must always be ready for sudden incidents which may occur when driving).
Your braking systems are partially operational. However, it is dangerous to brake suddenly and it is essential to stop immediately, as soon as traffic conditions allow. Contact an approved dealer.
In an emergency, apply firm and continuous pressure to the brake pedal. There is no need to pump it repeatedly. The ABS will modu- late the force applied in the braking system.


Electronic stability program ESP
This system helps you to keep control of the vehicle in critical driving condi- tions (avoiding an obstacle, loss of grip on a bend, etc.).
This system helps to limit wheelspin of the drive wheels and to control the ve- hicle when pulling away accelerating or decelerating.
Operating principle A sensor in the steering wheel detects the direction selected by the driver.
Operating principle Using the wheel sensors, the system measures and compares the speed of the drive wheels at all times and slows down their over-rotation. If a wheel is starting to slip, the system brakes au- tomatically until the drive supplied be- comes compatible with the level of grip under the wheel again.
Other sensors throughout the vehicle measure the actual direction.
The system compares the direction se- lected by the driver and the actual di- rection of the vehicle and corrects this as necessary by applying the brakes selectively and/or acting on the engine power.
The system also adjusts the engine speed to the grip available under the wheels, independently of the pressure exerted on the accelerator pedal.
Indicator light 1 ù on the instru- ment panel flashes when the function starts operating.
This system optimises the action of the ESP in the case of pronounced unders- teering (loss of front axle road holding).
Traction control (ASR) · Understeer control


This is an additional system to ABS which helps reduce vehicle stopping distances.
The system detects an emergency braking situation. In this case, the brak- ing assistance immediately develops maximum power and may trigger ABS regulation.
ABS braking is maintained as long as the brake pedal is not released.
Hazard warning lights switching on Depending on the vehicle, these may light up in the event of sudden decel- eration.
Operating faults
The function is deactivated by press-
When the system detects an operating
ing switch 2 and indicator light 1 ù lights up on the instrument panel. This action also deactivates the traction con- trol.
fault, the © and ù warning lights on the instrument panel come on.
Consult an approved dealer.
The E.S.P. offers additional safety, it is recommended that you do not drive with the function disabled. Correct this by pressing switch 2 again.
The E.S.P. is automatically reactivated when the ignition is switched on.
Operating principle




The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed.
Switching on
1 Main “On/Off” switch.
Press switch 1 on the side showing . Indicator light 6 comes on, lit orange, and the message “SPEED LIMITER” appears on the instrument panel, ac- companied by dashes to indicate that the speed limiter function is activated and waiting to memorise a limit speed. To memorise the current speed, press switch 2 (+): the minimum speed which can be memorised is 20 mph (30 km/h).
2 Limit speed activation, storage and increase switch (+).
3 Limit speed activation, storage and decrease switch (-).
4 Switch the function to standby, with limit speed stored (O).
5 Stored limit speed activation, stor- age and recall (R).

Exceeding the limit speed
The limit speed may be changed by re- peatedly pressing:
It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point).
– Switch 2 (+) to increase the speed;
– Switch 3 (-) to decrease the speed.
Whilst the speed is being exceeded, the limit speed displayed on the instru- ment panel flashes.
Then, as far as is possible, release the accelerator pedal: the speed lim- iter function will return as soon as you reach a speed lower than the memo- rised speed.
Limited speed cannot be maintained
When driving down a steep gradient, the system is unable to maintain the limit speed: the memorised speed will flash on the instrument panel informa- tion display to inform you of this situ- ation.
When a limited speed has been stored and this speed is not reached, driving is similar to driving a vehicle without the speed limiter function.
Once you have reached the stored speed, no effort on the accelera- tor pedal will allow you to exceed the programmed speed except in an emergency (refer to information on “Exceeding the limit speed”).

The speed limiter function is in no way linked to the brak- ing system.

If a speed has been stored, it can be re- called by pressing switch 5 (R).
Switching off the function
The speed limiter function is interrupted when you press switch 1. In this case, the speed is no longer memorised. The orange indicator light on the instru- ment panel goes out, confirming that the function is deactivated.
The speed limiter function is sus- pended when you press switch 4 (O). In this case, the limit speed remains memorised and the message “SPEED MEMORY” accompanied by this speed appears on the instrument panel.
When the speed limiter is sus- pended, pressing switch 2 (+) or 3 (-) reactivates the function without taking into account the memorised speed: it is the speed at which the vehicle is moving that is taken into account.


This function is an addi- tional driving aid. However, the function does not take the place of the driver.
Therefore, it can under no circum- stances replace the driver’s respon- sibility to respect speed limits and to be vigilant (the driver must always be ready to brake).
The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed.
1 Main “On/Off” switch.
2 Cruising speed activation, storage and increase switch (+).
This cruising speed may be set at any speed above 20 mph (30 km/h).
Cruise control must not be used in heavy traffic, on winding or slip- pery roads (black ice, aquaplan- ing, gravel) and during bad weather (fog, rain, side winds etc.).
3 Cruising speed activation, storage and decrease switch (-).
4 Switch the function to standby (with stored cruising speed) (O).
There is a risk of accidents.
5 Cruising speed activation, storage and recall switch (R).

The cruise control function is in no way linked to the braking system.


Activating cruise control At a steady speed (above 20 mph (30 km/h) approximately) press switch 2 (+) or 3 (-): the function is ac- tivated and the current speed is memo- rised. Cruise control activation is confirmed when indicator light 7 lights up in addi- tion to indicator light 6.
Press switch 1 on the side showing .
Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelera- tor pedal.


The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel.
Then, release the accelerator pedal: after a few seconds, the vehicle will automatically return to its set cruising speed.
Cruising speed cannot be maintained
When driving down a steep gradient, the system is unable to maintain the cruising speed: the stored speed will flash on the instrument panel informa- tion display to inform you of this situ- ation.
The cruising speed may be changed by pressing the following repeatedly:
– switch 2 (+) to increase the speed,
– switch 3 (-) to decrease the speed.
The cruise control function is in no way linked to the braking system.

If a speed is stored, it can be recalled, once you are sure that the road condi- tions are suitable (traffic, road surface, weather conditions, etc.).
With a vehicle speed above 20 mph (30 km/h), press switch 5 (R).
Putting the function on standby
The cruise control function is deacti- vated if you press switch 1: in this case a speed is no longer memorised.
The function is suspended when you: – button 4 (O); – depress the brake pedal; – the clutch pedal or shift into neutral
The and indicator lights on the instrument panel go out, confirming that the function is deactivated.
if the vehicle has an automatic gear- box.
In all three cases, the cruising speed remains memorised and the message “SPEED MEMORY” appears on the in- strument panel. Standby is confirmed when the green indicator light goes out.
When the cruise control is set to standby, pressing switch 2 (+) re- activates the cruise control func- tion without taking into account the stored speed: it is the speed at which the vehicle is moving that is taken into account.

Putting the cruise control on standby or switching it off does not cause a rapid reduction in speed: you must brake by depressing the brake pedal.



Rotating hard roof 3.2 Air vents 3.6 Manual air conditioning/heating system 3.8 Automatic climate control 3.12 Electric windows 3.19 Interior lighting 3.20 Sun visor 3.20 Passenger compartment storage space and fittings 3.21 Accessories socket – Ashtray 3.23 Luggage compartment 3.24 Transporting objects in the boot 3.25 Multimedia equipment 3.26


Immobilise the vehicle on a flat, level surface (never with the wheel on the pavement).
Apply the handbrake.
Temperature above -10°C.

Never unlock the roof while driving.
Perform the operation with the engine running if possible (risk of discharging the battery).
Risk of damage to the roof and roof cover.
To prevent the system from overheat- ing, it cuts out automatically. It becomes operational again after a maximum of 30 minutes.
Never leave your vehicle with the key or remote con- trol inside and never leave a child (or a pet) unsupervised, even for a short while. He/she may be able to operate the rotating hard roof and there is a risk of trapping his/her neck, arm, hand, etc., which could cause serious in- juries. If anything is trapped, reverse the rotating hard roof’s direction of travel immediately by pressing the opposite side of the roof open/close button.
Before opening/closing the roof, check that there is sufficient space above the vehicle to allow it to open.
Minimum height required A: 2.05 m.

When opening or clos- ing the roof, ensure that nothing interferes with the moving parts (roof and roof cover).
Do not drive with the roof unlocked.
Do not open or close the roof if the wind speed is more than 20 mph (30 km/h) (risk of damage to the roof).
Driver’s responsibility



Make sure there are no objects in the way of the roof’s operating area. Make sure that there are no objects resting on the roof or roof cover. Make sure that the luggage compart- ment lid is properly closed.
Unlock the roof by pulling and turning control 1 clockwise. Please note: only unlocking is manual – do not lift up the roof. Push switch 2 down and hold it until the roof is fully open. The message “ROOF OPENING” appears on the instrument panel accompanied by squares which indicate the progress. The side win- dows and the roof cover open, the roof moves into its housing and the roof cover closes. If the message “ROOF OPENED” ap- pears on the instrument panel accom- panied by a beep, release switch 2.
Closing the roof Lift switch 2 and hold it until the roof is fully closed. The side windows and roof cover open. The message “ROOF CLOSING” appears on the instrument panel accompanied by squares which indicate the progress. The roof and its cover close. If the message “LOCK ROOF LATCH” appears on the instru- ment panel accompanied by a beep, re- lease switch 2.
Pull and lock the roof by turning con- trol 1 anticlockwise. The windows do not rise automatically at the end of the roof closure cycle. Lift the electric window switches to raise the windows.
To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts.




The roof unlocks but does not open
Remove plastic cover 2 to access the screw.
Use the emergency key supplied in the glove box to turn the screw clockwise until the roof cover opens sufficiently (point of resistance).
Check that the luggage compartment lid is properly closed. Restart the oper- ation: lock then unlock the roof without pushing it upwards.
To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts.
If there is a system fault, you can close the rotating hard roof.
To do this, open the roof cover manu- ally.
When opening/closing the roof, ensure that nothing interferes with the moving parts (roof and roof cover). Ensure that there are no objects in roof/roof cover area A.
Unclip logo 1 on the luggage compart- ment lid.


Close the roof again manually (move- ment B), making sure that there is no contact with the roof cover.
Engage plastic cover 2 in its housing.
Pull and turn control 3 anticlockwise to lock the roof.
Clip on the logo.
Consult an approved dealer.
Lower the roof cover using the emer- gency key to turn the screw anticlock- wise until the roof cover closes (point of resistance).
If the message “CHECK ROOF” ap- pears on the instrument panel con- tinually or when the roof open/close switch is pressed, consult an ap- proved dealer.


1 left-hand side air vent
2 windscreen demister outlets
3 centre air vents
4 right-hand side air vent
5 passenger footwell heater outlets
6 air conditioning control panel.


To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer.
To open, press on the air vent.
Turn the vent to position it.

Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours).
There is a risk of damage or of fire.


Distribution of air in the passenger compartment
Turn control A . W
Close the dashboard vents for more effective demisting. All the air flow is directed to the wind- screen demisting vents. i
The air flow is distributed be- tween the air vents, the wind- screen demisting vents and the foot- wells. F
The air flow is directed mainly towards the footwells.
Information and advice for use:
Refer to the end of the paragraph on “Automatic climate control”.
A Adjusting the distribution of air in the
passenger compartment.
B Heated rear screen and heated door
mirror de-icing/demisting control and indicator light.
C Adjusting the ventilation speed.
D Air recirculation and isolation of the
passenger compartment.
E Air conditioning operating indicator
light and button.
F Adjusting the air temperature.

Adjusting the ventilation speed
Turn control C from 0 to 4.
The passenger compartment is ven- tilated by blown air. The blower deter- mines how much air enters but vehicle speed has a slight effect on this.
The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment.
The air flow is directed towards the dashboard vents and the footwells. J
With the engine running, press button B, the operating tell-tale for the button will come on.
All the air flow is directed to the dashboard vents.
This selection is not appropriate if all the air vents are closed.
This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehi- cles).
To exit this function, press button B again.
Demisting automatically stops by de- fault.

Prolonged use of this position (iso- lation mode) may mist up the win- dows slightly or cause odours due to the air not being renewed. It is therefore advisable to return to normal operation (external air) by pressing control D when you have passed through the polluted area.
Air recirculation is for:
– isolating the vehicle from the exter-
nal atmosphere (driving in polluted areas, etc.);
Turn control D towards air recirculation symbol â.
– bringing the passenger compartment
to the desired temperature as quickly as possible.
In these conditions air is taken from the passenger compartment and is recircu- lated, with no air being taken from out- side the vehicle.

Air conditioning control
Use the air recirculation function to lower the temperature as quickly as possible to the required level. Switch off the air recirculation function once a comfortable level has been reached.
The air conditioning is switched on (in- dicator light on) or off (indicator light off) using button E.
The system cannot be switched on if control C is set to 0.
The air conditioning system is used for:
– lowering the temperature inside the
– eliminating condensation more
quickly.
passenger compartment;


Information and advice for use
Refer to information on “Air condition- ing: information and advice on use”.
Controls (depending on vehicle)
6 and 8 Adjusting the ventilation speed.
1 “Clear view” button for demisting and de-icing the windows and/or heated door mirrors.
7 and 9 Passenger compartment air distribution adjustment.
10 and 11 Adjusting the air tempera- ture.
3 Air conditioning on/off button.
12 Heated rear screen and/or heated door mirror de-icing.
4 Starting automatic mode.
Buttons 1 and 12 are comple- mented by operating indicator lights (2 and 13):
5 Display.
14 Air recirculation control.
– indicator light on, the function is
– indicator light off, the function is
switched off.
switched on,


Only the temperature and the AUTO symbol are displayed
Functions managed in automatic mode are not displayed.
– press button 10 to increase the tem-
– press button 11 to decrease the tem-
perature.
To reach and keep the chosen comfort level and to maintain good visibility, the system controls:
Press button 4. AUTO lights up on dis- play 5.
In most cases, the automatic climate control system ensures a comfortable temperature in the passenger compart- ment, while maintaining good visibility and optimising fuel consumption.
– air recirculation management;
– air conditioning start/stop;
This is the recommended mode of use.
– the air temperature.
In automatic mode (AUTO lit on the display), all heating and air condi- tioning functions are controlled by the system.
When you modify certain functions, AUTO goes out. Only the modified function stops being controlled by the system.
perature; · – ventilation speed; · – air distribution;

The system normally operates in auto- matic mode but you can alter the stand- ard settings used by the system (air distribution, etc.). These options are explained on the following pages.
The displayed temperature values show a comfort level.
When starting the engine, increas- ing or decreasing the value dis- played will not allow the com- fort level to be reached any more quickly. The system will always op- timise the temperature increase or decrease (the ventilation system does not start instantly at maximum speed: it gradually increases). This may take several minutes.
Automatic mode is the recom- mended mode of use
In most cases, the automatic cli- mate control system ensures a com- fortable temperature in the passen- ger compartment, while maintaining good visibility and optimising fuel consumption.
The types of adjustments that can be made are described in the follow- ing pages.
Generally speaking, unless there is a particular reason not to, the dash- board air vents should remain open.
Return to automatic mode as soon as possible.

ô

The air flow is directed towards all the air vents and the pas- senger footwells. F
The air flow is directed mainly towards the footwells.
The air flow is directed to the windscreen demisting vents. ÷
There are five possible combinations for air distribution, which may be se- lected by pressing buttons 6 and 8 re- peatedly. The arrows on display 4 indi- cate the setting selected:
The air flow is directed to the windscreen demisting vents and the passenger footwells.
The manual air distribution option causes the operating tell-tale light on display 5 to go out (automatic mode), but only air distribution is no longer controlled automatically by the system.
Press button 4 to return to auto- matic mode.

Rear screen and/or door mirror de-icing/demisting.
Press button 12; indicator light 13 comes on.
This function allows electric demisting of the rear screen and/or the electric heated door mirrors, depending on the vehicle.
To exit this function, press button 12 again. Demisting automatically stops by default.
Varying the ventilation speed
In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level.
In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
Exit automatic mode by pressing but- tons 6 and 8.
Exit automatic mode by pressing button 3: AUTO goes out on display 5 and AC OFF lights up.
These buttons allow you to increase or decrease ventilation speed.
In automatic mode, depending on the outside air conditions, the ven- tilation may not start immediately at maximum power but will increase progressively until the engine tem- perature is warm enough to heat the passenger compartment air. This may take from a few seconds to several minutes.

Pressing button 14 activates air recir- culation (the symbol lights up on the display).
During recirculation, air is taken from the passenger compartment and is re- cycled, with no air being taken from out- side the vehicle.
Air recirculation allows the external at- mosphere to be cut off (when driving in polluted areas, etc.).
Press button 12 if you do not wish to switch on the heated rear screen and/ or heated door mirrors.
Press button 1; indicator lights 2 and 13 come on.
AUTO goes out on display 5.
This function rapidly demists/de-ices the windscreen, the front side windows and the door mirrors.
To exit this function, press:
Prolonged use of the air recircula- tion mode may cause the windows to mist up or lead to odours, as the air is not renewed.
It imposes automatic operation of the air conditioning and heating of the rear screen and/or heated door mirrors, and inhibits air recirculation.
– button 1 again;
– or button 4 (AUTO lights up on dis-
play 5).
We therefore advise you to return to normal mode (external air) as soon as the air recirculation function is no longer required, by pressing button 14 again.


Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours).
There is a risk of damage or of fire.
As a general rule, contact your ap- proved Dealer in the event of an op- erating fault.
You will normally notice an increase in fuel consumption (especially when driving in town) when the air conditioning is operating. For vehi- cles fitted with manual air condition- ing, switch off the system when it is not required.
– Reduction in de-icing, demist-
ing or air conditioning per- formance. This may be caused by the passenger compartment filter cartridge becoming clogged.
– No cold air is being produced.
Advice for reducing consumption and therefore helping to preserve the environment:
Check that the controls are set correctly and that the fuses are sound. Otherwise, switch off the system.
Drive with the air vents open and the windows closed.
If the vehicle has been parked in the sun, open the doors for a few moments to let the hot air escape before starting the engine.
Refer to the Maintenance Document for your vehicle for the inspection frequency.
Presence of water under the ve- hicle. After prolonged use of the air conditioning system, it is normal for water to be present under the vehi- cle. This is caused by condensation.
Do not open the refriger- ant fluid circuit. The fluid may damage eyes or skin.
Operating faults · Fuel consumption · Maintenance


With the ignition switched on, press the switch for the relevant window upwards to raise it to the desired height.
Window fails to close and/or battery disconnected
The system has to be reinitialised:
Press the switch for the window con- cerned downwards to lower it to the de- sired height.
With the door closed and the ignition switched on,
– Raise the window fully and keep the
button pressed for 2 seconds after it has stopped moving. – Lower the window fully and keep the

button pressed for 2 seconds after it has stopped moving.
Never leave your vehicle with the key or remote con- trol inside and never leave a child (or a pet) unsupervised, even for a short while. The reason for this is that the child may endanger him- self or others by starting the engine and activating equipment such as the window winders or the sunroof. If any part of the body becomes trapped, reverse the direction of the window immediately by pressing the relevant switch.
If necessary, contact an authorised dealer.
If the window closes or opens jerk- ily, the system is faulty.
1 for the driver’s side;
2 for the front passenger side.
Press the button to close the window as many times as necessary and contact an authorised dealer.
(lowering the window only)
Press switch 1 or 2 down briefly: the window will open completely.
Risk of serious injury.
Pressing the switch again while the window is moving will stop its move- ment.
Avoid resting any objects against a half-open window: there is a risk that the electric window winder could be damaged.
Driver’s responsibility



The light comes on when the luggage compartment is opened.
Automatic operation of interior lighting (depending on the vehi- cle)
Sun visor
Tilt switch 1 to move it to the position for:
Lower sun visor 2.
– if the doors are unlocked using
the remote control, the interior lights are switched on for approx- imately 15 seconds;
– continuous lighting; – intermittent lighting, which comes on
when a door is opened. It goes out when the doors concerned are prop- erly closed; – immediate switching off.
– if the doors are locked using the
remote control, the lights are switched off immediately;
– if the door is open (or not properly
closed), the lights are switched on for a period of approximately 15 minutes;
– if all the doors are closed, the in-
terior lights start to dim when the ignition is switched on.
Unlocking the vehicle or opening the doors switches on the timed courtesy lights.



Door pockets 1 These can be used to hold cups or the ashtray.

When turning corners, accelerating or braking, ensure that the recepta- cle being held by the cup holder is not dislodged.
Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passen- gers during sudden turning, braking or in the event of an accident.
Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
There is a risk of burning if hot liquid escapes.



Rear storage compartment 4
To access the storage compartment, move the seat forwards and tilt the seatback forwards.
Pull handle 3 to open it.
This compartment can be used to hold a pencil.
Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passen- gers during sudden turning, braking or in the event of an accident.
Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.




Accessories socket 2 or 3 (depending on vehicle)
This is a removable ashtray that can be fitted into the door storage compart- ments.
It is provided for connecting acces- sories approved by the Technical Department with a maximum power of 120 Watts (voltage 12 V).
To open, lift the cover.
To empty it, pull the assembly. The ash- tray will come out of its housing.
Connect accessories with a maximum power of 120 Watts only.
If your vehicle does not have an ashtray, you can purchase one from an approved dealer.
Fire hazard.



Storage under the carpet (depending on vehicle)
Press button 1 and lift the tailgate.
To open, lift luggage compartment carpet A.
Lower the luggage compartment lid.
The luggage compartment lid can only be opened if the rotating hard roof is locked.
To open · To close


The fitting of roof bars is prohibited on this vehicle.

Always position the objects transported so that the largest surface is against the partition.
Hooks 2 located on either side of the luggage compartment allow the load to be secured.
Always position the heavi- est items directly on the floor. Use the lashing points on the luggage compart- ment floor, if these are fitted to the vehicle. The luggage should be loaded in such a way that no items will be thrown forward and strike the occupants if the driver has to brake suddenly.

Reinforcement bars 1 must not be removed.

Audio system The presence and location of the equip- ment described below depends on the vehicle version. 1 Radio; 2 Steering column control; 3 Microphone.


Hands-free telephone integrated control On equipped vehicles, use micro- phone 3 and steering column control 2.

To use this equipment, consult the instructions for the equipment which should be kept with the other vehi- cle documentation.
We remind you of the need to conform to the legislation in force concerning the use of such equipment.
Using the telephone

Bonnet 4.2 Engine oil level: 4.4 general information 4.4 topping up/filling 4.5 Engine oil change 4.6 Levels: 4.7 engine coolant 4.7 brake fluid 4.8 windscreen washer reservoir 4.9 Filters 4.9 Tyre pressure 4.10 Battery 4.11 Bodywork maintenance 4.12 Interior trim maintenance 4.14



To open, pull handle 1.
To open, push tab 2 to the left as you open the bonnet.
The engine may be hot when carrying out opera- tions in close proximity. In addition, the engine cooling fan can come on at any moment. Risk of injury.
In the event of even a slight impact involving the radia- tor grille or bonnet, have the bonnet lock checked by an approved Dealer as soon as pos- sible.


Closing the bonnet Before closing the bonnet, make sure that nothing has been left in the engine compartment. To close the bonnet, replace stay 5 in holder 4. Hold the middle of the bonnet and guide it down to 20 cm above the closed position, then release. It will latch automatically under its own weight.
Opening the bonnet Lift the bonnet and release stay 5 from its holder 4. For your own safety, it is very important to fix the stay into re- tainer 3 in the bonnet.

After carrying out any work in the engine compart- ment, check that nothing has been left behind (cloth, tools, etc.). These may damage the engine or cause a fire.
Ensure that the bonnet is properly locked.
Check that nothing is pre- venting the catch from lock- ing (gravel, cloth, etc.).

It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes.

A
However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels.
A
Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
Reading the level using the dipstick – engine switched off; – remove the dipstick (refer to the fol-
The oil level should only be read with the dipstick as explained above.
If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
lowing pages for its location) and wipe it with a clean lint-free cloth; – push in the dipstick as far as it will
In order to prevent splashing, it is recommended that a funnel be used when topping up/filling the oil.
go; – take out the dipstick again; – read the level: it should never fall
below minimum mark A or exceed maximum mark B.
The engine may be hot when working in close prox- imity. In addition, the engine cooling fan may start at any moment.
Under no circumstances should maximum filling level B be exceeded: this could damage the engine and the catalytic converter.
Once the level has been read, push the dipstick in as far as it will go.
Risk of injury.



– Unscrew cap 1; – top up the level (as a guide, the ca-
The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day).
pacity between the minimum and maximum reading on dipstick 2 is between 1.5 and 2 litres, depending on the engine); – wait for approximately 10 minutes to
Engine oil grade Refer to the Maintenance Service Booklet for your vehicle.
allow the oil to flow into the engine; – check the level using dipstick 2 (as
described above). Once the level has been read, push the dipstick in as far as it will go.
Do not exceed the max level and do not forget to refit cap 1 and dip- stick 2.

Service interval: refer to the Maintenance Service Booklet for your vehicle.
Average capacities for oil change (in- cluding oil filter for information). 1.2 TCE engine: 4.2 litres 1.6 16V engine : 4.7 litres

Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes onto hot engine components.
Refer to the Maintenance Service Booklet for your vehicle.


When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position.
The engine may be hot when carrying out opera- tions in close proximity. In addition, the engine cooling fan can come on at any moment.
Risk of injury.
Risk of injury.

Engine oil change: if you are changing the oil when the engine is hot, be careful not to scald yourself if the oil overflows.
Never run the engine in an enclosed space as exhaust gases are poisonous. Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels.
Engine oil grade


Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant).
If the level needs to be topped up, only use products approved by our Technical Department which ensure:
– protection against freezing;
– anticorrosion protection of the cool-
ing system.
Refer to the Maintenance Document for your vehicle.
With the engine switched off and on level ground, the level when cold must be between the “MINI” and “MAXI” marks on coolant reservoir 1.

The engine may be hot when working in close prox- imity. In addition, the engine cooling fan may start at any moment.
Top this level up when cold before it reaches the MIN mark.
Risk of injury.
No operations should be carried out on the cooling circuit when the engine is hot.
When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position.
Consult your approved dealer at once if you notice an abnormal or repeated drop in any of the fluid levels.
Risk of burns.
Risk of injury.
Checking intervals · Replacement intervals


It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MIN” warn- ing line.
After any operation on the hydraulic cir- cuit, a specialist must replace the fluid.
Only use fluids approved by our Technical Department (and taken from a sealed container).
If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from our network or from the manufacturer’s website.
Refer to the Maintenance Document for your vehicle.
This should be checked frequently, and immediately if you notice even the slightest loss in braking efficiency.
The level should be read with the engine switched off and on level ground.
When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position.
The engine may be hot when working in close prox- imity. In addition, the engine cooling fan may start at any moment.
Risk of injury.
Risk of injury.
Level 2 · Topping up · Replacement intervals


Screen wash product (product with antifreeze in winter).
The filter elements (air filter, passenger compartment filter, etc.) should be re- placed during the maintenance opera- tions carried out on your vehicle.
Use a tool such as a needle to adjust the height of the windscreen washer jets.
Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle.
With the engine switched off, open cap 3, fill until you can see the fluid, then refit the cap.
When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position.
The engine may be hot when working in close prox- imity. In addition, the engine cooling fan may start at any moment.
Risk of injury.
Risk of injury.
Liquid · Jets · Topping up



F: rear tyre pressure.
G: tyre pressure for the emergency spare wheel.
H: maximum intended driving speed for the emergency spare wheel.
F
I: emergency spare wheel dimensions.
E
F
A
D
Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (100 kph) and the tyre pressure in- creased by 0.2 bar. Please refer to the information on “Weights” in Section 6.
F
B
E F
G D
H
Label A
B: dimension of the tyres fitted to the vehicle.
Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains.
Open the driver’s door to read it.
C: intended driving speed.
Tyre pressures should be checked when the tyres are cold.
D: recommended pressure for optimis- ing fuel consumption. Note: driving comfort may be altered.
If the tyre pressures cannot be checked when the tyres are cold, increase the pressures from 0.2 to 0.3 bar (or 3 PSI). Never deflate a hot tyre.
E: front tyre pressure.

When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle. Tyres fitted to the vehicle should either be identical to those fitted originally or conform to those recommended by your approved dealer.


Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “CHARGE BATTERY” is displayed on the instrument panel. In this case, start the engine. The charge status of your battery can decrease especially if you use your vehicle:

– for short journeys;
– for driving in town;
– when the temperature drops;
– after extended use of consumers
(radio etc.) with the engine switched off.
Label A Observe the indications on the battery: – 2 naked flames and smoking forbid-
Battery 1 does not require any mainte- nance.
As this operation is complex, we advise you to contact an approved Dealer.
den; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials.

Handle the battery with care as it contains sulphuric acid, which must not come into contact with eyes or skin. If it does, wash the affected area with plenty of cold water. If necessary, consult a doctor.
The engine may be hot during operations in close proximity. In addition, the engine cooling fan may start at any moment.
Ensure that naked flames, red hot objects and sparks do not come into contact with the battery as there is a risk of explosion.
The battery is a specific type, please ensure it is replaced with the same type. Consult an approved dealer.
Risk of injury.
Replacing the battery

A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle reg- ularly.
Allow dirt to accumulate on the exterior.
Allow rust to form following minor im- pacts.
Clean the rotating rotating hard roof using a high pressure washer and make sure you carefully wash the rotat- ing hard roof seals; risk of leaks.
Do not use solvents not approved by our Technical Department to remove stains as this could damage the paint- work.
Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences.
Use a high pressure washer less than one metre from the vehicle to wash under the rotating hard roof cover: risk of damage to the opening/closing mechanism.
Do not drive in snow or muddy condi- tions without washing the vehicle, par- ticularly under the wheel arches and body.
Corrosive agents in the atmosphere – atmospheric pollution (built-up and
industrial areas), – saline atmospheres (near the sea,
Do not degrease or clean mechani- cal components (e.g. the engine com- partment), underneath the body, parts with hinges (e.g. inside the doors) and painted plastic external fittings (e.g. bumpers) using high-pressure clean- ing equipment or by spraying on prod- ucts not approved by our Technical Department. Doing this could give rise to corrosion or operational faults.
particularly in hot weather), – seasonal and damp weather condi-
tions, (e.g. road salt in winter, water from road cleaners, etc.).
Abrasive action Dust and sand in the air, mud, road grit thrown up by other vehicles, etc.
Wash the vehicle in bright sunlight or freezing temperatures.
You should take a number of minor pre- cautions in order to safeguard your ve- hicle against such risks.
Do not scrape off mud or dirt without pre-wetting.
Minor impacts

You should Wash your car frequently, with the engine off, with cleaning products rec- ommended by the manufacturer (never use abrasive products). Rinse thor- oughly beforehand with a jet: – spots of tree resin and industrial
Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- hicle on a public highway).
Return the windscreen wiper stalk to the Park position (refer to the informa- tion on the “Windscreen washer, wiper” in Section 1). Check the mounting of external accessories, additional lights and mirrors, and ensure that the wiper blades are secured with adhesive tape. Remove the radio aerial mast if your vehicle is fitted with this equipment. Remember to remove the tape and refit the antenna after washing.
Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage.
Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading.
grime; – mud in the wheel arches and under-
neath the body which forms damp patches; – bird droppings, which cause a
Remember to visit the body shop pe- riodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Document.
chemical reaction with the paint that rapidly discolours paintwork and may even cause the paint to peel off; wash the vehicle immediately to remove these marks since it is im- possible to remove them by polish- ing; – salt, particularly in the wheel arches
If it is necessary to clean mechani- cal components, hinges, etc., spray them with products approved by our Technical Department to protect them after they have been cleaned.
As the headlights are made of plastic “glass”, use a soft cloth or cotton wool to clean them. If this does not clean them properly, moisten the cloth with soapy water, then wipe clean with a soft damp cloth or cotton wool. Finally, carefully dry off with a soft dry cloth.
and underneath the body after driv- ing in areas where the roads have been gritted.
Cleaning products containing alco- hol must not be used.
Remove any plant matter (resin, leaves, etc.) from the vehicle regularly.
Clean the roof cover using a soft cloth.
We have selected special products to care for your vehicle and you can obtain these from the manufactur- er’s accessory outlets.

A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regu- larly.
Glass instrument panel (e.g. instrument panel, clock, exterior temperature display, radio display, etc.)
Vacuum-clean the textiles regularly.
Use a soft cloth (or cotton wool). If this does not clean it properly, use a soft cloth (or cotton wool) slightly mois- tened with soapy water and then wipe clean with a soft damp cloth or cotton wool. Finally, carefully dry off with a soft dry cloth.
A stain should always be dealt with swiftly.
Use soapy water.
Dab lightly (never rub) with a soft cloth, rinse and remove the excess.
Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap.
Solid or pasty stain
Detergents (washing-up liquid, pow- dered products, alcohol-based prod- ucts) should not be used.
Carefully remove the excess solid or pasty material immediately with a spatula (working from the edges to the centre to avoid spreading the stain). Clean as for a liquid stain.
Cleaning products containing alco- hol must not be used under any cir- cumstances.
Use a soft cloth.
Rinse and soak up the excess.
Special instructions for sweets or chewing gum
These must be kept clean. Use products selected by our Technical Department (Approved outlets) or warm, soapy water and a sponge and wipe with a dry cloth. Detergents or dyes must not be used under any circumstances.
Put an ice cube on the stain to solidify it, then proceed as for a solid stain.
For further recommendations for maintaining the interior, and/or for any unsatisfactory results, please see an authorised dealer.
Liquid stain

You should not:
You are strongly advised not to po- sition objects such as deodorants, scents, etc. near air vents, as this could damage your dashboard trim.
If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv- er’s mat should be fitted on the driver’s side, etc.) and fit them with the compo- nents supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
With the vehicle stationary, ensure that nothing will impede driving (anything obstructing the pedals, heel wedged by the mat, etc.).

You are strongly recom- mended not to use high- pressure or spray cleaning equipment inside the pas- senger compartment: use of such equipment could impair the correct functioning of the electrical or elec- tronic components in the vehicle, or have other detrimental effects.



Puncture 5.2 Emergency spare wheel 5.2 Tyre inflation kit 5.3 Tool kit (jack, wheelbrace, etc.) 5.6 Wheel trim 5.6 Changing a wheel 5.7 Tyres (tyre and wheel safety, use in winter) 5.9 Rear lights (changing bulbs) 5.14 Indicator lights (changing bulbs) 5.15 Interior lights (changing bulbs) 5.17 Fuses 5.19 Battery 5.22 Key, radio frequency remote control: battery 5.24 Accessories 5.25 Wipers (replacing blades) 5.26 Towing 5.27 Operating faults 5.28


If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use.
In the event of a puncture, depending on the vehicle, you will have:
Vehicles fitted with an emergency spare wheel which is different to the four other wheels:
An emergency spare wheel or tyre in- flation kit (refer to the information on the following pages).
– Never fit more than one emergency spare wheel to the same vehicle.
– Replace the emergency spare wheel as soon as possible with a wheel identi-
cal to the original one.
– When this is fitted to the vehicle, which must only be a temporary measure, the
driving speed must not exceed the speed indicated on the label on the wheel.
This is located in the luggage compart- ment. To access it: – open the luggage compartment lid; – lift luggage compartment carpet A; – unscrew the central mounting; – remove the emergency spare wheel.
– Fitting an emergency spare wheel may alter the way the vehicle usually runs.
Avoid sudden acceleration or deceleration and reduce your speed when cor- nering.
– If you need to use snow chains, fit the emergency spare wheel to the rear axle
and check the tyre pressure.




Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture.
The kit is only approved for inflating the tyres of the ve- hicle originally equipped with the kit.
You should therefore carefully check the condition of the tyre sidewalls before any operation.
It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
Driving with underinflated, flat or punctured tyres can be dangerous and may make the tyre impossible to repair.
Avoid spillage on skin when han- dling the repair liquid bottle. If drop- lets do leak out, rinse them off with plenty of water.
This repair is temporary
Keep the repair kit away from chil- dren.
A tyre which has been punctured should always be inspected (and re- paired, where possible) as soon as possible by a specialist.

Do not dispose of the empty bottle in the countryside. Return it to your approved dealer or to a recycling or- ganisation.
The kit repairs tyres when tread A has been dam- aged by objects smaller than 4 mm. It cannot repair all types of puncture, such as cuts larger than 4 mm, or cuts in tyre sidewall B.
When taking a tyre which has been repaired using this kit to be replaced, you must inform the specialist.
The bottle has a limited service life which is indicated on its label. Check the expiry date.
When driving, vibration may be felt due to the presence of the repair product injected into the tyre.
Ensure also that the wheel rim is in good condition.
Contact an approved dealer to re- place the inflation tube and repair product bottle.
Do not pull out the foreign body causing the puncture if it is still in the tyre.


With the engine running and the parking brake applied,
– after a maximum of 15 minutes, stop
inflating and read the pressure (on pressure gauge 5).
– unroll the hose from the container;
– connect the compressor hose 3 to
the container’s inlet 8;
– depending on the vehicle, connect
the container 8 to the compressor from the container recess 7;
– unscrew the valve cap on the rel-
it, continue inflation with the kit; to reduce it, press button 6.
evant wheel and screw on the con- tainer’s inflation adapter 1;
If a minimum pressure of 1.8 bar is not reached after 15 minutes, repair is not possible; do not drive the ve- hicle but contact an approved dealer.
– adapter 2 must be connected to the
– press switch 4 to inflate the tyre to
Depending on the vehicle, in the event of a puncture, use the kit located in the boot or underneath the luggage com- partment carpet.
the recommended pressure (please refer to the information in the section on “Tyre pressure”);
If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle’s presence with a warning triangle or with other devices as per the legislation apply- ing to the country you are in.
Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic.
vehicle accessories socket;

– Affix the driving recommendation
label to the dashboard where it can easily be seen by the driver;
The kit should not be operated for more than 15 consecutive minutes.
– Put the kit away.
– At the end of this initial inflation op-

eration, air will still escape from the tyre. You must drive a short distance in order to seal the hole.
Please be aware that a poorly tightened or miss- ing valve cap can make the tyres less airtight and may lead to pressure loss.
– Start immediately and drive at be-
tween 12 and 40 mph (20 and 60 km/h) in order to distribute the product evenly in the tyre and, after driving for 2 miles (3 km), stop and check the pressure.
Always use valve caps identical to those fitted originally and tighten them fully.
– If the pressure is greater than 1.3 bar
Once the tyre is correctly inflated, remove the kit: slowly unscrew the in- flation adapter 1 to prevent any repair product from escaping and store the container in plastic packaging to pre- vent the product from escaping.
but less than the recommended pressure (refer to the label affixed to the edge of the driver’s door), read- just it. Otherwise, please contact an authorised dealer: the tyre cannot be repaired.

Following repair with the kit, do not travel further than 120 miles (200 km). In addi- tion, reduce your speed and under no circumstances exceed 48 mph (80 km/h). The sticker, which you must affix in a prominent position on the dashboard, reminds you of this. Depending on the country or local legislation, a tyre repaired with the inflation kit may need to be replaced.
Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.


This is used to tighten or release the wheel bolts.
Towing hitch 2 Refer to the information on “Towing” in Section 5.
Jack 3 When replacing the jack, fold it cor- rectly and position the wheelbrace cor- rectly before replacing it in its position.
Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then position it correctly in its housing: there is a risk of injury.
Hubcap tool 4 This tool is used to remove the wheel trims.
The tool kit is located in the luggage compartment: lift the luggage compart- ment carpet then unscrew the central mounting.
The tools included in the tool kit depend on the vehicle.
If wheel bolts are supplied in the tool kit, only use these bolts for the emergency spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances should it be used for carrying out repairs underneath the vehicle or to gain access to the un- derside of the vehicle.
Wheelbrace 1


Offer up jack 2 horizontally; the jack head must be lined up with sill 3 as close as possible to the wheel con- cerned.
If necessary, remove the wheel trim.
Start cranking the jack up by hand to align the base plate (which should be pushed slightly under the vehicle).
Use wheelbrace 1 to slacken off the wheel bolts. Fit it so that you press downwards rather than pulling up- wards.
Turn the wheelbrace until the wheel lifts off the ground.
If the vehicle is not equipped with a jack or wheelbrace, you can obtain these from your approved dealer.
Switch on the hazard warn- ing lights.
Keep the vehicle away from traffic and on a level sur- face where it will not slip (if neces- sary, place a solid support under the jack base).
If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle’s presence with a warning triangle or with other devices as per the legislation apply- ing to the country you are in.
Apply the parking brake and engage a gear (first or reverse). Ask all the passengers to leave the vehicle and keep them away from traffic.
To prevent any risk of injury or damage to the vehicle, only crank the jack until the wheel you are replacing is a maximum of 3 centimetres off the ground.

Undo the bolts and take off the wheel.
Fit the emergency spare wheel onto the hub and rotate it until the mount- ing holes in the wheel are aligned with those of the hub.
If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and lower the jack.
With the wheel on the ground, tighten the bolts fully and have the tightness of the bolts checked (tightening torque: 105 N.m) and the emergency spare wheel pressure checked as soon as possible.
If you have a puncture, re- place the wheel as soon as possible. A tyre which has been punc- tured should always be inspected (and repaired, where possible) by a specialist.


When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
The tyres are the only contact between the vehicle and the road, so it is essen- tial to keep them in good condition.
You must make sure that your tyres conform to local road traffic regulations.
An overloaded vehicle, long journeys by motorway, particularly in very hot weather, or continual driving on poorly surfaced minor roads will lead to more rapid tyre wear and affect safety.
The tyres must be in good condition and the tread form must have sufficient depth; tyres approved by our techni- cal department have tread wear indica- tors 1 which are indicators moulded into the tread at several points.
When they need to be re- placed, only tyres of the same make, size, type and profile should be used.
Incidents which occur when driving, such as striking the kerb, may damage the tyres and wheel rims, and could also lead to misalignment of the front or rear axle geometry. In this case, have the condition of these checked by an approved dealer.
Tyres fitted to the vehicle should either be identical to those fitted originally or conform to those recommended by your approved dealer.

Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label af- fixed to the edge of the driver’s door).
Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey.

For safety reasons, this op- eration must be carried out by a specialist.
If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.2 to 0.3 bar (or 3 PSI).
Fitting different tyres may change your vehicle as follows:
Never deflate a hot tyre.
– it may mean that your vehicle no
longer conforms to current regu- lations;
Special note Depending on the vehicle, there may be an adapter which needs to be posi- tioned on the valve before air is added.
– It may change the way it handles
Incorrect tyre pressures lead to abnormal tyre wear and unusually hot running. These are factors which may seriously affect safety and lead to:
– It may cause the steering to be
– It may affect the use of snow
chains.
– poor road holding,
– risk of bursting or tread separa-
tion.
Please be aware that a poorly tightened or miss- ing valve cap can make the tyres less airtight and lead to pressure loss.
Refer to the information on the “Emergency spare wheel” and in- structions on “Changing a wheel” in Section 5.
The pressure depends on the load and the speed of use. Adjust the pressure according to the condi- tions of use (refer to the label affixed to the edge of the driver’s door).
Always use valve caps identical to those fitted originally and tighten them fully.
when cornering; · heavy;

For safety reasons, fitting snow chains to the rear axle is strictly for- bidden.
In all cases, we would recommend that you contact an approved dealer who will be able to advise you on the choice of equipment which is most suitable for your vehicle.
Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle.
Snow or Winter tyres
We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhe- sion.

Chains may only be fitted to tyres of the same size as those originally fitted to your vehicle.
Chains may be fitted, provided that they are specific chains. We would advise you to consult an approved Dealer.
This type of equipment may only be used for a limited period and as laid down by local legislation. It is neces- sary to observe the speed specified by current legislation.
Special notes on versions fitted with 17” wheels: they cannot be fitted with snow chains.
If you wish to use special equip- ment, consult an approved dealer.
These tyres must, at a minimum, be fitted to the two front wheels.
Chains · Studded tyres



A
To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an ap- proved dealer.
Side light
Pull bulb holder 6. Change the bulb.
Remove cover A or B, disconnect bulb 3 or 4, unlock spring 2 or 5 to remove the bulb.
Bulb type: W5W.

The bulbs are under pres- sure and can break when replaced.
Do not touch the bulb glass. Hold it by its base. When the bulb has been changed, make sure you refit the cover correctly.
Rotate bulb holder 1 to unlock it.
Risk of injury.
Bulb type: PY21W.
Bulb type: H1.
The engine may be hot when carrying out opera- tions in close proximity. In addition, the engine cooling fan can come on at any moment.
It is essential to use anti U.V. 55W bulbs so as not to damage the plastic on the headlights.
Risk of injury.



To comply with current legislation, or as a precaution, you can obtain an emergency kit from an approved dealer containing a set of spare bulbs and fuses.
For refitting, proceed in the reverse order to removal.
Ensure that the bulb is correctly se- cured and reposition the cover.
– Unclip the cover;
– turn bulb 8 a quarter of a turn and
Any operation on (or modi- fication to) the electrical system must be performed by an approved dealer since incorrect connections could damage the electrical equipment (wiring, components, in particu- lar the alternator). In addition, your dealer has available all the parts necessary for fitting electrical com- ponents.
– disconnect the bulb and change it.
Do not touch the bulb glass. Hold it by its base. When the bulb has been changed, make sure you refit the cover correctly.
Bulb type: H11 55W.
Changing a bulb · remove it;




Undo screws 1.
Unclip and detach the rear light cluster from the outside.
3 Side light and fog light Bulb type: P 21/4W.
Remove plastic cover A.
Undo screw 2.
Undo bulb holder a quarter of a turn.
4 Side light Bulb type: P 21/4W.
Undo the bulb a quarter of a turn.
Replace the bulb.
5 Side light and brake light Bulb type: P 21/5 W.
6 Direction indicator light Bulb type: PY 21 W.
The bulbs are under pres- sure and can break when replaced.
Risk of injury.



Number plate lights 9
Consult an approved Dealer.
– Unclip light 9 by pressing tab 8;
– remove the light cover to gain access
to the bulb.
Bulb type: W5W.
The bulbs are under pres- sure and can break when replaced.
Risk of injury.



Side indicator lights 11
– Turn the bulb holder a quarter of a
Unclip indicator light 11 (using a flat- blade screwdriver or similar).
turn and take out the bulb;
– disconnect the bulb and change it.
Turn the bulb holder one quarter-turn and take out the bulb.
Bulb type: P 21 W.
Bulb type: W5W.
The bulbs are under pres- sure and can break when replaced.
Risk of injury.
Take care not to scratch the body- work.



Release bulb 2.
Unclip lens 1 in the direction indicated (using a flat-blade screwdriver or simi- lar).
Bulb type: W5W.
The bulbs are under pres- sure and can break when replaced.
Risk of injury.



Press tab 4 to release the lens and access bulb 5.
Unclip light 3 by pressing the tabs on each side (using a flat-blade screw- driver or similar).
Bulb type: W5W.
Disconnect the light.
The bulbs are under pres- sure and can break when replaced.
Risk of injury.




Clip 3
If electrical equipment does not work, check the condition of the fuses.
Remove the fuse using tweezers 3, lo- cated on the back of cover 1 or in glove box 2.
Depending on the vehicle, remove flap 1 or the flap located in storage compartment 2.
To remove the fuse from the tweezers, slide the fuse to the side.

Check the fuse in question and replace it, if neces- sary, by a fuse of the same rating.
To identify the fuses, refer to the fuse allocation label (shown on the following pages).
If a fuse is fitted where the rating is too high, it may cause the electrical circuit to overheat (risk of fire) in the event of an item of equipment using an excessive amount of current.
It is not advisable to use the free fuse locations.
To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an ap- proved dealer.

Numbers Allocation Numbers Allocation Numbers Allocation
1 and 2 Windscreen wiper. 11 Direction indicator lights/ Diagnostic socket. 19 Location reserved for additional equipment.
3 Power-assisted steering. 12 Power supply/Instrument panel. 20 Front and rear fog lights.
13 Dipped beam headlights.
4 Location reserved for additional equipment.
21 Main beam headlights/ Horn. 14 Central door locking
5 Brake light/Speed limiter. 15 Side lights.
22 Location reserved for additional equipment. 6 Reversing lights/door mirror control/alarm siren. 16 Location reserved for additional equipment.
23 Electric windows.
7 Air bag.
17 Heated rear screen/Heated door mirrors.
24 Location reserved for additional equipment. 8 Passenger compartment electrical unit/transponder.
9 Injection/fuel pump. 18 Interior lighting/courtesy light/automatic climate control.
25 Dipped beam headlights/ rear fog light.
10 ABS/ASR/ESP 26 Sunroof.

Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL)
Numbers Allocation Numbers Allocation Numbers Allocation
27 Location reserved for additional equipment. 36 Location reserved for additional equipment. 43 Left-hand side light/number plate light.
28 Passenger compartment ventilation. 37 Heated door mirrors.
44 Location reserved for additional equipment.
29 Radio/Passenger compartment electrical unit. 38 Horn.
30 Accessories socket. 39 Rear fog lights. 45 Diode protection.
31 Location reserved for additional equipment. 40 Location reserved for additional equipment. 46 Location reserved for additional equipment.
32 Right-hand main beam headlight. 41 Heated seats.
47 Location reserved for additional equipment. 33 Left-hand main beam headlight.
Right-hand side light/ accessories socket/cruise control/speed limiter control/central door locking control/hazard warning lights control.
34 Right-hand dipped beam headlight.
35 Left-hand dipped beam headlight. 48 Radio.

Connecting a battery charger
– Ensure that any electrical consumers
The battery charger must be com- patible with a battery with nominal voltage of 12 volts.
(courtesy lights, etc.) are switched off before disconnecting or recon- necting the battery.
Do not disconnect the battery when the engine is running. Follow the instruc- tions given by the manufacturer of the battery charger you are using.
– When charging, stop the charger
before connecting or disconnecting the battery.
– Do not place metal objects on the
battery to avoid creating a short cir- cuit between the terminals.
– Always wait at least one minute after
the engine has been switched off before disconnecting a battery.
Handle the battery with care as it contains sulphuric acid, which must not come into contact with eyes or skin. If it does, wash the affected area with plenty of cold water. If necessary, consult a doctor.
– Make sure that you reconnect the
battery terminals after refitting.
Ensure that naked flames, red hot objects and sparks do not come into contact with the battery as there is a risk of explosion.
Special procedures may be required to charge some batteries. Contact your ap- proved dealer.
The engine may be hot when car- rying out operations in close prox- imity. In addition, the engine cooling fan can come on at any moment.
Avoid all risk of sparks which may cause an immediate explosion, and charge the battery in a well-venti- lated area. Risk of serious injury.
Risk of injury.



If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
The two batteries must have an iden- tical nominal voltage of 12 volts. The battery supplying the current should have a capacity (amp-hours, Ah) which is at least the same as that of the dis- charged battery.
Ensure that there is no risk of contact between the two vehicles (risk of short circuiting when the positive terminals are connected) and that the discharged battery is properly connected. Switch off your vehicle ignition.
Attach positive lead A to mounting 1 attached to (+) terminal 2 then to (+) terminal 3 of the battery supplying the current.
Attach the negative lead B to the (– ) terminal 4 of the battery supplying the current, then to the (–) terminal 5 of the discharged battery.
Start the engine of the vehicle supply- ing the current and run it at a moderate speed.
Check that there is no con- tact between leads A and B and that the positive lead A is not touching any metal parts on the vehicle supplying the current.
Start the engine. As soon as it is run- ning, disconnect leads A and B in the reverse order ( 5 - 4 - 3 - 2 ).
Risk of injury and/or damage to the vehicle.




Key, remote controls
Special feature of key A
Remove screw 3.

Open the case at slot 1 using a coin, and replace battery 2, observing the polarity shown on the back of the cover.
When refitting, ensure that the cover is correctly clipped on and the screw tightened.
Do not dispose of your used batteries in the countryside. Give them to an organisa- tion that collects and recy- cles used batteries.
Batteries can be obtained from your approved Dealer.
These batteries should have a serv- ice life of approximately two years.
Replacing the battery



Before fitting an electrical or electronic device (particu- larly for transmitters/receiv- ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.
If you are using an anti-theft device, only attach it to the brake pedal.
Contact an approved dealer for this information.

Electrical and electronic accessories
– Connect accessories with a maximum power of 120 Watts only.
Fire hazard.

Use of transmission/ receiving devices (telephones, CB equipment etc.).
– No work may be carried out on

the vehicle’s electrical or radio circuits, except by approved Dealers: an incorrectly con- nected system may result in damage being caused to the electrical equipment and/or the components connected to it;
Fitting after-market accessories If you wish to install acces- sories on the vehicle: con- sult an approved dealer. Also, to ensure the correct opera- tion of your vehicle, and to avoid any risk to your safety, we recom- mend that you use only specific ac- cessories, designed for your vehi- cle, which are the only accessories for which the manufacturer will pro- vide a warranty.
Telephones and CB equipment with integrated aerials may cause inter- ference to the original electronic systems fitted to the vehicle: it is ad- visable only to use equipment with an external aerial.
– if the vehicle is fitted with any
aftermarket electrical equip- ment, make sure that the unit is correctly protected by a fuse. Establish the rating and position of this fuse.
Furthermore, we remind you of the need to comply with the legis- lation in force concerning the use of such equipment.


To refit the wiper blade, proceed in re- verse order to removal.
Make sure that the blade is correctly locked in position.
– In frosty weather, make sure that the wiper blades are not stuck by ice (to avoid the risk of the motor overheating).
– Lift the windscreen wiper arm 3 as
far as it will go (the arm does not lift up completely);
– press button 2 and slide the wiper
Check the condition of the wiper blades. You are responsible for their service life:
– Check the condition of the wiper
blades. Replace the wiper blades as soon as they begin to lose efficiency (approximately once a year).
blade sideways to release hook 4 on the wiper arm.
– clean the blades and the wind-
screen regularly with soapy water;
Whilst changing the blade, take care not to drop the arm onto the window after it has been removed as this may break the window.
– do not use them when the wind-
– free them from the windscreen
when they have not been used for a long time.
screen is dry;

The steering wheel must be un- locked and the ignition key must be in position M (ignition on) to provide brake lights and hazard warning lights on the towed vehicle. At night the vehicle must have its lights on.


You must observe the towing regu- lations which apply in the country in which you are driving.
Contact an approved dealer.
– At the front, towing hitch 3 (lo-
cated in the tool kit).
– At the rear, towing point 5.
These towing points may only be used for pulling the vehicle, never for lifting it either directly or indirectly.
Unclip cover 2.
Tighten towing hitch 3 fully: first by hand until it stops then finish by locking it with wheelbrace 4.

Do not push the vehicle if the steering column is locked.
Towing hitch 3 and wheelbrace 4 are located in the tool kit.
– The towing hitch must only be used for towing your vehicle.
Do not remove the key from the ignition when the vehi- cle is being towed.
When the engine is stopped, steering and brak- ing assistance are not op- erational.
– It is forbidden to tow other vehicles.

The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible.
The starter is activated POSSIBLE CAUSES WHAT TO DO
There is no response, the warning lights fail to light up and the starter does not turn.
Battery lead disconnected or terminals corroded.
Check battery terminals: scrape and clean if oxidised and retighten.
Discharged battery. Connect another battery to the faulty battery.
Battery unserviceable. Replace battery.
Battery terminals not correctly tightened, oxidised.
Check battery terminals: scrape and clean if oxidised and retighten.
Discharged battery. Connect another battery to the faulty battery.
It is difficult to start the engine in wet weather or after washing the vehicle.
Poor ignition, ignition system damp. Dry the spark plug and coil wires.
The engine is difficult to start when hot. Faulty carburation (bubbles of vaporised fuel in the circuit).
Let the engine cool down.
Poor compression. Consult an approved dealer.

The starter is activated POSSIBLE CAUSES WHAT TO DO
The engine splutters but does start or starts with difficulty when cold.
Incorrect starting procedure. or Poor fuel supply or ignition fault.
Refer to the section entitled “Starting/ stopping the engine”. If the vehicle will not start, do not keep trying to start it. Consult an approved dealer.
Fuel supply cut-off system activated if vehicle has been subjected to severe impact.
Consult an approved dealer.
Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged.
Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer.
Smoke under the bonnet. Short circuit or cooling system leak. Stop, switch off the ignition, stand away from the vehicle and contact an approved Dealer.

On the road POSSIBLE CAUSES WHAT TO DO
The oil pressure warning light comes on:
– while turning or braking The level is too low. Top up the engine oil (refer to the information on the Engine oil level, topping up/refilling in Section 4).
– at idle speed Low oil pressure. Consult the nearest approved Dealer.
– is slow to go out or remains lit on ac-
Loss of oil pressure. Stop the vehicle and contact an approved Dealer.
celeration.
Loss of engine power. Clogged air filter. Replace the filter.
Fuel supply fault. Check the fuel level.
Faulty spark plugs, incorrect electrode gaps.
Consult an approved dealer.
Unstable idle speed or the engine stalls. Poor compression (spark plugs, ignition, air leak).
Consult an approved dealer.

On the road POSSIBLE CAUSES WHAT TO DO
Steering becomes heavy. Assistance overheating. Leave to cool.
Faulty power-assisted steering. Consult an approved dealer.
The engine overheats. The coolant temperature warning light comes on (or the indicator needle is in the red area).
Coolant pump: belt stretched or broken. Engine cooling fan not working.
Stop the vehicle, switch off the engine and contact an approved Dealer.
Coolant leaks. Check the condition of hoses and the tightness of the clips. Check the expansion bottle: it should contain coolant. If it does not, top it up (once it has cooled). Take care not to scald yourself. This action is only temporary; consult your approved Dealer as soon as possible.

Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved by our Technical Department may be used for this purpose.

Electrical equipment POSSIBLE CAUSES WHAT TO DO
The wipers do not work. Wiper blades stuck. Free the blades before using the wipers.
Faulty electrical circuit. Consult an approved dealer.
The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
Direction indicators flashing more quickly.
Bulb blown. Refer to the information on “Headlights: changing bulbs” or “Rear and side lights: changing bulbs” in Section 5.
The direction indicators do not work. Faulty electrical circuit. Consult an approved dealer.
The headlights do not switch on or off. Faulty electrical circuit or control. Consult an approved dealer.
Traces of condensation in the lights. This is not a fault. The presence of traces of condensation in lights is a natural phenomenon linked to variations in temperature. These traces soon disappear when the lights are switched on.

Rotating hard roof POSSIBLE CAUSES WHAT TO DO
The luggage compartment lid will not open
Rotating hard roof not locked. Lock the rotating hard roof; refer to the information on the “Rotating hard roof: opening/closing” in Section 3.
The roof will not open or close. Roof opening conditions not fulfilled. Apply the opening conditions (refer to the information on the “Rotating hard roof” in Section 3).
Roof fault.
Leave the roof closed or close it using the methods described in “Rotating hard roof: operating fault” in Section 3 and consult your approved dealer.
Electrical fault (discharged battery, etc.).
The roof and the cover have been left in the intermediate position for too long.
Finish the cycle manually and use the method described in the paragraph “Rotating hard roof: operating fault” in Section 3, if required.

Rotating hard roof POSSIBLE CAUSES WHAT TO DO
The message “ROOF: READ HANDBOOK” appears.
Roof opening fault. Lock the roof then unlock it without lifting it.
Exterior temperature too low (below - 10°C). The system does not open, to prevent damage.
Roof in thermal protection mode (too many successive operations).
Allow the system to cool for a few minutes before using it again.
The message “CHECK ROOF” ap- pears continually or when the roof’s open/close switch is pressed.
Roof fault. Consult an approved dealer.

Vehicle identification plates 6.2 Dimensions 6.4 Engine specifications 6.5 Weights 6.6 Towing weights 6.6 Replacement parts and repairs 6.7 Service sheets 6.8 Anti-corrosion check 6.14



A
The information shown on the ve- hicle identification plate should be quoted on all correspondence or orders.
4 MAM (Maximum Authorised Mass)
for front axle. 5 GTW (Gross train weight: vehicle
fully loaded, with trailer). 6 MPAW (Maximim Permissible

The presence and location of the in- formation depends on the vehicle.
Weight) for front axle. 7 MPAW on rear axle. 8 Reserved for related or additional
Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval
entries. 9 Diesel exhaust emissions. 10 Paint reference (colour code).
number. 3 Identification number.
Depending on the vehicle, this information is also given on marking B.



A
Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.



0,795 2,368 0,665 1,456

Versions 1.2 Tce 1.6 16V
Engine type (see engine plate) D4Ft K4M
Cubic capacity (cc) 1,149 1,598
It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel:
Type of fuel Octane Rating
– with an octane rating of 91 for a label showing 95 or 98; – with an octane rating of 87 for a label showing 91, 95 or 98.
Only use the spark plugs specified for your vehicle’s engine. The type should be marked on a label affixed inside the engine compartment. If it is not then contact your approved dealer. Fitting spark plugs which are not to specification may damage the engine.
Spark plugs

The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Maximum permissible all-up weight (MMAC) Total train weight (MTR)
Weights are indicated on the vehicle identification plate (refer to
the information on “Vehicle identification plates” in Section 6)
Braked trailer weight Prohibited
Unbraked trailer weight Prohibited
Permissible nose weight Prohibited
Maximum permissible load on roof Prohibited
Maximum permissible load on the tailgate Prohibited

Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.

VIN:

□
Anticorrosion check:
OK □ Not OK* □
□ Anticorrosion check:
OK □ Not OK* □
□
Anticorrosion check:
OK □ Not OK* □

VIN:
□
Anticorrosion check:
OK □ Not OK* □
□ Anticorrosion check:
OK □ Not OK* □
□
Anticorrosion check:
OK □ Not OK* □

VIN:
□
Anticorrosion check:
OK □ Not OK* □
□ Anticorrosion check:
OK □ Not OK* □
□
Anticorrosion check:
OK □ Not OK* □

VIN:
□
Anticorrosion check:
OK □ Not OK* □
□ Anticorrosion check:
OK □ Not OK* □
□
Anticorrosion check:
OK □ Not OK* □

VIN:

□
Anticorrosion check:
OK □ Not OK* □
□ Anticorrosion check:
OK □ Not OK* □
□
Anticorrosion check:
OK □ Not OK* □

VIN:
□
Anticorrosion check:
OK □ Not OK* □
□ Anticorrosion check:
OK □ Not OK* □
□
Anticorrosion check:
OK □ Not OK* □

If the continuation of the warranty is subject to repair, it is indicated below.
VIN:

Corrosion repair operation to be carried out:
Date of repair:
Date of repair:
Date of repair:
Stamp

If the continuation of the warranty is subject to repair, it is indicated below.
VIN:
Corrosion repair operation to be carried out:
Date of repair:
Date of repair:
Date of repair:
Stamp

If the continuation of the warranty is subject to repair, it is indicated below.
VIN:
Corrosion repair operation to be carried out:
Date of repair:
Date of repair:
Date of repair:
Stamp

If the continuation of the warranty is subject to repair, it is indicated below.
VIN:
Corrosion repair operation to be carried out:
Date of repair:
Date of repair:
Date of repair:
Stamp

If the continuation of the warranty is subject to repair, it is indicated below.
VIN:
Corrosion repair operation to be carried out:
Date of repair:
Date of repair:
Date of repair:
Stamp

A ABS 1.35, 2.10 → 2.12 accessories 5.25 accessories socket 3.23 additional methods of restraint 1.15 → 1.17, 1.19
changing gear 2.5 child restraint/seat 1.20 – 1.21, 1.23 → 1.26 child safety 1.2 – 1.3, 1.20 – 1.21, 1.23 → 1.26, 3.19 child seats 1.20 – 1.21, 1.23 → 1.26 children 1.2 – 1.3, 1.6 – 1.7, 1.20 – 1.21 children (safety) 3.19 cigar lighter 3.23 cleaning:
side protection 1.18 to the front seat belts 1.15 → 1.17 adjusting your driving position 1.12 air bag 1.15 → 1.19, 1.35 air conditioning 3.8 → 3.18 air vents 3.6 – 3.7 anti-corrosion check 6.14 → 6.18 anti-corrosion protection 4.12 – 4.13 anti-lock braking system: ABS 2.10 → 2.12 antipollution
inside the vehicle 4.14 – 4.15 outside the vehicle 4.12 – 4.13 clock 1.49 closing the doors 1.6 – 1.7 control instruments 1.34 → 1.40 controls 1.30 → 1.33 coolant 1.38, 4.7 courtesy light 3.20, 5.17 – 5.18 courtesy mirrors 3.20 cruise control 2.13 → 2.19 cruise control-speed limiter 2.13 → 2.19
advice 2.6 → 2.8 armrest:
front 3.22 ashtray 3.23 ASR (traction control) 2.10 → 2.12 audible and visual signals 1.51
D dashboard 1.30 → 1.33 daytime running lights 1.52 demisting
B batteries 5.24 battery 4.11
rear screen 3.9 dimensions 6.4 display 1.34 → 1.39 doors 1.6 – 1.7, 1.10 doors/tailgate 1.6 – 1.7, 1.10 driver’s position 1.30 → 1.37 driving 2.2, 2.4 → 2.8, 2.10 → 2.19 driving position
troubleshooting 5.22 – 5.23 bonnet 4.2 – 4.3 brake fluid 4.8 bulbs
changing 5.14 → 5.16
C catalytic converter 2.4 central door locking 1.5, 1.10 changing a bulb 5.14 → 5.16 changing a wheel 5.7 – 5.8
settings 1.12 → 1.14
E electric windows 3.19

Electronic Stability Program: ESP 2.10 → 2.12 emergency brake assist 2.10 → 2.12 emergency braking 2.10 → 2.12 emergency spare wheel 5.2, 5.6 engine oil 4.4 → 4.6 engine oil capacity 4.5 – 4.6 engine oil level 4.4 → 4.6 environment 2.9 ESP: Electronic Stability Program 2.10 → 2.12 external temperature 1.49
G gear lever 2.5
H handbrake 1.34, 2.5 hands-free telephone integrated control 3.26 hazard warning lights signal 1.51 – 1.52 headlight flashers 1.51 heating and air conditioning system 3.18 heating system 3.8 → 3.18 horn 1.51 horn:
flash 1.51 sounding the horn 1.51 hubcap tool 5.6
operating faults 5.28 → 5.34 filter
air filter 2.6, 4.9 diesel filter 2.6, 4.9 oil filter 4.6, 4.9 passenger compartment filter 4.9 fittings 3.21 – 3.22 front seat adjustment 1.11 front seats
I ignition switch 2.2 indicators 1.34, 1.51 indicators:
direction indicators 1.51, 5.14 exterior temperature indicator 1.49 instrument panel 1.34 → 1.40 instrument panel 1.34 → 1.40, 1.52 instrument panel messages 1.40 interior trim
adjustment 1.11 → 1.14 with manual controls 1.11 fuel
advice on fuel economy 2.6 → 2.8 capacity 1.56 filling 1.56 – 1.57 grade 1.56 – 1.57 fuel economy 2.6 → 2.8 fuel filler cap 1.56 – 1.57 fuel level 1.38 fuel tank
maintenance 4.14 – 4.15
J jack 5.6
K keys 1.2 → 1.4
capacity 1.56 – 1.57 fuel tank capacity 1.56 – 1.57 fuses 5.19 → 5.21
F faults

L levels:
methods of restraint in addition to the seat belts ...1.15 → 1.19 multimedia equipment 3.26
brake fluid 4.8 coolant 1.38, 4.7 fuel 1.38 windscreen washer reservoir 4.9 lifting the vehicle
N navigation 3.26 navigation system 3.26
O oil change 4.4 → 4.6 opening the doors 1.6 – 1.7 operating faults 1.34 → 1.37, 5.28 → 5.34
changing a wheel 5.7 – 5.8 lighting:
exterior 1.52 – 1.53 instrument panel 1.52 interior 3.20, 5.17 – 5.18 lights
mobile directional 1.53 lights:
maintenance 4.12 – 4.13 reference 6.2 power-assisted steering 1.48 practical advice 2.6 → 2.8, 5.28 → 5.34 pretensioners 1.15 puncture 5.2, 5.6 → 5.8
brake lights 5.14 dipped beam headlights 1.34, 1.52 direction indicators 1.34, 1.51, 5.14 fog lights 1.34, 5.14 hazard warning 1.51 main beam headlights 1.34, 1.53 number plate lights 5.15 reversing lights 5.14 side lights 1.52, 5.14 locking the doors 1.2 → 1.7, 1.10
R radio 3.26 rear screen
demisting 3.9 rear screen de-icing/demisting 3.15 rear view mirrors 1.50 RENAULT ANTI-INTRUDER DEVICE (RAID) 1.10 replacement parts 6.7 reverse gear
M maintenance 2.6 maintenance:
bodywork 4.12 – 4.13 interior trim 4.14 – 4.15 mechanical 4.2 – 4.3, 6.8 → 6.13 mileage before service 6.8 → 6.13 map reading lights 3.20 methods of restraint in addition to the front seat belts 1.15 → 1.17
selecting 2.5 running in 2.2
S seat belt pretensioners 1.15 → 1.17 seat belts 1.12 → 1.19
P paintwork

see-me-home lighting 1.53 service sheets 6.8 → 6.13 side indicator lights
traction control: ASR 2.10 → 2.12 transporting children 1.20 – 1.21, 1.23 → 1.26 transporting objects
changing bulbs 5.15 side protection devices 1.18 signals and lights 1.52 – 1.53 special features of petrol vehicles 2.4 speed limiter 2.13 → 2.15 starting the engine 2.3 steering wheel
in the luggage compartment 3.25 trims 5.6 trip computer and warning system 1.34 → 1.37, 1.40 tyre inflation kit 5.3 → 5.5 tyre pressure 4.10, 5.10 tyre pressures 4.10 tyres 2.8, 4.10, 5.9 → 5.11
adjustment 1.48 storage compartment 3.21 – 3.22 storage compartments 3.21 – 3.22 sun visor 3.20 sunroof 3.19
V variable power-assisted steering 1.35 vehicle identification 6.2 – 6.3 vehicle identification plates 6.2 – 6.3 ventilation 3.8 → 3.18
T tailgate 3.24 tanks and reservoirs
W warning buzzer 1.6, 1.51, 1.53 warning lights 1.34 → 1.37, 1.40 washing 4.12 – 4.13 weights 6.6 wheelbrace 5.6 wheels (safety) 5.9 → 5.11 windscreen de-icing/demisting 3.15 windscreen washer 1.54 – 1.55, 4.9 windscreen washer/wiper 1.54 – 1.55 wiper blades 5.26 wipers 1.54 – 1.55
brake fluid 4.8 coolant 4.7 tanks and reservoirs:
windscreen washer 4.9 technical specifications 6.2 → 6.4, 6.6 – 6.7 telephone 3.26 temperature regulation 3.12 → 3.18 tool kit 5.6 towing
breakdown 5.27 towing equipment 3.25 towing a caravan 3.25, 6.6 towing equipment
blades 5.26
fitting 3.25 towing hitch 5.27 towing rings 1.21, 1.23, 3.25 towing weights 6.6







à999102219Ròíîä 52 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60 NU 865-6 – 99 91 022 19R – 11/2012 – Edition anglaise
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.