EN
Progress logo
Official user manual

Progress PK1803

56 pages·1.7 MB·Refrigeration and freezing·PDF·ENDEFRITJA
Progress PK1803
Table of Contents 47 sections CONTENTS · SAFETY INFORMATION · Children and vulnerable people safety · General Safety · … ShowHide
Page 2 of the Progress PK1803 user manual — Electrical connection
Page 2 · click to enlarge
Page 2
  • Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
  • Do not damage the refrigerant circuit.
  • Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
  • Do not use water spray and steam to clean the appliance.
  • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.
  • Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

SAFETY INSTRUCTIONS

Installation

  • Do not install this appliance in areas that are too humid or too colds, such as the construction appendices, garages or wine cellars.
  • When you move the appliance, lift it by the front edge to avoid scratching the floor.
  • Remove all the packaging.
  • Do not install or use a damaged appliance.
  • Obey the installation instruction supplied with the appliance.
  • Always be careful when you move the appliance because it is heavy. Always wear safety gloves.
  • Make sure the air can circulate around the appliance.
  • Wait at least 4 hours before connecting the appliance to the power supply. This is to allow the oil to flow back in the compressor.
  • Do not install the appliance close to radiators or cookers, oven or hobs.
  • The rear of the appliance must stand against the wall.
  • Do not install the appliance where there is direct sunlight.

Electrical connection

  • The appliance must be earthed.
  • All electrical connections should be made by a qualified electrician.
  • Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact an electrician.
  • Always use a correctly installed shockproof socket.
  • Do not use multi-plug adapters and extension cables.
  • Make sure not to cause damage to the electrical components (e.g. mains plug, mains cable, compressor). Contact the
Page 3 of the Progress PK1803 user manual — Disposal
Page 3 · click to enlarge
Page 3
  • Service or an electrician to change the electrical components.
  • The mains cable must stay below the level of the mains plug.
  • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
  • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.

Care and cleaning

  • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
  • This appliance contains hydrocarbons in the cooling unit. Only a qualified person must do the maintenance and the recharging of the unit.
  • Regularly examine the drain of the appliance and if necessary, clean it. If the drain is blocked, defrosted water collects in the bottom of the appliance.

Use

  • Do not change the specification of this appliance.
  • Do not put electrical appliances (e.g. ice cream makers) in the appliance unless they are stated applicable by the manufacturer.
  • Be careful not to cause damage to the refrigerant circuit. It contains isobutane (R600a), a natural gas with a high level of environmental compatibility. This gas is flammable.
  • If damage occurs to the refrigerant circuit, make sure that there are no flames and sources of ignition in the room. Ventilate the room.
  • Do not let hot items to touch the plastic parts of the appliance.
  • Do not store flammable gas and liquid in the appliance.
  • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
  • Do not touch the compressor or the condenser. They are hot.

Disposal

  • Disconnect the appliance from the mains supply.
  • Cut off the mains cable and discard it.
  • Remove the door to prevent children and pets to be closed inside of the appliance.
  • The refrigerant circuit and the insulation materials of this appliance are ozonefriendly.
  • The insulation foam contains flammable gas. Contact your municipal authority for information on how to discard the appliance correctly.
  • Do not cause damage to the part of the cooling unit that is near the heat exchanger.
Page 4 of the Progress PK1803 user manual — Temperature regulation
Page 4 · click to enlarge
Page 4

OPERATION

Control panel

3 4 5 6

1 ON/OFF button 2 Display 3 Temperature warmer button 4 Temperature colder button

5 OK button 6 Functions button

A) Timer function B) Fan function C) Intensive cooling function D) DrinksChill function E) Holiday function F) ChildLock function G) Alarm indicator H) Temperature indicator

A H E F G C B D

Switching on

Switching off

Connect the mains plug to the power socket

1. Press the appliance ON/OFF button for 5 seconds. The display switches off. 2. Disconnect the mains plug from the power socket.
1. Press the ON/OFF if the display is off. The temperature indicator shows the set default temperature. 2. The alarm buzzer may sound after a few seconds. If "DEMO" appears on the display, the appliance is in demonstration mode. Refer to "Troubleshooting...".

Temperature regulation

The default set temperature for the fridge is +5°C.

Set the temperature of the fridge by pressing the temperature button. The temperature indicator shows the set temperature.

To select a different set temperature refer to "Temperature regulation".

Functions · Display

Page 5 of the Progress PK1803 user manual — ChildLock function
Page 5 · click to enlarge
Page 5
1. Press Functions button until the corresponding icon appears. The ChildLock indicator flashes. 2. Press OK to confirm. The ChildLock indicator is shown. 3. To switch off the function press Functionsbutton until ChildLock indicator flashes, then press OKto confirm. The ChildLock indicator goes off.

The set temperature will be reached within 24 hours. After a power failure the set temperature remains stored.

DrinksChill function

The DrinksChill mode is to be used to set an acoustic alarm at the preferred time, useful, for example, when you want to rapidly chill food products for a certain length of time.

IntensiveCooling

1. To switch on the function press Functions button until the corresponding icon appears. The DrinksChill indicator flashes. The timer shows the set value (30 minutes) for a few seconds. 2. Press the temperature colder button or temperature warmer button to change the Timer set value from 1 to 90 minutes. 3. Press OK to confirm. DrinkChill indicator is shown. The Timer starts to flash (min). At the end of the countdown the DrinksChill indicator flashes and an audible alarm sounds. 4. Press OK to switch off the sound and terminate the function.

If you need to insert a large amount of warm food, for example after doing the grocery shopping, we suggest activating the IntensiveCooling to chill the products more rapidly and to avoid warming the other food which is already in the refrigerator.

The IntensiveCooling shuts off automatically after approximately 6 hours.

1. To switch on the function: a. Press Functions until the

corresponding icon appears. The IntensiveCooling indicator flashes.

b. Press OK to confirm. The IntensiveCooling indicator is shown. 2. To switch off the function before its automatic end:

a. Press Functions until the

It is possible to deactivate the function at any time during the countdown by pressing Functions until DrinksChill indicator flashes and then pressing OK to confirm.

IntensiveCooling indicator flashes. b. Press OK to confirm. The IntensiveCooling indicator goes off.

The function switches off by selecting a different fridge set temperature.

Holiday function

It is possible to change the time during the countdown and at the end by pressing the temperature colder button and the temperature warmer button.

This function allows you to keep the refrigerator closed and empty during a long holiday period without the formation of bad odours.

The fridge compartment must be empty with holiday function on.

ChildLock function

To lock any possible operation through the buttons select the ChildLock function.

1. Press Functions until the corresponding icon appears.
Page 6 of the Progress PK1803 user manual — Fan
Page 6 · click to enlarge
Page 6

The Holiday indicator flashes. The fridge temperature indicator shows the set temperature. 2. PressOK to confirm. The Holiday indicator is shown. To switch off the function repeat the procedure until the Holiday indicator goes off.

Door open alarm

An acoustic alarm will sound if the door is left open for a few minutes. The door open alarm conditions are indicated by:

  • a flashing alarm indicator;
  • an acoustic buzzer. When normal conditions are restored (door closed), the alarm will stop.

The function switches off by selecting a different fridge set temperature.

During the alarm phase, the buzzer can be switched off by pressing any control panel button.

DAILY USE

Movable shelves

The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

2. Reposition the shelf as required.

Do not move the glass shelf above the vegetable drawer and the bottle shelf to ensure correct air circulation.

Fan

Positioning the door shelves

To permit storage of food packages of various sizes, the door shelves can be placed at different heights.

To make these adjustments proceed as follows:

The refrigerator compartment is equipped with a device that allows for rapid cooling of foods and more uniform temperature in the compartment.

1. Gradually pull the shelf in the direction of the arrows until it comes free.

This device activates by itself when needed, for example for a quick temperature recovering after door opening or when the ambient temperature is high.

Page 7 of the Progress PK1803 user manual — General warnings
Page 7 · click to enlarge
Page 7

It is possible to switch on the device manually when needed (refer to "Fan Function").

The fan device stops when the door is open and restarts immediately after the door closing.

HINTS AND TIPS

Normal operating sounds

  • do not store warm food or evaporating liquids in the refrigerator
  • do cover or wrap the food, particularly if it has a strong flavour
  • position food so that air can circulate freely around it

The following sounds are normal during operation:

  • A faint gurgling and bubbling sound from coils sound when refrigerant is pumped.
  • A whirring and pulsating sound from the compressor when refrigerant is pumped.
  • A sudden cracking noise from inside appliance caused by thermic dilatation (a natural and not dangerous physical phenomenon).
  • A faint click noise from the temperature regulator when the compressor switches on or off.

Hints for refrigeration

Useful hints:

  • Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable drawer.
  • For safety, store in this way only one or two days at the most.
  • Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.
  • Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
  • Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible.
  • Bottles: these need a cap and should be stored on the door bottle shelf, or (if equipped) on the bottle rack.
  • Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.

Hints for energy saving

  • Do not open the door frequently or leave it open longer than absolutely necessary.
  • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.

Hints for fresh food refrigeration

To obtain the best performance:

CARE AND CLEANING

General warnings

Page 8 of the Progress PK1803 user manual — TROUBLESHOOTING
Page 8 · click to enlarge
Page 8

every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.

This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.

It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside.

The accessories and parts of the appliance are not suitable for washing in a dishwasher.

Periodic cleaning

The equipment has to be cleaned regularly:

Periods of non-operation

When the appliance is not in use for long periods, take the following precautions:

1. Clean the inside and accessories with lukewarm water and some neutral soap. 2. Regularly check the door seals and wipe clean to ensure they are clean and free from debris. 3. Rinse and dry thoroughly. 4. If accessible, clean the condenser and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption.
1. Disconnect the appliance from electricity supply. 2. Remove all food. 3. Clean the appliance and all accessories. 4. Leave the door/doors open to prevent unpleasant smells.

Defrosting of the refrigerator

Frost is automatically eliminated from the evaporator of the refrigerator compartment

TROUBLESHOOTING

Page 9 of the Progress PK1803 user manual — What to do if...
Page 9 · click to enlarge
Page 9

What to do if...

Problem Possible cause Solution

The appliance does not oper- ate.

The appliance is switched off.

Switch on the appliance.

The mains plug is not con- nected to the mains socket correctly.

Connect the mains plug to the mains socket correctly.

There is no voltage in the mains socket.

Connect a different electrical appliance to the mains socket. Contact a qualified electrician.

The appliance is noisy. The appliance is not sup- ported properly.

Check if the appliance stands stable.

Audible or visual alarm is on. The cabinet has been re- cently switched on or the temperature is still too high.

Refer to "Door Open Alarm"or "High Temperature Alarm".

The temperature in the ap- pliance is too high.

Refer to "Door Open Alarm"or "High Temperature Alarm".

The door is left open. Close the door.

The temperature in the ap- pliance is too high.

Contact a qualified electrician or contact the nearest Author- ized Service Centre.

A rectangular symbol is shown instead of numbers on the Temperature Display.

Temperature sensor prob- lem.

Contact the nearest Authorized Service Centre (the cooling sys- tem will continue to keep food products cold, but temperature adjustment will not be possi- ble).

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp does not work. The lamp is defective. Contact the nearest Authorized Service Centre.

The compressor operates continually.

Temperature is set incor- rectly.

Refer to "Operation" chapter.

Many food products were put in at the same time.

Wait some hours and then check the temperature again.

The room temperature is too high.

Refer to climate class chart on the rating plate.

Food products placed in the appliance were too warm.

Allow food products to cool to room temperature before stor- ing.

Page 10 of the Progress PK1803 user manual — What to do if...
Page 10 · click to enlarge
Page 10

Problem Possible cause Solution

The door is not closed cor- rectly.

Refer to "Closing the door".

The IntensiveCooling func- tion is switched on.

Refer to "IntensiveCooling func- tion".

The compressor does not start immediately after press- ing the IntensiveCooling, or after changing the tempera- ture.

This is normal, no error has occurred.

The compressor starts after a period of time.

Water flows inside the refrig- erator.

The water outlet is clog- ged.

Clean the water outlet.

Food products prevent that water flows into the water collector.

Make sure that food products do not touch the rear plate.

Water flows on the floor. The melting water outlet is not connected to the evap- orative tray above the com- pressor.

Attach the melting water outlet to the evaporative tray.

Temperature cannot be set. The FastFreeze or Intensi- veCooling function is switched on.

Switch off FastFreeze or Inten- siveCooling manually, or wait until the function resets auto- matically to set the tempera- ture. Refer to "FastFreeze or In- tensiveCooling function".

DEMO appears on the dis- play.

The appliance is in demon- stration mode.

Keep the OK pressed for ap- proximately 10 seconds until a long sound is heard and display shuts off for a short time.

The temperature in the appli- ance is too low/too high.

The temperature regulator is not set correctly.

Set a higher/lower temperature.

The door is not closed cor- rectly.

Refer to "Closing the door".

The food products' tem- perature is too high.

Let the food products tempera- ture decrease to room temper- ature before storage.

Many food products are stored at the same time.

Store less food products at the same time.

The door has been opened often.

Open the door only if necessa- ry.

Page 11 of the Progress PK1803 user manual — Electrical connection
Page 11 · click to enlarge
Page 11

Problem Possible cause Solution

The IntensiveCooling func- tion is switched on.

Refer to "IntensiveCooling func- tion".

There is no cold air circula- tion in the appliance.

Make sure that there is cold air circulation in the appliance.

Closing the door

If the advice does not lead to the desired result, call the nearest brand-mark service.

1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the After Sales Service.

Replacing the lamp

The appliance is equipped with a longlife LED interior light.

Only service is allowed to replace the lighting device. Contact your After Sales Service.

INSTALLATION

Positioning

Some functional problems might occur for some types of models when operating outside of that range. The correct operation can only be guaranteed within the specified temperature range. If you have any doubts regarding where to install the appliance, please turn to the vendor, to our customer service or to the nearest Service Centre

This appliance can be installed in a dry, well ventilated indoor where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

SN +10°C to + 32°C

Electrical connection

N +16°C to + 32°C

ST +16°C to + 38°C

  • Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply.
  • The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician.

T +16°C to + 43°C

Cli- mate class · Ambient temperature

Page 12 of the Progress PK1803 user manual — Door reversibility
Page 12 · click to enlarge
Page 12
  • The manufacturer declines all responsibility if the above safety precautions are not observed.
  • This appliance complies with the E.E.C. Directives.
Progress PK1803 — Ventilation requirements diagram (page 12)
Fig. 1 · Ventilation requirements

Ventilation requirements

The airflow behind the appliance must be sufficient.

Progress PK1803 — Ventilation requirements diagram (page 12)
Fig. 2 · Ventilation requirements
6. Install the spacer. 7. Install the door. 8. Tighten the upper pin.

Installing the appliance

1. If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure.
Progress PK1803 — Installing the appliance diagram (page 12)
Fig. 3 · Installing the appliance

Door reversibility

The door of the appliance opens to the right. If you want to open the door to the left, follow these steps before you install the appliance:

1. Loosen and remove the upper pin.
Progress PK1803 — Door reversibility diagram (page 12)
Fig. 4 · Door reversibility
2. Drill the unit using a Ø 2.5 mm drill (10 mm max. penetration). 3. Fix the square fitting to the appliance.
2. Remove the door. 3. Remove the spacer. 4. With a key, loosen the lower pin. 5. Tighten the lower pin on the opposite side.
Page 13 of the Progress PK1803 user manual — Ventilation requirements
Page 13 · click to enlarge
Page 13
Progress PK1803 — Ventilation requirements diagram (page 13)
Fig. 5 · Ventilation requirements
8. Open the door. Put the lower hinge cover in position.
Progress PK1803 — Ventilation requirements diagram (page 13)
Fig. 6 · Ventilation requirements
9. Attach the appliance to the niche with 4 screws.
4. Install the appliance in the niche. 5. Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture.
Progress PK1803 — Ventilation requirements diagram (page 13)
Fig. 7 · Ventilation requirements
Progress PK1803 — Ventilation requirements diagram (page 13)
Fig. 8 · Ventilation requirements
10. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case.
6. Push the appliance in the direction of the arrows (2) against the cupboard on the opposite side of the hinge. 7. Adjust the appliance in the niche. Make sure that the distance between the appliance and the cupboard frontedge is 44 mm. The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Make sure that the clearance between the appliance and the cupboard is 4 mm.
Page 14 of the Progress PK1803 user manual — Ventilation requirements
Page 14 · click to enlarge
Page 14
Progress PK1803 — Ventilation requirements diagram (page 14)
Fig. 9 · Ventilation requirements
Progress PK1803 — Ventilation requirements diagram (page 14)
Fig. 10 · Ventilation requirements
16. Push the part (Hc) on the part (Ha).
11. Attach the covers (C, D) to the lugs and the hinge holes.
Progress PK1803 — Ventilation requirements diagram (page 14)
Fig. 11 · Ventilation requirements
17. Open the appliance door and the kitchen furniture door at an angle of 90°. 18. Insert the small square (Hb) into guide (Ha). 19. Put together the appliance door and the furniture door and mark the holes.
12. Install the vent grille (B). 13. Attach the hinge covers (E) to the hinge. 14. Disconnect the parts (Ha), (Hb), (Hc) and (Hd).
Progress PK1803 — Ventilation requirements diagram (page 14)
Fig. 12 · Ventilation requirements
15. Install the part (Ha) on the inner side of the kitchen furniture.
Page 15 of the Progress PK1803 user manual — Technical data
Page 15 · click to enlarge
Page 15
Progress PK1803 — TECHNICAL INFORMATION diagram (page 15)
Fig. 13
23. Press the part (Hd) on the part (Hb).
Progress PK1803 — TECHNICAL INFORMATION diagram (page 15)
Fig. 14
20. Remove the small squares and drill holes with ø 2 mm at 8 mm from the outer edge of the door. 21. Place the small square on the guide again and fix it with the screws supplied. 22. Align the kitchen furniture door and the appliance door by adjusting the part (Hb).

Do a final check to make sure that:

  • All screws are tightened.
  • The sealing strip is attached tightly to the cabinet.
  • The door opens and closes correctly.
Progress PK1803 — TECHNICAL INFORMATION diagram (page 15)
Fig. 15

TECHNICAL INFORMATION

Technical data

Progress PK1803 — Technical data diagram (page 15)
Fig. 16 · Technical data
Page 16 of the Progress PK1803 user manual — NOISES
Page 16 · click to enlarge
Page 16

The technical information are situated in the rating plate, on the external or internal side of the appliance and in the energy label.

NOISES

There are some sounds during normal running (compressor, refrigerant circulation).

Progress PK1803 — NOISES diagram (page 16)
Fig. 17
Page 17 of the Progress PK1803 user manual — ENVIRONMENT CONCERNS
Page 17 · click to enlarge
Page 17
Progress PK1803 — NOISES diagram (page 17)
Fig. 18

ENVIRONMENT CONCERNS

Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not

dispose appliances marked with the symbol

with the household waste. Return the product to your local recycling facility or contact your municipal office.

*

Page 18 of the Progress PK1803 user manual — NOISES
Page 18 · click to enlarge
Page 18
Page 18 of the Progress PK1803 user manual — NOISES
Page 19 of the Progress PK1803 user manual — NOISES
Page 19 · click to enlarge
Page 19
Page 19 of the Progress PK1803 user manual — NOISES
Page 20 of the Progress PK1803 user manual — NOISES
Page 20 · click to enlarge
Page 20
Page 20 of the Progress PK1803 user manual — NOISES
Page 21 of the Progress PK1803 user manual — www.progress-hausgeraete.de
Page 21 · click to enlarge
Page 21

www.progress-hausgeraete.de

222370491-A-342014

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The appliance does not oper- ate.The appliance is switched off.Switch on the appliance. p.9
The appliance does not oper- ate.The mains plug is not con- nected to the mains socket correctly.Connect the mains plug to the mains socket correctly. p.9
The appliance does not oper- ate.There is no voltage in the mains socket.Connect a different electrical appliance to the mains socket. Contact a qualified electrician. p.9
The appliance is noisy.The appliance is not sup- ported properly.Check if the appliance stands stable. p.9
Audible or visual alarm is on.The cabinet has been re- cently switched on or the temperature is still too high.Refer to "Door Open Alarm"or "High Temperature Alarm". p.9
Audible or visual alarm is on.The temperature in the ap- pliance is too high.Refer to "Door Open Alarm"or "High Temperature Alarm". p.9
Audible or visual alarm is on.The door is left open.Close the door. p.9
Audible or visual alarm is on.The temperature in the ap- pliance is too high.Contact a qualified electrician or contact the nearest Author- ized Service Centre. p.9
A rectangular symbol is shown instead of numbers on the Temperature Display.Temperature sensor prob- lem.Contact the nearest Authorized Service Centre (the cooling sys- tem will continue to keep food products cold, but temperature adjustment will not be possi- ble). p.9
The lamp does not work.The lamp is in stand-by.Close and open the door. p.9
The lamp does not work.The lamp is defective.Contact the nearest Authorized Service Centre. p.9
The compressor operates continually.Temperature is set incor- rectly.Refer to "Operation" chapter. p.9
The compressor operates continually.Many food products were put in at the same time.Wait some hours and then check the temperature again. p.9
The compressor operates continually.The room temperature is too high.Refer to climate class chart on the rating plate. p.9
The compressor operates continually.Food products placed in the appliance were too warm.Allow food products to cool to room temperature before stor- ing. p.9
The door is not closed cor- rectly.Refer to "Closing the door". p.10
The IntensiveCooling func- tion is switched on.Refer to "IntensiveCooling func- tion". p.10
The compressor does not start immediately after press- ing the IntensiveCooling, or after changing the tempera- ture.This is normal, no error has occurred.The compressor starts after a period of time. p.10
Water flows inside the refrig- erator.The water outlet is clog- ged.Clean the water outlet. p.10
Water flows inside the refrig- erator.Food products prevent that water flows into the water collector.Make sure that food products do not touch the rear plate. p.10
Water flows on the floor.The melting water outlet is not connected to the evap- orative tray above the com- pressor.Attach the melting water outlet to the evaporative tray. p.10
Temperature cannot be set.The FastFreeze or Intensi- veCooling function is switched on.Switch off FastFreeze or Inten- siveCooling manually, or wait until the function resets auto- matically to set the tempera- ture. Refer to "FastFreeze or In- tensiveCooling function". p.10
DEMO appears on the dis- play.The appliance is in demon- stration mode.Keep the OK pressed for ap- proximately 10 seconds until a long sound is heard and display shuts off for a short time. p.10
The temperature in the appli- ance is too low/too high.The temperature regulator is not set correctly.Set a higher/lower temperature. p.10
The temperature in the appli- ance is too low/too high.The door is not closed cor- rectly.Refer to "Closing the door". p.10
The temperature in the appli- ance is too low/too high.The food products' tem- perature is too high.Let the food products tempera- ture decrease to room temper- ature before storage. p.10
The temperature in the appli- ance is too low/too high.Many food products are stored at the same time.Store less food products at the same time. p.10
The temperature in the appli- ance is too low/too high.The door has been opened often.Open the door only if necessa- ry. p.10
There is no cold air circula- tion in the appliance.Make sure that there is cold air circulation in the appliance. p.11

Ask about the Progress PK1803

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Progress PK1803

Be the first to ask — other owners or our team will answer.

Original document

Progress PK1803 manual PDF

56 pages·1.7 MB·Refrigeration and freezing·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…