EN
Progress logo
Official user manual

Progress PK1203

48 pages·1.2 MB·Refrigeration and freezing·PDF·ENITJA
Progress PK1203
Table of Contents 41 sections CONTENTS · SAFETY INFORMATION · Children and vulnerable people safety · General Safety · … ShowHide
Page 2 of the Progress PK1203 user manual — Electrical connection
Page 2 · click to enlarge
Page 2
  • Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
  • Do not damage the refrigerant circuit.
  • Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
  • Do not use water spray and steam to clean the appliance.
  • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.
  • Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.

SAFETY INSTRUCTIONS

Installation

  • Do not install this appliance in areas that are too humid or too colds, such as the construction appendices, garages or wine cellars.
  • When you move the appliance, lift it by the front edge to avoid scratching the floor.
  • Remove all the packaging.
  • Do not install or use a damaged appliance.
  • Obey the installation instruction supplied with the appliance.
  • Always be careful when you move the appliance because it is heavy. Always wear safety gloves.
  • Make sure the air can circulate around the appliance.
  • Wait at least 4 hours before connecting the appliance to the power supply. This is to allow the oil to flow back in the compressor.
  • Do not install the appliance close to radiators or cookers, oven or hobs.
  • The rear of the appliance must stand against the wall.
  • Do not install the appliance where there is direct sunlight.

Electrical connection

  • The appliance must be earthed.
  • Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact an electrician.
  • Always use a correctly installed shockproof socket.
  • Do not use multi-plug adapters and extension cables.
  • Make sure not to cause damage to the electrical components (e.g. mains plug, mains cable, compressor). Contact the Authorised Service Centre or an
Page 3 of the Progress PK1203 user manual — Switching on
Page 3 · click to enlarge
Page 3
  • electrician to change the electrical components.
  • The mains cable must stay below the level of the mains plug.
  • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
  • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.

Care and cleaning

  • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
  • This appliance contains hydrocarbons in the cooling unit. Only a qualified person must do the maintenance and the recharging of the unit.
  • Regularly examine the drain of the appliance and if necessary, clean it. If the drain is blocked, defrosted water collects in the bottom of the appliance.

Use

  • Do not change the specification of this appliance.
  • Do not put electrical appliances (e.g. ice cream makers) in the appliance unless they are stated applicable by the manufacturer.
  • Be careful not to cause damage to the refrigerant circuit. It contains isobutane (R600a), a natural gas with a high level of environmental compatibility. This gas is flammable.
  • If damage occurs to the refrigerant circuit, make sure that there are no flames and sources of ignition in the room. Ventilate the room.
  • Do not let hot items to touch the plastic parts of the appliance.
  • Do not store flammable gas and liquid in the appliance.
  • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
  • Do not touch the compressor or the condenser. They are hot.

Disposal

  • Disconnect the appliance from the mains supply.
  • Cut off the mains cable and discard it.
  • Remove the door to prevent children and pets to be closed inside of the appliance.
  • The refrigerant circuit and the insulation materials of this appliance are ozonefriendly.
  • The insulation foam contains flammable gas. Contact your municipal authority for information on how to discard the appliance correctly.
  • Do not cause damage to the part of the cooling unit that is near the heat exchanger.

Internal light

  • The type of lamp used for this appliance is not suitable for household room illumination

OPERATION

Switching on

2. Turn the Temperature regulator clockwise to a medium setting.
1. Insert the plug into the wall socket.
Page 4 of the Progress PK1203 user manual — Movable shelves
Page 4 · click to enlarge
Page 4

Switching off

1. Turn the Temperature regulator toward lower settings to obtain the minimum coldness. 2. Turn the Temperature regulator toward higher settings to obtain the maximum coldness.

To turn off the appliance, turn the temperature regulator to the "0" position.

Temperature regulation

The temperature is regulated automatically.

  • A medium setting is generally the most suitable. However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on:
  • room temperature,
  • how often the door is opened,
  • the quantity of food stored,
  • the location of the appliance.

FIRST USE

Cleaning the interior

Before using the appliance for the first time, the interior and all internal accessories should be washed with lukewarm water and some neutral soap to remove the typical smell of a brand-new product, then dried thoroughly.

DAILY USE

Positioning the door shelves

To permit storage of food packages of various sizes, the door shelves can be placed at different heights.

1. Gradually pull the shelf in the direction of the arrows until it comes free. 2. Reposition as required.

Movable shelves

The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

Page 5 of the Progress PK1203 user manual — Hints for fresh food refrigeration
Page 5 · click to enlarge
Page 5

If “OK” is displayed (A), put fresh food into area indicated by symbol, if not (B), adjust the temperature controller to a colder setting and wait 12 hours before checking the temperature indicator again.

OK

A

Do not move the glass shelf above the vegetable drawer and the bottle shelf to ensure correct air circulation.

B

OK

After putting fresh food into the appliance or after opening the door repeatedly or for a long period, it is normal for the indicator not to show "OK"; wait at least 12 hours before readjusting the temperature controller.

Temperature indicator

For proper storage of food the refrigerator is equipped with the temperature indicator. The symbol on the side wall of the appliance indicates the coldest area in the refrigerator.

HINTS AND TIPS

Normal operating sounds

  • do cover or wrap the food, particularly if it has a strong flavour
  • position food so that air can circulate freely around it

The following sounds are normal during operation:

  • A faint gurgling and bubbling sound from coils sound when refrigerant is pumped.
  • A whirring and pulsating sound from the compressor when refrigerant is pumped.
  • A sudden cracking noise from inside appliance caused by thermic dilatation (a natural and not dangerous physical phenomenon).
  • A faint click noise from the temperature regulator when the compressor switches on or off.

Hints for refrigeration

Useful hints:

  • Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable drawer.
  • For safety, store in this way only one or two days at the most.
  • Cooked foods, cold dishes, etc. : these should be covered and may be placed on any shelf.
  • Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
  • Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible.
  • Bottles: these need a cap and should be stored on the door bottle shelf, or (if equipped) on the bottle rack.

Hints for energy saving

  • Do not open the door frequently or leave it open longer than absolutely necessary.

Hints for fresh food refrigeration

To obtain the best performance:

  • do not store warm food or evaporating liquids in the refrigerator
Page 6 of the Progress PK1203 user manual — Periods of non-operation
Page 6 · click to enlarge
Page 6
  • Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.

CARE AND CLEANING

Defrosting of the refrigerator

Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.

General warnings

This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.

It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside.

The accessories and parts of the appliance are not suitable for washing in a dishwasher.

Periodic cleaning

Periods of non-operation

When the appliance is not in use for long periods, take the following precautions:

1. Disconnect the appliance from electricity supply. 2. Remove all food. 3. Clean the appliance and all accessories. 4. Leave the door/doors open to prevent unpleasant smells.

The equipment has to be cleaned regularly:

1. Clean the inside and accessories with lukewarm water and some neutral soap. 2. Regularly check the door seals and wipe clean to ensure they are clean and free from debris. 3. Rinse and dry thoroughly. 4. If accessible, clean the condenser and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption.
Page 7 of the Progress PK1203 user manual — TROUBLESHOOTING
Page 7 · click to enlarge
Page 7

TROUBLESHOOTING

What to do if...

Problem Possible cause Solution

The appliance does not oper- ate.

The appliance is switched off.

Switch on the appliance.

The mains plug is not con- nected to the mains socket correctly.

Connect the mains plug to the mains socket correctly.

There is no voltage in the mains socket.

Connect a different electrical appliance to the mains socket. Contact a qualified electrician.

The appliance is noisy. The appliance is not sup- ported properly.

Check if the appliance stands stable.

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

The compressor operates continually.

Temperature is set incor- rectly.

Refer to "Operation" chapter.

Many food products were put in at the same time.

Wait some hours and then check the temperature again.

The room temperature is too high.

Refer to climate class chart on the rating plate.

Food products placed in the appliance were too warm.

Allow food products to cool to room temperature before stor- ing.

The door is not closed cor- rectly.

Refer to "Closing the door".

Water flows inside the refrig- erator.

The water outlet is clog- ged.

Clean the water outlet.

Food products prevent that water flows into the water collector.

Make sure that food products do not touch the rear plate.

Water flows on the floor. The melting water outlet is not connected to the evap- orative tray above the com- pressor.

Attach the melting water outlet to the evaporative tray.

Page 8 of the Progress PK1203 user manual — Closing the door
Page 8 · click to enlarge
Page 8

Problem Possible cause Solution

The temperature in the appli- ance is too low/too high.

The temperature regulator is not set correctly.

Set a higher/lower temperature.

The door is not closed cor- rectly.

Refer to "Closing the door".

The food products' tem- perature is too high.

Let the food products tempera- ture decrease to room temper- ature before storage.

Many food products are stored at the same time.

Store less food products at the same time.

The door has been opened often.

Open the door only if necessa- ry.

There is no cold air circula- tion in the appliance.

Make sure that there is cold air circulation in the appliance.

If the advice does not lead to the desired result, contact the nearest Authorised Service Centre.

2. Replace the lamp with one of the same power and shape, specifically designed for household appliances. (the maximum power is shown on the light bulb cover). 3. Reassemble the lamp cover. 4. Connect the plug to the mains socket. 5. Open the door. Make sure that the light comes on.

Replacing the lamp

1. At the same time, with the fingers expand up and down the transparent cover and unhook it in the direction of the arrows.

Closing the door

1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Authorised Service Centre.
Page 9 of the Progress PK1203 user manual — Technical data
Page 9 · click to enlarge
Page 9

INSTALLATION

Positioning

  • The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician.
  • The manufacturer declines all responsibility if the above safety precautions are not observed.
  • This appliance complies with the E.E.C. Directives.

This appliance can be installed in a dry, well ventilated indoor where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

SN +10°C to + 32°C

N +16°C to + 32°C

Ventilation requirements

ST +16°C to + 38°C

The airflow behind the appliance must be sufficient.

T +16°C to + 43°C

Some functional problems might occur for some types of models when operating outside of that range. The correct operation can only be guaranteed within the specified temperature range. If you have any doubts regarding where to install the appliance, please turn to the vendor, to our customer service or to the nearest Authorised Service Centre.

5 cm min. 200 cm2

min. 200 cm2

Electrical connection

  • Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply.

TECHNICAL INFORMATION

Technical data

Dimensions of the recess

Show 4 more labels / short text on this page
Cli- mate class · Ambient temperature · Height mm 1225 · Width mm 560
Page 10 of the Progress PK1203 user manual — ENVIRONMENT CONCERNS
Page 10 · click to enlarge
Page 10

Voltage Volts 230 - 240

The technical information are situated in the rating plate, on the external or internal side of the appliance and in the energy label.

ENVIRONMENT CONCERNS

dispose appliances marked with the symbol

Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not

with the household waste. Return the product to your local recycling facility or contact your municipal office.

Depth mm 550 · Frequency Hz 50

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The appliance does not oper- ate.The appliance is switched off.Switch on the appliance. p.7
The appliance does not oper- ate.The mains plug is not con- nected to the mains socket correctly.Connect the mains plug to the mains socket correctly. p.7
The appliance does not oper- ate.There is no voltage in the mains socket.Connect a different electrical appliance to the mains socket. Contact a qualified electrician. p.7
The appliance is noisy.The appliance is not sup- ported properly.Check if the appliance stands stable. p.7
The lamp does not work.The lamp is in stand-by.Close and open the door. p.7
The lamp does not work.The lamp is defective.Refer to "Replacing the lamp". p.7
The compressor operates continually.Temperature is set incor- rectly.Refer to "Operation" chapter. p.7
The compressor operates continually.Many food products were put in at the same time.Wait some hours and then check the temperature again. p.7
The compressor operates continually.The room temperature is too high.Refer to climate class chart on the rating plate. p.7
The compressor operates continually.Food products placed in the appliance were too warm.Allow food products to cool to room temperature before stor- ing. p.7
The compressor operates continually.The door is not closed cor- rectly.Refer to "Closing the door". p.7
Water flows inside the refrig- erator.The water outlet is clog- ged.Clean the water outlet. p.7
Water flows inside the refrig- erator.Food products prevent that water flows into the water collector.Make sure that food products do not touch the rear plate. p.7
Water flows on the floor.The melting water outlet is not connected to the evap- orative tray above the com- pressor.Attach the melting water outlet to the evaporative tray. p.7
The temperature in the appli- ance is too low/too high.The temperature regulator is not set correctly.Set a higher/lower temperature. p.8
The temperature in the appli- ance is too low/too high.The door is not closed cor- rectly.Refer to "Closing the door". p.8
The temperature in the appli- ance is too low/too high.The food products' tem- perature is too high.Let the food products tempera- ture decrease to room temper- ature before storage. p.8
The temperature in the appli- ance is too low/too high.Many food products are stored at the same time.Store less food products at the same time. p.8
The temperature in the appli- ance is too low/too high.The door has been opened often.Open the door only if necessa- ry. p.8
The temperature in the appli- ance is too low/too high.There is no cold air circula- tion in the appliance.Make sure that there is cold air circulation in the appliance. p.8

Ask about the Progress PK1203

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Progress PK1203

Be the first to ask — other owners or our team will answer.

Original document

Progress PK1203 manual PDF

48 pages·1.2 MB·Refrigeration and freezing·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…