EN
Progress logo
Official user manual

Progress PK1041

44 pages·2.1 MB·Refrigeration and freezing·PDF·ENITJA
Progress PK1041
Table of Contents 11 sections CONTENTS · SAFETY INSTRUCTIONS · OPERATION · FIRST USE · … ShowHide
Page 3 of the Progress PK1041 user manual — DAILY USE
Page 3 · click to enlarge
Page 3
  • Make sure that the mains plug is accessible after the installation of the appliance.
  • Connect to potable water supply only (If a water connection is foreseen).

in either its refrigerant circuit or insula- tion materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appli- ance shall be disposed according to the applicable regulations to obtain from your local authorities. Avoid dam- aging the cooling unit, especially at the rear near the heat exchanger. The ma- terials used on this appliance marked by the symbol are recyclable.

  • Service
  • Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person.
  • This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used.

This appliance does not contain gasses which could damage the ozone layer,

OPERATION

Switching on Insert the plug into the wall socket. Turn the Temperature regulator clockwise to a medium setting.

A medium setting is generally the most suitable.

  • However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on:
  • room temperature
  • how often the door is opened
  • the quantity of food stored
  • the location of the appliance.

Switching off To turn off the appliance, turn the Tempera- ture regulator to the "O" position.

  • Temperature regulation The temperature is automatically regulated. To operate the appliance, proceed as follows:
  • turn the Temperature regulator toward lower settings to obtain the minimum coldness.
  • turn the Temperature regulator toward higher settings to obtain the maximum coldness.

FIRST USE

Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accesso- ries with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly.

DAILY USE

Freezing fresh food The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time.

To freeze fresh foods it is not necessary to change the medium setting. However, for a faster freezing operation, turn the temperature regulator toward high-

Environment Protection

Page 4 of the Progress PK1041 user manual — OPERATION
Page 4 · click to enlarge
Page 4

er settings to obtain the maximum cold- ness.

Thawing Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, de- pending on the time available for this opera- tion. Small pieces may even be cooked still fro- zen, directly from the freezer: in this case, cooking will take longer.

Storage of frozen food When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run at least 2 hours on the higher settings.

Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment.

The symbols show different types of frozen goods. The numbers indicate storage times in months for the appropriate types of frozen goods. Whether the upper or lower value of the indicated storage time is valid depends on the quality of the foods and treating be- fore freezing.

Progress PK1041 — OPERATION diagram (page 4)
Fig. 1
Progress PK1041 — OPERATION diagram (page 4)
Fig. 2

The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

Frozen Food Calendar · Temperature Indicator · Movable shelves

Page 5 of the Progress PK1041 user manual — HELPFUL HINTS AND TIPS
Page 5 · click to enlarge
Page 5

Positioning the door shelves

To permit storage of food packages of vari- ous sizes, the door shelves can be placed at different heights. To make these adjustments proceed as fol- lows: gradually pull the shelf in the direction of the arrows until it comes free, then reposi- tion as required.

HELPFUL HINTS AND TIPS

  • Hints for energy saving
  • Do not open the door frequently or leave it open longer than absolutely necessary.
  • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.

Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible. Milk bottles: these should have a cap and should be stored in the bottle rack on the door. Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigera- tor.

  • Hints for freezing To help you make the most of the freezing process, here are some important hints:
  • the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate;
  • the freezing process takes 24 hours. No further food to be frozen should be added during this period;
  • only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
  • prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
  • wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
  • do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter;
  • lean foods store better and longer than fatty ones; salt reduces the storage life of food;
  • Hints for fresh food refrigeration To obtain the best performance:
  • do not store warm food or evaporating liquids in the refrigerator
  • do cover or wrap the food, particularly if it has a strong flavour
  • position food so that air can circulate freely around it

Hints for refrigeration Useful hints: Meat (all types) : wrap in polythene bags and place on the glass shelf above the veg- etable drawer. For safety, store in this way only one or two days at the most. Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf. Fruit and vegetables: these should be thor- oughly cleaned and placed in the special drawer(s) provided.

Page 6 of the Progress PK1041 user manual — CARE AND CLEANING
Page 6 · click to enlarge
Page 6
  • water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
  • it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time.
  • be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time;
  • not open the door frequently or leave it open longer than absolutely necessary;
  • once defrosted, food deteriorates rapidly and cannot be refrozen;
  • do not exceed the storage period indicated by the food manufacturer.

CARE AND CLEANING

polishes to clean the interior as this will damage the surface and leave a strong odour.

This appliance contains hydrocarbons in its cooling unit; maintenance and re- charging must therefore only be carried out by authorized technicians.

Clean the condenser (black grill) and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption.

  • Periodic cleaning The equipment has to be cleaned regularly:
  • clean the inside and accessories with lukewarm water and some neutral soap.
  • regularly check the door seals and wipe clean to ensure they are clean and free from debris.
  • rinse and dry thoroughly.

Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance. For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing-up liquid added. After cleaning, reconnect the equipment to the mains supply.

Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a drain hole into a special con- tainer at the back of the appliance, over the motor compressor, where it evaporates. It is important to periodically clean the de- frost water drain hole in the middle of the refrigerator compartment channel to pre- vent the water overflowing and dripping on- to the food inside.

Defrosting the refrigerator

Page 7 of the Progress PK1041 user manual — WHAT TO DO IF…
Page 7 · click to enlarge
Page 7

as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life.

A certain amount of frost will always form around the top compartment.

To remove the frost, do these steps: 1. Switch off the appliance. 2. Remove any stored food, wrap it in several layers of newspaper and put it in a cool place. 3. Open the door. 4. When defrosting is completed, dry the interior thoroughly. 5. Switch on the appliance. 6. Set the temperature regulator to obtain the maximum coldness and run the ap- pliance for two or three hours using this setting. 7. Reload the previously removed food in- to the compartment.

  • Periods of non-operation When the appliance is not in use for long periods, take the following precautions:
  • disconnect the appliance from electricity supply
  • remove all food
  • defrost (if foreseen) and clean the appliance and all accessories
  • leave the door/doors ajar to prevent unpleasant smells. If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure.

WHAT TO DO IF…

Problem Possible cause Solution

The appliance does not operate. The lamp does not operate.

The appliance is switched off. Switch on the appliance.

The mains plug is not connected to the mains socket correctly.

Connect the mains plug to the mains socket correctly.

The appliance has no power. There is no voltage in the mains socket.

Connect a different electrical ap- pliance to the mains socket. Contact a qualified electrician.

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

The compressor oper- ates continually.

The temperature is not set cor- rectly.

Set a higher temperature.

The door is not closed correctly. Refer to "Closing the door".

The door has been opened too frequently.

Do not keep the door open longer than necessary.

Defrosting the freezer

Page 8 of the Progress PK1041 user manual — WHAT TO DO IF…
Page 8 · click to enlarge
Page 8

Problem Possible cause Solution

The product temperature is too high.

Let the product temperature de- crease to room temperature be- fore storage.

The room temperature is too high.

Decrease the room temperature.

Water flows on the rear plate of the refrigerator.

During the automatic defrosting process, frost defrosts on the rear plate.

This is correct.

Water flows into the re- frigerator.

The water outlet is clogged. Clean the water outlet.

Products prevent that water flows into the water collector.

Make sure that products do not touch the rear plate.

Water flows on the ground.

The melting water outlet does not flow in the evaporative tray above the compressor.

Attach the melting water outlet to the evaporative tray.

The temperature in the appliance is too low.

The temperature regulator is not set correctly.

Set a higher temperature.

The temperature in the appliance is too high.

The temperature regulator is not set correctly.

Set a lower temperature.

1. Disconnect the mains plug from the mains socket. 2. Remove the screw from the lamp cov- er. 3. Remove the lamp cover (refer to the il- lustration). 4. Replace the used lamp with a new lamp of the same power and specifical- ly designed for household appliances. (the maximum power is shown on the lamp cover). 5. Install the lamp cover. 6. Tighten the screw to the lamp cover. 7. Connect the mains plug to the mains socket. 8. Open the door. Make sure that the lamp comes on.

Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation".

3. If necessary, replace the defective door gaskets. Contact the Service Center.

Replacing the lamp

Page 9 of the Progress PK1041 user manual — INSTALLATION
Page 9 · click to enlarge
Page 9

TECHNICAL DATA

Dimension of the recess

Rising Time 12 h

The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.

INSTALLATION

Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.

Electrical connection Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power sup- ply socket is not earthed, connect the appli- ance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not ob- served. This appliance complies with the E.E.C. Di- rectives.

Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

SN +10°C to + 32°C

N +16°C to + 32°C

ST +16°C to + 38°C

T +16°C to + 43°C

min. 200 cm2

The airflow behind the appliance must be sufficient.

min. 200 cm2

Show 9 more labels / short text on this page
Height 1030 mm · Width 560 mm · Depth 550 mm · Voltage 230-240 V · Frequency 50 Hz · Climate · Ambient temperature · class · Ventilation requirements
Page 10 of the Progress PK1041 user manual — ENVIRONMENTAL CONCERNS
Page 10 · click to enlarge
Page 10

ENVIRONMENTAL CONCERNS

consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The appliance does not operate. The lamp does not operate.The appliance is switched off.Switch on the appliance. p.7
The appliance does not operate. The lamp does not operate.The mains plug is not connected to the mains socket correctly.Connect the mains plug to the mains socket correctly. p.7
The appliance does not operate. The lamp does not operate.The appliance has no power. There is no voltage in the mains socket.Connect a different electrical ap- pliance to the mains socket. Contact a qualified electrician. p.7
The lamp does not work.The lamp is in stand-by.Close and open the door. p.7
The lamp does not work.The lamp is defective.Refer to "Replacing the lamp". p.7
The compressor oper- ates continually.The temperature is not set cor- rectly.Set a higher temperature. p.7
The compressor oper- ates continually.The door is not closed correctly.Refer to "Closing the door". p.7
The compressor oper- ates continually.The door has been opened too frequently.Do not keep the door open longer than necessary. p.7
The product temperature is too high.Let the product temperature de- crease to room temperature be- fore storage. p.8
The room temperature is too high.Decrease the room temperature. p.8
Water flows on the rear plate of the refrigerator.During the automatic defrosting process, frost defrosts on the rear plate.This is correct. p.8
Water flows into the re- frigerator.The water outlet is clogged.Clean the water outlet. p.8
Water flows into the re- frigerator.Products prevent that water flows into the water collector.Make sure that products do not touch the rear plate. p.8
Water flows on the ground.The melting water outlet does not flow in the evaporative tray above the compressor.Attach the melting water outlet to the evaporative tray. p.8
The temperature in the appliance is too low.The temperature regulator is not set correctly.Set a higher temperature. p.8
The temperature in the appliance is too high.The temperature regulator is not set correctly.Set a lower temperature. p.8

Ask about the Progress PK1041

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Progress PK1041

Be the first to ask — other owners or our team will answer.

Original document

Progress PK1041 manual PDF

44 pages·2.1 MB·Refrigeration and freezing·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…