EN
Official user manual

Load Up 77004

40 pages·1.8 MB·Battery Charger·PDF·ENITJA
Load Up 77004
Page 1 of the Load Up 77004 user manual
Page 1 · click to enlarge
Page 1
Page 1 of the Load Up 77004 user manual
Page 2 of the Load Up 77004 user manual
Page 2 · click to enlarge
Page 2

the paragraphs 5.0 "Duration of the charging process" and 6.0 "Adjustment of the charging current"). Battery charger LOAD UP 77007 with starter: The battery charger with starter is a device capable of supplying a strong current, which is necessary to start the vehicle. Besides the inner thermal protection with automatic reset device, the machines are provided with an amperometric protection with fuse reset. Make sure that the maximum current supplied by the machine – as shown on the plate – is at least equal to or a little higher than the maximum current of the battery installed. For instance, if the battery installed in the vehicle is 88 Ah, its starting current is comprised between 3 and 3.5 times the nominal capacity, that is between 260 A and 310 A. 3.0 SAFETY REGULATIONS 1. the electrical safety of a machine without double insulation is only ensured when it is correctly connected to a well earthed system, as required by the regulations in force on the safety of electrical systems; 2. disconnect the plug from the supply mains when the machine is not in use. 3. should the input cable be damaged, turn immediately to qualified personnel. The replacement cable must have the same characteristics. 4. disconnect the plug of the input cable before connecting or disconnecting the connections to the battery. Warning: during the charging operation the battery produces explosive fumes. Avoid open flames and sparks near the battery; DO NOT SMOKE. 5. this battery charger comprises parts such as switches or relays which can cause electric arcs or sparks, therefore, if used in a garage or in a similar environment, place the battery charger in a well ventilated room suitable for this purpose; do not use it at all inside a car or a closed engine bonnet. 6. do not expose to rain, snow and other atmospheric agents in general; do not wet. 7. do not use the machine when you are barefooted. 8. do not touch the machine with wet, damp hands or feet. 9. do not pull the cable or the machine itself to disconnect the plug from the socket. 10. do not permit children or disabled people to use the machine. 11. do not leave the machine unattended or uselessly plugged in, since it can become a source of hazard.

Page 3 of the Load Up 77004 user manual
Page 3 · click to enlarge
Page 3
  • 4.0 GENERAL WARNINGS AND MODE OF EMPLOYMENT In order not to damage either the battery or the battery charger, it is necessary to observe the following operating instructions and warnings:
  • After removing the machine from its box, make sure that it is complete in all of its parts.
  • Unwind the input cable in its entire length and extend it, so that it cannot be trampled on or crushed.
  • Lengthen the input cable with an extension if necessary, make sure that the current capacity is the same as that of the original cable; do not use cables having a smaller section.
  • In case the socket and plug are not compatible, use only simple or multiple adaptors complying with the safety regulations in force and having a proper capacity.
  • The connecting clamps, the charging clips and the upper surface of the battery must always be clean; eventually clean well the clips of the battery with an iron brush.
  • Never reverse the polarity of the connections; if in doubt, remember that the negative clamp (-) is directly connected to the body of the motor vehicle.
  • The charging voltage of the battery charger must be equal to the nominal one indicated on the battery; it coincides with the number of elements of the battery mulltiplied by two (i.e. 6 elements = 12 V).
  • During the operation set the battery charger in a stable position and make sure that the openings for the passage of air are not obstructed.
  • Remove the caps of the battery once the clamps have been cleaned, so that dust or other particles do not fall into the battery elements, and leave them in this way for the entire duration of the charge.
  • Make sure that the electrolytic liquid covers the plates for at least 4-5 mm; if necessary add distilled water of the type marketed for this purpose. Warning: do not touch the liquid inside the battery; it is corrosive!
  • It is advisable to always disconnect the cables connected to the positive pole of the battery.
  • Do not perform the simultaneous charging of several batteries.
  • Avoid any attempt of re-charging batteries which cannot be re-charged.
  • Keep the battery charger in a dry place. 5.0 DURATION OF THE CHARGING PROCESS The duration of the charging process always depends on the situation of the battery to be charged (almost charged, half-way or completely discharged) and on its conditions. To "rejuvenate" a battery normally in use, 2 to 4 hours are usually sufficient. For a complete re-charge 8 to 10 hours may be necessary.
Page 4 of the Load Up 77004 user manual
Page 4 · click to enlarge
Page 4

At the beginning of the charging process, the current acquires a high value which slowly and gradually decreases until it becomes very low as the battery is being charged. When the battery is under charge, it may be noticed that the liquid held inside it begins to boil. It is better not to prolong the charge excessively, so as not to overheat the elements and avoid oxidations of the plates. This will help to maintain the battery in good condition. 6.0 ADJUSTMENT OF THE CHARGING CURRENT Model 77001-77002-77004-77006: With the proper multi-position regulator (3) it is possible to increase or decrease the charging current and, consequently, the speed at which the battery is charged. In order to prolong the battery life span, it is advisable to charge it slowly, with a charging current indicated by the instrument, comprises between 1/10 and 1/5 of the capacity in Ah of the accumulator. Start the charge with the adjusting commutator on position "MIN". The ampmeter shows the current required at that moment by the battery. When the index of the ampmeter is nearing zero, increase by turning the adjusting commutator to “BOOST”. Proceed in this way for the next positions (when they are present) until the charge is complete. When the battery is charged, it is important to stop the machine as soon as possible, because otherwise the battery charger will keep on charging and the battery may be damaged. Model 77007 with starter: On position “1” the machine charges a minimum current and on position 3 (without timer) a maximum current. On these positions the machine will keep on charging and has to be stopped as soon as the battery is charged. Or use position 4 - 6 and timer knob. On position 4 it charges a minimum current, when using position 6 a maximum current in combination with the timer knob (when using the timer knob the machine will stop after the adjusted time). On position “start” the vehicle can be started (see also point 9.1). 7.0 THERMAL PROTECTION All the Load UP model battery chargers are equipped with an amperometric protection against overloads (battery anomaly or incorrect connection) short circuit (direct contact of the charging pliers) and polarity inversion. ♦ Models Load UP 77001-77002-77004-77006 are preset for the charging of 12 & 24 V batteries only, they only have two charging adjustments (MIN-BOOST)

Page 5 of the Load Up 77004 user manual
Page 5 · click to enlarge
Page 5
  • and are provided with an automatic amperometric resetting protection (secondary) and fuse (primary) inside the machine. ♦ Model Load 77007 has amperometric protection for the rectifier and a protective device for the transformer. The starter has a fuse. 8.0 TROUBLE SHOOTING If, once all the connections have been completed following the above instructions, the thermal protection is tripped and the ampmeter reaches the bottom of the scale, the causes can be traced to:
  • reversal of polarity in connecting the pliers to the battery: eliminate the problem by resetting the thermal protection by pushing the proper push-button for the manual one or wait a few minutes for the automatic one.
  • casual or indirect contact between the charging pliers: eliminate the contact, reset the thermal protection manually or wait a few minutes for the automatic one.
  • battery completely discharged and at a higher capacity than the power of the battery charger: if the absorption of the battery is excessive, it is advisable to have the battery re-charged by a motor vehicle electrician and later maintain it at a high charging level with the frequent use of the battery charger or to get a more powerful battery charger.
  • battery with inner elements in short circuit: it is necessary to replace the battery. For other types of inconveniences call your local dealer or a qualified technical engineer. 9.0 FIRST START UP MODELS WITHOUT STARTER (77001-77002-77004-77006) After following all the above instructions proceed as follows: 1. Check that the mains voltage corresponds to the nominal one of the battery charger indicated on the plate. 2. Disconnect the cables connected to the positive pole (+) of the battery. 3. Untie the caps of the battery and check the level of the electrolytic liquid. 4. Connect in sequence: - the red clamp to the positive pole (+) - the black clamp to the frame of the car, away from the battery and from the fuel pipe. 5. Find out the voltage of the battery to be charged (12 or 24 V) and position the proper commutator of the battery charger on the same value. 6. Start the battery charger, check the position which the indicator of the ampmeter will acquire. 7. Adjust the charging current with the proper commutator (MIN-BOOST).
Page 6 of the Load Up 77004 user manual
Page 6 · click to enlarge
Page 6

8. To interrupt the charge, disconnect in sequence: - the supply cable - the negative conductor (-) - the positive conductor (+) 9.1 FIRST START UP MODEL WITH STARTER (77007) After following all the above instructions proceed as follows: CHARGE 1. Check that the mains voltage corresponds to the nominal one of the battery charger indicated on the plate. 2. Disconnect the cables connected to the positive pole (+) of the battery. 3. Untie the caps of the battery and check the level of the electrolytic liquid. 4. Connect the black cable to the negative attachment of the battery charger 5. Find out the voltage of the battery to be charged (12 or 24 V) and connect the red cable to the corresponding attachment (+12 V) or (+24 V). 6. Connect in sequence: - the red clamp to the positive pole (+) - the black clamp to the frame of the car, away from the battery and from the fuel pipe. 7. Start the battery charger; check the position which the indicator of the ampmeter will acquire. 8. Adjust the charging current with the proper switch, to max. 10% of battery power, with a max. of 40 ampere. Concerning the positions of the switch:

- Without timer: pos.1(low), 2 (medium) and 3 (high) - With timer: 4(low), 5 (medium) and 6 (high) 9. Connect the input cable to the mains 230 V. 10. To interrupt the charge, disconnect in sequence: - the supply cable - the negative conductor (-) - the positive conductor (+)

STARTER: 1. In case of very large engines and severe weather conditions, it is advisable to give the battery a quick charge for a few minutes before you try to jump it (see above charging instructions). 2. Contrary to the charging operations, during the starting process the battery must remain connected to the vehicle and the caps must remain closed. 3. N.B. Attempts of starting with the battery charger preset in the “charge” position (pos.1-6) may damage the ampmeter and trigger the thermal protection. 4. N.B.* The operation of the battery charger in the “START” position should possibly occur shortly after the ignition key of the vehicle has been turned on and be interrupted as soon as the vehicle is started; otherwise the high current

Page 7 of the Load Up 77004 user manual
Page 7 · click to enlarge
Page 7

supplied by the machine may damage the battery, if it continues to flow for more than 5-6 seconds. 5. Now follow the specific instructions for model 77007: 6. Connect the black cable to the negative attachment of the battery charger. Find out the voltage of the battery to be charged (12 or 24 V) and connect the red cable to the corresponding attachment (+12 V) or (+24 V). 7. Connect in sequence: - the red clamp to the positive pole (+) - the black clamp to the frame of the car, away from the battery and from the fuel pipe. 8. Position the charging regulator on (0). 9. Connect the input cable to the mains 230 V. 10. Set the commutator directly on the “START” position. 11. within 5 seconds at the latest, start the vehicle (see preceding N.B.*). 12. position the charging regulator on (0). 13. Disconnect the machine if the vehicle is started, or repeat the operation after a few minutes, if necessary. TECHNICAL DATA: Model BC-10 BC-20 BC-30 BC-30 BC-730 Article no. 77001 77002 77004 77004 77007 Max. charging current (A) 8 16 25 40

40 700 (5 sec., starter) Battery capacity (Ah) 12-100 25-125 30-200 40-400 40-1500 Volt 12/24 Dimensions (lxbxh, mm) 275x205x225 275x205x225 295x254x235 315x280x240 350x295x680 Weight (kg) 2,9 3,8 4,5 10,5 30 Starter no yes LOAD UP 77001-77002-77004- 77006 Panel 1 Handle 2 Amperemeter 3 Selector switch charging current 4 On / off switch 5 Selector switch 12/24 V 6 Mains fuse 7 Charging cabels 8 Power plug & cable 9 Housing 10 Amperometric protection

Load Up 77004 diagram (page 7)
Fig. 1
Load Up 77004 diagram (page 7)
Fig. 2
Page 8 of the Load Up 77004 user manual
Page 8 · click to enlarge
Page 8
Load Up 77004 diagram (page 8)
Fig. 3
Load Up 77004 diagram (page 8)
Fig. 4
Load Up 77004 diagram (page 8)
Fig. 5

LOAD UP 77007 Panel

Load Up 77004 diagram (page 8)
Fig. 6

1 Selector switch current charge / start 2 Timer 3 Connection 12 V 4 Connection 24 V 5 Fuse 6 Display Wiring plan

Load Up 77004 diagram (page 8)
Fig. 7

Wiring plan

Ask about the Load Up 77004

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Load Up 77004

Be the first to ask — other owners or our team will answer.

Original document

Load Up 77004 manual PDF

40 pages·1.8 MB·Battery Charger·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…