


power supply after use. 3.0 PREPARATION 1. Ensure the machine is turned off. 2. Join the earth clamp to the workpiece to be welded. Never join the clamp to a wooden bench or painted surface, in such cases there would be no current induction. 3. The other end of the earth lead should be connected to the machine. This should already be done. 4. Insert the electrode into the electrode holder. Ensure there is good connection, the other end should be connected to the machine. Ensure welding surfaces are kept clean. 5. Set amperage by regulating control wheel according to visual scale relating to amperage/electrode diameter. This is shown on the front or side of the machine. 3.1 YOU ARE NOW READY TO WELD Switch on only when you are ready to start welding and the electrode is in position. Practice on scrap metal first. Tap the electrode lightly to strike arc and maintain a steady gap thereafter of about 2 mm between the end of the electrode and the metal being welded. Withdraw with a clean movement at the end of the run. You will notice a slight tendency to pull to the right. A few minutes practice will ensure that you get used to this and compensate when doing a proper job. If the electrode sticks you may be holding it too closely. Pull sharply to the left and right to free it. After welding chip off slag with chipping hammer. You should wear goggles when doing this. 4.0 IMPORTANT - THERMOSTAT CONTROL Your welder is cooled by the circulation of air. If you use the machine with 16 gauge (1.5 mm rods) it will operate continuously. As larger diameter rods are used you will experience the current being temporarily shut off. This is to protect your transformer from overheating. Obviously the larger the rod the more current and consequently the hotter the machine becomes. The table below shows the number of electrodes which you can weld per hour. The welder will produce up to 210 amps on 230 V power supply, depending on welder size. When using larger electrodes or for better performance use 400 V 3- phase. The position of the switch should be changed. Consult a qualified electrician. diameter electrode
1.6 2 2.5 3.2 4 5
60 75 48 55 28 33 14 18 8 12 current (amps)
60 80 80 120 116 160 160 190 210 250
electrodes per hour

5.0 SOME POSSIBLE PROBLEMS 1. Burning through thin metal. On very thin sheet eg-car bodywork, even the lowest amperage setting will be too fierce. In this case you can still use your welder but you will need a brazing kit which is available from your stockist. 2. Machine cuts out frequently. This is probably caused by a sticking electrode. Even one sticking electrode could cause the machine to cut out for up ten minutes. After this time it should be ready to use again. 3. Difficulty in striking an arc can be experienced if the electrode is damp. Heat it up to 60o-70o before using. 4. Difficulty in striking an arc can be experienced if you use the wrong type of rod. Only ACID or RUTILE electrode can be used with these machines. BASIC electrodes are unsuitable for these machines. 6.0 VARIOUS WELDING SYSTEMS 1. For metal up to 7 mm thick, keep pieces 2-3 mm apart. A second run can go under- neath for extra strenght. See illustration. 2. For thicknesses up to 30 mm a single butt joint is necessary, filling up the space with several layers of weld. See illustration. 3. Over 30 mm you will need a double "V" butt joint and again fill up the space. See illustration. 7.0 GRAPHICAL SYMBOLS ELECTRODE HOLDER Use only electrodes as stated in chapter 4.0. EARTH CLAMP This must be clamped to the work- piece. The machine will not work unless in contact with bare metal.




POWER SUPPLY CABLE This should be connected as shown below. TURBO FAN This cools the machine as it runs to prevent overheating. PILOT LIGHT This is lit when the machine is overheatet. 8.0 LIMITATION OF USE Do not use in following conditions: 1. Outside when raining. 2. Do not use cable reels unless completely unwound and fitted with a thermal cut-out. 3. Do not use above 140 amp. with 16 amp. fused 230 volt power supply. 9.0 PLUG WIRING IMPORTANT: For adequate performance on 230 V you will need a 25 amp. fused supply. When using a 1-phase 230 V power supply wire the plug as in chapter 9.1. If the machine is to be operated on a 400 V 3-phase supply connections should be made as in chapter 9.2. If in doubt of electrical connections consult a qualified electrician. 9.1 230 V (1-PHASE) CONNECTIONS (E 100, E 145, E 165, E 205) Use of a 16 amp. plug is only recommended up to a power output of 140 amp. For use above this amperage consult an electrician. EARTH green/yellow wire NEUTRAL LIVE blue wire brown wire





9.2 INFORMATION FOR PROFESSIONAL ELECTRICIANS (E 205) 400 VOLT (3-PHASE) CONNECTIONS yellow/green - earth blue - 1 live phase brown - 1 live phase 9.3 CONNECTIONS E 260 brown = R (L1) black = S (L2) blue = T (L3) yellow/green = earth You can weld with a power output of 400 V/50 Hz/3 phase or 230 V/50 Hz/ 3 phase. The switch high/low is used by extreme low welding values (turn the switch to “low”) or extreme high welding values (turn the switch to “high”). 10.0 TECHNICAL DATA Type E 100 Winding aluminium Volt 230 KVA 3,7 Ignition voltage 33-38 Adjusting range (amp) 60-85 Electrode φ (mm) 1,6-2,5 Dimensions (lxwxh) (mm) 260 x 195 x 185 Weight (kg) 9,5 Ordernumber 76055 Type E 145 Winding copper Volt 230 KVA 3,8 Ignition voltage 41-46 Adjusting range (amp) 30-105 Electrode φ (mm) 1,6-2,5 Dimensions (lxwxh) (mm) 350 x 270 x 240 Weight (kg) 18 Ordernumber 76056

Type E 165 TURBO Winding copper Volt 230 KVA 4,0 Ignition voltage 42-48 Adjusting range (amp) 65-135 Electrode φ (mm) 1,6-3,2 Dimensions (lxwxh) (mm) 350 x 270 x 240 Weight (kg) 21 Ordernumber 76057 Type E 205 TURBO With removable welding cables. Winding copper Volt 230 and 400 KVA at 230 volt 5,0 at 400 volt 7,5 Ignition voltage at 230 volt 31-39 at 400 volt 42-50 Adjusting range (amp) at 230 volt 20-110 at 400 volt 60-180 Electrode φ (mm) 1,6-4,0 Dimensions (lxwxh) (mm) 375 x 315 x 270 Weight (kg) 25 Ordernumber 76058 Type E 260 SUPER Mobile, with removable welding cables. Winding copper Volt 230 and 400 KVA at 230 volt 8,5 at 400 volt 10,0 Ignition voltage at 230 volt 45-51 at 400 volt 48-55 Adjusting range (amp) at 230 volt 45-220 at 400 volt 50-250 Electrode φ (mm) at 230 volt 2,0-4,0 at 400 volt 2,0-5,5 Dimensions (lxwxh) (mm) 705 x 410 x 385 Weight (kg) 55 Ordernumber 76059
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.