EN
Official user manual

Load Up 75050-1

36 pages·2.3 MB·Generator·PDF·ENFRITNLJA
Load Up 75050-1
Table of Contents 7 sections 2. TECHNICAL SPECIFICATIONS · MAINTENANCE · Every year or 1000 hrs Check and refill fuel oil • · 10. TROUBLESHOOTING AND REMEDY · … ShowHide
Page 1 of the Load Up 75050-1 user manual
Page 1 · click to enlarge
Page 1

ENGLISH CONTENTS 1. Safety instructions 17 2. Technical specifications 18 3. Preparation for starting 19 4. Start the generating set 21 5. Operate the generating Set 21 6. Load 22 7. Stop the generating set 24 8. Periodic checks and service 24 9. Long-term storage 28 10. Troubleshooting and remedy 29 ATTENTION Before using your LOAD-UP generator, first read this manual thoroughly, so that accidents can be prevented. GENERAL Having bought the LOAD-UP generator, you have become the owner of a high quality, reliable machine. Using it properly and maintaining it regularly, the generator will carry out heavy jobs for years to come. In this operation manual you will find use and maintenance prescriptions. Before using the generator, read this manual first and be sure that others have read it as well and have taken the necessary precautions. This generator has been designed and intended for generating electricity. The appliance must be used only for the purpose for which it was specifically designed. All other uses are to be considered incorrect and therefore unreasonable. The manufacturer cannot be held responsible for any damage resulting from improper, incorrect or unreasonable use. 1. SAFETY INSTRUCTIONS Working with generators is not without danger. To reduce this danger as much as possible, we have drawn up a number of safety measures. Always follow up these directives and always be aware of what you are doing. In this way many accidents can be avoided.

  • Exhaust gas contains poisonous carbon monoxide. Never run the generator in an enclosed area. Be sure to provide adequate ventilation.
  • The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Be careful not to touch the muffler while it is hot. Let the engine cool before storing the generator indoors. The engine exhaust
Page 2 of the Load Up 75050-1 user manual
Page 2 · click to enlarge
Page 2

system will be heated during operation and remain hot immediately after stopping the engine.

  • Diesel oil is extremely flammable and explosive under certain conditions. Refuel in a well ventilated area with the engine stopped.
  • Keep away from cigarette, smoke and sparks when refueling the generator. Always refuel in a well-ventilated location.
  • Wipe up spilled diesel oil at once.
  • Connections for standby power to a building’s electrical system must be made by a qualified electrician and must comply with all applicable laws and electrical codes. Improper connections can allow electrical current from the generator to back feed into the utility lines. Such back feed may electrocute utility company workers or others who contact the lines during a power outage, and when utility power is restored, the generator may explode, burn, or cause fires in the building’s electrical system.
  • Always make a pre-operation inspection before you start the engine. You may prevent an accident or equipment damage.
  • Place the generator at least 1 m away from buildings or other equipment during operation.
  • Operate the generator on a level surface. If the generator is tiled, fuel spillage may result.
  • Know how to stop the generator quickly and understand operation of all the controls. Never permit anyone to operate the generator without proper instructions.
  • Keep children and pets away from the generator when it is in operation.
  • Keep away from rotating parts while the generator is running.
  • The generator is a potential source of electrical shocks when misused; do not operate with wet hands.
  • Do not operate the generator in rain or snow and do not let it get wet.
  • WARNING: the warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
  • Only those persons who are aware of how to use the generator by having read this manual, should use the machine. Injudicious use may cause danger.
Page 3 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 3 · click to enlarge
Page 3

2. TECHNICAL SPECIFICATIONS

Generator 75050/1: GENERATOR DATA Rated frequency (Hz) 50 Rated power (kW) 5 Rated voltage (AC) (V) 230 Rated current (AC) (A) 21,7 Rated revolution speed (rpm) 3000 Phases single Power factor (cosø) 1 Excitation mode controlled silicon self excitation constant voltage DC output 12 V/8,3A Operation mode 12 hours continuous running Structure mode Hand cart type Coupling method Transmission rigid connection Gross weight (kg) 171 Overall dimensions (LxWxH mm) 930 x 515 x 755 MOTOR DATA Type 4-stroke, single cylinder, direct injection diesel engine Continual output (kW/rpm) 5,7/3000 Max. power (kW/HP/rpm) 6,3/8,6/3300 Bore x stroke (mm) 86 x 72 Displacement (l) 0,418 Cooling system Forced air cooling Lubrication system Pressure splashing Lube oil capacity (l) 1.65 Starting system Electric starter Fuel oil Diesel oil Fuel tank volume (l) 16 Low oil alarm system Will switch off the engine Sound pressure level dB(A)/7 m 68

Page 4 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 4 · click to enlarge
Page 4
  • 3. PREPARATION BEFORE STARTING 3.1 Selection and handling of the fuel oil
  • Selection of fuel oil Only use the light diesel, which is most suitable for the engine.
  • Keep dust and water out of the fuel When filling the fuel tank from drums, make sure that no dust or water is mixed in the fuel. Otherwise the serious fuel injection pump and nozzle problems will result.
  • Do not overfill Overfilling is very dangerous. Do not fill the tank beyond the top of the red plug inside the fuelfilter. Warning:
  • Refuel in a well-ventilated area with the engine stopped.
  • Do not smoke or allow flames or sparks in the area where the engine is refueled or where the fuel is stored.
  • Do not overfill the tank, make sure the filtercap is securely closed after refueling.
  • Be careful not to spill fuel when refueling. If any fuel is spilled, make sure the area is dry before startng the engine. 3.2 Check and refill engine oil. Warning:
  • Always check the engine oil level with the generating set on a level surface before starting and refill necessary.
  • The engine may be damaged if operated with insufficient engine oil, it is also dangerous to refill too much engine oil as sudden increase in engine speed may caused by combustion. Warning: These series generating set are equipped with low oil warning system. This system wil stop the engine automatically when the oil level falls below the lower level. This prevents accidents such as bearing seizures, etc. We recommend to use SAE 15W-40 (multigrade) oil. 3.3 Service the air cleaner 1. Screw off the wing nut, remove the air cleaner cover and take out the element. Caution:
  • Do not wash the element with detergent.
  • Replace the element when its output decrease or a bad exhaust color is noticed.
Page 5 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 5 · click to enlarge
Page 5
  • Never run the generating set without the element, otherwise the rapid engine wear wilt result. 2. Reattach the air cleander cover and screw on the wing nut. 3.4 Check the generating set - Turn of the main switch to “STOP”and disconnect the electric equipment. Warning:
  • Be sure to turn off the main switch before starting.
  • The generatingg set should be earthed to prevent electric shocks Caution:
  • The main switch should always be kept in the "ON" position during operation.
  • Before starting the engine, be sure to turn the switches of the working instrument (lighting apparatus, motor, etc.) to their "OFF" position. If the switches are not "OFF", the sudden application of load when the engine is started could be very dangerous. 3.5 How to open the cabinet door 1. Open the cabinet door for daily inspection. Turn the lever counterclockwise and raise the door. 2. Loosen the bolt of the air cleaner check port cover to check the air cleaner. 3.6 Break-in period operation The first 20 hours are the break-in period of the engine, the operator must obey to following items:
  • Warm up the engine 5 minutes after the initial starting. Run the engine at low speed and zero load before the engine becomes warm.
  • Avoid applying any heavy loads during the break-in period. We recommend to run the engine at 3000 rpm with 50% load in break-in period. Replace the engine oil in time.
  • Replace the engine oil while the engine is warm after 20 hour running, the old engine oil will be drained out completely. Replace the oil: after the first month or 20 operation hours; then every 3 months or operation 100 hours. Always respect the regulations in force for disposing of old oil! 3.7 Cooling system Model 75050/1 has forced air cooling.
Page 6 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 6 · click to enlarge
Page 6
4. START THE GENERATING SET Warning: Do not hook up tools or other apparatus to the generating set before starting. Turn the starting key to “ON” position. Now you turn the starting key to “START”. Wenn the motor is running, you can turn the starting key to “ON” position.
  • Caution:
  • Running the starting motor for a long time will cost the battery power greatly even burn out the motor
  • Always leave the starting key at ON position while the engine is running

BATTERY Check the battery electrolyte level every month. Refill the distelled water until the upper limits if the electrolyte dropped to the lower limits. Caution: If the electrolyte level is too low, the engine may fail to start because there is not sufficient power. On the other side, if the electrolyte level is too high, the fluid will corrode the surrounding parts.Do keep the electrolyte level between the upper and lower limits.

  • 5. OPERATE THE GENERATING SET 5.1 Operate the generating set 1. Warm up the engine without load three minutes. 2. Concerning the generating set with Low Oil Warning System, check that the Oil Alarm Lamp is not lit. Caution:
  • For the generating set with Low Oil Warning System, the oil alarm lamp will activated by low oil pressure or engine oil shortage, simultaneously, the engine will stop. The engine will stop immediately if restarted without refilling engine oil. Check the oil level and refill.
  • Do not loosen or readjust either the engine speed limiting bolt or fuel injection limiting bolt, otherwise, the performance will be affected.

5.2 Checks during the running 1. Whether there is abnormal sound or vibration; 2. Whether the engine misfires or runs rough; 3. Check the color of the exhaust. (Is it black or too white?) If you notice any of the above-mentioned phenomenon happened, stop the engine and find out the fault cause or contact with our agents.

Page 7 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 7 · click to enlarge
Page 7
  • Caution:
  • If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler.
  • Never refill the fuel tank while the engine is running. 6. LOAD Caution:
  • Do not start 2 or more machines simultaneously. Start them one by one.
  • Do not use floodlights together with other machines. 6.1 AC application 1. Be sure to run the generating set at rated speed, otherwise VAV (Automatic Voltage Regulator) will produce the forced axcitation. If the running is for a long time under such condition, AVR will be burned out. 2. When the double voltage generating set changes over the voltage, the air SW ILI should be set at "OFF" position. Otherwise the generating set and electric devices will be burned out and damaged. 3. Connect the equipment to the generating set in order. For the matter of the motor load, firstly the heavy-duty motor should be connected, then the lightduty motors. If the operation is false, the generating set will lag or stop suddenly. It is necessary to unload the generating set immediately and turn off the main switch and do checks. NOTE If overloading of the circuit trips the AC circuit protector, reduce the electrical load on the circuit, and wait a few minutes before resuming operation. 6.2 DC Application 1. DC terminals are only for charging 12 V battery. 2. Set the air switch at OFF position while charging. On the 12 V output terminals, a charge switch can be connected so the switch can be used for on-and-off purpose. 3. Concerning the automatic type battery with leads, be sure to disconnect the negative leads of the battery while charging. Caution:
  • Connect the positive and negative poles of the battery with the positive and negative poles of DC terminals separately. Do not confuse them, otherwise the battery and generating set will burn out.
  • Do not connect the positive pole of the battery with its negative pole, otherwise the battery damage will result.
  • Do not connect the positive pole of the DC terminal with its negative pole, otherwise the generating set damage will result.
  • When large capacity battery is charged, excessive current flows, the fuse for the direct current will burn out.
Page 8 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 8 · click to enlarge
Page 8
  • Do not run the generating set while it is still connected with the battery.
  • Do not use DC12V and AC at the same time. Caution:
  • Battery exhausts explosive gas. Keep sparks, flames, and cigarettes away form the battery. To prevent from creating a spark near the battery, always connect the charging cables to the battery first and only then to the generating set. When disconnecting, you should disconnect the cables at the generating set first.
  • Charge the battery at a well-ventilated place.
  • Before charging, remove the cap from each cell of the battery.
  • Stop charging if the electrolyte temperature exceed 45C.

6.3 Electric appliance particularly moto-driven equipment will produce very high current while starting, below the table provides the reference for connecting these apparatus to the generating set.

Page 9 of the Load Up 75050-1 user manual — 2. TECHNICAL SPECIFICATIONS
Page 9 · click to enlarge
Page 9
7. STOP YOUR GENERATING SET 1. Disconnect the load from the generating set. 2. Turn off the air switch of the generating set.
  • Warning:
  • Do not stop the engine with the decompression lever.
  • Do not stop the generating set with load. Stop it after the load removed.
  • 8. PERIODIC CHECK AND SERVICE Periodic check and service are very important fot keeping the engine in good condition and durable. The chart below indicates what checks to make and when to make them. Warning:
  • Shut off the engine before performing any service. If the engine must be run, make sure the area is well ventilated. The exhaust contains poisonous carbon monoxide gas.
  • After the generating set has been used, clean it immediately with a cloth to prevent corrosion and to remove sediment.
Page 10 of the Load Up 75050-1 user manual — Every year or 1000 hrs Check and refill fuel oil •
Page 10 · click to enlarge
Page 10

MAINTENANCE

Load Up 75050-1 — MAINTENANCE diagram (page 10)
Fig. 1

Every year or 1000 hrs Check and refill fuel oil •

The generating set has been stored more than 10 days.

Page 11 of the Load Up 75050-1 user manual — MAINTENANCE
Page 11 · click to enlarge
Page 11

8.1 Replace engine oil Remove the oil filter cap. Remove the drain plug and drain the old oil while the engine is still warm. The plug is located on the bottom of the cylinder block. Tighten the drain plug and refill with the recommended oil. 8.2 Clean the engine oil filter Cleaning time: Every 6 months or 500 hours. Replace if necessary. 8.3 Replace the air cleaner element. Do not clean the aircleaner with detergent. Replace time: Every 6 months or 500 hours. Caution: • Never run the engine without the element or with a defective element. 8.4 Clean and replace fuel oil filter The fuel oil filter also has to be cleaned regularly to insure maximum engine output. Cleaning time: Every 6 months or 500 hours. Replace time: Every year or 1000 hours. 1.Drain out the fuel from the fuel tank. 2. Drain out the fuel from the fuel tank. Screw off the small screw of the fuel cock and pull out the filter from the filler port. 3. Wash the filter thoroughly with diesel fuel. Loosen the fastening nut, bottom cover and delivery discs for cleaning the deposit carbon.

Page 12 of the Load Up 75050-1 user manual — MAINTENANCE
Page 12 · click to enlarge
Page 12
  • 8.5 Tighten cylinder head bolt Tightening the cylinder head bolt requires a special tool. Do not try yourself. Contact with our agents. 8.6 Check the injection nozzle and fuel injection pump 1. Adjust the clearance of the intake/exhaust valves. 2. Grind the intake/exhaust valves. 3. Replace the piston'ring. All these operation require special tools and skills, contact with your our agents. Warning:
  • Do not perform the injection nozzle test near an open fire or any other kind of fire. The fuel spray may ignite. Do not expose bare skin to the fuel spray. The fuel may penetrate the skin and cause injury to the body. Always keep your body away from the nozzle. 8.7 Check and refill the battery electrolyte and charge the battery The diesel uses a 12 V battery. Battery electrolyte will be lost through continuous charging and discharging. Before starting, check for physical damage to the battery and also the electrolyte levels and refill the distelled water till to the upper level if neccesary. When actual damage is discovered, replace the battery. Check the battery electrolyte monthly. Warning:
  • The battery electrolyte contains sulfuric acid. Protect your eyes, skin and clothing. In case of contact, flush thoroughly with water and get prompt medical attention, especially if your eyes are affected.
  • The battery exhaust hydrogen gas, which can be highly explosive. Do not smoke or allow flames or sparks near the battery, especially during charging. 8.8 Check the generating set carbon brush and slip ring. Often check the generating set carbon brush and slip ring. Readjust if there is spark.
Page 13 of the Load Up 75050-1 user manual — MAINTENANCE
Page 13 · click to enlarge
Page 13
9. LONG TIME STORAGE If store the generating set for long periods, make the following preparations

1 Operate the engine for about 3 minutes and then stop. 2 Stop the engine. Drain the engine oil while the engine is still warm and fill with fresh oil. 3 Remove the screw plug on the cylinder head cover and refill 2cc engine oil, then put the plug in place. 4 Turn the engine 2-3 seconds with the decompression lever set at the non-compression position, and the starting key at the "START" position.( (Do not start the engine.) 5 Wipe off the oil and dirt from the engine and store in a dry place.

Page 14 of the Load Up 75050-1 user manual — 10. TROUBLESHOOTING AND REMEDY
Page 14 · click to enlarge
Page 14

10. TROUBLESHOOTING AND REMEDY

Page 15 of the Load Up 75050-1 user manual — 10. TROUBLESHOOTING AND REMEDY
Page 15 · click to enlarge
Page 15
Page 15 of the Load Up 75050-1 user manual — 10. TROUBLESHOOTING AND REMEDY
Page 16 of the Load Up 75050-1 user manual — 10. TROUBLESHOOTING AND REMEDY
Page 16 · click to enlarge
Page 16

- - - - - - - -

Page 18 of the Load Up 75050-1 user manual — 10. TROUBLESHOOTING AND REMEDY
Page 18 · click to enlarge
Page 18

EG-verklaring van overeenstemming Wij, Load Up, postbus 114, 8900 AC Leeuwarden, Nederland, verklaren geheel onder eigen verantwoordelijkheid dat de producten Generatoren 75050/1 waarop deze verklaring betrekking heeft, in overeenstemming zijn met de volgende normen : EN 60335-1 en EN 60335-2-29 en de richtlijnen : de EMC richtlijn 89/336/EG, de CE marking richtlijn 93/68/EG, de richtlijn 72/23/EG en de richtlijn 2000/14/EG Nederland, Leeuwarden, 17 februari 2006 EG-Konformitätserklärung Wir, Load Up, Postfach 114, 8900 AC, L eeuwarden, Niederlande, erklären ganz auf eigene Verantwortung, dass die Produkte Generatore 75050/1 auf das sich diese Erklärung bezieht mit den Normen EN 60335-1 und EN 60335-2-29 übereinstimmen und den Richtlinien: EMC Richtlinie 89/336/EC, Richtlinie CE marking 93/68/EC, der Richtlinie 72/23/EC und der Richtlinie 2000/14/EC Niederlande, Leeuwarden, den 17. Februar 2006 EC-declaration of conformity We, Load Up, P.O. Box 114, 8900 AC Leeuwarden, The Netherlands, taking full responsibility, declare that the products Generators 75050/1 to which this declaration refers, comply with the norms EN 60335-1 and EN 60335-2-29 and the directives: EMC directive 89/336/EC, CE marking directive 93/68/EC, the directive 72/23/EC and the directive 2000/14/EC The Netherlands, Leeuwarden, 17th February 2006 Déclaration CE de conformité Nous, Load Up, P.O. Box 114, 8900 AC Leeuwarden, Pays Bas, déclarons entièrement sous notre propre responsabilité que les produits Générateurs 75050/1 auquel cette déclaration a trait sont conformes aux normes EN 60335-1 et EN 60335-2-29 et aux directives: la directive EMC 89/336/EC, la directive CE marking 93/68/EC, la directive 72/23/EC et la directive 2000/14/EC Pays Bas, Leeuwarden, le 17 février 2006 Declaracíon CE de conformidad Load Up, C.P. 114, 8900 AC Leeuwarden, Paises Bajos, declaramos bajo nuestra exclusiva responsabilidad la conformidad del producto Generador 75050/1 al que se refiere esta declaración, con las disposiciones de la Directiva Directivas 89/336 CE, 93/68 CE, 72/23 CE y 2000/14/CE Para lo cual se han seguido las normas EN 60335-1 y EN 60335-2-29 Paises Bajos, Leeuwarden, el 17 de febrero 2006

E.J. de Vries Directeur/Geschäftsführer/Managing director/dDirecteur général/Director gerente

Page 19 of the Load Up 75050-1 user manual — GENERATOR GENERATOR
Page 19 · click to enlarge
Page 19

Gebrauchsanleitung Instruction manual

Versie 08.2006

GENERATOR GENERATOR

75050/1

Ask about the Load Up 75050-1

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Load Up 75050-1

Be the first to ask — other owners or our team will answer.

Original document

Load Up 75050-1 manual PDF

36 pages·2.3 MB·Generator·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…