Instruction/ maintenance manual of the product ACT-IR100S ACTiSYS
Go to page of 23
.
!4 56 . This device complies with part 15 of the FCC Rules.
70+ $689 .
To ensure t r ouble- f ree operat ion, please observe the following precaut ions: Optical communications are easily affected by external light sources, weak batteries, transfer distance, transf er angle, et c.
Here the settings for the R11 ~ R18 are displayed.
It is possible to select the primary channel mode, secondary channel mode, and the primary channel as well as the secondary channel according to the set t ings of R11 and R12.
$% In order t o conf irm t hat the device is operating cor r ect ly there is an indicate f unct ion inst alled. By looking at t he flash of the LED you can check the st at e of communicat ion.
&' ( ● Serial Port: W hen connecting modems etc. t o the Data Comm unicat ion Eq uipment (DCE) side, connect t he cor responding sig nal nam es of the m odem and IR100S+.
Example Connection Refer ence #2: PC Term inal (DT E) Connection IR100S+ I/F < Cross Cable > PC T erminal(DTE) RxD RxD : Data Receiving (RD) (RD) Only val id wi th receiv ed da ta when the DCD (CD) signal is on. TxD TxD : Data Transmissi on (SD) ( SD) Valid with sending data when RTS (RS) , CTS ( CS), DSR ( DR) , DTR (ER) ar e on.
Product Name: ACT-I R100S Compatibility: Fully compat ible with IrDA -1.0 Physical spec. and IrDA-1 .0 protoco l spec.: IrL AP, IrLM P, IAS, Ti nyTp, IrC OMM Specificat ions of IrDA- 1.
77+9;6? % 60+69>@;+,890 689708+;$0+ )* Many PC peripherals use serial cable to communicate with PC.
"#+ PC#1: I nstall Ir DA Driver. The assigned IR v irt ual port must be COM 4 or less, otherwise HyperTerminal will not be able to connect it IR Monitor: Speed limit = 115.
Communicating with Name: ACT iSYS I R100S- 115 ( Nick name of 100s, might be diff erent with dif fer ent version) Description: I n t ellig ent SIR Adapt er Communication ef ficiency (…) Good at 115.2 Kbps ( or 57. 6 Kbps. Depends on the highest speed both sides can support) 5.
Figure A- 3 Figure A- 4.
Figure A- 5 Figure A- 6.
77+9;6?%$60 . , 2 6;.
"#+ Connect all devices as Fig B-1. PC: Install I r DA Driver. Config ure the Modem: (Fig B-2.
.
.
!.
6& ('%6; 7/7 ..A !" IrLAP, I rLMP, IAS and optional T iny TP, I rCOMM, IrMC, IrTr an- P, etc.
THE FOLLOW ING W ARRANTY GIVES YOU SPECIFIC LEG AL RIGHTS. YOU MAY ALSO HAVE OTHER RI GHTS T HAT VARY FRO M STAT E TO ST ATE. A.
Corpo Corpor .
An important point after buying a device ACTiSYS ACT-IR100S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ACTiSYS ACT-IR100S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ACTiSYS ACT-IR100S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ACTiSYS ACT-IR100S you will learn all the available features of the product, as well as information on its operation. The information that you get ACTiSYS ACT-IR100S will certainly help you make a decision on the purchase.
If you already are a holder of ACTiSYS ACT-IR100S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ACTiSYS ACT-IR100S.
However, one of the most important roles played by the user manual is to help in solving problems with ACTiSYS ACT-IR100S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ACTiSYS ACT-IR100S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
