Instruction/ maintenance manual of the product Start-It Jump 'n Charge VEC012BBD Black & Decker
Go to page of 8
VEC012BBD USER’S MANUAL & W ARRANTY INFORMA TION IMPORT ANT SAFETY INFORMA TION, SA VE THESE INSTRUCTIONS TO REDUCE THE RISK OF INJURY , USER MUST READ AND UNDERST AND THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONT AINS IMPORT ANT INFORMA TION REGARDING THE OPERA TION AND W ARRANTY OF THIS PRODUCT .
iii 8. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low- voltage electrical system other than in a starter-motor application. Do not use the battery charger for charging dry-cell batteries that are commonly used with home appliances.
iv 7. When disconnecting charger , disconnect AC cord, remove clamp from vehicle chassis, and then remove clamp from battery ter minal. 8. Do not charge the battery while the engine is operating. 9. See operating instructions for length of charge information.
3 • Includes non-spillable, maintenance-free, heavy-duty , sealed battery • Rechargeable with either supplied 12 V olt DC Charging Adapter or built-in 120 V olt AC Charger • Heavy duty , industr.
5 USING THE BA TTER Y CHARGER Ensure that all installation and operating instructions, and safety precautions are understood and carefully followed by anyone installing or using the charger . Follow the steps outlined in the “Important Safety Instructions” at the front of this User ’ s Manual.
7 USING THE JUMP-ST ARTER This Jump-Starter is equipped with Good/Bad Polarity Indicators. Energy will only flow when proper connections are made to the batter y and frame. Once the connections are properly made, follow the steps below to jump-start the vehicle.
9 2. Plug the other end of the cord into a standard North American 120 volt AC wall outlet. 3. Charge until the green (FULL) Batter y Status LED Indicator on the front of the unit lights.
11 • If the situation persists after reconditioning and equalizing, we recommend taking your batter y to a cer tified automotive ser vice center for evaluation. F04 — Overtime Condition Appears when charging time exceeds 18 hours. Y ou may be using a charge current rate too low for a large batter y .
An important point after buying a device Black & Decker Start-It Jump 'n Charge VEC012BBD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Black & Decker Start-It Jump 'n Charge VEC012BBD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Black & Decker Start-It Jump 'n Charge VEC012BBD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Black & Decker Start-It Jump 'n Charge VEC012BBD you will learn all the available features of the product, as well as information on its operation. The information that you get Black & Decker Start-It Jump 'n Charge VEC012BBD will certainly help you make a decision on the purchase.
If you already are a holder of Black & Decker Start-It Jump 'n Charge VEC012BBD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Black & Decker Start-It Jump 'n Charge VEC012BBD.
However, one of the most important roles played by the user manual is to help in solving problems with Black & Decker Start-It Jump 'n Charge VEC012BBD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Black & Decker Start-It Jump 'n Charge VEC012BBD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
