Instruction/ maintenance manual of the product ZGF 983 Zanussi
Go to page of 10
NOTICE D'UTILISA TION GEBRUIKSAANWIJZING GEBRAUCHSANLEITUNG INSTRUCTION BOOKLET BE T ABLE DE CUISSON GASKOOKPLAA T GASKOCHMULDE GAS HOB ZGF 983.
33 • This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. • This appliance has been designed for cooking edible foodstuff and to be used for domestic non- professional purposes only.
34 1. Instruction f or the User HOB BURNERS CONTROL KNOBS The hob burners control knobs are situated on the hob front panel. The symbols on the knobs mean that : ● there is no gas supply there is maximum gas supply there is minimum gas supply LIGHTING THE BURNERS • For easier lighting, proceed before putting a pan on the pan support.
35 FO 2347 FO 2032 Fig. 2 Fig. 3 2. Cleaning and Maintenance • Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work.
36 FO 2365 3. T echnical Data Gas Burners Rating Double Crown Burner 3,5 kW Rapid Burner (big) 3 kW (G20) - 2,8 kW (G30-31) Auxiliary Burner (small) 1 kW Semirapid Burner (medium) 2 kW Class 3 Applian.
37 The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
38 INJECTORS REPLACEMENT • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 7), and replace them with the ones required for the type of gas in use (see table 2 ).
39 FITTING THE LID We recommend the lid hinge block are fitted before installing the hob into the worktop. To install the lid onto the hob, proceed as follows: a. Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (fig.
40 INSTALLATION AND ASSEMBLY These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 13. The edge of the cut out must have a minimum distance from the rear wall of 55 mm.
41 480 30 591 380 140 360 cm 2 50 cm 2 120 cm 2 180 cm 2 30 20 min 60 a b POSSIBILITIES FOR INSERTION Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
An important point after buying a device Zanussi ZGF 983 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zanussi ZGF 983 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zanussi ZGF 983 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zanussi ZGF 983 you will learn all the available features of the product, as well as information on its operation. The information that you get Zanussi ZGF 983 will certainly help you make a decision on the purchase.
If you already are a holder of Zanussi ZGF 983, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zanussi ZGF 983.
However, one of the most important roles played by the user manual is to help in solving problems with Zanussi ZGF 983. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zanussi ZGF 983 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
