Instruction/ maintenance manual of the product X906MFE Bertazzoni
Go to page of 20
INSTALLATION, MAINTENANCE AND USE INSTRUCTIONS FOR FREE-STANDING COOKERS 90x60 cm (type M91/M91V) Model X906MFE* , X906 DUAL*, X906GEV* READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE.
2 CONTENTS: INSTALLER TECHNI CAL MANUAL .................................................................................................... ........... pg. 2 Installing the cooker - In stallation in formation .........................................
3 I MPORTANT INFORMATION FOR INS TALLING THE APPLIANC E The cooker can b e installed separatel y, as a freest andi ng u nit, on a plin th (No t suitable for X90 6 GEV* and X90 6 DUAL* models), or bet ween kitchen units or be tween a kitchen unit and the wall.
4 This appliance shall be installed only by authori sed persons and in acco rd ance with the man ufacturer's installation ins tructions, loca l gas fitting regula tions, municipal building codes , electrical wiring regulations, local water supply regulation s, AS/NZS 5601.
5 WARNING: After completing the abo ve-mentioned replacements, t he technician must adju st the burners, as described in the paragraph below, seal any adjustm ent and pre-adjustment de vices and apply the lab el on the appliance, to replace the existing one , corresponding to the ne w gas adjustme nt.
6 WARNING: If the supply cord is dama ged, it must be replaced by the ma nufacturer or its service agent or a similarly qualified pers on in order to av oid a hazard.
7 To replace the power cable, lift the terminal board ’s cover a nd replace the cable. To access the terminal boar d in co okers with a 3x2.5mm² cable, the back panel on the rear of the appliance must be removed.
8 Note: It is recommended not to try to ignite a burner if the relative fl ame cap is not in the correct position. If the flame does not light after the first attempt, wait 5 minutes for the gas to dissipate before attempting to re-light the burner. Tips for using burners correctly: - Use suitable pots for each bur ner (see tab.
9 then release the knob. M ake sure that the burner remains on, other wise repeat the o peration. As for cookers without ignition trough knob, press the thermost at knob a nd the key with the spark sy mbol, wait about 10 seconds after the burner has been completely lit and then rel ease the knob.
10 - the symbol indicates that the electric fan, and the oven light have b een turned on . - the symbol indicates that only the oven light is turned o n; USING THE 5 + 0 SWITCH ( only cooker with Dual Enrgy oven) The 5 + 0 switch installed in th e Dual Energy oven models is used, along with the electric or gas therm ostat.
11 - the symbol indicates that only the top external element (1200W) has been turned on; - the symbol indicates the only the bottom element (1800W ) has been turned on; - the symbol indicates that onl.
12 Before cooking, allow the oven to reach the desired te mperature setting wa iting for the orang e light to turn off. This type of oven is equippe d with a circular elem ent around which a fan has been installed that cr eates forced-air circulation in the horizontal direct ion.
13 Grilling on the shelf : In this case, the shelf supplie d is placed on level 1 or 2 and the foods to be grilled are placed on top, while the tray is insert ed on the lo wer lev els to c ollec t th e cookin g j uice s. T hen turn o n the grill el eme nt s witching the thermostat to the relative position (electric oven version).
14 AFTER-SALES TECHNICAL SE RVICE AND SPARE PARTS TECHNICAL SERVICE AND SPARE PARTS Before leaving the factory, this appliance wa s tested and adjusted by specialist skilled staff to give the best operating results. Any subsequent necessary rep airs or adjustments must be carried out with the greatest care and attention by auth orised personnel.
15 Fig. 1 Fig. 3 Fig. 4 Fig. 5 F i g . 6 F i g . 7.
16 F i g . 8 F i g . 9 Fig.10 Fig.11 Fig 12 Fig 13 Fig. 14.
17 Fig 15 Fig. 16 Fig. 17 T Fig. 18 Fig. 19 Fig. 20 Fig. 21 Fig. 22 Fig. 23 Fig. 24 Fig. 25.
18 Fig. 26 Fig. 27 Fig.28a Fig.28b Fig.28c Fig.28d.
19 Fig. 29 Fig. 30 Fig. 31 Fig. 32.
20 OVERALL DIMENSIONS Cod. 310686.
An important point after buying a device Bertazzoni X906MFE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bertazzoni X906MFE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bertazzoni X906MFE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bertazzoni X906MFE you will learn all the available features of the product, as well as information on its operation. The information that you get Bertazzoni X906MFE will certainly help you make a decision on the purchase.
If you already are a holder of Bertazzoni X906MFE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bertazzoni X906MFE.
However, one of the most important roles played by the user manual is to help in solving problems with Bertazzoni X906MFE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bertazzoni X906MFE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
