Instruction/ maintenance manual of the product S-660TM Weber
Go to page of 32
43267 US 08/06/08 LP G AS GRILL Built-In LP Gas Gr ill Installation Guide #43267 S-460 ™ S-660 ™ YOU MUST READ THIS OWNER’S GUIDE BEFORE OPERATING YOUR GAS GRILL DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames.
2 WWW . WEBER.COM ® D ANGER Failur e to f ollow the Dangers, W arnings and Cautions contained in this Owner’ s Manual may result in ser ious bodily injury or death, or in a fir e or an explosion causing damage to property . W ARNINGS Do not stor e a spare or disconnect ed liquid propane cylinder under or near the barbecue.
3 WWW . WEBER.COM ® 3 GENERAL CONS TRUCTION DET AILS Summit ® Built-In unit and all other accessory units should be on site befor e construction begins. All dimensions hav e a tolerance of plus or minus (+/-) 1 / 4 inch (6.35 mm). The grill frame rests dir ectly on the Island Structure t op finished surface .
4 WWW . WEBER.COM ® OR S-460 ™ S-660 ™ P ARTS LIST Lid - 1 Cookbox - 1 Lid - 1 Cookbox - 1 F ront F rame Rail - 1 Rear F rame Rail - 1 Rear P anel Assembl y - 1 Bott om Shelf - 1 Left Door - 1 Ri.
5 WWW . WEBER.COM ® 5 P ARTS LIST Flav orizer ® Bars - 8 - 12 Stainless Steel Cooking Grat es - 2 - 3 Collection T ra y - 1 Catch-P an Holder - 1 Catch-P an - 1 Disposable Drip P ans - 2 Right F ron.
6 WWW . WEBER.COM ® 1 1 2 2 3 1 2 Arr ow stic ker s on F rame Rail (1) and Lef t Side P anel (2) should point to war d each other (shown abov e). Door St op Brac ket (3) should be positioned as shown (lef t).
7 WWW . WEBER.COM ® 7 3 A TTENTION! Do not fully tighten scr ews. Clips should slide freel y when installed. 4 ASSEMBL Y.
8 WWW . WEBER.COM ® 5 6 Back ASSEMBL Y.
9 WWW . WEBER.COM ® 9 7 ASSEMBL Y.
10 WWW . WEBER.COM ® CA UTION: Use two people to lif t and install the Summit ® Built-In frame assembly . A) Lif t the frame assembly int o the “island” structure opening. Make sure the frame is r esting lev el on the finished surface of the structur e.
11 WWW . WEBER.COM ® 11 9 10 A (1) S-460™ S-660™ A) Apply a bead of silicone sealant (1) around the perimeter and front edges of the grill that are in contact with the “island” structure. This will pre vent moistur e seepage. The sealant you use must ha ve a t emperature rating abov e 120°F (48.
12 WWW . WEBER.COM ® B A TTER Y HOUSING WIRING 1 BLA CK WIRE 2 GREEN WIRE 3 RED WIRE 4 RED WIRE W ARNING: Make sure that all contr ol knobs are tur ned to the OFF position befor e connecting the gas supply and oper ating the grill.
13 WWW . WEBER.COM ® 13 ASSEMBL Y 13 12 (1) (2) (3) Note: Secure wire t o side panel. Requir es 3 “D” alkaline bat teries (Included). Use alk aline bat teries only . Do not mix old and new bat teries or dif ferent types of bat teries (standard, alk aline or rechargeab le).
14 WWW . WEBER.COM ® ASSEMBL Y S-660™ S-460™ 14 16 15 S-660™ S-460™.
15 WWW . WEBER.COM ® 15 S-660™ S-460™ A B C 17 Match Holder ASSEMBL Y.
16 WWW . WEBER.COM ® 18 1/4" (6.35 mm) Drill Bit ASSEMBL Y A TTENTION! Befor e drilling any holes f or the rear v ent make sure the cookbo x is f lush with the front of the gr ill frame.
17 WWW . WEBER.COM ® 17 S-660™ S-460™ 19 ASSEMBL Y 20 S-460 ™ S-660 ™.
18 WWW . WEBER.COM ® S-660™ S-460™ 21 22 S-660 ™ S-460 ™ ASSEMBL Y.
19 WWW . WEBER.COM ® 19 ASSEMBL Y 23 S-660™ S-460™.
20 WWW . WEBER.COM ® 24 S-460 ™ S-660 ™ ASSEMBL Y.
21 WWW . WEBER.COM ® 21 S-660 ™ S-460 ™ S-660 ™ S-460 ™ S-660 ™ + AAA + AAA + AAA 25 - 1 - 2 - 2 - 4 The Weber Grill Out ™ Handle Light has a “Tilt Sensor”: Lid up - ON / Lid Closed - OFF. The power button (a) activates or deactivates the “Tilt Sensor.
22 WWW . WEBER.COM ® TYPIC AL BULK PROP ANE GA S SUPPL Y INST ALLA TION BUIL T -IN G AS LINE L OCA TIONS Note: Leave an access in the “island” structure for g as supply and regulat or ser vice that is not inside the grill structure.
23 WWW . WEBER.COM ® 23 Ta b l e 6.2(a) Maximum Capacity of Metallic Pipe in Cubic F eet of Gas per Hour for Gas P ressures of 2 psi or Less and a Pr essure Dr op of 0.
24 WWW . WEBER.COM ® TYPIC AL 20 LP PROP ANE GA S SUPPL Y INST ALLA TION GAS SUPPL Y The remot e tank enclosure kit pro vide with you grill shall be used f or installations using a 20 lb LP cylinder , mounted in an “island” str ucture .
25 WWW . WEBER.COM ® 25 OPERA TING W ARNING: Only use the W eber ® T ank Enc losure Kit outdoors in a well-v entilated ar ea. Do not use in a garage, building, breezew ay or any other enc losed area. W ARNING: Y our W eber ® T ank Enclosure Kit shall not be used under an unprot ected combustib le roof or o ver hang.
26 WWW . WEBER.COM ® L OCA TING Y OUR LP T ANK ENCLOSURE KIT When det er mining a suitab le location for your LP T ank Enclosur e Kit installation, give at tention to concerns such as pro ximity to traf fic paths, and k eeping any gas suppl y lines as shor t as possible .
27 WWW . WEBER.COM ® 27 2 4 8 4 2 4 2 2 P ARTS LIST Hose and regulat or - 1 T ank stand - 1 T ank stand base - 1 T ank Scale - 1 1/4-20 nut - 6 Nylon washer - 1 2 1/4-20 x 1/2” bolt - 6 Cylinder gl.
28 WWW . WEBER.COM ® 3 4 MOUNTING THE LP T ANK BRA CKET Mount the LP tank brac ket to the right hand side of the enclosure opening using non corr osive har dware . Mounting holes are pro vided on the sides and bott om of your LP tank brac ket. Be sure t o mount the brack et securley to the enclosure bef ore use.
29 WWW . WEBER.COM ® 29 A B C D E i ii iv v CONNECT GA S SUPPL Y A 58 inch (1 47 .32 cm) corr ugat ed gas line is supplied with the grill. This line needs t o pass through the g as inlet opening to the main gas suppl y . 1) Connect the corrugat ed gas line to the manif old located on the right hand side of grill under the control panel.
30 WWW . WEBER.COM ® VENTILA TION W ARNING: V entillation holes must be pro vided in the struct ure at the t op and bott om to pro vide ventilation in the ev ent of a gas leak.
31 31 NO TES.
©2009 The follo wing trademarks are regist ered in the name of Weber -Stephen P roducts Co ., an Illinois cor poration, located at 200 East D aniels Road, P alatine, Illinois 60067 U .
An important point after buying a device Weber S-660TM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Weber S-660TM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Weber S-660TM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Weber S-660TM you will learn all the available features of the product, as well as information on its operation. The information that you get Weber S-660TM will certainly help you make a decision on the purchase.
If you already are a holder of Weber S-660TM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Weber S-660TM.
However, one of the most important roles played by the user manual is to help in solving problems with Weber S-660TM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Weber S-660TM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center