Instruction/ maintenance manual of the product Max Audio MX5000A Waves
Go to page of 9
Preliminary MX5000A Development System Manual 1 System Overview The MX5000A Development System allows manufacturers to easily evaluate and prototype system improvements by adding MaxxAudio psyc ho-acoustic processing to existing audio systems.
Preliminary 2 Input/Output and Power Connections Connect Inputs, Outputs, Powe r and Ground as described below. Please see Figures 2 and 3 for additional illustrations. Connect Inputs • Three sets of stereo input s are provided. Located on t he bottom edge of the PCB, these are labeled as LI1/RI1, LI2/RI2, and LI3/RI 3.
Preliminary Figure 2. MX5000 Prot otype Module Close-up Figure 3. Connections for MX5000 Prototype Module MX5000A Development System January 2007.
Preliminary 3 Controls The MX5000 Prototyping Module supports two different control options. a) I 2 C Slave Mode b) I 2 C Host Mode 3.1 I 2 C Slave Mode Controls In addition to the MX5000 Prototyping Modul e, the MX5000A Development System is supplied with a Telos USB to I 2 C Emulator.
Preliminary 3.2 Graphic User Interface The GUI for the MX5000 Prototyping Module is shown in Figure 5. Figure 5. MX5000A GUI MX5000A Development System January 2007.
Preliminary 3.3 Digital Audio Input/Ouput For digital audio I/O, the system supports thr ee stereo inputs and two stereo outputs as shown in Table 1. All inputs and outputs are synchronous with shared clock and synch pins. The digital audio input/output is supported only in I 2 C Slave Mode of the MX5000A.
Preliminary Figure 6. MX5000A Protot yping Module Layout Full schematics, bill of materials, and layout files for this system is available to customers.
Preliminary 3.4 I 2 C Host Mode Controls In I 2 C Host Mode, the MX5000 will r ead audio parameters fr om the external serial flash ROM after reset. After re set, the system will continuously moni tor the value of external analog control pins for real-time audio controls.
Preliminary 5 Ordering Part Numbers MX5000ADS For MX5000A Development System Includes: MX5000A Prototyping Module (MX5000APM) Telos Connii or Connii MM with software Waves Control GUI software 4 wire cable – Telos connector to I 2 C header Note: ‘A’ in MX5000A refers to hardw are/software version of the MX5000.
An important point after buying a device Waves Max Audio MX5000A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Waves Max Audio MX5000A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Waves Max Audio MX5000A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Waves Max Audio MX5000A you will learn all the available features of the product, as well as information on its operation. The information that you get Waves Max Audio MX5000A will certainly help you make a decision on the purchase.
If you already are a holder of Waves Max Audio MX5000A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Waves Max Audio MX5000A.
However, one of the most important roles played by the user manual is to help in solving problems with Waves Max Audio MX5000A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Waves Max Audio MX5000A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
