Instruction/ maintenance manual of the product UDW-10003 Uniden
Go to page of 24
UDW-10003 Video Surveillance System User’s Manual What’s in the Box Portable receiver with 3-inch color LCD display Portable video camera Camera stand Two AC adapters Software CD AV cable USB cable If any items are missing or damaged, contact our Customer Care Line immediately.
Important Safety Instructions! This manual contains important information about this product’s operation. If you are installing this product for others, you must leave this manual or a copy with the end user.
Contents Important Safety Instructions! ........2 Warnings to Parents and Other Users .................................................... 2 For best results: .................................... 3 Getting Started .................................4 Connect the Power .
4 Getting Started Connect the Power Connect one AC adapter to the camera’s power input and the other to the receiver’s power input. (The two adapters are exactly the same.) Connect the other end of each adapter to a standard 120 volt AC indoor outlet.
5 Check the Video Signal As soon as the receiver powers on, it detects the camera and shows the video on the display. The icons at the top of the screen tell you what’s going on with the camera and receiver. The table below shows the different status icons and what they mean.
6 Learning Your System Get to Know the Camera What the buttons do Button What it does POWER Turn the camera on. Press and hold to turn it off. LINK Enter pairing mode. What the lights mean Power Status light State What it means On The camera is on. Off The camera is off.
7 Using the camera mount The camera has a built-in stand so you can place it on any flat surface. If you want to place your camera on a wall or a ceiling (or even if you just want to secure it to a flat surface), you can use the included camera mount.
8 Get to Know the Receiver What the buttons do Button What it does MENU/OK Open and close the menu - LEFT In zoom mode: pan to the left side of the zoom area. In the menu: cycle through the available options for the selected menu item. In quad display: go to channel 4.
9 Button What it does DOWN In zoom mode: pan to the bottom of the zoom area. In the menu: move the cursor down one line. In quad display: go to channel 2. - - - SELECT CAMERA Cycle through the active cameras. From the pairing menu: link to the selected camera.
10 Using the Menu Item Use it to Audio Vol Adjust the volume of the audio from the camera. Choose a value from 0 (off) through 20 (maximum). Scan Time Set the length of time the receiver spends on each active camera during a scan (see page 15) or activate quad display (see page 16).
11 Using Zoom Mode The receiver can zoom in so you can see the video better. In zoom mode, the receiver increases the pixel size and focuses on the center of the picture.
12 Connecting to Your TV You can connect the receiver to any standard television with RCA composite video inputs. To use bandwidth efficiently, the system compresses the video signal using Motion-JPEG; the system then digitizes the signal before transmitting it to provide a secure video link.
13 Multiple Camera Features Your receiver supports a total of four active cameras at a time. You can mix and match any of the accessory cameras. (See our website for compatible camera options.) Pairing Cameras Pairing is like introducing the camera and the receiver so they can communicate.
14 Changing to a Dierent Camera On the receiver, press to cycle through the enabled channels from CAM1 through CAM4 . After the last enabled channel, the receiver goes back to the first camera. Each time you press , the receiver goes to the next enabled channel, regardless of whether there is a camera present on that channel.
15 Setting Up a Scan You can have the receiver automatically cycle through the enabled channels. Open the menu, and scroll down to select Scan time . Use RIGHT or LEFT to select the amount of time you want the receiver to stay on each camera. Choose 5 seconds , 10 seconds , 15 seconds , or 20 seconds .
16 Using Quad Display In quad display, the receiver puts all four channels on the screen at the same time. The channels appear in the positions shown to the right: If a channel is disabled or there is no signal from the camera, that channel's section of the quad display will be blank.
17 Solving Problems If you have any trouble with your system, try these simple steps first. If you still have a question, call our Customer Care Line listed on the front cover. If… Try.. The image on the display is too bright. Adjusting the brightness on the receiver (in the System Setup sub- menu).
18 If… Try.. None of the buttons on the receiver respond when I press them. Resetting the receiver. - Unstable or Weak Signal If the video seems to lag and or the audio sounds weak, the camera and the receiver do not have a strong, clear signal between them.
19 Signal Level Icon Data Rate (kbps) Frames per second (approx) QVGA (Zoom) VGA (Normal) Perfect 1062~1280 15~20 5~10 Good 725~1062 12~16 3~5 Fair 543~725 8~12 2~4 Low 250~543 0~5 0~1 Zero 0~250 0 0 If the suggestions above don’t provide enough improvement in the the signal quality, you may want to run the camera at QVGA or zoom mode.
20 If the static is only on 1 camera If the static is on all cameras Check near the camera for one of the common interference sources. Try moving the camera away from a suspected source, or try moving the suspected source so it’s not between the camera and the receiver.
21 Additional Information Product Specications Radio Frequency Transceiver RF Frequency 2402 Mhz ~ 2483.5 Mhz Modulation GFSK Spread spectrum Frequency Hopping Anti Interference Clean Channel Dynam.
22 System Specifications Camera Receiver Low light solution 11 IR LEDs, 1 Low light sensor Low light sensitivity 1-8 lux Picture sensor OV7725 1/4’ Color CMOS Lens F3.
23 FCC Compliance Information Part 15 Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
One-year Limited Warranty Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one.
An important point after buying a device Uniden UDW-10003 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Uniden UDW-10003 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Uniden UDW-10003 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Uniden UDW-10003 you will learn all the available features of the product, as well as information on its operation. The information that you get Uniden UDW-10003 will certainly help you make a decision on the purchase.
If you already are a holder of Uniden UDW-10003, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Uniden UDW-10003.
However, one of the most important roles played by the user manual is to help in solving problems with Uniden UDW-10003. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Uniden UDW-10003 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center