Instruction/ maintenance manual of the product S1471 TYAN
Go to page of 41
TYAN S1471 Pentium Class 75 thru 200MHz 430VX PCI-ISA System Board User's Manual Revision 1.0.
2 S1471-001-01 http://www.tyan.com Table Of Contents 1. Introduction....................................................................... 3 1.1 Overview................................................................3 1.2 Hardware Specifications....
3 S1471-001-01 http://www.tyan.com 1. Introduction 1.1 Overview The S1471 is a quality, high performance mainboard designed forl Intel Pentium microprocessors. This mainboard utilizes the Intel 430VX chipset and can support CPU speeds of 75MHz through 200MHz.
4 S1471-001-01 http://www.tyan.com 1.2 Hardware Specifications/Features w CPU Intel Pentium 75 MHz thru 200 MHz (Socket 7) Intel Pentium P55C Cyrix/IBM/SGS M1/6x86 P120, P150 & P166 w Speed 50/60/66 MHz system bus 25/30/33 MHz PCI bus 7.5/8.33 MHz ISA bus speed w DRAM 2 banks of 72 pin SIMM and 2 DIMM Banks Supports 5V or 3.
5 S1471-001-01 http://www.tyan.com w Mouse On-board PS/2 mouse connector. 1.3 Software Specifications w BIOS Award or AMI BIOS A T CMOS setup, BIOS/CHIPSET setup, and hard disk utility included. Support for easy BIOS upgrades with flash EPROM chip. w O.
6 S1471-001-01 http://www.tyan.com 2. Board Installation 2.1 Unpacking The mainboard package should contain the following: w S1471 Mainboard w One IDE 40 pin cables w Two serial cables w w One paralle.
7 S1471-001-01 http://www.tyan.com 3. On Board Resource Setting Figure 3.1 S1471 Board Layout KB CTR PWR CON. 5V ISA Slot 1 ISA Slot 2 ISA Slot 3 ISA Slot 4 Keyboard CON BIOS AMI/AWARD RTC PS/2 Mouse .
8 S1471-001-01 http://www.tyan.com 3.2 Jumper Settings CPU Speed Settings for Pentium P54C and P55C: J15 J40 J39 CPU Speed 1-2, 3-4 Off Off 75 MHz 3-4 Off Off 90 MHz 1-2 Off Off 100 MHz 3-4 On Off 120.
9 S1471-001-01 http://www.tyan.com Memory Voltage SIMMs: Some EDO memory uses 3.3 V . Damage to system can result if these are set incorrectly! Volts J5 J7 J9 J11 J3 J6 J8 Default 5V On On On On Off Off Off 3.3V Off Off Off Off On On On Memory Voltage DIMMs: Default is 5 V .
10 S1471-001-01 http://www.tyan.com Reset Connector: J41 Pinout Assignment 1 Power Good 2 Ground Turbo LED Connector: J48 Pinout Assignment 1 Cathode 2 Anode Flash EPROM: J50 This jumper should be left at the factory default.
11 S1471-001-01 http://www.tyan.com Infra Red Interface: Con9 and Con10 Pinout Assignment 1 Signal In 2 Gnd 3 Signal Out 4 VCC I/O Port Setting: J13 and J14 J13 J14 Default For Serial Port 1-2 1-2 For.
12 S1471-001-01 http://www.tyan.com 3.3 CMOS RTC CMOS RTC includes an internal battery and Real Time Clock circuit. It provides the date and the time for the system. Normally the life span of a RTC internal battery is 10 years. When replacing, you should use the same model.
13 S1471-001-01 http://www.tyan.com 3.7 Hardware Reset Switch Connector Installation The RESET switch on your cases' display panel provides users with the HARD WARE RESET functinon which is the same as power on/off. The system will do a cold start after the RESET switch is pushed by the user.
14 S1471-001-01 http://www.tyan.com 3.9DRAM Installation The S1471 uses a 64-bit data path from memory to CPU and can accommodate up to 128 MB of RAM. The mainboard supports Fast Page Mode, and EDO (Extended Data Out) 72 pin SIMMs. SDRAM(Synchronous) are also supported in the DIMM slots.
15 S1471-001-01 http://www.tyan.com 1. Make sure the ZIF socket lever is up. To raise the lever, pull it out to the side a little and raise it as far as it will go. The top plate will slide back. 2. Align the CPU and socket Pin 1 corners. The pins on the bottom should align with the rows of holes in the socket.
16 S1471-001-01 http://www.tyan.com 3.11 Upgrading Cache Memory The S1471 has either 256Kb or 512kb of on-board pipelined burst SRAM. Since the SRAM is surfaced mounted onto the board, the L2 Cache cannot be field upgraded.
17 S1471-001-01 http://www.tyan.com 3.13 Connecting the Power Supply The system power supply connectors on the mainboard is for a 5 volt power supply. Incorrect installation of the power supply could result in serious damage to the system board and connected peripherals.
18 S1471-001-01 http://www.tyan.com Align the plastic guide pins on the lead cables to their receptacles on the mainboard. Y ou may need to hold the lead at an angle to line it up.Once you have the guide pins aligned, press the lead connector so that the plastic clips on the lead snap into place and secure the lead to the connec- tor.
19 S1471-001-01 http://www.tyan.com 4. BIOS Configuration Award's BIOS has a built in setup program that allows the user to modify the basic system configuration. This type of information is stored in the battery-backed CMOS SRAM. Entering incorrect information or forget- ting your password can lock you out of your system.
20 S1471-001-01 http://www.tyan.com 4.2. Control Keys PgUp key Increases the numeric value or make changes PgDn key Decreases the numeric value or make changes F1 key General help, only for Status Pag.
21 S1471-001-01 http://www.tyan.com 4.3. Getting Help 4.3.1. Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen.
22 S1471-001-01 http://www.tyan.com w w Standard CMOS setup This setup page includes all the items in a standard compatible BIOS. w w BIOS features setup This setup page includes all of the enhanced features of Award's BIOS. w w Chipset features setup This setup page includes all the items of the 430HX chipset features.
23 S1471-001-01 http://www.tyan.com w w Date The date format is <month>, <day>, <year>. Press <F3> to show the calendar. Base Memory: 640 K Extended Memory: 7168 K Expanded Mem.
24 S1471-001-01 http://www.tyan.com None No floppy drive installed 360K, 5.25 in. 5-1/4 inch PC-type standard drive; 360 kilobyte capacity 1.2M,5.25 in. 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity 720K, 3.5 in. 3-1/2 inch double-sided drive; 720 kilobyte capacity 1.
25 S1471-001-01 http://www.tyan.com w w Video This category detects the type of graphics adapter used for the primary display system. It must match your video display card and monitor. Al- though secondary monitors are supported, you do not have to select that type in setup.
26 S1471-001-01 http://www.tyan.com Expanded Memory Expanded Memory (EMS) defines a 64Kb page frame in the area between 640K and 1Mb containing four 16K pages that are windows into the EMS memory. Programs issue requests to the EMS manager to switch the page to any part of EMS memory.
27 S1471-001-01 http://www.tyan.com w w Virus warning This category flashes on screen. During and after the system boot up, any attempt to write to the boot sector or the partition table of the hard disk drive will halt the system and the following error message will appear.
28 S1471-001-01 http://www.tyan.com w w Boot Up Floppy Seek During POST, the BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 720K, 1.2M and 1.44M are all 80 tracks. Default value is Enabled Enabled BIOS searches for floppy disk drive to determind if it is 40 or 80 tracks.
29 S1471-001-01 http://www.tyan.com ROM ISA BIOS CHIPSET SETUP UTILITY AWARD SOFTWARE, INC. Auto Configuration :Enabled DRAM Timing :70ns DRAM RAS# Precharge Time :3 DRAM R/W Leadoff Timing :6 DRAM RA.
30 S1471-001-01 http://www.tyan.com 4.7.1 Power Management Setup ROM ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC Power Management :Disabled IRQ3 (Com2) :Off PM Control By APM :No IRQ4 (Com1) :.
31 S1471-001-01 http://www.tyan.com w w Doze Mode Defines the continous idle time before the system enters Doze mode. w w Standby Mode Defines the continous idle time before the system enters Standby mode. w w Power Down Activities Defines the the activities that can cause the PM timers to reload.
32 S1471-001-01 http://www.tyan.com 4.8 PCI Slot Configuration ROM ISA BIOS PCI SLOT CONFIGUR A TION AW ARD SOFT WARE, INC. Resource Controlled by :Manual Reset Configuration :Disabled IRQ3 assigned t.
33 S1471-001-01 http://www.tyan.com w w Resources Controlled By The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible devices. If you seelect Auto, all the interrupt request and DMA assignment fields disappear, as the BIOS automatically assigns them.
34 S1471-001-01 http://www.tyan.com 4.9 Integrated Peripherals Integrated Peripherals Award Software, Inc. IDE HDD Block Mode :Enabled IDE Primary Master PIO :Auto IDE Primary Slave PIO :Auto IDE Seco.
35 S1471-001-01 http://www.tyan.com STANDARD CMOS SETUP PASSWORD SETTING BIOS FE A TURES SETUP IDE HDD AUTO DETECTION CHIPSET FE ATURES SETUP DAVE & EXIT SETUP PCI SLOT configuration EXIT WITH OUT S AVING LOAD SETUP DEFAU L TS 4.9. LOAD SETUP DE FAULTS ROM ISA BIOS CMOS SETUP UTILITY AWARD SOFT W ARE INC.
36 S1471-001-01 http://www.tyan.com ROM ISA BIOS CMOS SETUP UTILITY AW ARD SOFT WARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FE A TURES SETUP IDE HDD AUTO DETECTION CHIPSET FE ATURES SETUP DAV.
37 S1471-001-01 http://www.tyan.com 4.11. IDE HDD AUTO DETECTION ROM ISA BIOS CMOS SETUP UTILITY AW ARD SOFT WARE, INC. CYLS. HEAD PRECOMP LANZONE SECTORS Drive C: (202 Mb) 989 12 65535 989 35 Do you want to accept this as drive C (Y/N)? Esc:Skip Type "Y" to accept the H.
38 S1471-001-01 http://www.tyan.com 5.0 Flash Writer Utility Warning: Do not flash the BIOS unless instructed by your deale r . Y ou can upgrade the BIOS of your mainboard by using a "Flash Memory Writer"(FMW) utilit y . This utility can be downloaded from Tyan's BBS(Consult your system vendor for the phone #) or web site.
39 S1471-001-01 http://www.tyan.com To reprogram the System BIOS, you must first do the following: 1. Check jumper J50.(Default pins 1-2) The S1471 uses a 5V Flash EPROM so jumper J50 should be left in the default postion on pins 1 and 2. This jumper should never be moved.
40 S1471-001-01 http://www.tyan.com Once you have satisfied the two requirements mentioned above, you can run FM W . You can copy the contents of the “Flash” directory to your hard drive, or you can run the utility from a backup of the support floppy disk.
41 S1471-001-01 http://www.tyan.com 6.0 System Resource 6.1. TIMER & DMA CHANNEL MAP TIMER MAP: TIMER Channel-0 system timer interrupt TIMER Channel-1 DRAM REFRESH request TIMER Channel-2 SPEAKER .
An important point after buying a device TYAN TYAN S1471 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TYAN TYAN S1471 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TYAN TYAN S1471 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TYAN TYAN S1471 you will learn all the available features of the product, as well as information on its operation. The information that you get TYAN TYAN S1471 will certainly help you make a decision on the purchase.
If you already are a holder of TYAN TYAN S1471, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TYAN TYAN S1471.
However, one of the most important roles played by the user manual is to help in solving problems with TYAN TYAN S1471. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TYAN TYAN S1471 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
