Instruction/ maintenance manual of the product SD-M2012C Toshiba
Go to page of 16
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-M2012C D VD-R OM DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the D VD- R OM Drive .......................
1 INTR ODUCTION – SD-M2012C D VD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (ej ect button, software, emergency eject hole ) Average Random Access Time CD-ROM 110ms CD-RW 170.
CD • CD-D A • CD+(E)G • CD-MIDI • CD-TEXT • CD-R OM • CD-ROM-XA • CD-I Bridge (Photo-CD , Video CD) • CD-I • Multi-session (Photo-CD , CD Extra, CD-RW , CD-R) • CD-R (Read) • CD-RW (Read) Front Panel Figure 1.SD-M2012C DVD-ROM Drive Front Pan el Loading Tray Load disc using tray.
3 SETUP – SD-M2012C D VD-ROM The following steps must be performe d to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable (o ptional) • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pi n s located on the rear of the DVD-ROM drive.
4 Placing DVD-ROM Drive inside your Computer Now that you have set the jumpers, you are read y to install your DVD- ROM drive inside your com puter. Important Note: Disconnect power fr om your co mputer system before b eginning installation. Remove computer co ver and faceplate if required.
5 Audio Cable (optional) - If you have a sound card and speakers, and would like t o play audio CDs on your computer, you will need to install a CD/DVD audio ca ble. Toshiba's DVD-ROM dri ves use a standard 4-pin audio cable that can be purchased from mo st local computer suppliers.
6 USING THE D VD D VD-R OM Drive – SD-M2012C Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
7 Removing a Disc To remove a disc from the DVD-RO M drive, perform the following steps: 1. Open the Loading T r ay by pressing the Eject Button. 2. Grasp disc by edges , and lift out of loading tra y . 3. Press Eject Button again to close Loading T ray .
8 NOTE: Use a bar that is less than 1.5 mm in diameter . Do not insert more than 50mm in depth. Inserting more than 50mm may damag e the DVD-ROM drive. Handling Media DVD media is sensitive to dust and fingerprints. Carefully han dle media by its edges only.
9 TR OUBLESHOO TING – SD-M2012C Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instructi ons to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
10 SPECIFICA TIONS –SD-M2012C General Interface ATAPI Media Compatibility CD 120mm CD-ROM (Read Only) 80mm CD (Horizontal Mount Only) 800/700/650/550MB CD-Recordab le (Read) 80mm CD- Recordab le (Re.
11 Burst Rate 16.7 Mbyte/s (PIO Mode 4) 16.7 Mbyte/s (multiple word DMA tr ansf er mode 2) 33.3 MByte/s (Ultra DMA) Random Access Time CD-ROM 110ms CD-RW 170ms DVD-Single 110ms DVD-Dual 150ms DVD-RAM .
12 Power Consumption DC Voltage and Current Requireme nts 5V / 1.5A, 12V ; 1.5A +5V +12V Sleep Standby 400mA 500mA 100mA 300mA Physical Height 1.65" (42mm) Width 5.
13 DRIVE CONNECT ORS –SD-M2012C Figure 1.SD-M2012C DVD-ROM Dr ive Rear Panel - Connectors Po w e r Connector P ower is supplie d to your D VD -ROM dr ive b y t he connection with your co mputer's +5V/+12V pow er cabl e to the pow er soc ket at the back of drive .
14 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
An important point after buying a device Toshiba SD-M2012C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba SD-M2012C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba SD-M2012C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba SD-M2012C you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba SD-M2012C will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba SD-M2012C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba SD-M2012C.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba SD-M2012C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba SD-M2012C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
