Instruction/ maintenance manual of the product C-CC714 NT TOA Electronics
Go to page of 32
Thank you for purchasing TOA’s Outdoor Combination Camera. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
2 T ABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 5 3. FEA TURES ..........
3 1. SAFETY PRECAUTIONS • Be sure to read the instructions in this section carefully before use. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.
4 When Installing the Unit • Avoid installing the unit in locations exposed to sea breeze or corrosive gas. Mounts may become corroded, eventually causing the unit to fall off, which could result in personal injury. • Do not mount the unit in locations exposed to constant vibration.
5 2. GENERAL DESCRIPTION TOA’s dome-type color cameras combine with a high-speed camera drive that permits one 360-degree horizontal rotation per second and a 22 times (C-CC714) or a 23 times (C-CC764) optical zoom lens. Up to 255 arbitrary positions can be preset and such preset positions can be instantaneously repeated.
6 4. HANDLING PRECAUTIONS • Noise may appear on the monitor or preset camera positions may deviate with prolonged camera use. In such cases, use the camera’s refresh function to automatically refresh settings and reestablish the home position once a day or week, thus allowing any position deviation to be corrected.
7 • The dome camera features built-in heat generating circuitry. Take care not to touch the internal parts marked “Caution! High Temperature” when working inside the camera during dome cleaning or maintenance .
8 1 2 3 4 5 6 [ Housing Appearance ] 13 14 15 16 18 19 17 20 19 10 12 9 9 9 9 11 11 7 8 9 9 [ Housing Bottom ] [ Camera Unit Top ] [ Camera Unit Bottom ] 5.
(1) Top cover (2) Safety wire for housing (3) Housing adaptor (4) Safety screw (5) Dome cover (6) Decorative frame (7) Sunshade (Outside) (8) Case (Inside) (9) Hexagon sleeve (10) Safety wire for dome.
10 6.1. Precautions When Installing the Camera • Insulate the joint of the camera video output cable and the coaxial cable from other equipment by wrapping the (vinyl) insulating tape around it. Also, install such cables taking care that they do not contact metal stuff close to them.
11 GND GND Connect to the next cameraʼs terminal Camera control cable Camera control cable Shield twisted pair cable Connect to remote controller ʼs camera control terminal 6.
7.3.1. Camera Address Setting Switch (DIP Switch 1: No. 1 – 8) Used to set camera address when using the camera in connection with the C-RM500 Remote Controller. Set the DIP switch so that the address is equal to the connected switcher's channel number.
13 7.3.5. Termination Switch (DIP switch 2: No. 8) Set the switch of the camera last connected to the RS-485 communications line to ON. (Factory setting: OFF) 7.3.2. Communication Speed Setting Switch (DIP switch 2: No. 1 – 2) Check to be sure that the communication speed set here is the same as that of the Remote Controller.
14 ON 12345678 11 7 3 3 4 9 ON 12345678 ON 12345678 ON 12345678 ON 12345678 21 8 3 4 5 0 ON 12345678 ON 12345678 ON 12345678 ON 12345678 31 9 3 5 5 1 ON 12345678 ON 12345678 ON 12345678 ON 12345678 42.
15 ON 12345678 65 81 97 1 13 ON 12345678 ON 12345678 ON 12345678 ON 12345678 66 82 98 1 14 ON 12345678 ON 12345678 ON 12345678 ON 12345678 67 83 99 1 15 ON 12345678 ON 12345678 ON 12345678 ON 12345678.
16 ON 12345678 129 145 161 177 ON 12345678 ON 12345678 ON 12345678 ON 12345678 130 146 162 178 ON 12345678 ON 12345678 ON 12345678 ON 12345678 131 147 163 179 ON 12345678 ON 12345678 ON 12345678 ON 12.
17 ON 12345678 193 209 225 241 ON 12345678 ON 12345678 ON 12345678 ON 12345678 194 210 226 242 ON 12345678 ON 12345678 ON 12345678 ON 12345678 195 21 1 227 243 ON 12345678 ON 12345678 ON 12345678 ON 1.
18 8.1. About Installation • Mount the camera to a heavy-duty wall surface using the optional C-BC711W Wall Mounting Bracket. • When installing the camera on a pole, use the optional C-BC711W Wall Mounting Bracket, C-BC711PM Pole Mounting Bracket and 2 YS-60B Mounting Bands in combination.
19 8.3. W all Mounting Bracket Installation Use the optional C-BC711W Wall Mounting Bracket. Notes • Check to be sure that wall surface can structurally support the weight of the camera and mounting bracket • Bolts, nuts and washers are not supplied with the bracket.
20 8.4. Attaching Housing and Camera Unit to W all Mounting Bracket 1. Loosen 2 safety screws. 2. Run the safety wire through the top cover, then hang the hook to the mounting bracket.
21 5. Using the 3 supplied camera mounting screws M5 x 12, attach the housing unit to pipe. Tighten 3 screws equally and ensure that no parts rattle. Note: In this event, tighten screws while pressing the housing against the pipe. 4. After confirming the housing direction, push the housing up, then tighten 2 safety screws.
22 7. Connect the safety wire to the housing projection, then attach the camera unit. Note: Align mark of the camera unit with that of the housing when attaching the camera unit to the housing. Hang the safety wire. Safety wire mark 6. Using the supplied 3 hexagon socket screws, attach the top cover 1 to the housing.
23 8. Make the camera unit in horizontal position and push it straight up closely to the housing. Cross sectional view of the housing Camera unit 1 2 mark Duct Note Insert the camera unit in an oblique direction in the order of 1 to 2 keeping away from the duct of the housing.
24 Safety wire protrudes from the compartment. Safety wire does not protrude from the compartment. Note When mounting the camera unit to the housing, mount it straight till it is attached to the housing correctly. Mounting it at an angle may cause damage to the camera unit.
25 10. Tighten 2 camera unit mounting screws to attach the camera unit to the base unit. Camera unit mounting screw Camera unit mounting screw 11. Attach the dome cover. Slide down the dome cover’s screw head through the housing suspension fitting’s slot.
26 13. Tighten 4 screws equally to attach the dome cover to the housing and ensure that the dome cover does not rattle. 12. Align the dome cover’s 4 screws with the hexagon head sleeves inside the housing.
27 8.5. Pole Mounting Bracket Installation The optional C-BC711PM Pole Mounting Bracket, C-BC711W Wall Mounting Bracket and YS-60B Mounting Band are required to mount the camera on a pole. Note Those mounting brackets and band can be installed on a pole having a mounting pipe diameter of 90 - 340 mm.
28 8.6. Suspension Bracket Installation The C-BC711P Suspension Bracket is required to suspend the camera from a ceiling. Note Mount the bracket to a concrete wall or robustly constructed wall surface that can sufficiently withstand the weight of the units.
29 [ RS-485 Communications line control ] Combination camera Multi-switcher Monitor TV Outdoor combination camera Dedicated Remote controller Note Combination cameras and outdoor combination cameras can be used in free combinations.
30 C-CC764 NT C-CC764 PL 24 V AC, 50/ 60 Hz (2P loose end) 10 W (normal operation), 80 W max. RS-485 communications system (new protocol compatible) VBS 1.
31 C-CC714 NT C-CC714 PL 24 V AC, 50/ 60 Hz (2P loose end) 10 W (normal operation), 80 W max. RS-485 communications system (new protocol compatible) VBS 1.
• Accessories CD-R (CAMARA CONTROLLER Software, installation manual) ...... 1 Hexagon socket screw M4 x 8 ...........................................
An important point after buying a device TOA Electronics C-CC714 NT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics C-CC714 NT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics C-CC714 NT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics C-CC714 NT you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics C-CC714 NT will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics C-CC714 NT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics C-CC714 NT.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics C-CC714 NT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics C-CC714 NT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
