Instruction/ maintenance manual of the product U140E116-02 Bay Technical Associates
Go to page of 27
1 OWNER'S MANUAL ________________ V93A DAC: 14.4k bps HOST COMMUNICATION MODEM MODULE FOR BAYTECH M-SERIES DAC BayTech Manual Publication #U140E116-02.
2 FCC REQUIREMENTS FOR THE V93A HOST COMMUNICATION MODEM MODULE 1. The Federal Communications Commission (FCC) has established rules which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connections.
3 The ringer equivalence number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly.
4 TABLE OF CONTENTS 1 GENERAL INFORMATION ............................................................................................................... 6 2 SPECIFICATIONS ..............................................................................
5 .7 LOGIN PASSWORD ................................................................................................................. 21 .8 LOCAL MODEM SETUP .............................................................................................
6 1 GENERAL INFORMATION The V93A Host Communication Modem Module is the remote user interface to the BayTech M Series DAC (Data Acquisition and Control) units.
7 2 SPECIFICATIONS INTERFACE: Dial-up telephone line MODULATION: V.32bis (14,400 bps) or V.32 (9600 bps) COMPRESSION: V.42bis, MNP5 CONNECTORS: 2 x 4-pin modular MODULE LEDS: TD (Transmit Data), RD (Receive Data), CD (Carrier Detect), MR (Modem Ready), and CX (Connection) status LEDs.
8 3 SOFTWARE UTILITY DISKETTE IMPORTANT: Copy the BayTech original diskette onto a blank diskette and store the original in a safe place. BayTech provides utility software for DOS compatible PCs to assist you in configuring your M-Series DAC unit. This diskette contains several programs, however the only programs that will be used is TERM.
9 Figure 1 shows the required adapter for a PC with a DB-25 connector. Use a crossed RJ-45 cable to connect these adapters to the EIA-232 port. BLUE ORANGE BLACK RED GREEN YELLOW BROWN GRAY 1 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 TX RX RTS CTS DSR GND DCD DTR FEMALE DE-9 RJ-45 Figure 1: PC, PS/2 Computer/Terminal Adapter BayTech Part No.
10 GRAY BROWN YELLOW GREEN RED BLACK ORANGE BLUE RJ-45 FEMALE DB-25 CTS TX DSR GND DTR DCD RX RTS 2 3 4 5 6 7 8 20 8 7 6 5 4 3 2 1 Figure 2: PC, PS/2 Computer/Terminal Adapter BayTech Part No. 25FRJ45PC-3 IMPORTANT : When modular connectors are used as shown in Figures 1 - 2 above with RJ-45 connectors, crossed RJ-45 cables are required.
11 .2 MODEM CONNECTION Connect the phone line to the RJ-11 connector on the V93A with a RJ-11 cable. 5 OPERATION a. You are ready to perform commands when a terminal or PC is communicating with: (1) the V93A's EIA-232 port. (2) a remote modem is communicating with the V93A’s modem.
12 Unit 2 Module 1 REV. 4.XX Copyright (c) 1995-1997 Bay Technical Associates To login, enter password Login: BTA (default) You will be prompted to type in the desired password followed by <ENTER> when a connection to the V93A modem is first made.
13 Device B (2,2)............2 Device C (2,3)............3 Device D (2,4)............4 Configure.........................C Manual Mode.......................M Exit..............................X Unit Reset........................R Logout..............
14 By responding to the Enter Request : message at the end of the V93A menu with “M” you receive a response similar to the following: Device A (2,1).................... 1 Device B (2,2).................... 2 Device C (2,3).................... 3 Device D (2,4).
15 .5 UNIT RESET Users can instruct the M-Series DAC with the V93A module, to “reset ” by using the Menu Selection Method to reset the unit. The Unit Reset command does not affect any saved configuration parameters that have been changed from the default values.
16 By responding to the Enter Request : message in the V93A Main Menu with “T” (Logout ), you will take you out of menu mode If you have a modem connection it will terminate that connection. The V93A host module will respond with a message similar to the following: Device A (2,1).
17 Enter Request : .1 STATUS By responding to the menu with a "1" (Status ), you can review the current configuration of the V93A. Below is the default status. Installed Modules :1,2 Port Select Code is................$BT Attention Character is.
18 Exit/Save......1 Set Stop Bits.....4 Set Baud Rate..2 Set Parity........5 Set Word Size..3 Set Xon/Xoff......6 Enter Request : You can now reconfigure the V93A EIA-232 port by sending the appropriate option (1 to 6) from the menu. For example, to change the baud rate to 115.
19 If you type "Y", the new configuration for the selected port is stored permanently in non-volatile memory until. If you type “N” t he V93A will return to the main configuration menu .
20 Enter Port Device Name (Max. 16 characters): or ENTER for no change ...........: If the Port Device Name is satisfactory, type <ENTER>. The V93A will return to the main configuration menu.
21 Type "Y" to change the Attention Character. The V93A will respond with: Enter Attention Character : Type the desired Attention Character. For example, if you type "%", the V93A will respond with Attention Character is...........
22 Enter New Password( 1 - 8 char., CR to end): If the Login Password is correct, type "N". The V93A will store the new Login Password into non-volatile memory and return to the main configuration menu. .8 LOCAL MODEM SETUP By responding with “8” (Local Modem Setup ), you can change the Rings to Answer and the Connectivity Time-out.
23 This time-out can be programmed from 5 to 255 minutes, or 0 (=disable). The timer is started when the modem goes off-hook (DCD goes high), and the modem will return to “on hook” after the time-out has expired. The factory default is 0 (disabled).
24 The V93A has five LEDs on the rear panel that indicate the modem status: TD , RD , CD , MR , and CX . These LEDs are described below. LED Description TD Transmit Data: Indicates the modem is transmitting data. RD Receive Data: Indicates the modem is receiving data.
25 pliers from side to side, so as not to bend chip pins. Pull loosened EPROM all the way out. 4. Install the new EPROM into socket U2 . The EPROM is notched; the notch on the EPROM should line up with the notch on the socket. Be careful not to bend any of the pins.
26 8 V93A MECHANICAL LAYOUT SN: PN:M330A048A C15 C16 C19 C5 C6 C8 C9 J2 L1 L2 LED1 LED2 LED3 LED4 LED5 M1 R6 R7 U10 U11 U2 U8 U9 R9 F1 F2 K K > > È È F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F Error! Switch argument not specified.
27 9 INDEX —A— ASCII character , 19 Attention Character , 19 Auto-Answer, 20 —C— Case sensitive , 15 Communications program , 10 Configuration menu , 17 —D— DCD Logon/Logoff, 21 Disconnect.
An important point after buying a device Bay Technical Associates U140E116-02 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bay Technical Associates U140E116-02 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bay Technical Associates U140E116-02 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bay Technical Associates U140E116-02 you will learn all the available features of the product, as well as information on its operation. The information that you get Bay Technical Associates U140E116-02 will certainly help you make a decision on the purchase.
If you already are a holder of Bay Technical Associates U140E116-02, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bay Technical Associates U140E116-02.
However, one of the most important roles played by the user manual is to help in solving problems with Bay Technical Associates U140E116-02. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bay Technical Associates U140E116-02 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
