Instruction/ maintenance manual of the product 211348D Spalding
Go to page of 16
1 01/03 P/N 211348D T oll-Free Customer Service Number for U.S: 1-800-558-5234 Internet Address: http://www .hydra-rib.com IMPORT ANT! Have any questions?...Don’t go back to the store! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection.
2 P/N 211348D 01/03 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONT O P AGE 1 OF THIS OWNERS MANUAL W ARNING F AILURE T O FOLLO W THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPER TY D AMA GE. Owner must ensure that all pla yers kno w and follow these rules for saf e operation of the system.
3 01/03 P/N 211348D 24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. NOTE: Make sure J-bolts (1) are in the illustrated position.
4 P/N 211348D 01/03 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill.
5 01/03 P/N 211348D Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE.
6 P/N 211348D 01/03 8. 9. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPOR T ANT! Do not over tighten. 9 10 11 10 8 8 8 8 12 7 4 4 9 5 4 4 7 7 4 SHORT END 8 8 Note: This bolt rests outside the upright pole.
7 01/03 P/N 211348D 1 1. 16 4 13 9 4 7 4 10 7 4 10 7 4 16 4 7 4 9 16 4 16 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPOR T ANT! Do not over tighten.
8 P/N 211348D 01/03 12. Secure jack brackets (17 & 18) to lower holes in pole as shown. 7 4 17 4 18 19 19 4 4 7 REAR VIEW NOTE: REFER TO INSTRUCTION MANUAL ENCLOSED WITH ELEV A TOR MECHANISM. INST ALL BACKBOARD AND GOAL AFTER INST ALLA TION OF ELEV A TOR MECHANISM.
9 01/03 P/N 211348D 13. 23 22 13 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING After Installation of elevator mechanism, position H-frame assembly to lowest point.
10 P/N 211348D 01/03 RIM ASSEMBL Y & INST ALLA TION WARNING 14. Install carriage bolt (41) through rim (25), washers (4) and (27) as shown. Tighten nut (43) completely. Place nut (42) about half-way up carriage bolt (41) as shown. 25 4 41 27 43 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE.
11 01/03 P/N 211348D 17. 25 39 40 Insert spacer (20) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) is inserted through hole on top of inner bracket (40). Install hex bolt (44), washers (27) and nut (42) through top holes on bracket (39) through spacer (20) as shown.
12 P/N 211348D 01/03 19. 20. 21. Apply logo label (33) to cover plate (31). Install cover plate (18) on rim (25) using self tapping screws (32) as shown. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing.
13 01/03 P/N 211348D IMPOR T ANT! If pole pad is used, position label (37) above the pole pad. Apply height adjustment label (37) to front of pole as shown. 23. 10 feet (3.05 m) REGULATION RIM HEIGHT IS 10 FEET (3.05 m). 37 22. Check leveling at this time.
14 P/N 211348D 01/03 NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. Refer to Step 10 and Step 11. Secure pole pad (36) as shown. 24. 36 NOTE: Pole pad may NOT be included in this model. NOTE: Elevator mechanism may appear differently than shown.
15 01/03 P/N 211348D Item Qty. Part No. Description 1 4 206677 J-Bolt, 1/2”-13 x 24” 2 8 202459 Nut, Hex 1/2”-13 3 1 920578 Mounting Plate 4 34* 203474 Washer, Flat 1/2” x 1” O.
16 P/N 211348D 01/03 220065 Item #41 (1) Item #24 (8) Item #30 (1) Item #32 (2) Item #23 (8) Item #42 (2) HARDW ARE IDENTIFIER Item #44 (1) Item #43 (1) WARRANTY CARD: Please remember to complete your product registration form on-line at: www.hydrarib.
An important point after buying a device Spalding 211348D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Spalding 211348D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Spalding 211348D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Spalding 211348D you will learn all the available features of the product, as well as information on its operation. The information that you get Spalding 211348D will certainly help you make a decision on the purchase.
If you already are a holder of Spalding 211348D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Spalding 211348D.
However, one of the most important roles played by the user manual is to help in solving problems with Spalding 211348D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Spalding 211348D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
