Instruction/ maintenance manual of the product 21112201 Spalding
Go to page of 10
1 11/05 ID# 211122 01 Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632 7921 Internet Address: http://www.huffysports.com REQUIRED TOOLS AND MA TERIALS: OPTIONAL TOOLS AND MA TERIALS: Ground Sleeve Owners Manual for a 4” (10.
2 ID# 21112201 11/05 P AR TS LIST (SEE P ARTS IDENTIFIER) Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
11/05 ID# 21112201 3 SAFETY INSTRUCTIONS Most injuries are caused by misuse and/or not following instructions. Use caution when using this system. • If using a ladder during assembly , use extreme caution. • T wo (2) people are recommended for this operation.
4 ID# 21112201 11/05 1. 2. Ensure ground is level with playing surface, then dig pole hole. CONTACT UTILITIES BEFORE DIGGING. W ARNING! BOTTOM TOP POLE(S) NOT INCLUDED. FOLLOW MANUF ACTURERS INSTRUCTIONS ACCORDINGL Y . POLE STYLE WILL V ARY NOTE: 24" (61 cm) 24" (61 cm) 6" (15.
11/05 ID# 21112201 5 4. Fill hole approximately 1/3 full with mixed concrete. 3. Insert bottom pole section into ground sleeve (1). Assemble clamps (4) around bottom pole and ground sleeve (1) as shown. 1 2 5 4 1 4 3 IMPORT ANT! Clamp assembly MUST be positioned as shown below.
6 ID# 21112201 11/05 Insert ground sleeve assembly and center in hole ( FIG . A ). Note : Leave 1" below flange exposed for drainage hill. 1" (2.54 cm) SIDE VIEW 6. IMPORT ANT!: CONTINUE ON T O NEXT STEP . DO NOT W AIT FOR CONCRETE TO CURE. PLAYING SURFACE PLA YIN G SURF ACE FIG .
11/05 ID# 21112201 7 Fill hole completely with concrete. 7. 1" (2.54 cm) 1" (2.54 cm) FILL TO HERE 8. T amp down concrete to release air pockets and build drainage hill. Level pole section in all directions several times while concrete is curing.
8 ID# 21112201 11/05 Af ter concrete has cured, remove clamp assembly and lif t bottom pole section from ground sleeve as shown. 9..
11/05 ID# 21112201 9 C O N C R E T E Bounce pole sections together until they no longer move toward taped reference mark. Insert pole cap onto bottom pole end. Mix concrete and fill pole. NOTE: Concrete must cure before going on to the next step. POLE(S) NOT INCLUDED.
10 ID# 21112201 11/05 Lower clamp cover (6) over clamps and snap into proper position. Secure clamps (4) around pole section as shown. Refer to Step 4. Tighten completely. 6 6 Remove pole cap from bottom pole section and insert clamp cover (6) onto bottom section.
An important point after buying a device Spalding 21112201 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Spalding 21112201 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Spalding 21112201 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Spalding 21112201 you will learn all the available features of the product, as well as information on its operation. The information that you get Spalding 21112201 will certainly help you make a decision on the purchase.
If you already are a holder of Spalding 21112201, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Spalding 21112201.
However, one of the most important roles played by the user manual is to help in solving problems with Spalding 21112201. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Spalding 21112201 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
