Instruction/ maintenance manual of the product SNL574GH Smeg
Go to page of 17
Contents 21 1 INSTRUCTIONS FOR SAFE A ND PROPER USE ____________________ 22 2 POSITIONING OF THE HOB ____________________________________ 24 3 ELECTRICAL CONNECT ION __________________________________.
Introduction 22 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE AP PLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WH OLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB.
Introduction 23 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE HOB.
Instructions for the installer 24 2 POSITIONING OF THE HOB The following operation requ ires bui lding and/or carpentr y work so must be carried out by a competent tradesman. Installation can be carrie d out on various m aterials such as masonry , metal, solid wood or plastic laminated woo d as long as they are heat resistant (T 90°C).
Instructions for the installer 25 In case of installation on a hollow compartment with doors, a separating panel has to be p laced under the hob. Keep a minimum distance of 10 mm between the bottom of the unit a nd the panel surface. The panel has to b e easily removable to allow access in th e event of technical service.
Instructions for the installer 26 3 ELECTRICAL CONNECTION Make sure that the voltage and cap a city of the power line conform to the data shown on the plate located under the casing.
Instructions for the installer 27 4 GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the pr ovisions defined by standard regulations in force. To facilitate connection, fitting A on the rear of the a ppliance may be adjusted laterally.
Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make th e connection to the tank according to the provisio ns of st andards r egulations in force. Make sure that feed pressure c onforms to the levels sh own in the table in paragraph “5.
Instructions for the installer 29 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any clea ning or maintenance work, disconnect the appliance from the electrical socket.
Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and p ush support B all the way. Use a d ouble head wrench to remove nozzle C and assemble the suitable one, following the instructions indicated in the refere nce charts, with respect to the type of gas to use.
Instructions for the installer 31 5.3 Regulation for natural gas The hob has been i nspected for G25 (2L3B/P) at a pressure o f 25 mbar. To allow the unit t o work with this type of g as, perform the same operations described in pa ragraph “5.
Instructions for the installer 32 6 FINAL OPERATIONS Having carried out the ab ove adjustments, reassemble the ap pliance following, backwards, the instructi ons in paragra ph “5.1 Removing the hob”. 6.1 Regulation of minimum for natural gas Replace the compo nents on the burner and slide the knobs on the gas tap pins.
Instructions for the installer 33 6.3 Arrangement of burners on hob Burners 1. Auxiliary 2. Semirapid 3. Rapid 4. Rapid large 6. Ultra rapid 7. Double crown 8. Fish pan 10. Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become h ard to turn or lock.
Instructions for the user 34 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted cor rectly. In the ultrarapid burner, notch A must be aligned wit h pin B . Grid C provided is intended for use with wok s (Chinese pans).
Instructions for the user 35 7.2 Practical advice for using the burners For better burner performance and mi nimum gas consumption, flat bottome d, even pans must be used, with covers and proportional in size to the burners (see paragraph “7.3 Diameter of the pans”).
Instructions for the user 36 8 CLEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the applia nce. 8.1 Cleaning Clean the cooking top regularl y every time you use it, obviously after it has cooled.
Instructions for the user 37 8.2 Cleaning of cooking hob components CAUTION: do not wash these components in a dishw asher. In normal use of the hob, the st ainless st eel burner caps and pan- stands tend to be burnished by the high temperature. Clean these parts using very fine abrasive sponges or similar commercial prod ucts.
An important point after buying a device Smeg SNL574GH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smeg SNL574GH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smeg SNL574GH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smeg SNL574GH you will learn all the available features of the product, as well as information on its operation. The information that you get Smeg SNL574GH will certainly help you make a decision on the purchase.
If you already are a holder of Smeg SNL574GH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smeg SNL574GH.
However, one of the most important roles played by the user manual is to help in solving problems with Smeg SNL574GH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smeg SNL574GH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
