Instruction/ maintenance manual of the product CIR34AX3 Smeg
Go to page of 24
Contents 3 1 INSTRUCTIONS FOR SAFE AND PROPER USE _____________________ 4 2 POSITIONING OF THE HOB _____________________________________ 6 3 GAS CONNE CTION ___________________________________________.
Introduction 4 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WH OLE WORKING LIFE OF THE COOKING HOB. WE ADVISE R EADING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEF ORE USING THE COOKING HOB.
Introduction 5 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING.
Instructions for the installer 6 2 POSITIONING OF THE HOB It is the law that all gas a ppliances are installed by authorised persons . Clearance aro und the appliance must comply with the requirem ents of AS5601. The following operati on requires build ing and/or carpentry work so m ust be carried out by a competent tradesman.
Instructions for the installer 7 Bracket ‘ A ’ in the 1st slot Bracket ‘ A ’ in the 2nd slot Bracket ‘ B ’ Short sides Long sides 2.2 Fixing 90 cm hobs on 60 cm base unit If a 90 cm hob is.
Instructions for the installer 8 Overall dimensions: location of gas and electrical connection points (all measures in mm). 60 cm 90 cm hob hob A 35 105 B 65 50 C 30 50 D 85 75 2.
Instructions for the installer 9 REQUIREMENTS 1 Overhead clearances – (Measurement A ) Range hoods and exha ust fans shall be installed in accordance with the manufacturer’s instructions.
Instructions for the installer 10 3 For definition of hob, see Claus e 1.4.64. 4 For definition of triv et, see Clause 1.4.109. 5 Consideration is to be given to windo w treatments when located near cooking appli ances.
Instructions for the installer 11 3 GAS CONNECTION This appliance is suitable for installation with Natur al Gas or ULPG (propane). Refer to page 12 for the relevant burner pressure an d appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator su pplied must be fitted to the gas inlet.
Instructions for the installer 12 4 ELECTRICAL CONNECTION Make sure that the voltage and cap acity of the power line conform to the data shown on the plate l ocated under the casing.
Instructions for the installer 13 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been adjusted for natural gas at a pressure of 1.0 kPa. For functioning with other types of gas the nozzles must be replaced and the primary air adjusted.
Instructions for the installer 14 5.2 Removing the hob (models wi th built-in control panel) 1. Remove the knobs, the gri ddles, the burner caps, the flam e caps and the two rear plugs; 2. Remove the screws “A” which fix the burner supports; 3. Raise the hob, sliding it off the ignition plugs and/or the thermocouples and the gas tap rods; 5.
Instructions for the installer 15 5.4 Adjustment for natural gas The hob has been adjusted for natural gas at a pressure of 1.0kPa. To allow the unit to work back with this type of gas, after it has been adjusted for ULPG, perform the same operations described in paragraph “5.
Instructions for the installer 16 6 FINAL OPERATIONS Having carried out the above adjustments, reassemble the ap pliance following, backwards, the instructions i n paragraph “ 5.1 Removing the control panel / 5.2 Removing the ho b”. 6.1 Adjustment of minimum for natural gas Light the burner and take it to the minimum .
Instructions for the installer 17 6.2 Arrangement of burners on the hob (hobs with separable control panel). 60 cm hobs BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid large 5. Wok 90 cm hobs BURNERS 1. Auxiliary 2. Semirapid 3. Rapid 4. Fish burner 5.
Instructions for the installer 18 6.3 Arrangement of burners on the hob (hobs with b uilt- in control panel). 60 cm hobs BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid 5. Wok 6.4 Lubrication of gas taps With time it may happen that the gas taps get blocked and h ard to turn.
Instructions for the user 19 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted cor rectly. In the wok burner, notch A must be aligned with pin B . Grid C provided is intended for use with wok s (Chinese pans).
Instructions for the user 20 7.3 Diameter of containers Burners Ø min. and max . (en cm.) Auxiliary 12-14 Semirapid 16-20 Rapid 22-26 Rapid large 22-26 Wok 22-34 Fish burner Special oval-shaped vessels 7.4 Electric elements 7.4.1 Turning on electric elements Hobs may be fitted with an electric element of various diameter.
Instructions for the user 21 WARNING When switching on the electric element for the first time, or if the electric element has not been used for a long time, to remove any humi dity from the insulating material it should be dr ied out by placing the electric ele ment on position 1 for 30 minutes.
Instructions for the user 22 8 CLEANING AND MAINTENANCE Before any intervention, disc onnect the power supply of the device. 8.1 Cleaning Clean the cooking top regul arly every time you use it, obviously after it has cooled.
Instructions for the user 23 8.2.2 The electric element After use, to make sure that the surf aces are clean and lon g lasting, the electric element must be treated w ith specific cleaning pro ducts which are available on the market. This necessary operation pr events oxidisation (rust formation).
Instructions for the user 24 9 PROBLEMS AND CAUSES Each of the following cases is caused by an abnormal operation of the appliance and shoul d be dealt with by a authorised pers ons: please contact your local dealer or Service Center in case yo u detect any of these malfunctioning.
.
914773237/ B.
An important point after buying a device Smeg CIR34AX3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smeg CIR34AX3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smeg CIR34AX3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smeg CIR34AX3 you will learn all the available features of the product, as well as information on its operation. The information that you get Smeg CIR34AX3 will certainly help you make a decision on the purchase.
If you already are a holder of Smeg CIR34AX3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smeg CIR34AX3.
However, one of the most important roles played by the user manual is to help in solving problems with Smeg CIR34AX3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smeg CIR34AX3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
