Instruction/ maintenance manual of the product 3000i Smart Technologies
Go to page of 18
99-00360-02 Rev A0 Room Control Module Installation Guide for the Interactive Whiteboard.
FCC Warning This equipment has been tested and found to comp ly wi th the limits for a Class A digita l device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operat ed in a commercial env ironment.
99-00360-02 REV A0 Contents Contents Installing the Room Control Module ................................................ 1 About the Custom Straight-Through MOD4 I 2 C Cabl es................................. 1 Removing the Bl ank P anel .............
.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 1 Installing the Room Control Module These instructions explain how to install the SM ART Room Control Module (part No.
2 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 Removing the Blank Panel NOTE : We recommend that you wear the suppli ed anti-static wrist strap throughout the installation process. This wrist strap protects electronic components from damage due to electrostatic discharge.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 3 Completing the Computer 2 (X-Port 20) Serial Panel Connections 1 Disconnect the computer 2 serial cabl e from the computer 2 serial panel. Comput er 2 Seri al Cable R e a r o f C a b i n e t 2 Remove the four screws used to attach the computer 2 serial panel.
4 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 4 Disconnect the MOD4 I 2 C cable at the top of the computer 2 serial panel. MOD4 I C Cable R e a r o f C a b i n e t 2 5 Run this cable behind the patch panel and through the opening where the blank panel was removed.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 5 7 Tilt the computer 2 serial panel and pull it outsi de the cabinet. As you pull the panel out, flip it so the RJ11-6 (RJ12) connectors remain insi de the cabinet. The front of the panel should face you.
6 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 2 Bundle any excess cable, fasten it with the supplied tie wrap, and clip off any excess tie-wrap length. Room C o ntrol Module Tie Wrap R e a r o f C a b i n e t T h i s d e v i c e c o m p l i e s w i t h p a r t 1 5 o f t h e F C C r u l e s .
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 7 Updating the Control Panel Firmware The procedure for updating the control panel firmwa re varies depending on the last four digits of the serial number on your 3000i.
8 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 2 Reach inside the cabinet, behind the front panel. Lift the serial-controller metal housing up and then back to release it from the keyholes on the panel. 3 Carefully lower the serial controller through the opening in the front panel.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 9 6 Reach inside the cabinet and attach the serial controller metal housing to the inside of the front panel. To do this, fit the two partially inserted screws on the metal housing into the keyholes on the front panel.
10 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 3 Carefully lower the serial controller through the opening in the front panel. The cables should remain connected to the serial controller. You’ll notice that the I 2 C control panel flash cable is bundled with the DB9 serial cable.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 11 2 Connect the DB9F end of a DB9F/custom cable to the Control port on the Room Control Module. This cable isn’t supplied by SMART Te chnologies. It’s usually supplied by the third- party room control vendor.
12 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 2 Open the WBDiag application as follows: a On the Boards tab, click the Log button. The Status Log opens. b Click the Diagnostics button. The WBDiag application opens. 3 Open the port in WBDiag as follows: a There are four numbered COM port buttons on the WBDiag toolbar.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 13 3 Browse to the hex file and open it. The download process takes approximately 20 to 30 minutes. We recommend that you not disturb th is process by performing any work on the laptop or internal computer for the duration of the download.
14 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 Customer Support SMART’s Technical Support team welcomes your call. However, you may want to contact your local reseller first if you experience problems with any SMART product.
An important point after buying a device Smart Technologies 3000i (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Smart Technologies 3000i yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Smart Technologies 3000i - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Smart Technologies 3000i you will learn all the available features of the product, as well as information on its operation. The information that you get Smart Technologies 3000i will certainly help you make a decision on the purchase.
If you already are a holder of Smart Technologies 3000i, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Smart Technologies 3000i.
However, one of the most important roles played by the user manual is to help in solving problems with Smart Technologies 3000i. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Smart Technologies 3000i along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
