Instruction/ maintenance manual of the product a1001 Axis Communications
Go to page of 20
INSTALLATION GUIDE AXIS A1001 Network Door Controller.
Liability Every care has b een taken in the preparation of this document. Plea se inform your lo cal Axis offic e of any inaccuracies or omissions. Axis Commu nications AB cannot be held responsible for any technical or typo graphical errors and reserves the right to make changes to the product and manuals without prior notice.
Safety This product complies with IEC/EN/UL 60950-1, Safety of Information Technology Equipme nt. The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) to IEC/EN/UL 60950-1.
hardware conf iguration pages. Use the generated hard ware pin chart. Make sure the pr oduct is disconnected from power (PoE/DC) while connec ti ng devices to the product. • For information about how to connect other wires, such as power wires to locks, readers and oth er devices, see the manufacturers’ i nstructions.
AXIS A1001 Install ation Guide Page 5 1x 1x 4x 2x 1x 1x 5x 5x Owner Authentication Key The authentication key on this label is used to authenticate the owner/administrat or of the product’s unique serial num ber (S/N), as shown at the top of the label.
Page 6 AXIS A1001 Installation Guide 1.
AXIS A1001 Install ation Guide Page 7 2.
Page 8 AXIS A1001 Installation Guide 3 STP STP P ower over Ethernet IEEE 802.3af/80 2.3at T ype 1 Class 3.
AXIS A1001 Install ation Guide Page 9 4 192.168.0.90 AXIS IP Utility www.axis.com/techsup.
Page 10 AXIS A1001 Installation Guide 5 6.
AXIS A1001 Inst allation Guide Page 11 7.
Page 12 AXIS A1001 Installation Guide 8.
AXIS A1001 Inst allation Guide Page 13 9 STP.
Page 14 AXIS A1001 Installation Guide 10.
AXIS A1001 Inst allation Guide Page 15 P ower connector DC input: 1 0–30VDC, max 26W Max load on outputs: 14 W AWG 28–16 (CSA) AWG 30–14 (CUL/UL) Door connectors Digital input: 0 to max 40VDC Reader data connectors Max cable length: 30 m (98.
Page 16 AXIS A1001 Installation Guide STP STP P ower over Ethernet IEEE 802.3af/80 2.3at T ype 1 Class 3 11.
AXIS A1001 Inst allation Guide Page 17 12.
Page 18 AXIS A1001 Installation Guide 13 www.axis.com/warranty T1 0.
.
Installation Guide Ver.1.1 AXIS A1001 Network Door Controller Printed: November 2013 © Axis Communicat ions AB, 20 13 Part No. 54595.
An important point after buying a device Axis Communications a1001 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Axis Communications a1001 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Axis Communications a1001 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Axis Communications a1001 you will learn all the available features of the product, as well as information on its operation. The information that you get Axis Communications a1001 will certainly help you make a decision on the purchase.
If you already are a holder of Axis Communications a1001, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Axis Communications a1001.
However, one of the most important roles played by the user manual is to help in solving problems with Axis Communications a1001. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Axis Communications a1001 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
