Instruction/ maintenance manual of the product VCB-9124 Sanyo
Go to page of 19
INSTRUCTION MANUAL VCB-9124 B/W CCD CAMERA About this manual B efo re in st a ll in g a nd us in g th e ca m e ra, pl ea se re ad th is ma nu al carefully.
SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty .
Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform to all local codes.
CONTENTS PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PARTS NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PREPARATIONS AND CONNECTIONS . . . . . . . . . . . . . . .
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit.
PARTS NAMES AND FUNCTIONS MONITOR GND 1 0 BLC L E V E L 5 4 3 2 2 F G 9 7 A H IL JK 6 L-PHASE 8 C B A 1 1 1 1 Manual pan, tilt and rotation The angle of the lens can be adjusted manually in ranges indicated below.
PARTS NAMES AND FUNCTIONS 1 Camera unit fixing screws (4) These screws are used to attach the camera unit to the base. Tighten the four screws evenly when attaching the camera unit. 2 Screw openings for base installation These openings are to attach the base to the ceiling or a wall using the four supplied tapping screws.
PARTS NAMES AND FUNCTIONS 8 Secondary lens cover 9 Lens F F ocus ring To set the focus, loosen the focus ring knob, then turn the ring towards ∞ (infinity) or N (near) as necessary.
PREPARATIONS AND CONNECTIONS Concerning the coaxial cable To connect the camera to peripheral devices, use a coaxial cable with BNC plug. • Cable type RG-6U (5C-2V), 500 m maximum.
CONNECTIONS AND INSTALLATION Basic connections for monitoring or recording The peripheral devices (VCR, monitor, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Plug the AC adaptor to a wall outlet.
CONNECTIONS AND INSTALLATION Coaxial cable connection 1 Cut and prepare the extremity of the coaxial cable (sold separately), as illustrated. 2 Attach the coaxial cable to the base.
CONNECTIONS AND INSTALLATION 2 Install the camera unit onto the base. Connect the video signal cable plug ( B ) and the power supply cable plug ( C ) from the base to their respective connectors on the camera unit. Then install the camera unit onto the base.
SETTINGS AND ADJUSTMENTS The digital process may disturb the image for about 5 seconds after the camera is turned on. Factory settings The camera is shipped from the factory with the following settings. These settings should give adequate results under normal conditions.
SETTINGS AND ADJUSTMENTS Line phase adjustment When using a camera switcher to connect two cameras or more to one monitor, there may be a vertical roll of the images when switched, if the phases differ. In such a case, adjust as described below. Using the camera switcher, switch the display on the monitor from camera 1 to camera 2.
SETTINGS AND ADJUSTMENTS Zoom and focus adjustments After the camera has been installed, the zoom and focus must be adjusted while viewing on a monitor the transmitted image. 1 Remove the lens cover, then press on both sides of the secondary lens cover to remove it.
INFRARED (IR LED) ILLUMINATION RANGE Conditions Room lighting: 0 lux Reflection rate: 89.9% on subject Internal lens: at f=2.6mm 3m 2m 4m 1m 1m 2m 3m 4.
TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correc tly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Center.
SPECIFICATIONS TV system Based on the EIA system Scanning system 525 TV lines, 60 field/sec., 2:1 interlace Image device Interline transfer method, 1/3 inch solid state CCD Picture elements 537 (H) × 505 (V) Effective picture elements 510 (H) × 492 (V) Synchronization system Internal sync.
SPECIFICATION DIMENSIONS 112mm 11mm 83.5mm 66.7mm 110mm φ 83.5mm φ 4.3mm φ 6- L73D 4/US GB 1998, 3, 12 English 17.
An important point after buying a device Sanyo VCB-9124 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo VCB-9124 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo VCB-9124 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo VCB-9124 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo VCB-9124 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo VCB-9124, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo VCB-9124.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo VCB-9124. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo VCB-9124 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
