Instruction/ maintenance manual of the product 1S84 Rubbermaid
Go to page of 16
RUBBERMAID 7' x 10' 6" RESIN STORAGE BUILDING ASSEMBL Y INSTRUCTIONS Pre-Assembly: • Review the parts list and make sure that no parts are missing. • Review ALL assembly steps before beginning instructions. • Level the area where the shed will be located.
Level construction site before beginning assembly of shed. A foundation may be constructed if desired. 1 FLOOR PLAN: Size the construction site to fit the entire floor . Allow clearance for opening front and back doors. OPTIONAL STEP: If desired, recessed anchor locations (8 places) can be used to anchor the shed floor to a foundation after Step 6.
3 Place the Floor Panel (J-5H51) on the foundation. Connect two Repeat Floor Panels (K-5H52), install Screws (AA) 14 places. Optional Step: If desired, recessed anchor locations (8 places) can be used to secure the Floor to the Foundation, see Step 1.
5 Using a screwdrive r , punch out the screw holes on the top of Left Side Panel (C) 2 places . Connect Left Side Panel (C) into Front Floor (J-5H51). C C Screw Holes click 6 Lubricate dovetails on Left Front Panel (H) 4 places with liquid soap.
9 Using a screwdriver , punch out the screw holes on the top of the Left Side Panel (C) 2 places. Align lap joint between Left Side Panels. Connect Left Side Panel (C) into Repeat Floor (K-5H52). C C C C click 10 Install Wall Connectors (Q) 5 places. 2 1 C C 1 2 C Q C 11 Lubricate dovetails on Left Back Panel (E) 4 places with liquid soap.
13 14 15 16 Lubricate dovetails on Right Back Panel (G) 4 places with liquid soap. Connect Right Back Panel (G) into dovetails of Right Side Panel (D), engage snaps on bottom of Right Back Panel (G) into Repeat Floor (K-5H52). E G D 1 2 1 2 NOTE: Front Gable and Doors not shown.
17 18 19 20 Set the Left Door Panel (AK) face down on the ground. Slide the Hinge Reinforcement (PP) into the hole on the top door pin. The Hinge Reinforcement (PP) will slide in until it is below the end of the door pin.
21 22 23 24 Install Left Door Panel (K) inserting the lower hinge pin into Front Floor (J-5H51) socket, lift the left end of the Gable (M) enough to insert the top hinge pin on Left Door Panel (K) into the Gable (M) socket.
25 26 27 28 Apply Ridge T ape (HH) to Ridge Cap (GG) 2 places. Snap Ridge Cap (GG) onto the Ridge Beam Assembly covering the seam. GG HH HH GG RS RL GG RS RL Place the Ridge Beam Assembly into cups at the top of each Gable (M).
29 30 Align slots in Ridge Beam Assembly with holes in Gable (M) tab, install Bolt (BB), Washer (CC), and Nut (DD) 1 place, ONL Y TIGHTEN NUT “FINGER” TIGHT . Bolt Head Washer Nut Plastic T ab on Gable DD CC BB M M R Using a screwdrive r , punch out the screwholes on the Left Skylight Roof Panel (AN ) 6 places.
Lubricate roof snaps on left side of the front Gable (M) 4 places. Raise the Left Roof Panel (N) onto the left side of the shed assembly , the arrows on the Roof Panel should face the inside of the shed and point towards the Ridge Beam Assembly .
Raise the Left Skylight Roof Panel (AN) onto the left side of the shed assembly , the arrows on the Roof Panel should face the inside of the shed and point towards the Ridge Beam Assembly. Using (2) stepstools (1 inside shed, 1 outside shed), lift the bottom of Left Skylight Roof Panel (AN) above horizontal and guide into the Ridge Beam Assembly .
Install Roof Connectors (T) 8 places. Y ou may need to lift the roof panels to avoid the 2"x6" lumber . 35 T 1 2 2 1 Engage all snaps between the Roof Panels and Gables.
Repeat Steps 29-35 for Right Roof of shed. 37 Install Screws (AA) 16 places in front and back Gable (M). 38 Back of shed shown Caution: When installing screws do not overtighten.
88.09" 128.85" 94.63".
Customer Service T oll Free: 1-888-895-2110 M–F 8:30 AM to 5:00 PM EST or visit us at www .rubbermaid.com 1869756 W e hope you enjoy your Rubbermaid ® 7' x 10' 6" Storage Building! For more information on all Rubbermaid ® products, go to www .
An important point after buying a device Rubbermaid 1S84 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rubbermaid 1S84 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rubbermaid 1S84 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rubbermaid 1S84 you will learn all the available features of the product, as well as information on its operation. The information that you get Rubbermaid 1S84 will certainly help you make a decision on the purchase.
If you already are a holder of Rubbermaid 1S84, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rubbermaid 1S84.
However, one of the most important roles played by the user manual is to help in solving problems with Rubbermaid 1S84. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rubbermaid 1S84 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
