Instruction/ maintenance manual of the product CL72-A Arrow Plastic
Go to page of 24
* Size rounded off to the nearest foot BUILDING DIMENSIONS CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION.
2 Owner's Manual Bef ore beginning constr uction, chec k local building codes regarding f ootings, location and other requirements. Study and understand this owner's manual. Impor tant infor mation and helpful tips will make y our construction easier and more enjo y able .
3 Selecting and Pr eparing Y our Site: Before assemb ly , y ou will want to decide on a location f or your b uilding. The best location is a le vel area with good dr ainage. •Allow enough working space for ease of moving parts into position during assembly.
4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build- ing.
Finish: F or long lasting finish, per iodically clean and wax the e xter ior surface. T ouch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manuf acturer's recommendation.
6 ACCESSORIES.... A6 WEB * Some drilling required to fit buildings without mid-wall bracing. Model No. SS404 • Makes 8" to 12" (20-30cm) wide shelves in any length. • Brackets, braces, hardware included. Lumber is not included. Model No.
THIS P AGE WA S LEFT BLANK INTENTIONALL Y 7.
THIS P AGE WA S LEFT BLANK INTENTIONALL Y 8.
The Foundation For Y our Building 9 FRONT (DOOR) FRONT (DOOR) Foundation BJ09 Note: Finished Slab dimensions, with lumber removed. OPTION 1: W ood Platform If you decide to build your own foundation, be sure to select the appropriate materials.
It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring Down The Building Anchoring A10 Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete foundation.
11 66150 Screw Driver Holder (1) 66149 Tool Hook (5) 66462 Hasp (1) 66684 Spring Latch (1) 66183 Roof Trim Cap (4) 66463 Swivel Staple (1) 66714 #6-32x7/16" Flat Hd Bolt (16) 66646 Washer (164) (.
Parts List BK12 12 Assembly P a r t P a r t Quantity Check K e y No . Number Description i n C a r to n List 1 8984 Side Floor F rame 2 2 9429 Ramp 1 3 9430 F ront/Rear Floor F rame 2 4 9431 Mid W all.
13 Assembly by Key No. BK13.
S tep 1 BJ14 14 The door header reinforces the front wall and roof. It is made up of two pieces. 1 Positioning the door header as shown, attach a starter strip to head- er using four screws, where shown.
S tep 2 BK15 15 STEP 7 ● P ar ts Needed F or ● Door Assembly ● ● ● ● ● 9435 Horizontal Door Brace (four) ● ● ● ● ● 9936 Right Door (one) ● ● ● ● ● 9937 Left Door (one.
16 S tep 3 BJ16 The floor frame at the front of building is made up of two pieces. Proceed as follows: 1 Center the ramp on top of the front floor frame. Join the frames by in- serting four screws. 2 Place the floor frames on the foun- dation. Assemble the four corners of the floor frame using two screws at each corner as shown.
17 S tep 4 BK17 NOTE The remainder of the building assembly requires many hours. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. Each screw and bolt in the wall re- quires a washer.
S tep 5 BJ18 18 The main frame pieces give rigidity to the front and rear walls. 1 Fasten the rear wall angle across the top of the rear wall using four screws.
S tep 6 BK19 19 Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it. The rear header supports the rear wall and roof. 1 Fasten the wall panels at the top and bottom with screws. 2 Fasten overlapping ribs using two screws and a bolt with nut.
20 S tep 7 BJ20 1 Lift and fasten a right and left gable, under rear header, to the right and left hand wall with four screws. Join gables to header in the rear corners, using a screw. 2 Position roof rafters across width of building, under rear header, with tab on top of door header.
S tep 8 BK21 21 STEP 1 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. 1 Fasten a door jamb to the front corner panel with one bolt and nut as shown. 2 Fasten the top of the door jamb to the door header with two screws.
S tep 9 BJ22 22 STEP 1 Each screw and bolt in the roof re- quire a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the roof panel fit better, and holes will align. 1 Position roof panel on top and fas- ten to rear header, roof rafters and gables using screws.
23 S tep 10 BK23 Screw Driver Holder (1) 1 Fasten the mid wall frame across the middle of the rear wall using eight bolts and nuts. 2 Position a shelf inside mid wall frame and slide to the end of building. Fasten using bolts and nuts through panels. Repeat Step 2 for the opposite shelf.
S tep 1 1 BK24 24 ● ● ● ● ● Right Door Assembly (one) ● ● ● ● ● Left Door Assembly (one) ● P ar ts Needed F or ● Door Installation CL72-A BK24 1 Position doors in corners of door opening as shown and fasten hinges with 7/16" flat head bolts and #6-32 hex nuts.
An important point after buying a device Arrow Plastic CL72-A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Arrow Plastic CL72-A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Arrow Plastic CL72-A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Arrow Plastic CL72-A you will learn all the available features of the product, as well as information on its operation. The information that you get Arrow Plastic CL72-A will certainly help you make a decision on the purchase.
If you already are a holder of Arrow Plastic CL72-A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Arrow Plastic CL72-A.
However, one of the most important roles played by the user manual is to help in solving problems with Arrow Plastic CL72-A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Arrow Plastic CL72-A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
