Instruction/ maintenance manual of the product REXT650-1 REVO
Go to page of 20
1 / 3 ' ' D O U B L E S C A N C C D H I G H R E S O L U T I O N W D R S u p e r H i g h R e s o l u t i o n D a y & N i g h t C o l o r C a m e r a.
.
- ii - W A R NI NG S : C A UT I O N : CAUTION CAUTION CAUTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE P AR TS INSIDE.
- iii - FC C IN FOR MA T ION : THI S EQUI PMEN T H AS BEEN TESTE D AND FOU ND TO COMPL Y W ITH THE LIMIT S FOR A C LAS S A D IGIT AL DEV ICE, PURS UANT TO P AR T 1 5 OF THE FCC RUL ES.
- iv - I M P O R T A N T SA F E G U A R D S 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
INTRODUCTION 1 CAMERA CONNECTIONS 2 W ALL BRACKET MOUNTING 2 CAMERA OVERVIEW 3 CONTROL AND CONNECTIONS/DA Y&NIGHT I/O/ ALARM OUT TERMINALS 9 WIRING DIAGRAM 10 HOUSING KIT SPECIFICA TIONS 10 CAMERA.
- 1 - The camera provided high-quality image using SONY Wide Dynamic 1/3” Super-HADII PS 960H CCD and digital signal processing LSIs. Features: 1/3" Super-HADII PS 960H CCD Super high-resolution of 650TV lines Wide Dynamic Range (~x512) Excessive High-Light Compensation Back Light Masking (MAX.
- 2 - C A M E R A C O N N E C T I O N S 2 1 REMINDER: Never aim the camera directly into the sun. 1. Color Lead Wire & Color Display Label 2. Video : BNC connector used to connect the camera to a monitor, switcher , etc.
- 3 - C A M E R A O V E R VI E W REAR VIEW 2 3 4 6 1 5 1 0 7 8 9 Left Button Up Button Enter Button Right Button Down Button Day/Night External I/O Motion ALARM OUT RS - 485 UTP(optional) Power Indica.
- 4 - 3) EHLC(Excessive High Light Compensation) : EHLC mode on. excessive lighting compensation is performed when the weighting on the high-brightness side is increased. 4) Auto(Auto Weighting BLC) : Auto weighting BLC on. 5) Spot(User Setting BLC area) : Spot metering mode on.
- 5 - 5) Mine : Mine area mode. By this function, User can draw motion detection area with free dotting Set Mine : Press the Enter button to Set Mine mode. < > : Move : Mine Zone move using the Left and Right buttons. UP:Set : Mine Zone setting using the Up button.
- 6 - The distance is too long Several Object Crossing Object Camera Installed at the ceiling Crossing object is none One object is passing. <Picture/DNR> 1) Sharpness : Adjust sharpness of outl.
- 7 - In low luminance environment, the accuracy is down of the result. In very low luminance environment, operation is not be performed. It is not be performed when moving object is exist. <System Setup> 1) Cam Info : Camera basic information display Cam ID/Baud rate/Protocol/Firmware Ver .
System Init Cancel : Back to General Setup Menu. Confirm : Initialize all data. (Factory Default) 3) Lens Iris : DC, Video, Manual Lens selected Iris : adjust AE Speed DC lens and video lens can adjust AE Speed Normal AE Ref (Auto Exposure Reference Level) : Press the Enter button to access the AE Ref.
CONTROL AND CONNECTIONS/DA Y&NIGHT I/O / ALARM OUT TERMINALS 1) UTP Connections/Video output (optional) 1 PIN: UTP- 2 PIN: UTP+ 2) DA Y&NIGHT I/O T erminals T o select Day/Night mode using external equipment, connect control lines to the appropriate terminals.
- 10 - WIRING DIAGRAM 24V ac Out to Heater 24V ac Power Supply Output 24Vdc Out to Blower 24V ac Power Supply Input Ground Ground (B+) (Ground) J3 J6 J4 J5 J1 24 V ac * HEA TER AND BLOWER H O U S I N G K I T SP E C I F I C A TI ON S 5.5(14) 2.5(6.4) 2.
- 1 1 - CAMERA SPECIFICA TIONS Power source Power consumption Image sensor Effective pixels Scanning system Scanning frequency Sync. system Resolution Min. illumination 2:1 interlace 15.734KHz(H) x 59.94Hz(V) Internal / Line lock 5 0 d B ( A G C O F F ) 0.
MEMO.
.
50 3 02 78 4A WD R Sup er Hig h Res olu tio n Da y and Nigh t Co lor Cam era PR I NT ED IN KOR E A.
An important point after buying a device REVO REXT650-1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought REVO REXT650-1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data REVO REXT650-1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, REVO REXT650-1 you will learn all the available features of the product, as well as information on its operation. The information that you get REVO REXT650-1 will certainly help you make a decision on the purchase.
If you already are a holder of REVO REXT650-1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime REVO REXT650-1.
However, one of the most important roles played by the user manual is to help in solving problems with REVO REXT650-1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device REVO REXT650-1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
