Instruction/ maintenance manual of the product 1190 Regalo
Go to page of 10
Maxi Gate MODEL NO: 1190 Owner’s Manual READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. Regalo International, LLC. 3200 Corporate Center Drive, Suite 100 Burnsville, MN 55306-9803, USA Toll Free: 866-272-5274 Made in China .
The four wall mounting brackets must be used with this gate. If not used, the gate may dislodge from the opening and become unstable. This gate can be used in openings from 34 inches to 39 inches AND 49 inches to 59 inches. This gate will not work with openings that have a width between 39 inches and 49 inches.
1 Check to mak e sure y ou ha v e all of the par ts shown: A. Maxi Gate Main Panel B. Maxi Gate Extension Panel C. 4 Maxi Mounting Brackets D. 4 Maxi Threaded Rods E. Stabilizing Foot F. 8 - 1” Screws ( requires a Phillips/crosshead screwdriver ) G.
2 Assem blin g and In stalling Y our G ate: Step 1. Determine the width of your doorway or opening. F or openings between 34” and 39”: Remove and discard the pr otective end screws locat ed at points X and Y in Diagram A, then skip to Step 3. F or openings between 49” - 59” : Pr oceed to Step 2.
3 Step 3. Screw in the 4 Threaded Rods into the 4 corners of the assembled gate . The Threaded Rods do not need to be fully screwed in, final adjustmen ts will be made before completing installation.
4 Step 5. Use the 8 included 1” Screws to attach the Maxi Mounting Brackets t o the wall at the locations you marked in Step 4. NO TE: The Mounting Brackets must be orientated so that the Release T abs are tow ards the top .
5 Step 7. Connect the assembled gate to the wall by inserting the flat ends of the Threaded Rods into the semi-circle slot at the bottom of each Maxi Mounting Brackets. A djust the length of the threaded rods appr opriately to allow f or installation.
6 Remo ving the Gate F rom the W all: T o release the gate from the wall , simply press down on the Release T abs on each of the four Maxi Mounting Brackets while lifting the Threaded Rods upwards and out of their locked position.
Replacemen t P ar ts A v ailable In the event of any damage or breakage, the following replacement parts are available for order by contacting Regalo Customer Service. Contact Regalo for questions and replacement parts. For questions about the use of your gate, call our customer care line 866-272-5274.
12/4/2013_BL Regalo International, LLC. 3200 Corporate Center Drive, Suite 100 Burnsville, MN 55306-9803, USA Toll Free: 866-272-5274 Made in China.
An important point after buying a device Regalo 1190 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Regalo 1190 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Regalo 1190 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Regalo 1190 you will learn all the available features of the product, as well as information on its operation. The information that you get Regalo 1190 will certainly help you make a decision on the purchase.
If you already are a holder of Regalo 1190, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Regalo 1190.
However, one of the most important roles played by the user manual is to help in solving problems with Regalo 1190. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Regalo 1190 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
