Instruction/ maintenance manual of the product 580 RCA
Go to page of 104
SpeedT ouch™580 Wireless Multi-User ADSL Gateway Setup and User’ s Guide Release R1.0 (R4.2.7).
.
SpeedT ouch™ 580 Setup and User’ s Guide Release R1.0 (R4.2.7).
Status v3.0 Reference E-DOC-CTC-20040123-0001 Shor t Title Setup and User's Guide ST580(i) R1 .0 (R4.2.7) (en) Copyright © 2004 THOMSON. All r ights reserved. Passing on, and copyi ng of this document, use and communication of its contents is not perm itte d without written authorization from THOMSON.
E-DOC-CTC-20040123-0001 v3.0 3 Contents 1 SpeedTouch™ Installati on ........................ .................... 5 1.1 Getting Acquainted with the SpeedTouch™ ............................. ....................... 6 1.2 Setting Up the SpeedTouch™ .
E-DOC-CTC-20040123-0001 v3.0 4 4.2 Connect to the Internet via a Host PPPoE Dial-in Client ............................. 41 4.2.1 Using an MS Windows XP BroadBand Con nection ................. ................... .............. ............. 42 4.2.2 Using the Mac OS X PPPoE Di al-in Client .
1 SpeedTouch™ Installation E-DOC-CTC-20040123-0001 v3.0 5 1 SpeedT ouch™ Installation Introduction Thank you for pur chasing a SpeedT ouch™ Wireless Multi-User ADSL Gatewa y! With the SpeedT ouch™580 Wir eless Multi-User ADSL Gatewa y two cutting-edge technologies are combined: ADSL and Wir eless LAN (WLAN).
1 SpeedTouch™ Installation E-DOC-CTC-20040123-0001 v3.0 6 1.1 Getting Acquainted with the SpeedT ouch™ Introducing the SpeedT ouch™ P r io r t o p ro c e ed i n g , p le a s e m a ke su r e t o re ad first the SpeedT ouch™ Qu ick Installation Guide.
1 SpeedTouch™ Installation E-DOC-CTC-20040123-0001 v3.0 7 Back panel layout The following connectors are a vailable on th e SpeedT ouc h™580: a four por t 10/ 100Base-T Half-/Full-duplex au to-sensing MDI/MDI-X Ethernet switch, a USB port and a DSL line port .
1 SpeedTouch™ Installation E-DOC-CTC-20040123-0001 v3.0 8 Ethernet port LEDs Each of the y ellow mark ed Ethernet por ts on the rear panel has one LED ( B ) to indicate the connection integrity (activity).
1 SpeedTouch™ Installation E-DOC-CTC-20040123-0001 v3.0 9 1.2 Setting Up the SpeedT ouch™ W all mounting assembly The SpeedT ouch™580 can be mounted on a wall using the two mounting brackets at the bottom or can setup in an upright posi tion using a stand or the standard desktop 'mount'.
1 SpeedTouch™ Installation E-DOC-CTC-20040123-0001 v3.0 10 ADSL ser vice The appr opriate DSL ser vice must be a vailable at your pr emises: • ADSL ser vice must be enabled on your telephone line.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 11 2 SpeedT ouch™ Local Networking Setup Introduction The SpeedT ouch™ offers thr ee local netw orking solutions: • Wir ed Etherne t • Wireless Ethernet • USB (1.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 12 2.1 Ethernet Connection Setup Local network The SpeedT ouch™ Ethernet por ts on the ba ck panel allow y ou to connect the Speed- T ou ch™ to an existing 10 or 100Base-T Ethernet network or one (or more) computer(s) with installed Ethernet car d.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 13 2.2 USB Connection Setup for Microsoft Windows Suppor ted Operating Systems Installing and using th e SpeedT ouch™ USB co nnect.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 14 4 Th e W in dow s Fou nd New Ha rdw are Wi za rd a pp ea rs : This wizard will guide you thr ough the installation procedur e of the USB drivers.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 15 Ve r i f y i n g U S B connectivity The SpeedT ouch™ US B connection is repr esented as a local network interface.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 16 2.3 Wireless Connection Setup Introduction The SpeedT ouch™580 featur es a Wir e less LAN Access P oint (AP) which beha ves as .
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 17 Antennas The SpeedT ouch™580 features tw o antennas: one internal and one ex ternal.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 18 Level 2 This le vel uses Wi-Fi Pr otected Access (WP A) to prov ide state of the art security .
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 19 2.3.1 First-time Wireless Client Association Initial SpeedT ouch™ wireless configuration When the SpeedT ouch™ lea v es the factory and after e ve r y Reset-to-Defaults (See “7.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 20 First-time association example Below an example is pr ovided, showing ho w the SpeedT ouch™ wirel ess network is presented towa.
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 21 2.3.2 Connecting Wireless Clients Before you connect other wireless clients In case the SpeedT ouch™ has not b een configur ed .
2 SpeedTouch™ Local Networking Setup E-DOC-CTC-20040123-0001 v3.0 22 Registering wireless clients In case New stations are allo wed (via registration) is enabled, you can r egister new wir eless net.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 23 3 SpeedT ouch™ Configuration Setup Internet connectivity Some configuration ma y b e r e quir ed to prepare the SpeedT ouch™ for Internet connec- tivity .
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 24 3.1 Microsoft Windows SpeedT ouch™ Configuration Setup Suppor ted MS Win do ws OS s One of the following MS Windows OSs must be installed on your PC(s): • MS Windo ws 98SE • MS Windows ME • MS Windows NT4.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 25 Detection of the SpeedT ouch™ Pro ceed as follows: 1 Insert the SpeedT ouch™ Setup CD-R OM in your PC's CD-R OM driv e. The SpeedT ouch™ CD Browser will start automatically .
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 26 4 The Initial Setup window appears: Click Setup m y SpeedT ouch™ to star t the SpeedT ouch™ Se tup wizard. 5 The W elcome to the SpeedT ouch™ Setup Wizard window appear s: Click Next .
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 27 7 The SpeedT ouch™ Setup Wizard will sear ch for the SpeedT ouch™ on the net- work. The following window sho ws the detection progr ess: 8 The SpeedT ouch™ Setup Wizard should fi nd y our SpeedT ouch™ device on the local netw ork.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 28 Configuration of the SpeedT ouch™ (and PC) Pro ceed as follows: 1 As soon as the Speed T ouch™ Setup wizar d has detected y our SpeedT ouch™ device, you can pr oceed with the configuration procedur e .
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 29 5 As soon as the SpeedT ouch™ Setup wiza rd completed the update of the Speed- T ou ch™ configuration and reconfigur ed yo ur PC , following window will appear : Click Finish to close the wizard.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 30 Additional configuration Some additional configuration ma y be needed: • MS Windows IP configuration Most Service profiles will enable the SpeedT ouch™ DHCP server .
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 31 3.2 Operating System Independent SpeedT ouch™ Configuration Setup Suppor ted Systems As the SpeedT ouch™ is OS-indep endent, this configuration setup can be used fr om any computer system.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 32 Configuration of the SpeedT ouch™ Pro ceed as follows: 1 Open a web br owser and br owse to the SpeedT ouch™ web pages at http://10.0.0.138 . See “5 SpeedT ouch™ W eb Interface” on page 49 for more information.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 33 5 Easy Setup will update the SpeedT ouch™ configuration according to the Service profile.
3 SpeedTouch™ Configuration Setup E-DOC-CTC-20040123-0001 v3.0 34.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 35 4 SpeedT ouch™ Internet Connectivity Introduction This chapter provides inf ormation on how to configure y our S peedT ouch™ according to your pr efer ences and how to access the Internet.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 36 4.1 Internet Connections via SpeedT ouch™’ s Embedded PPP Dial-in Client Introduction The SpeedT ouch™ suppor ts both most popular con nection methods: PPP ov er A TM (PPP oA) and PPP ov er Ethernet (PPP oE).
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 37 4.1.1 Using the MS Windows XP Internet Gateway Device Control Agent Introduction MS Windows XP users can easily establish PPP sess.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 38 The connected Internet Gateway As long as the SpeedT ouch™’ s embedded PPP dial -in client is connected, you ar e able to ov e.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 39 4.1.2 Using the SpeedT ouch™ W eb Pages Introduction As the SpeedT ouch™ web pages are controllab le fr om any Operating System with a n installed web br owser , the method to esta blish PPP sessions described below can be used by any computer system.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 40 During the Internet session Y ou are able to ov er view and monitor your In ternet connectivity as long as the session is running via: • The SpeedT ouch™ System Information page See “ System Information” on page 53 .
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 41 4.2 Connect to the Internet via a Host PPPoE Dial- in Client Introduction This section explains how you can connect to the Internet usin g a Br oadba nd PPP oE dial-in application.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 42 4.2.1 Using an MS Windows XP BroadBand Connection Configuring a broadband connection Pro ceed as follows: 1 On the Start menu, click (Settings >) Control P anel . 2 The Contro l P anel window a ppears.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 43 6 In the next window , select Connect using a br oadband connection that requir es a user name and passw ord : Click Next to continue. 7 In the next window , give a name to th e connection you ar e creating, e.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 44 10 At the end of the configuration the following window a p pears: Click Finish to complete the configuration.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 45 T erminating a broadband Internet session Pro ceed as follows: 1 On the Start menu, point Connect T o and click the name of the connection you ’ve cre a te d e .
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 46 4.2.2 Using the Mac OS X PPPoE Dial-in Client Configuring a broadband connection Pro ceed as follows: 1 On the Apple menu, click System Pref erences . 2 The System Prefer ences window appears.
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 47 Star ting a broadband Internet session Pro ceed as follows: 1 Click the Internet Connect dockling. Note If the Internet Connect dockling is not a vailable , go to the Applica- tions folder on the system st artup disk and double-click Internet Connect .
4 SpeedTouch™ Internet Connectivity E-DOC-CTC-20040123-0001 v3.0 48.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 49 5 SpeedT ouch™ W eb Inter face Introduction The SpeedT ouch™ comes with integr ated configuration w eb pages. It allows you to configure y our S peedT ouch™ s imply by using a web bro w ser fr om an y local computer connected to the SpeedT ouch™.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 50 Access to the SpeedT ouch™ web interface via UPnP™ If your computer is UPnP™ enabled you can access the pages as follows: 1 Click (Settings >) Contr ol Panel on the Start menu to open the Contr ol Pa n el .
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 51 T opic menu and links On the left of each of the SpeedT ouch™ we b pages a topics menu is pr ovided. This menu na vigates you via links through all co nfigurational aspects of the SpeedT ouch™.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 52 Save all The Sav e All link on the menu allows y ou to sa ve the SpeedT ouch™ settings. It is advised to back-up your sa ved configurat ion on a regular basis. This can be done via the System link in the Advanced menu.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 53 5.1 Basic T ask Links System Information T he System Information page is the SpeedT ouch™ home page .
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 54 • Select System to view some important system information of the Sp eedT ouch™: The System ta ble lists: • The SpeedT ouch™ Product Name . • The unique Medium Access Control (M A C) addr ess of your SpeedT ouch™.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 55 Wirel ess The SpeedT ouch™ Wire less page offers thr ee tabs to configure the SpeedT ouch™5 80 wire less module: • Access point settings T o configur e the basic settings of the SpeedT ouch™580 wireless access point.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 56 • Rate shows the current modulation rate in which the SpeedT ouch™580 is curr ently operating. Note T ak e into consideration that if the distance between the Speed- T ou ch™580 and the client increases the thr ough put for this client decreases.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 57 • Select Framebursting to enhance the performance of wireless netw orks by impro ving the efficiency between the clie nt and the wireless access point if you ha ve mainly downstr eam traffic i.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 58 Security Select Security to: • Choose and configure a security le vel: By default all security is disabled.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 59 T o enable lev el 2 - WP A-PSK 1 Select the entr y Security lev el 2 - W P A-PSK which allows y ou to pr o- ceed with the f ollowi ng window: 2 Define your passphrase. Note The passp hrase must consist of 8 to 64 ASCII characters.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 60 T o disable an y security (No security) 1 Select the entr y Security le vel 0 which allows y ou to proceed wi th the fol- lowing windo w: 2 Click Apply to a pply y our changes. Note The colour of the WLAN LED will change to red.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 61 T o change the A CL Access mode, select the desired A CL Access mode from the dr opdownlist and click apply .
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 62 T o manuall y add a new station which can be done at any time. Pr oceed as follows: 1 Click New . 2 The following table is sh own: 3 Add an intuitiv e name for the wireless cli ent. 4 Add the wir eless client’ s physic al hardwar e addr ess (MA C addr ess).
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 63 Associated stations Select Associated Stations to view all wireless stations that are curr en tly associated to the SpeedT ouch™580 access point: T o add an associated station to the A CL: 1 Select the entr y you want to exp licitly add to the A CL.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 64 System Log Click this li nk to view the System Lo g page . This page allows you to view the activity on the Sp eedT ouch™ since pow er on: System log messages are used to pr ovide a historical o verview of ev ents, err ors, and messages generated during SpeedT ouch™ 580 operation.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 65 5.2 Advanced T opics Menu Links Diagnostics The Diagnostics page consists of three expandable sections: • Expand the System section to .
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 66 • Expand subsequently the Wa n , DSL and Connections sections to view the curr ent DSL state and connection information: Click to perform an IP connectivity test.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 67 Easy Setup Click this link to start the SpeedT ouch™ Easy Setup wizar d. See “3.2 Operating System Indepe ndent SpeedT ouch™ Configuration Setup” on page 31 for more i nform ati on.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 68 NAPT T he Netw ork Address and P or t T ranslation (NAPT) page allows y ou to: • View or ad d/delete specific static NAPT entries : T o add static NAPT entries pr oceed as follows: 1 Click New .
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 69 • Define a Default Server : By specifying a default ser v er IP addr ess (e .g. 10.0.0.154 as shown above), all incoming connections that don’ t match a specifically configured static NAPT entry will be forwarded to the device with this IP address.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 70 DHCP T he Dynamic Host Configur ation Pr otocol (DHCP) page allows you to: • Click The DHCP Ser ver tab to access the DHCP server pages.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 71 Under Pr operties, you ar e able to select: • DHCP ser ver Enables the SpeedT ouch™ DHCP ser ver .
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 72 • Click the DHCP Rela y tab to view the DHCP rela y pages. The DHCP rela y agent allows y ou to use DHCP clients and DHCP ser vers a vailable on differ ent networks.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 73 DNS T he Dynamic Name Syst em (DNS) page allows you to: • View the curr ent SpeedT ouch™ DNS ser ver hostname leases: Via this table you can also ad d static DNS hostname entries. This ma y be useful for de vices which do not suppor t DNS, e.
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 74 • Back up the curr ent SpeedT ouch™ conf iguration, restore the SpeedT ouch™ default configuration, or upload a backup configuration file: • T o backup the cu rr en t configuration click Backup and follo w the instruc- tions.
5 SpeedTouch™ Web In terface E-DOC-CTC-20040123-0001 v3.0 75 Enter User id and Pas swo rd (maximum 16 characters) of y our choice and r e-enter your pass w ord in the appr opriate field. Click Ap ply to a pply the System passw ord and Sa ve all to sa ve your changes to persistent memor y .
5 SpeedTouch™ Web Interface E-DOC-CTC-20040123-0001 v3.0 76.
6 SpeedTouch™ NAPT Manager E-DOC-CTC-20040123-0001 v3.0 77 6 SpeedT ouch™ NAPT Manager Introduction The SpeedT ouch™ Network Address P o rt T ran slation (NAPT) Manager is designed to simplify the configuration of the SpeedT ouch ™ NAPT engine .
6 SpeedTouch™ NAPT Manager E-DOC-CTC-20040123-0001 v3.0 78 3 The SpeedT ouch™ CD Bro wser menu appea rs: Click Configuration . 4 The following window appears: Click Configure NAPT Settings .
6 SpeedTouch™ NAPT Manager E-DOC-CTC-20040123-0001 v3.0 79 6 The Software License Agreement appea rs: Y ou must accept before continuing. Click Ye s to accept. Note If you accepted this Softwar e Lice nse Agreement in a pre vious session of NAPT Manager , this window will not be shown an ymore.
6 SpeedTouch™ NAPT Manager E-DOC-CTC-20040123-0001 v3.0 80 Configuration of the SpeedT ouch™ Pro ceed as follows: 1 As soon as the NAPT Manager has detected your SpeedT ouch™ device you can proceed with the configuration pr ocedure. Note The SpeedT ouch™ ma y be protected b y a system password.
6 SpeedTouch™ NAPT Manager E-DOC-CTC-20040123-0001 v3.0 81 • Manually ad d a static NAPT entries: Click the Advanced tab. Select a pr otocol in the Protocol list and enter Po r t and H ost IP addr ess in the appr opriate fields.
6 SpeedTouch™ NAPT Manager E-DOC-CTC-20040123-0001 v3.0 82 6 As soon as the NAPT Manager complete d the update of the SpeedT ouch™ NAPT configuration, following window wi ll appear : Click Finish to close the NAPT Manager . Note The NAPT manager allows y ou to de lete or modify configured NAPT mappings via the same procedur e .
7 Support E-DOC-CTC-20040123-0001 v3.0 83 7 Suppor t In this chapter This chapter contains t he following topics: To p i c P a g e SpeedT ouch™ W all Mount 84 SpeedT ouch™ System Softwar e Upgrade.
7 Support E-DOC-CTC-20040123-0001 v3.0 84 7.1 SpeedT ouch™ W all Mount W all mount The SpeedT ouch™580 can be wall-mounted by using tw o screws and the molded mounting bracke ts on the bottom of the SpeedT ouch ™580. Y ou must provide the scre ws.
7 Support E-DOC-CTC-20040123-0001 v3.0 85 7.2 SpeedT ouch™ System Software Upgrade Introduction This chapter describes how to upgrade the Sp eedT ouch™ system s oftwar e. System software updates (all OSs) For checking the a vailability of ne w system software v ersion packages: • Click the link, available on the SpeedT ouch™ CD Bro wser .
7 Support E-DOC-CTC-20040123-0001 v3.0 86 7.2.1 Upgrade via the SpeedT ouch™ Upgrade Wiza rd Introduction The procedur es described in this section are valid only in case: • Y ou run a MS Windows Operating System or Mac OS X.
7 Support E-DOC-CTC-20040123-0001 v3.0 87 3 The SpeedT ouch™ CD Bro wser menu appea rs: Click Diagnostics & Maintenance . 4 The following window appears: Click Upgrade My SpeedT ouch™ .
7 Support E-DOC-CTC-20040123-0001 v3.0 88 On Mac OS X Proceed as f ollows: 1 Insert the SpeedT ouch™ Setup CD-R OM in your PC's CD-R OM driv e. 2 Open the CD-R OM and bro wse to the osx fold er . 3 In the osx folder double-click upgradeST .pkg to install the SpeedT ouch™ Upgrade application.
7 Support E-DOC-CTC-20040123-0001 v3.0 89 Upgrade procedure 1 The W elcome to the SpeedT ouch™ Upgrade Wizard window appears: Click Ne xt . 2 The SpeedT ouch™ Software License Agr eement window a ppears: Y ou must accept before continuing. Click Ye s to accept.
7 Support E-DOC-CTC-20040123-0001 v3.0 90 4 The SpeedT ouch™ Setup Wizard should fi nd y our SpeedT ouch™ device on the local netw ork. This is indicated by t he followi ng window: If mor e than one device is f ound, a list of a vailable devic es will be pro vided.
7 Support E-DOC-CTC-20040123-0001 v3.0 91 8 The following window allows you to ov er view y our selection: Click Next to continue. 9 Y ou can follow the upgrade pr ogress in follow ing window: 10 After upgrading the SpeedT ouch™, a final window a ppears to announce that the upgrade has been successful Click Finish to close the wizard.
7 Support E-DOC-CTC-20040123-0001 v3.0 92 System software downgrade Via the identical procedur e it is also possi ble - although not recommended - to down- grade the SpeedT ouch™ by uploading an ol der system software than the curr ent running version.
7 Support E-DOC-CTC-20040123-0001 v3.0 93 7.2.2 Manual System Software Management via BOOTP Ser ver SpeedT ouch ™ system software management The SpeedT ouch™ system software is base d on BOO TP , a standard mechanism used for booting diskless stations.
7 Support E-DOC-CTC-20040123-0001 v3.0 94 Procedure T o upgrade/restore the SpeedT ouch™ system software: 1 In a preliminary s tep , make sure that y our SpeedT ouch™ is pow ered off and that a BOO TP ser v er is readil y installed on the computer from which y ou intend to per- form the system software upgrade.
7 Support E-DOC-CTC-20040123-0001 v3.0 95 7.3 SpeedT ouch™ Default Configuration Reset to default configuration Pro ceed as follows: 1 Mak e sure the SpeedT ouch™ is pow ered on. 2 Use a pencil to pr ess and hold for 7 seconds the recessed r eset bu tton ( A ) at the SpeedT ouch™.
7 Support E-DOC-CTC-20040123-0001 v3.0 96 7.4 UPnP™ on Windows XP Systems Adding UPnP™ If you ar e ru nning Micr osoft Windows XP , it is r ecommended to add the UPnP™ component to y our system. Pro ceed as follows: 1 On the Start menu, click Contr ol P anel .
7 Support E-DOC-CTC-20040123-0001 v3.0 97 Adding Internet Gateway Device Discover y and Control Y our MS Windows XP system is able to di scov er and contr ol Internet Gatewa y Devices (IGD), lik e the SpeedT ouch™580 on y our loca l network. Theref ore it is r ecommended to add the IGD Discov er y and Control client to y our system.
7 Support E-DOC-CTC-20040123-0001 v3.0 98 7.5 T roubleshooting Configuration problems In case y our SpeedT ouch™ is unreachable due to misconfiguration, you might consider a hardwar e r eset to factor y defaults as described in “7.3 SpeedT ouch™ Defa ult Config- uration” on page 95 .
7 Support E-DOC-CTC-20040123-0001 v3.0 99 LAN LED does not light up. Link integrity/Activity LED of Ethernet port does not light up . Mak e sur e that the LAN cable are secur ely connected to the 10/100Base-T port. Mak e sure that y ou are using the corr ect cable type for your Ethernet equipment.
7 Support E-DOC-CTC-20040123-0001 v3.0 100.
.
© 2004 THOMSON. All rights r e served. E-DOC-CTC-20040123-0001 v3.0 Need more help? Additional help is a vailabl e online at www .speedtouch.com ..
An important point after buying a device RCA 580 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RCA 580 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RCA 580 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RCA 580 you will learn all the available features of the product, as well as information on its operation. The information that you get RCA 580 will certainly help you make a decision on the purchase.
If you already are a holder of RCA 580, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RCA 580.
However, one of the most important roles played by the user manual is to help in solving problems with RCA 580. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RCA 580 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center