Instruction/ maintenance manual of the product 4-Port USB 2.0 Device Server over IP USBN-500 Quatech
Go to page of 18
Quatech Model USBN-500 Network USB2.0 Device Server Over IP 4-Port USB2.0 Device USER MANUAL.
USB Device Server Windows Client User Manual TABLE OF CONTENTS 1. Introduction______________________________________________________________3 2. Windows utility____________________________________________________________3 2.1. Virtual USB-IP Driver Software_________________________________________4 2.
2. Windows utility USBIP Admin utility Setup is an Install Shield ba sed application, which can be used for installing, uninstalling and upgrading this USB device server Client S/W. Pl ease run the self-explanatory Install shield application to install this USB device se rver Admin Utility.
USBIP Admin tool The application has four panels, wh ich are docked in the application. 1) Main window: This displays all the Device server and the USB Devices connected on them 2) Function Panel: This panel enables to switc h between the Device Mapping and Server Manager Application.
and the Operating System autom atically searches for the driver until the Virtual USB over IP driver is installed. Make sure that you click on “Continue anyway” if a Windows dialog pops up about the Digital Signature as shown below.
2.3. Server Manager Server manager enables the Administrator to c onfigure the USB device server on the network. The Server Manger also has an option to s earch for the USB servers on the Network. Right Click on Server Manager Main window and Click on “Search server” as shown below.
It pops up the ‘Searching for Servers’ dialog and li st all the USB device se rvers on the Network as shown below The USB Device Server search is password protected and should be unlocked in order to configure the selected device.
On selecting ‘Un-Lock’ the password dialog pops up as shown below. Key in the password in the ‘Password’ dialog. The default password for the USB IP Server is “usbip” If the Authentication is successful a ‘Unlock OK’ dialog appears. Now the Device server can be configured for various settings as given below.
The Basic Settings page allows you to specify a server name .Check the modify box and enter server name as shown below. IP Settings Page: The IP Settings page allows you to modify the US B device server IP Address as shown below. The Default IP Address is 192.
After Selecting IP Configuration key in the IP Ad dress of the USB device server in the IP Address field followed by proper Subnet Mask & Gate Way as shown below. After entering IP address, Subnet Mask & Gate Way then click on “save” button.
Check the Modify box to Enable or Disable password option to the USB device server. b) Upgrade Firmware This USB device server Firmware can be upgraded remotely using the Firmware upgrade option. Select the server on the Server manager. Right Click on the server and Select Upgrade Firm ware option to upgrade the firmware.
As soon as the transfer is completed, the USB de vice server automatically restarts to apply the upgraded firmware settings. c) Restore factory defaults Right click on the USB device server under Serv er Manager Window and select the Restore Factory Defaults function to obtain Default settings as shown below.
the Printer Auto Reconnect button on the Menu bar to open the Printer Auto-Connect Window. Select the Printer which was connected a nd Click on “Save” and close the Window.
browser, which will displays the default hom e page of the Server. Def ault IP address is 192.168.3.22, for USB Server application & the USB devi ce server will have this IP address when USB Server Firmware is loaded on to it. http://192.168.3.22 On password prompt please give ‘ admin ’ as user name and ‘ usbip ’ as password.
For the wired interface you can configure the Stat ic IP, Subnet Mask, and Gateway m anually or set the box to automatically obtain an IP address by setting to the Dyna mic (DHCP) mode. 3.4. Status Page The status page displays the current status of the USB devices attached.
a ) T h r e a d S t a t u s : T h r e a d S e s s i o n H o s t A c t i o n b ) S e r v i c e S t a t u s : S e r v i c e S t a t u s C o n t r o l c ) D e v i c e S t a t u s : Vendor Id Product Id C.
An upgrade.tar.bz2 file is required to upgrade the firmware. Click on “upgrade” to upgrade the firmware.
A file successfully uploaded message is displaye d and the webpage also indicates that the USB device server is restarting to a pply the upgraded firmware settings.
An important point after buying a device Quatech 4-Port USB 2.0 Device Server over IP USBN-500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Quatech 4-Port USB 2.0 Device Server over IP USBN-500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Quatech 4-Port USB 2.0 Device Server over IP USBN-500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Quatech 4-Port USB 2.0 Device Server over IP USBN-500 you will learn all the available features of the product, as well as information on its operation. The information that you get Quatech 4-Port USB 2.0 Device Server over IP USBN-500 will certainly help you make a decision on the purchase.
If you already are a holder of Quatech 4-Port USB 2.0 Device Server over IP USBN-500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Quatech 4-Port USB 2.0 Device Server over IP USBN-500.
However, one of the most important roles played by the user manual is to help in solving problems with Quatech 4-Port USB 2.0 Device Server over IP USBN-500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Quatech 4-Port USB 2.0 Device Server over IP USBN-500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
