
SFE23RE-W SFE23RE-C SFE23RE-O
SFE33RE-W SFE33RE-C SFE33RE-O
SFE23RE-DO
SFE33RE-DO
Freestanding Electric Fireplace
Installation Instructions and Owner’s Manual
MAY RESULT CAUSING PROPERTY, PERSONAL INJURY OR LOSS OF LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS
OTHER APPLIANCE
ANSI/UL1278. MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS INSTALLER: DO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER


When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
remove plug from outlet.
electric shock, and injury to persons, including the
following:
cally grounded in accordance with local codes with
the current CSA C22.1 Canadian local codes for
burns, do not come in contact with heater. Keep
USA installations. Follow local codes and National
combustible materials, such as furniture,
Electrical Code, ANSI/NFPA NO.70 and Canadian
pillows, bedding, papers, clothes, and curtains
Cord: CZ 22.2 NO.0.
at least 3 feet(1m.) from the front of the heater.
ventilation or exhaust opening as this may cause
is used by or near children or invalids and when-
electric shock, fire or damage to the heater.
ever the heater is left operating and unattended.
or exhaust in any manner. Do not use on soft
surfaces, such as a bed, where openings may
or plug or after the heater malfunctions, has
become blocked.
been dropped or damaged in any manner.
that sparks and arcs. Do not use it in areas where
out by a qualified service person.
gasoline, paint, or flammable liquids are used or
stored.
place be modified. Parts having to be removed
for servicing must be replaced prior to operat-
Other uses not recommended by the manufac-
ing this electric fireplace again.
turer may cause fire, electric shock, or injury.
overheat and cause a risk of fire. However if you
laundry areas or similar indoor locations. Never
must use an extension cord, the cord shall be No.
use this appliance near a bathtub or other wa-
14AWG minimum size and rated not less than 1900
ter container.
watt. The extension cord must be a three wire cord
with grounding type plug and cord connector.
cord with throw rugs, runners or similar
coverings. Arrange cord away from traffic areas
as a drying rack for clothing. Also, do not hang
and where it will not be tripped over.
Christmas stockings or decorations on or near it. 20.SAVE THESE INSTRUCTIONS.

WARNING: Electrical outlet wir-
Your new freestanding electric fireplace may be installed vir-
ing codes and all other appliable
tually anywhere in your home. However when choosing a
location for your new electric fireplace, ensure that the gen-
eral instructions are followed. For best effect results, install
fire, electrical shock and injury.
the electric fireplace out of direct sunlight.
CLEARANCE TO COMBUSTIBLES
place if any part of it has been
Sides 0 mm 0 inches
Floor 0 mm 0 inches
spect the fireplace and replace
Top 0 mm 0 inches
ELECTRICAL CONNECTION
if necessary.
A 15 AMP, 120 Volt,60Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit. Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is on operation. The unit comes standard with a 6’ (1828mm) long three wire cord exiting from the rear of the fireplace. Plan the installation to avoid the use of an extension cord. If an extention cord must be used, it must be a minumum 14 AWG three wire with grounding type plug connector and rated no less than 1900 Watts.The cord shall not be more than 20 feet in length.
attempting any maintenance or clean-
ing to reduce the risk of fire, electri-
cal shock or personal injury.
This fireplace uses four clear 120 Volt, 60 Watt, E- 12 socket base light bulbs (small base, chandelier candle type).The 60 Watt bulbs are located under the log set/ember bed. For convenience, if one of the bulbs burns out, it may be a good idea to re- place all of the light bulbs.
Watts per bulb. The use of
higher rated bulbs may result
in a fire causing property
damage and personal injury.

GLASS INFORMATION
The motors used on the fan and flame genera-
tor assembly are prelubricated for extended
operated with missing or broken glass.
bearing life and require no further lubrication.
However, periodic cleaning/vacuuming of the
fan/heater unit is recommended.
facturer and replacement should be carried out
power is turned off before
by a qualified service person.
proceeding.
Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance
with national and local codes.
If repairing or replacing any electrical component or wiring, the original wire
routing, color coding and securing location must be followed.
Model: SFE23RE, SFE33RE Voltage: 120 VAC, 60 Hz Total Amps: 11.5 Amps Total Watts: 1380 Watts Heater Rating: 1200 Watts
Heater Element 16AWG
Other Wire 18AWG

Before programming your transmitter you must first insert three triple “AAA” batteries. Make sure the main power on/off swith is in “ON” position. 1. The Mode setting: Press the “SET” button, then the “AUTO” light will flash. Press the “SET” button again, and then the “MANUAL” light will also flash. The “AUTO” light and the “MANUAL” light will flash alternately and continuously. Next press “EN- TER” button to select the auto mode or manual mode.
a. When selecting “AUTO” mode:
Select “AUTO” and press the “ENTER” button to activate , then press the “SET” button, next the ‘Temperature’, ‘Flame’, ‘Light’, ’lamp’ sym-
bols will flash alternately. Next press the
button to select the desired
temperature setting. When the temperature setting has been selected, press the “SET” button to lock in the temperature setting, next set the following functions that appear on the transmitter. When the last function setting has been completed, press the “ENTER” button, and the symbols will stop flashing. b. When selecting “MANUAL” mode:
Select “MANUAL” and press the “ENTER” but- ton to confirm, then press the “SET” button, the ‘Flame’, ‘Light’, ‘lamp’, ‘Heating level’ sym- bols will flash alternately. The next symbol will flash automatically set the functions as they appear. When the last function setting has been completed, press the “ENTER” button, and the symbols will stop flashing.
Remote Control Front Remote Control Back
Heater Front View · button or the

flash. Press
to set the hour. After the hour has
been set, press the “CLOCK” button again to set the minutes. After the minutes has been set, press the “CLOCK” button, the clock will indicate the set time.
button, for faster flame effect, press
button.
(2) Flame brightness Press “SET” button, when the lamp symbol flashes,
button to decrease the flame brightness
the transmitter, next press
to adjust the time, to
button to increase the flame brightness.
add 30 minutes increments press the button again. After the timer has been set, press “TIMER” button again, the word “TIMER” will flash and the timer will return to time.
To lock, press the “LOCK” button, there will be a
symbol, which means that the transmitter is in a lock position. To
once immediately followed by pressing
the “LOCK” button .
“ symbol will flash. Then
to select full, half or no heating.
(Adaptor NOT permitted in Canada) Under CZ22.2 NO. 0 standard

Model: SFE23RE-W (-C, -O, -DO) Voltage: 120V/60HZ Total Amps: 11.5A Total Watts: 1380W Heating Ratings: 1200W Dimensions, Inches (H x W X D)
Model: SFE33RE-W (-C, -O, -DO) Voltage: 120V/60HZ Total Amps: 11.5A Total Watts: 1380W Heating Ratings: 1200W Dimensions, Inches (H x W X D)
Fireplace 38x39 1/2x15 5/8
Fireplace 43 1/2 x 52 3/4 x 16 15/16
Carton 42 1/2x41 3/8x17 5/16
Weight, Pounds Fireplace 98
Weight, Pounds Fireplace 210

* -X represents -W(White), -C(Cherry), -O(Oak), -DO(Dark Oak)
when ordering

Installing logs for SFE33RE:
FIG 5 - Logs for SFE33RE
FIG 2
1.Insert the two pins on log 1 to the two recessed holes at the middle of grate. (See FIG 2).
1.Place log 1, log 2 and log 3 into the correspond- ing holes on grate. (See FIG 6).
4 1 2 3
FIG 7
2.Insert the pin on one end of log 2 to the recessed hole on log 1, with the other end of log 2 placed on the ember bed (where marked). (See FIG 3).
2.Insert the pin on one end of log 4 to the recessed hole on log 1, with the other end of log 4 placed where marked. (See FIG 7).
4 1 2 5 3
FIG 4
3.Insert the pin on one end of log 5 to the recessed hole on log 2, with the other end of log 5 placed where marked. (See FIG 8).
3.Place one end of log 3 onto the hole on grate, with the other end placed on log 1 (where marked).
(See FIG 4).
6 4 1 2 5 3
4.Insert the pin on log 6 to the recessed hole on log 4, and place log 6 as figure shows. (See FIG 9).


Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.