EN
Official user manual

Powercom 325A

17 pages·51 KB·Power Supply·PDF·ENDEFRITNLJA
Powercom 325A
Table of Contents 28 sections U P S · Uninterruptible Power System · Line Interactive UPS 325A/425A/525A/625A · Line Interactive Network UPS 425AP/525AP/625AP · … ShowHide
Page 1 of the Powercom 325A user manual — Uninterruptible Power System
Page 1 · click to enlarge
Page 1

U P S

Uninterruptible Power System

Line Interactive UPS 325A/425A/525A/625A

Line Interactive Network UPS 425AP/525AP/625AP

USER‘S MANUAL

Page 2 of the Powercom 325A user manual — Please save or recycle the packaging materials!
Page 2 · click to enlarge
Page 2

Please read this manual!

This manual provides safety, installation and operating instructions that will help you derive the fullest performance and service life that the UPS has to offer.

Please save this manual!

It includes important instructions for the safe use of this UPS and for obtaining factory service should the proper operation of the UPS come into question.

Please save or recycle the packaging materials!

The UPS‘s shipping materials were designing with great care to provide protection from transportation related damage. These materials are invaluable if you ever have to return the UPS for service. Damage sustained during transit is not covered under the warranty.

Page 3 of the Powercom 325A user manual — Please read this manual!
Page 3 · click to enlarge
Page 3
Page 3 of the Powercom 325A user manual — Please read this manual!
Page 4 of the Powercom 325A user manual — 1. INTRODUCTION __________________________________________________________ _____
Page 4 · click to enlarge
Page 4

1. INTRODUCTION

The product is line interactive UPS with the newest technology and powerful function. The LINE INTERACTIVE ups is with AVR function allows input voltage range from 75% to 125%, including on line voltage boost-up & buck down. An ideal protection equipment for critical connected loads. It is based on microprocessor controls, with utility power connected, the charging is ongoing, no need to switch ON the UPS and at back-up mode, UPS can be automatically turned OFF if none of the connected loads is operating to save the battery energy. The indicator will be ON when battery needs replacement and a cyclic self-testing function is included in order to verify both the operation of the UPS and the condition of the battery.

In addition, This UPS provides advanced single telephone line or modem surge suppression through the modular connectors on the back panel.

The LINE INTERACTIVE UPS and UPSMON monitoring software (optional kits) makes your computer operate intelligent and provides you with the ability of perfect protection of your critical devices.

  • Note: There is no guarantee that interference to radio/TV will not occur in a particular installation. If this UPS causes interference to radio or television reception, which can be determined by turning the UPS off and on, the user is encouraged to try to correct the interference by one or more of following measures:
  • connect the equipment to an outlet on a circuit different from that to which the receiver is connected
  • increase the separation between the equipment and the receiver
  • reorient the receiving antenna
Page 5 of the Powercom 325A user manual — CAUTION !
Page 5 · click to enlarge
Page 5

2. Safety

CAUTION !

  • To reduce the risk of electric shock, disconnect the UPS from the mains supply before installing a computer interface signal cable. Reconnect the power cord only after signaling interconnections have been made.
  • The internal energy source(the battery) cannot be de-energized by the user. The output may be energized when the unit is not connected to a mains supply.
  • The right way to de-energize the UPS properly in an emergency is to move the I/O switch to the OFF position and disconnect the power cord from the mains supply.
  • The socket-outlet shall be installed near the equipment and easily accessible.
  • Attention, hazardous through electric shock. Also with disconnection of this unit the main, hazardous voltage still may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole when maintenance of service work inside the UPS is considered.
  • Do not dispose of batteries in a fire, the battery may explore.
  • Do not open or mutilate the battery, released electrolyte is harmful to the skin and eyes.
  • A battery can present a risk of electric shock and high short circuit current. The following precaution should be observed when working on batteries - Remove watches, rings or other metal objects. - Use tools with insulated handles.
Page 6 of the Powercom 325A user manual — FRONT PANEL
Page 6 · click to enlarge
Page 6

3. Presentation

FRONT PANEL

3.1 "REPLACE BATTERY" indicator (RED LED) The LED illuminates when the UPS's battery is no longer useful and must be replaced.

3.2 "BACK UP" indicator (YELLOW LED) The LED illuminates when the UPS is supplying battery power to the loads.

3.3 "LINE NORMAL" indicator (GREEN LED) The LED illuminates when the line input voltage is normal.

3.4 "ON/OFF/TEST/SILENCE" button Press the button more than 3 seconds to turn the UPS on or off, press the button less than 1 second to activate the UPS's self-testing or silence the back up alarm.

Powercom 325A — FRONT PANEL diagram (page 6)
Fig. 1
Page 7 of the Powercom 325A user manual — 3.6 OUTPUT POWER RECEPTACLES
Page 7 · click to enlarge
Page 7

REAR PANEL

3.5 COMPUTER INTERFACE (425AP/525AP/625AP models only) Provide both RS-232 and relay signal to support NOVELL, UNIX, DOS, WINDOWS and other operating systems.

3.6 OUTPUT POWER RECEPTACLES

3.7 AC INPUT POWER RECEPTACLE

3.8 TEL./MODEM SURGE PROTECTION (425AP/525AP/625AP models only) Surge protection for telephone and modem line to have the complete safety connection for INTERNET service.

Page 8 of the Powercom 325A user manual — 4. Installation __________________________________________________________ ____
Page 8 · click to enlarge
Page 8

4. Installation

4.0 Inspection Inspect the UPS upon receipt. The packaging is recyclable; save it for reuse or dispose of it properly.

4.1 Placement Install the UPS in a protected area with adequate air flow and free of excessive dust. Do not operate the UPS where the temperature and humidity is outside the specified limits.

4.2 Connect Computer Interface (425AP/525AP/625AP models only) UPSMON (or other power management software) and an interface kits can be used with this UPS. Use only kits supplied or approved by the manufacturer. If used, connect the interface cable to the 9 pin computer interface port on the back panel of the UPS. Note: Computer interface connection is optional. The UPS works properly without a computer interface connection.

4.3 Connect to Utility Connect the AC input power connector to utility power to power up the UPS.

4.4 Charge the battery The UPS charges its battery whenever it is connected to utility power. For best results, charge the battery for 4 hours in the initial use.

Powercom 325A — 4. Installation __________________________________________________________ ____ diagram (page 8)
Fig. 2 · 4. Installation ____________________________________…
Page 9 of the Powercom 325A user manual — 4. Installation __________________________________________________________ ____
Page 9 · click to enlarge
Page 9

4.5 Connect the loads Plug the loads into the output connectors on the rear of the UPS. To use the UPS as a master on/off switch, make sure all of the loads are switched on. Caution: Never connect a laser printer or plotter to the UPS with other computer equipment. A laser printer or plotter periodically draws significantly more power than when idle, and may overload the UPS. 4.6 Connect the telephone/modem lines (425AP/525AP/625AP models only) Connect a single line telephone or a modem line into the telephone/modem surge protection sockets on the back of the UPS. The RJ-45/RJ-11 modular sockets accept standard single line telephone connections. This connection will require another length of telephone cable (supplied).

Page 10 of the Powercom 325A user manual — 5. Operation __________________________________________________________ ____
Page 10 · click to enlarge
Page 10

5. Operation

5.1 Switch on With the UPS plugged in, press and hold the on/off/test/silence button more than 1 second until "LINE NORMAL" LED lit to switch the ups on. The UPS will perform self-testing each time when it is switched on.

5.2 Switch off By pressing and hold the on/off/test/silence button more than 3 seconds until the "LINE NORMAL" or "BACK UP" LED off.

5.3 SELF-TEST Use the self-test to verify both the operation of the UPS and the condition of the battery. In normal utility power, push the on/off/test/silence button less than 1 second and UPS performs a self-test function. During the self-test, the UPS operates a back up mode.

Note: During the self-test, the UPS briefly operates the loads on-battery (the on-battery LED comes on). If the UPS passes the self-test, it returns to on-line operation. The on- battery LED does off and the on-line LED goes on steady. If the UPS fails the self-test it immediately returns to on-line operation and lights the replace battery LED. The loads are not affected. Recharge the battery overnight and perform the self-test again. If the replace battery LED is still on, ask our nearest dealer to replace battery.

5.4 SILENCE In "BACK UP" mode, push on/off/test/silence less than 1 second to silence the audible alarm. (The function is void when under condition of "LOW BATTERY" or "OVERLOAD")

Page 11 of the Powercom 325A user manual — 6. Alarm __________________________________________________________ _____
Page 11 · click to enlarge
Page 11

6. Alarm

6.1 "BACK UP" (slow alarm) When in BACK UP mode, the YELLOW LED illuminates and the UPS sounds an audible alarm. The alarm stops when the UPS returns to LINE NORMAL operation. Press the on/off/test/silence button during on-battery alarms to stop the beeping.

6.2 "LOW BATTERY" (rapid alarm) In BACK UP mode, when the battery energy runs low, the UPS beeps rapidly until the UPS shuts down from battery exhaustion or returns to LINE NORMAL operation.

6.3 "OVERLOAD" (continuous alarm) When the UPS is overloaded (the connected loads exceed the maximum rated capacity) the UPS emits continuous alarm to warn a overload condition. Disconnect nonessential load equipment from UPS to eliminate the overload.

Page 12 of the Powercom 325A user manual — 7. Software options __________________________________________________________ ____
Page 12 · click to enlarge
Page 12

7. Software options

7.1 UPSMON Software The UPSMON software is applied standard RS-232 interface to perform monitoring functions, and then provides an orderly shutdown of a computer in the event of power failure. Moreover, UPSMON displays all the diagnostic symptoms on monitor, such as Voltage, Frequency, Battery level and so on..

The software is available for DOS, Windows 3.1x, Windows 95 & Windows NT V3.5 or later.

7.2 Interface Kits A series of interface kits is available for operation systems that provide UPS monitoring. Each interface kit includes the special interface cable required to convert status signals from the UPS into signals which individual operating system recognize. The interface cable at UPS side must be connected to REMOTE PORT , at computer side can be either COM 1 or COM 2. The other installation instructions and powerful features please refer to READ.ME file.

Page 13 of the Powercom 325A user manual — 8. Computer Interface Port __________________________________________________________ ____
Page 13 · click to enlarge
Page 13

8. Computer Interface Port

The computer interface port has the following characteristics:

Powercom 325A — 8. Computer Interface Port __________________________________________________________ ____ diagram (page 13)
Fig. 3 · 8. Computer Interface Port _________________________…
Page 14 of the Powercom 325A user manual — 9. Battery Replacement __________________________________________________________ ____
Page 14 · click to enlarge
Page 14

9. Battery Replacement

  • Your battery should run any where from 3-5 years before eve needing to be replaced. Please follow the instructions below for easy battery replacement. 1) Unplug unit from AC power source and disconnect all connected equipment. 2) Disconnect AC power cord from unit.. 3) Turn unit upside down and using a phillips screw driver, unscrew the 4 screws holding the top of the unit to the bottom. Put screws in a safe place for reconnection. 4) Holding the top together firmly with the bottom, turn the entire unit right side up. 5) Carefully lift top cover off and place to the side. The connecting wires and electronics will be exposed. Be careful not to touch any inner components when changing the battery. 6) Remove the 2 connecting wires from the battery. 7) You can now easily remove the battery from the unit Caution: Do not dispose of battery in fire. Caution: Do not attempt to open the battery. Caution: The following precautions should be taken when replacing the battery
  • remove watches, rings, etc…
  • use tools with insulated handles 8) Place your new battery in the same position/direction and reconnect the wires red wire-position(+) and black wire negative(-) 9) Please follow steps 5,4 and 3 (in that order) to reconnect the entire unit. 10) Please follow manual instructions in order to properly reconnect your equipment.
Page 15 of the Powercom 325A user manual — 10. Troubleshooting __________________________________________________________ ____
Page 15 · click to enlarge
Page 15

10. Troubleshooting

Powercom 325A — 10. Troubleshooting __________________________________________________________ ____ diagram (page 15)
Fig. 4 · 10. Troubleshooting ________________________________…

PROBLEM POSSIBLE CAUSE ACTION TO TAKE On/off/test/silence button not pushed or push too short

Battery voltage less than 10V Recharge the ups at least 4 hours

Power cord lose Replug the power cord AC FUSE burn out Replace the AC fuse Line voltage too high, too low or black out

PCB failure Replace PCB, call for service battery not fully charged Recharge the UPS at least 4 hours Back up time too short PCB failure Replace PCB, call for service Buzzer continuous beeping

RED LED light Battery failure Replace battery, call for service

Page 16 of the Powercom 325A user manual — PROTECTION
Page 16 · click to enlarge
Page 16

11. Storage

10.1 Storage conditions Store the UPS covered and upright in a cool , dry location, with its battery fully charged. Before storing, charger the UPS for at least 4 hours. Remove any accessories in the accessory slot and disconnect any cables connected to the computer interface port to avoid unnecessary draining the battery.

10.2 Extended storage During extended storage in environments where the ambient temperature is -15 to +30 ℃ (+5 to +86 ℉), charge the UPS‘s battery every 6 months. During extended storage in environments where the ambient temperature is +30 to +45 ℃ (+86 to +113 ℉), charge the UPS‘s battery every 3 months.

12. Specifications

MODEL 325A 425A(P) 525A(P) 625A(P) Capacity 325VA 425VA 525VA 625VA Voltage 100V, 110V, 120V, 220V, 232V, 240V, +/-25% INPUT

Frequency 50 or 60Hz +/-5% (auto sensing) Voltage (on battery)

OUTPUT

Simulated sine wave at Line Input +/-5%

50 or 60Hz +/-0.5%

AVR automatically increase output voltage 15% above input voltage if -9% to-25% of nominal. AVR decrease output voltage

13% below input voltage if+9% to 25% of nominal

Transfer Time 2/4 milliseconds, including detection time Spike Protection 320 joules, 2ms

PROTECTION

EMI/RFI filter 10dB at15MHz, 50dB at 30MHz (for xxxAP models only) Overload Protection

UPS automatic shutdown if overload exceeds 110% of nominal at

60 second and 130% at 3 seconds. Unit Input Fuse for overload & short circuit protection 10Baase-T Cable Port

Network (UTP, RJ-45) compatible jacks

(for xxxAp models only)

Short Circuit UPS output cut off immediately or input fuse protection BATTERY Type Sealed, maintenance-free lead acid

Frequency (on battery) · Voltage Regulation AVR · and FILTERING

Page 17 of the Powercom 325A user manual — 11. Storage __________________________________________________________ ____
Page 17 · click to enlarge
Page 17
Powercom 325A — 11. Storage __________________________________________________________ ____ diagram (page 17)
Fig. 5 · 11. Storage ________________________________________…

indicator Back up Time 10 - 30 minutes (depending on computer load) Net Weight

6,000 meters max. elevation, 0-95% humidity non-condensing 0-48 deg C Audible noise

©1997 Powercom Co., Ltd. All right Reserved. All trademarks are property of their respective owners. Specifications subject to change without notice.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
UPS not on LED not lightOn/off/test/silence button not pushed or push too shortPress the on/off/test/silence button more than 1 second p.15
UPS not on LED not lightBattery voltage less than 10VRecharge the ups at least 4 hours p.15
UPS not on LED not lightPCB failureReplace the PCB, call for service p.15
UPS not on LED not lightLoad less than 20W at battery modeNormal condition p.15
UPS always at battery modePower cord loseReplug the power cord p.15
UPS always at battery modeAC FUSE burn outReplace the AC fuse p.15
UPS always at battery modeLine voltage too high, too low or black outNormal condition p.15
UPS always at battery modePCB failureReplace PCB, call for service p.15
Back up time too shortbattery not fully chargedRecharge the UPS at least 4 hours p.15
Back up time too shortPCB failureReplace PCB, call for service p.15
Buzzer continuous beepingOverloadRemove the noncritical loads p.15
RED LED lightBattery failureReplace battery, call for service p.15

Ask about the Powercom 325A

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Powercom 325A

Be the first to ask — other owners or our team will answer.

Original document

Powercom 325A manual PDF

17 pages·51 KB·Power Supply·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…