Instruction/ maintenance manual of the product I-Fly i I-Fly Wireless Access Point Atlantis Land
Go to page of 42
i I-Fly Wireless Access Point User’s Manual (V1.0).
COPYRIGHT The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned mat be trademarks or registered tradem arks of their respective owners. S ubject to change without notice. No liability for technical errors and/or omissions.
INDEX CHAPITER 1 ............................................................................................................. 1 1.1 A N O VERVIEW OF THE I-F LY W IRELESS A CCESS P OINT .................................................................
APPENDIX B ........................................................................................................... 32 T ECHNICAL F EATURES ............................................................................................................
1 Chapiter 1 Introduction And' besides available on CDRom a Quick Start Guide for a fast configuration. 1.1 An Overview of the I-Fly Wireless Access Point The device for a total freedom of movem ent without losing the conn ection.
1.3 I-Fly Wireless Access Point Features I-Fly Wireless Access Point prov ides the following features: • Interoperable with IEEE802.11g and IEEE802.11b • Atheros Super G™ capabilities to delive r 108 Mbps raw data rates and 90 Mbps TCP/IP throughput for 802.
3 ● Enables remote access to corporate network info rmation, for example e-m ail and the company home page.
4 Chapiter 2 Using I-Fly Wireless Access Point 2.1 Cautions for using the I-Fly Wireless Access Point Do not place the AP under high humidity and high temperature. Do not use the same power source for AP with other equipm ent. Do not open or repair the case yourself.
5 2.4 Cabling The most common problem is bad cabling. Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs.
Chapiter 3 Configuration The I-Fly Wireless Access Point can be configured with your Web browser. The web browser is included as a standard application in the fo llowing operation systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/Me/XP, and etc. The product provides a very easy and user-friendly interface for configuration.
7 3.3 Test TCP/IP After configuring the TCP/IP protocol, you can use the ping command to check if your computer has successfully connected to this AP. The following example shows the ping procedure for Windows 98 . First, execute the ping command. Ping 192.
3.5 Factory Default Settings Before configurating this AP, you need to know the following default settings. Web Configurator Username : admin Password: admin Device IP Network settings in LAN site IP Address : 192.168.1.1 Subnet Mask : 255.255.255.0 DHCP server : DHCP server disable Wireless Channel= 6 WEP/WAP= disable 3.
9 The below window will popup. Please enter the user name and password. Both of the default is “ admin ”. Now, the main menu screen is popup..
At the configuration homepage (if Quick Setup Wiz ard starts, please close it or read the printed Quick Start Guide), the left na vigation page where bookmarks are provided links yo u directly to the desired setup page, including: • Wizard • Status • Basic Setting • IP Setting • Advanced Setting • Security • 802.
11 • Wireless: Shows the Mac address, current ESSID, the st a tus of Encryption Function (Enable o r Disable), the current u sing channel. The current wireless tra ffic calcul ated in terms of number of p ack ets sen t an d re cei ved by AP through wireless communication is also displayed.
• AP Name: The name of the AP, which can be us ed to identify the Access Point among the all the Access Points in the wireless network. • SSID: Service Set Identifier, which is a unique name shared among all clients and n o d es i n a wireless network.
13 3.7.3 IP Settings This page allows you to configure the IP and DHCP settings of the Access Point. The default IP address of this access point is 192.168.1.1 with the subnet mask of 255.255.255.0 . You can type in other values for IP Addr ess, Subnet Mask and Gateway and click “ Apply ” button for the changes to be effective.
3.7.4 Advanced Setting This page contains configuratio ns for advanced users, which th e change refle cts the wireless performance and operating modes. 3.7.4.1 Mode Settings Select one of the AP operating modes for different application of Access Point.
15 2 AP Client: Acts as an Ethernet-to-Wireless Bridge, which allows a LAN or a single computer station (no driver installation is need) to join a wireless ESS network through it. You must m ake sure SSID and Channel is set the same as that AP you wish to connect.
3 Wireless Bridge: A pair of APs operating under Bridge m ode to act as the bridge that connect two Ethernet networks or Ethern et enabled clients together. You must mak e sure that th e SSID and Channel is set the same as that AP you wish to connect.
17 5 Repeat Mode : It is able to extend the effective ra nge and coverage of the wireless network. Please make sure the SSID is the same as that AP you want to extend. W ireless LAN is Half Duplex, so one transaction pass-th rough 2 wireless its real data-ra te will be half of normal one.
‘SuperG based’ product is availa ble. If no, the connection is via ‘normal’ G. Static turbo means it will not go back to ‘norm al’ G once it starts • Antenna Power Transmit : Select the Antenna Power transmit f or wireless interface. 3.7.
19 MAC Filter: MAC Filter function controls the MAC of the network de vices that are listed in this table for access authorization or denial. When MAC Filter is enabled, by sele cting the “ Enabled .
• Enable 802.1x security by selecting “Enable”. • If MD5 EAP method is used then you can skip step 2 and go to step 3. • Select the Encryption Key Length Size ranging from 64 to 128 Bits that you would like to use. Select the Lifetime of the Encryption Ke y from 5 Minutes to 1 Day.
21 3.7.7.1 (Save/Load)Settings • Backup Settings: Click on “ Backup ” button, which will open a FileSave Dialog box, where you get to save all the current se ttings and configur ations to a file.
3.8 Configuration through AP Utility (Optional) Launch Setup.exe (CDRom:Utilitys etup.e xe) to install tha AP Utility. 3.8.1 Link Information Link information is showing you the rela ted current setti ng of the first.
23.
3.8.2 AP Settings Basic Setting: • ESSID: It is used by all wireless devi ces within the wireless network. • Channel: Select the appropriate channel from th e dropping list. All wi reless devices with the same ESSID will automatically u se this ch annel to communicate with this access point.
25 • Repeat Mode: It is able to extend the ef fective range and coverage of th e wirele ss network. Please make sure the SSID is the same as that AP you want to extend. 3.8.2.1 Advanced Settings • SSID Broadcast: While SSID Broadcast is en abled, all wireless clients wi ll be able to communicate with the access point.
indicates the combination of two channels to enhance the throughput. Super G without turbo indicates that it is on Super G mode without the channel’ s combination. Dynamic turbo is able to automatically detect if any ‘SuperG based’ product is available.
27 3.8.4 Security • Data Encryption: please tick it if you like to have W EP key as the encryption mechanism. • Authentication Mode: The authentication type default is set to open system . There are four options: open system; shared key; WP A; WP A-PKS.
3.8.5 802.1X Settings There are three essen tial components to the 802.1x infras tructure: (1) Supplicant, (2) Authenticator and (3) Server. The Access Point se rves as a n Authenticator, and the EAP methods used must be supported by the backend Radius Server.
29 If users like to set 802.1X or the authentication t ype is set to WP A, please enable 802.1X function by ticking it. • Encryption Key: Select the Encryption Key Length Size ranging from 64 to 128 Bits that you would like to use. • Lifetime : Select the Lifetim e of the Encryption Ke y from 5 Minutes to 1 Day .
30 APPENDIX A Super G SuperG™ is an assemble of solutions that are Atheros® properties .They allow you to obtain performances far superior to the IEEE802.
31 Maximum theoretical limits* Standard Channel Modulation Max Link- Rate Max Throughput(TCP) Max Throughput(UDP) 802.11b 3 CCK 11Mbps 5.9 Mbps 7.1 Mbps 802.11b and 802.11g 3 CCK/OFDM 54Mbps 14.4 Mbps 19.5 Mbps 802.11g only 3 CCK/OFDM 54Mbps 24.4 Mbps 30.
APPENDIX B Technical Features Physical Interfaces LAN: 1 RJ45 10/100 Base-TX Fast Ethernet Wireless 54Mbps (IEEE802.11g) and 11Mbps (IEEE802.11b) 3 Led for easy diagnostic Reset Wireless Interface Chipset Atheros™ Dipole External removable (reverse SMA) Antenna Radio Spec.
33 Physical and Environmental Power Consumation: (5V ± 5%, 2.4A AC Adapter) Dimensions: 145mm*110mm*35mm Weight: 350g Temperature: Operating:[0°C to 49°C], Storage:[-20°C to 65°C] Humidity: 5-95%.
APPENDIX C Glossary Access Point An interview networking device that seamlessly connects wired and wireless networks Authentication Authentication refers to the verification of a trans mitted message’s integ r ity. DMZ DMZ (DeMilitarized Zone) is a part of a network that is located between a secure LAN and an insecure WAN.
35 FTP FTP (File Transfer Protocol) is used to transfer f iles over a TCP/IP network, a nd is typically used for transferring large files or upl oading the HTML pages for a Web site to the Web server. Gateway Gateways are computers that convert protocols enabling different networks, applications, and operating systems to exchange information.
MTU MTU (Maximum Transmission/Tran sfer Unit) is the largest packet size that can be sent over a network. Messages larger than the MTU are divided into smaller packets. NAT NAT (Network Address Translation - also known as IP masquerad ing) enab les an organization to present itself to the Intern et with one address.
37 RTS RTS (Request To Send) is a signal sent from the tr ansmitting station to the receiving station requesting permission to transmit d ata. Server Servers are typically powerful and fast machines that store program s and data. The programs and data are shared by client machines (workstations) on the network.
38 APPENDIX D Support If you have any problems with the Wire less AP, please consult this manual. If you continue to have problems you should contact the dealer where you bought this AP.
An important point after buying a device Atlantis Land I-Fly i I-Fly Wireless Access Point (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Atlantis Land I-Fly i I-Fly Wireless Access Point yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Atlantis Land I-Fly i I-Fly Wireless Access Point - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Atlantis Land I-Fly i I-Fly Wireless Access Point you will learn all the available features of the product, as well as information on its operation. The information that you get Atlantis Land I-Fly i I-Fly Wireless Access Point will certainly help you make a decision on the purchase.
If you already are a holder of Atlantis Land I-Fly i I-Fly Wireless Access Point, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Atlantis Land I-Fly i I-Fly Wireless Access Point.
However, one of the most important roles played by the user manual is to help in solving problems with Atlantis Land I-Fly i I-Fly Wireless Access Point. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Atlantis Land I-Fly i I-Fly Wireless Access Point along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center