Instruction/ maintenance manual of the product IPS-RDPE-2 Pelco
Go to page of 20
IPS-RDPE-2 Remote Data Port INSTALLATION/OPERATION C2473M-C (8/06).
.
C2473M-C (8/06) 3 Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description .
4 C2473M-C (8/06) Important Safety Instructions Prior to installation an d use of this product, the following warnings shou ld be obser ved. 1. Installation and servicin g should be done only by qu alified service personnel and conform to all local codes.
C2473M-C (8/06) 5 Description Pelco’ s IPS-RDPE-2 dat a port box is an on-sit e service too l designed f or Spectra III ™ SE, Spectra III, Esprit ® , and ExSit e ™ Series positioning systems. The d ata port b ox gives on -site acc ess for setu p and testi ng of the p ositioning system.
6 C2473M-C (8/06) Mounting Instructions W ALL MOUNTING 1. Open the lid of the IPS-RDPE-2 box. Install two 3/4-inch (1.9 1 cm) conduit fittings (not supp lied). Close the lid of the IPS- RDPE-2 box. 2. Determin e the mounting lo cation for the IPS-RDP E-2.
C2473M-C (8/06) 7 POLE MOUNTING 1. Install the P A402 mount adap ter . Refer t o the instruct ions supplie d with the ad apter . 2. Open the lid of the IPS-RDPE-2 box. Install two 3/4-inch (1.9 1 cm) conduit fittings (not supp lied). Close the lid of the IPS- RDPE-2 box.
8 C2473M-C (8/06) Cable/Wire Requirements and Connector Locations Refer to Figure 3 for a layou t of the data port box connector s. It is important to connec t all four communication wires from the IPS-RDPE-2 to the Spectra III dome system or ExSite system.
C2473M-C (8/06) 9 Wiring Diagrams The IPS-RDPE-2 is design ed to work in both coaxia l cable and un shi elded twisted pair (UTP) vide o transmis sion s ystems.
10 C2473M-C (8/06) Figure 5. Coaxitron Controller with UTP Video – Passive Receiver Only NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximu m wire gauge allowed for U TP is 16 AWG.
C2473M-C (8/06) 11 Figure 6. RS-422 (D or P Protocol) Controller with Coax Video – Point-to-Point Configuration NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximum wire gaug e allowed for two-wire communication is 16 A WG.
12 C2473M-C (8/06) Figure 7. RS-422 (D or P Protocol) Controller with Coax Video – Home Run Configuration NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximum wire gaug e allowed for two-wire communication is 16 A WG.
C2473M-C (8/06) 13 Figure 8. RS-422 (D or P Protocol) Controller with Coax Video – Daisy-Chain Configuration NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximum wire gaug e allowed for two-wire communication is 16 A WG.
14 C2473M-C (8/06) Figure 9. RS-422 (D or P Protocol) Controller with UTP Video – Point-to-Point Configuration NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximu m wire gauge allowed for U TP is 16 AWG.
C2473M-C (8/06) 15 Figure 10. RS-422 (D or P Protocol) Controller wit h UTP Video – Home Run Configuration NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximu m wire gauge allowed for U TP is 16 AWG.
16 C2473M-C (8/06) Figure 11. RS-422 (D or P Protocol) Controller wit h UTP Vid eo – Daisy-Chain Configuration NOTES: • Input po wer for the IPS-RDPE-2 is 24 VAC only . The max imum wire gau ge allowed fo r power inpu t and outp ut is 12 AWG. • The maximu m wire gauge allowed for U TP is 16 AWG.
C2473M-C (8/06) 17 Operation T o view video, control pan /tilt/zoom, or upload rev ised operat ing software a nd language files to a p ositioning s ystem, do the f ollowing: 1. Open th e door of t he IPS-RDPE-2. Opening the door will auto matically disconne ct the controller at the head-e nd and trigger an audible alert at the IPS-RD PE-2 site .
18 C2473M-C (8/06) Specifications ELECTRICAL Input V oltage 24 V AC Power Consumpt ion 1 V A Does not inc lude power required fo r position ing system MECHANICAL Construction Aluminum Finish Gray polyester powder coat Cable Entry T wo hole plugs will accommodate 3/4-inch (1.
The materials used in the manufacture of this docume nt and it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components tha.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco IPS-RDPE-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco IPS-RDPE-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco IPS-RDPE-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco IPS-RDPE-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco IPS-RDPE-2 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco IPS-RDPE-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco IPS-RDPE-2.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco IPS-RDPE-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco IPS-RDPE-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
