Instruction/ maintenance manual of the product RS-232 Patton electronic
Go to page of 9
USER MANUAL MODEL 1035 Powered High Speed Short Range Modem RS-232 and V .35 versions SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1035 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
3.0 CONFIGURA TION The Model 1035 provides sixteen configuration switches, which allow selection of data rates, clocking methods, V .54 test modes, RTS/CTS delay and DTE control of test functions. This section describes switch locations and explains all possible switch configurations.
SWITCH SET SW1 The configuration switches on switch set SW1 set analog loopback, digital loopback and V .54 enable/disable. The default settings are summarized in Figure 3 (below).
SW2-4 and SW2-5: Clock Source Switches SW2-4 and SW2-5 are set in combination to determine the synchronous clock source for the Model 1035. SW2-4 SW2-5 Setting On On Internal transmit clock Off On Rec.
When connecting two Model 1035s, it is necessary to use a twisted pair “crossover” cable. The diagram below shows how a crossover cable should be constructed for an environment where both Model 1035s use a 6-wire RJ-1 1 connector . Similar logic should be followed when using RJ-45 connectors or a combination of the two.
5.0 OPERA TION Once the Model 1035 is properly configured and installed, it should operate transparently—as if it were a standard cable connection. Section 5.0 describes reading the LED status monitors, powering-up and using the built-in V .52 and V .
APPENDIX A P A TTON MODEL 1035 SPECIFICA TIONS T ransmission Format: Synchronous T ransmission Line: Unconditioned twisted pair 19 - 26 AW G Clocking: Internal, external or receive loopback Distance: T o 6 miles Interfaces: EIA RS-232, CCITT V .24, CCITT V .
APPENDIX B PIN CONFIGURA TIONS 15 APPENDIX C BLOCK DIAGRAM 16 1 - (FG) Frame Ground Common 2 - (TD) T ransmit Data T o Model 1035 3 - (RD) Receive Data From Model 1035 4 - (RTS) Request to Send T o Mo.
An important point after buying a device Patton electronic RS-232 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic RS-232 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic RS-232 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic RS-232 you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic RS-232 will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic RS-232, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic RS-232.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic RS-232. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic RS-232 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
