Instruction/ maintenance manual of the product Model 1065 Patton electronic
Go to page of 13
USER MAN U AL M M O O D D E E L L 1 1 0 0 6 6 5 5 Industrial Synchronous & Asynchronous Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPO R T (301) 975-1007 http://ww w .
1 2 1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1065 components to be free from defects, and will—at our option—repair or replace the prod- uct should it fail within one year from the first date of shipment.
3 4 2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected by Patton's qualified tech- nicians. If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics T echnical Support at (301) 975-1007.
5 6 The Model 1065 SRM has three sets of eight switches, yielding 24 total DIP switches. The three sets will be referred to as S1, S2 and S3. As Figure 2 shows, the orientation of all DIP switches is the same with respect to “ON” and “OFF” positions.
7 8 Switch S1-8: Carrier Control Method The setting for switch S1-8 determines whether the carrier is “con- stantly on” or “controlled by RTS”. This setting allows for operation in switched carrier , multipoint and/or hardware handshaking applications.
9 10 3.4 CONFIGURA TION SWITCH SET “S3” The DIP switches on S3 set the anti-stream control, local loopback enable, remote loopback enable and receive (input) impedance levels for the Model 1065. Factory default positions of Switch S3 are shown in the table below .
11 12 Switch S3-5: RS-232 Initiation of Local Loopback T est The setting for switch S3-5 determines whether or not the Model 1065 local analog loopback test can be initiated by raising pin 18 on the RS-232 interface.
13 14 4.1.1 T wo-Wire Cable Connection Via RJ-45 A. The RJ-45 jack on a Model 1065 Series Short Range Modem is prewired for a standard TELCO wiring environment.
15 16 C. A T&T standard modular color codes: 4.3 FOUR-WIRE, MUL TIPOINT INST ALLA TION Multipoint operation involves the connection of several terminals to one host port. In such an application, one local Model 1065 is used as a master unit, and it is connected to several remote Model 1065s that are acting as slaves.
17 18 5.0 OPERA TION Once you have configured each Model 1065 Series unit properly and connected the twisted pair and RS-232 cables (see Section 4.0), you are ready to operate the units. This section describes reading the LED status monitors, powering-up and using the built-in V .
19 20 5.3 POWER-UP Apply AC power to the Model 1065 by plugging the separate AC power cable first into the rear panel of the Model 1065 and then into an acceptable AC power outlet.
21 22 5.5 POWER-DOWN T urn off the Model 1065 Series by simply unplugging the AC power cord from the wall. There is no power switch. APPENDIX A P A TTON ELECTRONIICS MODEL 1065 SPECIFICA TIONS T ransmission Format: Synchronous or asynchronous, 2- wire/half duplex, or 4-wire/full or half duplex Interface: RS-232 (CCITT V .
23 24 APPENDIX B P A TTON ELECTRONICS MODEL 1065 F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description 0805FR........................
An important point after buying a device Patton electronic Model 1065 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic Model 1065 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic Model 1065 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic Model 1065 you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic Model 1065 will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic Model 1065, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic Model 1065.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic Model 1065. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic Model 1065 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
