Instruction/ maintenance manual of the product Model 1058 Patton electronic
Go to page of 17
USER MANUAL MODEL 1058 VDSL Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M1058-A Doc# 058091U A Revised 10/12/01 An ISO-9001Cer tified Company.
2 1.0 Warranty Information .................................................................. 3 1.1 Radio and TV Interference ............................................................ 3 1.2 CE Notice ................................................
3 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 1058 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment.
4 1.2 CE NOTICE The CE symbol on your P atton Electronics equipment indicates that it is in compliance with the Electromagnetic Compatibility (EMC) directive and the Low V oltage Directive (L VD) of the European Union (EU). A Cer- tificate of Compliance is av ailab le by contacting T echnical Suppor t.
5 2.0 GENERAL INFORMATION Thank you f or y our purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or parts and labor . If any questions or problems arise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007.
6 Figure 1. T ypical application The 1058D V/CO and 1058D V/CP work together to create a transparent e xtension between two peered Ethernet LANs. PO TS/ISDN calls can be made ov er the VDSL link without interfering with the data. Figure 1 shows a typical point-to-point application.
7 3.0 INSTALLATION Because the Model 1058 requires no configuration, it can be installed and made operational quic kly . Installation tak es place as f ollows: 1. Connecting the line interf ace between the units (ref er to section 3.1, “Connecting the T wisted-P air Line Interface” on page 7) Note See Figure 2 for the rear panel arr angements.
8 F ollow the steps belo w to connect the Model 1058 VDSL Interfaces. Note The Model 1058 units work in pairs. One of the units must be a Model 1058/CO (Central Of fi ce), and the other unit must be a Model 1058/CP (Customer Premise). It does not matter which end is the 1058/CO and which is the 1058/CP .
9 Figure 4. Model 1058D (T er minal Block) twisted pair line interface . 3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ-45 por t labeled Ethernet is the 10/100Base-T interf ace. This por t is designed to connect directly to a 10/100Base-T network.
10 straight-through RJ-45 cab le. Figure 6 diagrams the cab le wiring for con- necting the Model 1058 to a 10/100Base-T hub . Figure 6. Wiring diagram for connecting the Model 1058 to a 10/100Base-T h.
11 work. The RJ-45 connector in the model 1058 ’ s PO TS/ISDN interface is wired as shown in Figure 8. Figure 8. Model 1058D V (RJ-45) POTS/ISDN interf ace 3.4 CONNECTING POWER An e xternal AC or DC pow er supply is av ailab le separately . This connec- tion is made via the barrel jack on the rear panel of the Model 1058.
12 4.0 OPERATION Once the Model 1058s are properly installed, they should operate trans- parently . No user settings required. This section describes reading the LED status monitors. 4.1 POWER UP Bef ore applying power to the Model 1058, please re view section 3.
13 T able 1: F ront panel LED description LED Description P o wer Solid GREEN to indicate the unit is powered on. VDSL Link (Active Green) Solid g reen (ON) to indicate that the end-to-end VDSL link betw een the Model 1058s is established. The VDSL LED is OFF when the link is down.
14 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T , IEEE 802.3 Ethernet • VDSL Connection: RJ-45 and T er minal Block A.2 T RANSMISSION LINE T wo-wire unconditioned twisted pair A.3 VDSL LINE RATE 12.5 Mbps, symmetric upstream/downstream.
15 APPENDIX B MODEL 1058 SERIES F ACTORY REPLACEMENT P ARTS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 1058D/CO CO VDSL Modem, da.
16 APPENDIX C MODEL 1058 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE: RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 VDSL INTERFACE: RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection T erminal Block See Figure 4 on page 9.
17.
An important point after buying a device Patton electronic Model 1058 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic Model 1058 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic Model 1058 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic Model 1058 you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic Model 1058 will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic Model 1058, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic Model 1058.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic Model 1058. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic Model 1058 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
